Engine Characteristic Studies by Application of Antioxidants and Nanoparticles as Additives in Biodiesel Diesel Blends

2018 ◽  
Vol 140 (8) ◽  
Author(s):  
A. Prabu
Keyword(s):  
Direct Injection ◽  
High Surface ◽  
High Surface Area ◽  
Injection Pressure ◽  
Injection Timing ◽  
No Emission ◽  
Brake Thermal Efficiency ◽  
Unburned Hydrocarbon ◽  
Di Diesel Engine ◽  
Smoke Opacity

This study evaluates the outcomes of antioxidants and nanoparticles as additives with biodiesel diesel blends on the engine working characteristics, carried on a single cylinder direct injection (DI) diesel engine, operated at invariable engine speed of 1500 rpm, invariable injection timing of 26 deg before top dead center with invariable injection pressure of 216 bar, under five different engine load conditions (0.08, 0.15, 0.23, 0.30, 0.45, and 0.53 MPa). The antioxidants and nanoparticles blended test fuels are used as fuels in this experimental investigation. The antioxidant as additive in fuel found to be more effective in suppressing the NO emission by disrupting the chain propagating reactions, trapping free radicals, and decomposing peroxides. The high surface area to volume of the nanoparticles acts as fuel borne catalyst by ameliorating the engine working characteristics and downplays the NO emission by buffering the oxygen molecule. The obtained experimental results indicates that B20SNAlCe test fuel enhances engine brake thermal efficiency (BTE) by 13% and reduces level of pollutants such as unburned hydrocarbon (UBHC) by 38%, nitric oxide by 32%, smoke opacity by 21%, and carbon monoxide by 60% in compared with B100.

scholarly journals Influence of Ultra Injection Pressure with Dynamic Injection Timing on CRDI Engine Performance Using Simarouba Biodiesel Blends

2018 ◽  
Vol 15 (4) ◽  
pp. 5748-5759
Author(s):  
Srinath Pai ◽  
Abdul Sharief ◽  
Shiva Kumar
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Injection Timing ◽  
Brake Thermal Efficiency ◽  
High Speed Diesel ◽  
Performance And Emissions ◽  
Smoke Opacity

A single cylinder diesel engine upgraded to operate Common Rail Direct Injection (CRDI) system and employed in this investigation. Tests were conducted on this engine using High-Speed diesel (HSD) and Simarouba biodiesel (SOME) blends to determine the influence of Injection Pressure (IP) and Injection Timing (IT) on the performance and emissions. Four unique IP of 400 bar to 1000 bar, in steps of 200 bar and four differing ITs of 10°, 13°, 15° and 18° before Top Dead Center (bTDC) combinations were attempted for the 25% to full load. Compression Ratio (CR) of 16.5 and Engine speed of 1500 RPM was kept constant during all trails. Critical performance parameter like Brake Thermal Efficiency (BTE) and Brake Specific Fuel Consumption (BSFC) were analyzed, primary emission parameters of the diesel engine The NOx and Smoke opacity were recorded. Finally, the outcomes of each combination were discussed.

Effect of Injection Timing on Combustion Characteristics of a DI Diesel Engine Fuelled with Pistacia chinensis Bunge Seed Biodiesel

2012 ◽  
Vol 614-615 ◽  
pp. 337-342
Author(s):  
Li Luo ◽  
Bin Xu ◽  
Zhi Hao Ma ◽  
Jian Wu ◽  
Ming Li
Keyword(s):  
Combustion Temperature ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Brake Specific Fuel Consumption ◽  
Cylinder Pressure ◽  
Combustion Duration ◽  
Di Diesel Engine ◽  
Maximum Combustion Temperature

In this study, the effect of injection timing on combustion characteristics of a direct injection, electronically controlled, high pressure, common rail, turbocharged and intercooled engine fuelled with different pistacia chinensis bunge seed biodiesel/diesel blends has been experimentally investigated. The results indicated that brake specific fuel consumption reduces with the increasing of fuel injection advance angle and enhances with the increasing of biodiesel content in the blends. The peak of cylinder pressure and maximum combustion temperature increase evidently with the increment of fuel injection advance angle. However, the combustion of biodiesel blends starts earlier than diesel at the same fuel injection advance angle. At both conditions, the combustion duration and the peak of heat release rate are insensitive to the changing of injection timing.

Experimental Evaluation of Compression Ignition Engine Fueled with Cashew Nut Shell Liquid Diesel Blend with the Effect of Various Injection Pressures

2015 ◽  
Vol 787 ◽  
pp. 717-721
Author(s):  
Sangeetha Krishnamoorthy ◽  
K. Rajan ◽  
K.R. Senthil Kumar ◽  
M. Prabhahar
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Injection Pressure ◽  
Cashew Nut Shell Liquid ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Performance And Emission ◽  
Full Load ◽  
Cashew Nut ◽  
Cashew Nut Shell

This paper investigates the performance and emission characteristics of 20% cashew nut shell liquid (CNSL)-diesel blend (B20) in a direct injection diesel engine. The cashew nut shell liquid was prepared by pyrolysis method. The test was conducted with various nozzle opening pressures like 200 bar, 225 bar and 250 bar at different loads between no load to full load. The results showed that the brake thermal efficiency was increased by 2.54% for B20 with 225 bar at full load. The CO and smoke emissions were decreased by 50% and 14% respectively and the NOx emission were decreased slightly with 225 bar injection pressure compared with 200 bar and 250 bar at full load. On the whole, it is concluded that the B20 CNSL blend can be effectively used as a fuel for diesel engine with 225 bar injection pressure without any modifications.

Evaluation of Fuel Injection Strategies for Biodiesel-Fueled CRDI Engine Development and Particulate Studies

2018 ◽  
Vol 140 (10) ◽  
Author(s):  
Akhilendra Pratap Singh ◽  
Avinash Kumar Agarwal
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Pressure Rise ◽  
Injection Pressure ◽  
Combustion Noise ◽  
Emission Characteristics ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
Injection Parameters ◽  
Smoke Opacity

Fuel injection parameters such as fuel injection pressure (FIP) and start of main injection (SoMI) timings significantly affect the performance and emission characteristics of a common rail direct injection (CRDI) diesel engine. In this study, a state-of-the-art single cylinder research engine was used to investigate the effects of fuel injection parameters on combustion, performance, emission characteristics, and particulates and their morphology. The experiments were carried out at three FIPs (400, 700, and 1000 bar) and four SoMI timings (4 deg, 6 deg, 8 deg, and 10 deg bTDC) for biodiesel blends [B20 (20% v/v biodiesel and 80% v/v diesel) and B40 (40% v/v biodiesel and 60% v/v diesel)] compared to baseline mineral diesel. The experiments were performed at a constant engine speed (1500 rpm), without pilot injection and exhaust gas recirculation (EGR). The experimental results showed that FIP and SoMI timings affected the in-cylinder pressure and the heat release rate (HRR), significantly. At higher FIPs, the biodiesel blends resulted in slightly higher rate of pressure rise (RoPR) and combustion noise compared to baseline mineral diesel. All the test fuels showed relatively shorter combustion duration at higher FIPs and advanced SoMI timings. The biodiesel blends showed slightly higher NOx and smoke opacity compared to baseline mineral diesel. Lower particulate number concentration at higher FIPs was observed for all the test fuels. However, biodiesel blends showed emission of relatively higher number of particulates compared to baseline mineral diesel. Significantly lower trace metals in the particulates emitted from biodiesel blend fueled engine was an important finding of this study. The particulate morphology showed relatively smaller number of primary particles in particulate clusters from biodiesel exhaust, which resulted in relatively lower toxicity, rendering biodiesel to be more environmentally benign.

Experimental and Numerical Analysis on the Influence of Direct Fuel Injection Into O2-Depleted Environment of a GDI-HCCI Engine

2020 ◽  
Author(s):  
Ratnak Sok ◽  
Jin Kusaka
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Single Pulse ◽  
Gasoline Direct Injection ◽  
Injection Timing ◽  
Rich Mixture ◽  
Intake Stroke ◽  
Shift Reaction ◽  
Direct Fuel Injection

Abstract Injected gasoline into the O2-depleted environment in the recompression stroke can be converted into light hydrocarbons due to thermal cracking, partial oxidation, and water-gas shift reaction. These reformate species influence the combustion phenomena of gasoline direct injection homogeneous charge compression ignition (GDI-HCCI) engines. In this work, a production-based single-cylinder research engine was boosted to reach IMEPn = 0.55 MPa in which its indicated efficiency peaks at 40–41%. Experimentally, the main combustion phases are advanced under single-pulse direct fuel injection into the negative valve overlap (NVO) compared with that of the intake stroke. NVO peak in-cylinder pressures are lower than that of motoring, which emphasizes that endothermic reaction occurs during the interval. Low O2 concentration could play a role in this evaporative charge cooling effect. This phenomenon limits the oxidation reaction, and the thermal effect is not pronounced. For understanding the recompression reaction phenomena, 0D simulation with three different chemical reaction mechanisms is studied to clarify that influences of direct injection timing in NVO on combustion advancements are kinetically limited by reforming. The 0D results show the same increasing tendencies of classical reformed species of rich-mixture such as C3H6, C2H4, CH4, CO, and H2 as functions of injection timings. By combining these reformed species into the main fuel-air mixture, predicted ignition delays are shortened. The effects of the reformed species on the main combustion are confirmed by 3D-CFD calculation, and the results show that OH radical generation is advanced under NVO fuel injection compared with that of intake stroke conditions thus earlier heat release and cylinder pressure are noticeable. Also, parametric studies on injection pressure and double-pulse injections on engine combustion are performed experimentally.

Effect of High Pressure Post Injection on Soot and NO Trade-Off in a DI Diesel Engine

2010 ◽  
Author(s):  
Kamran Poorghasemi ◽  
Fathollah Ommi ◽  
Vahid Esfahanian
Keyword(s):  
Diesel Engine ◽  
Soot Formation ◽  
Three Dimensional ◽  
Injection Pressure ◽  
Combustion Mechanism ◽  
Injection Timing ◽  
Post Injection ◽  
Multiple Injection ◽  
Trade Off ◽  
Di Diesel Engine

In DI Diesel engines NO and Soot trade off is an important challenge for Engineers. In this paper, at first, multiple injection strategy will be introduced as a useful way to reduce both NO and Soot emissions simultaneously. Then the effect of injection pressure in post injection on the engine emissions will be studied. Investigations have been conducted on DI diesel engine. To evaluate the benefits of multiple injection strategies and to reveal combustion mechanism, modified three dimensional CFD code KIVA-3V was used. Results showed that using post injection with appropriate dwell between injection pulses can be effective in simultaneously reduction of emissions. Based on computation results, NO reduction formation mechanism is a single injection with retarded injection timing. It is shown that reduced soot formation is because of the fact that the soot producing rich regions at the fuel spray head are not replenished by new fuel when the injection is stopped and then restarted. Also increasing injection pressure in post injection will reduce the Soot emission dramatically while NO is in control and it is due to increasing fuel burning rate in post injection pulse.

Distribution of Two-Stage Direct Injection CNG-Air Mixture near Lean Limit Using CFD

2013 ◽  
Vol 465-466 ◽  
pp. 448-452
Author(s):  
Mas Fawzi ◽  
Bukhari Manshoor ◽  
Yoshiyuki Kidoguchi ◽  
Yuzuru Nada
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Gas Jet ◽  
Exhaust Emission ◽  
Injection Technique ◽  
Injection Timing ◽  
Two Stage ◽  
Lean Burn

Previous work shows that gas-jet ignition with two-stage injection technique is effective to extend lean combustible ranges of CNG engines. In this report, the robustness of the gas-jet ignition with two-stage injection method was investigated purposely to improve the performance of a lean burn direct injection CNG engine. The experiment was conducted using an engine at speed of 900 rpm, fuel-injection-pressure of 3MPa, equivalence ratio at 0.8, and ignition timing at top dead center. The effect of first injection timing on the test engine performance and exhaust emission was analyzed. First injection timings near the gas-jet ignition produced unstable combustion with occurrence of misfires except at a timing which produced distinctively good combustion with low HC and CO emissions. Computational fluid dynamics was used to provide hindsight of the fuel-air mixture distribution that might be the cause of misfires occurrence at certain injection timings.

Study And Evaluation of Injection Timing of CIDI Engine Injection Pump Using Alternate Fuel i.e Biodiesel Fuel

2016 ◽  
Vol 8 (01) ◽  
pp. 11-19
Author(s):  
P. K. Singh ◽  
Rohit K. Shrivastava ◽  
K. G. Sinha
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Gas Temperature ◽  
Engine Exhaust ◽  
Brake Thermal Efficiency ◽  
Injection Pump ◽  
Alternate Fuel ◽  
Exhaust Gas Temperature

In this investigation an experimental study of the effects of FIP injection timing on Specific Fuel Consumption(SFC), Brake Thermal Efficiency(BTE), Engine Exhaust Gas Temperature(EEGT), CO, HC, NOX and Smoke of “Kirloskar- 6R1080TA, 6-CylinderInline, Direct Injection, Turbocharged Intercooled, 191 hp Diesel Engine” has been conducted. Injection Timing retardation method has been utilised to reduce SFC, EEGT, CO, HC, NOX, Smoke and increase BTE of Kirloskar-6R1080TA Diesel Engine. The Kirloskar 6R1080TA engine has been tested for six different injection timings (23°, 21°, 20°, 19°, 18° and 17° CA BTC) at same engine speeds and load conditions. The SFC,EEGT, CO, HC, NOX and Smoke of engine are approximately higher and BTE lower for injection timings at 23°, 21°, 20°, 18° and 17° CA BTC than 19° CA BTC at same speed and load. The results are showing that SFC,EEGT,CO,HC,NOX and Smoke are approximately reduces and BTE increases by reducing injection timing from 23° CA BTC to 19° CA BTC. Optimum FIP injection timing for Kirloskar 6R1080TA engine has been achieved at 19° CA BTC.

Investigation on the combustion noise of a pilot-ignited direct-injection natural-gas engine

2016 ◽  
Vol 230 (14) ◽  
pp. 1942-1957 ◽  
Author(s):  
Menghan Li ◽  
Qiang Zhang ◽  
Guoxiang Li
Keyword(s):  
Natural Gas ◽  
Direct Injection ◽  
Injection Pressure ◽  
Pressure Level ◽  
Combustion Noise ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Engine Load ◽  
Gas Engine ◽  
Natural Gas Engine

In this paper, the effects of the injection timing, the injection pressure and the engine load on the combustion noise of a pilot-ignited direct-injection natural-gas engine were explored by analysing the separate components of the in-cylinder pressure. The results suggested that retarding the injection timing and reducing the injection pressure are effective ways of controlling the combustion noise. This can be attributed to the promoted burning rate at advanced injection timings and to the increased injection pressure. However, the effect of the engine load seems to be less obvious, although the resonance pressure level appears to increase with increasing engine load; the estimated combustion noise shows a decreasing tendency.

Sign in / Sign up

Export Citation Format

Share Document