Numerical Simulation and Stereo PIV Test of Inner Flow in a Double Blades Pump

2011 ◽  
Author(s):  
Kai Wang ◽  
Houlin Liu ◽  
Shouqi Yuan ◽  
Minggao Tan ◽  
Yong Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Velocity Field ◽  
Cfd Simulation ◽  
Research Work ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Absolute Velocity ◽  
Operation Condition ◽  
Test Technique ◽  
Simulation Results

A double blades pump is widely used in sewage treatment industry, while at present the research on the internal flow characteristics of the double blades pump is very few. So, the CFD technology and the stereo PIV test technique are applied to study the inner flow in a double blades pump whose specific speed is 110.9. The commercial code FLUENT is used to simulate the inner flow in the double blades pump at 0.6Qd, 0.8Qd, 1.0Qd, 1.2Qd and 1.4Qd. The RNG k-ε turbulence model and SIMPLEC algorithm are used in FLUENT. According to the results of the three-dimensional steady numerical simulation, the distributions of velocity field in the impeller are obtained at the five different operating conditions. The analysis of the numerical simulation results shows that there is an obvious vortex in the impeller passage at off-design conditions. But the number, location and area of the vortex are different from each operation condition. In order to validate CFD simulation results, the stereo PIV is used to test the absolute velocity distribution in the double blades pump at Jiangsu University. The distributions of three-dimensional absolute velocity field at the above five different operating conditions are obtained by the PIV test, and the measured results are compared with the CFD simulation results. The comparison indicates that there are vortexes in impeller passages of the double blades pump under the five operating conditions. But as to the area of the vortex and the relative velocity values of the vortex core, there are some differences between the experiment results and the numerical simulation results. The research work can be applied to instruct the hydraulic design of double blades pumps.

Numerical Simulation of Gas Flow and Heat Transfer in Cross-Wavy Primary Surface Channel for Microtubine Recuperators

2005 ◽  
Author(s):  
H. X. Liang ◽  
Q. W. Wang ◽  
L. Q. Luo ◽  
Z. P. Feng
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Gas Turbine ◽  
Numerical Study ◽  
High Reliability ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Flow And Heat Transfer ◽  
High Heat Transfer ◽  
The Cross

Three-dimensional numerical simulation was conducted to investigate the flow field and heat transfer performance of the Cross-Wavy Primary Surface (CWPS) recuperators for microturbines. Using high-effective compact recuperators to achieve high thermal efficiency is one of the key techniques in the development of microturbine in recent years. Recuperators need to have minimum volume and weight, high reliability and durability. Most important of all, they need to have high thermal-effectiveness and low pressure-losses so that the gas turbine system can achieve high thermal performances. These requirements have attracted some research efforts in designing and implementing low-cost and compact recuperators for gas turbine engines recently. One of the promising techniques to achieve this goal is the so-called primary surface channels with small hydraulic dimensions. In this paper, we conducted a three-dimensional numerical study of flow and heat transfer for the Cross-Wavy Primary Surface (CWPS) channels with two different geometries. In the CWPS configurations the secondary flow is created by means of curved and interrupted surfaces, which may disturb the thermal boundary layers and thus improve the thermal performances of the channels. To facilitate comparison, we chose the identical hydraulic diameters for the above four CWPS channels. Since our experiments on real recuperators showed that the Reynolds number ranges from 150 to 500 under the operating conditions, we implemented all the simulations under laminar flow situations. By analyzing the correlations of Nusselt numbers and friction factors vs. Reynolds numbers of the four CWPS channels, we found that the CWPS channels have superior and comprehensive thermal performance with high compactness, i.e., high heat transfer area to volume ratio, indicating excellent commercialized application in the compact recuperators.

Hydraulic Characteristics of the New Type Bulb Turbine With Micro-Head

2013 ◽  
Author(s):  
Lingyu Li ◽  
Yuan Zheng ◽  
Daqing Zhou ◽  
Zihao Mi
Keyword(s):  
Numerical Simulation ◽  
Cfd Simulation ◽  
Guide Vane ◽  
Three Dimensional ◽  
Flow Distribution ◽  
Three Dimensions ◽  
Guide Vanes ◽  
Runner Blade ◽  
Cfd Method ◽  
Bulb Turbine

The head of low-head hydropower stations is generally higher than 2.5m in the world, while micro-head hydropower resources which head is less than 2.5m are also very rich. In the paper, three-dimensional CFD method has been used to simulate flow passage of the micro-head bulb turbine. The design head and unit flow of the turbine was 1m and 3m3/s respectively. With the numerical simulation, the bulb turbine is researched by analyzing external characteristics of the bulb turbine, flow distribution before the runner, pressure distribution of the runner blade surface, and flow distribution of the outlet conduit under three different schemes. The turbine in second scheme was test by manufactured into a physical model. According to the results of numerical simulation and model test, bulb turbine with no guide vane in second scheme has simpler structure, lower cost, and better flow capacity than first scheme, which has traditional multi-guide vanes. Meanwhile, efficiency of second scheme has just little decrease. The results of three dimensions CFD simulation and test results agree well in second scheme, and higher efficiency is up to 77% which has a wider area with the head of 1m. The curved supports in third scheme are combined guide vanes to the fixed supports based on 2nd scheme. By the water circulations flowing along the curved supports which improve energy transformation ability of the runner, the efficiency of the turbine in third scheme is up to 82.6%. Third scheme, which has simpler structure and best performance, is appropriate for the development and utilization of micro-head hydropower resources in plains and oceans.

scholarly journals MEMS-Based Integrated Triaxial Electrochemical Seismometer

Micromachines ◽  
2021 ◽  
Vol 12 (10) ◽  
pp. 1156
Author(s):  
Wenjie Qi ◽  
Bowen Liu ◽  
Tian Liang ◽  
Jian Chen ◽  
Deyong Chen ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Ground Motion ◽  
Small Volume ◽  
Three Dimensional ◽  
Experimental Results ◽  
Good Prospect ◽  
High Symmetry ◽  
Noise Levels ◽  
Sensitivity Curves ◽  
Simulation Results

This paper presents a micro-electromechanical systems (MEMS)-based integrated triaxial electrochemical seismometer, which can detect three-dimensional vibration. By integrating three axes, the integrated triaxial electrochemical seismometer is characterized by small volume and high symmetry. The numerical simulation results inferred that the integrated triaxial electrochemical seismometer had excellent independence among three axes. Based on the experimental results, the integrated triaxial electrochemical seismometer had the advantage of small axial crosstalk and could detect vibration in arbitrary directions. Furthermore, compared with the uniaxial electrochemical seismometer, the integrated triaxial electrochemical seismometer had similar sensitivity curves ranging from 0.01 to 100 Hz. In terms of random ground motion response, high consistencies between the developed integrated triaxial electrochemical seismometer and the uniaxial electrochemical seismometer could be easily observed, which indicated that the developed integrated triaxial electrochemical seismometer produced comparable noise levels to those of the uniaxial electrochemical seismometer. These results validated the performance of the integrated triaxial electrochemical seismometer, which has a good prospect in the field of deep geophysical exploration and submarine seismic monitoring.

scholarly journals Prefabricated Urban Underground Utility Tunnels: A Case Study on Mechanical Behaviour with Strain Monitoring and Numerical Simulation

2021 ◽  
Vol 2021 ◽  
pp. 1-14
Author(s):  
Yonggang Xiao ◽  
Jubing Zhang ◽  
Jie Cao ◽  
Changhong Li
Keyword(s):  
Numerical Simulation ◽  
Working Conditions ◽  
Failure Modes ◽  
Mechanical Performance ◽  
Low Cost ◽  
Side Wall ◽  
Operating Conditions ◽  
Land Occupation ◽  
Depth Analysis ◽  
Simulation Results

The prefabricated urban utility tunnels (UUTs) have many advantages such as short construction period, low cost, high quality, and small land occupation. However, there is still a lack of in-depth analysis of the mechanical performance of the prefabricated urban utility tunnel (UUT) structure with bolted connections under different working conditions. In this paper, the force performance of a prefabricated UUT in Tongzhou District, Beijing, was studied under different working conditions using two methods: field monitoring and numerical simulation. The multichannel strain monitor was used for monitoring, and the internal wall concrete and bolt strain change data under the two conditions of installation and backfill were obtained. Combined with the construction process of the UUTs, a three-dimensional numerical model was established by COMSOL, where the build-in bolt assembly was used to simulate the longitudinal connection of the tunnel. The simulation results were compared with the measured data to verify the rationality of the computational model. The simulation results showed that the concrete and bolts on the inner wall of the tunnel work well under the two conditions of installation and backfilling; The deformation of the top plate of the prefabricated tunnel was approximately parabolic, with the largest vertical displacement (0.37 mm) in the middle and the most sensitive to the vertical load in the central part of the roof. The central portion of the side wall had the largest displacement (0.17 mm) in the inner concave. The tensile stress of bolt 3 increased the most (30.75 MPa) but was still much smaller than the yield strength of the bolt. The concrete and bolts of the UUT were found to work well through force analysis under operating conditions. In conclusion, analysis of structural forces and deformation failure modes will help design engineers understand the basic mechanisms and select the appropriate UUT structure.

scholarly journals CFD simulation of gas-liquid floating particles mixing in an agitated vessel

2017 ◽  
Vol 23 (3) ◽  
pp. 377-389 ◽  
Author(s):  
Liangchao Li ◽  
Bin Xu
Keyword(s):  
Velocity Field ◽  
Cfd Simulation ◽  
Solid Phase ◽  
Fluid Model ◽  
Surface Region ◽  
Operating Conditions ◽  
Gas Dispersion ◽  
Agitated Vessel ◽  
Superficial Gas Velocity ◽  
Floating Particles

Gas dispersion and floating particles suspension in an agitated vessel were studied numerically by using computational fluid dynamics (CFD). The Eulerian multi-fluid model along with standard k-? turbulence model was used in the simulation. A multiple reference frame (MRF) approach was used to solve the impeller rotation. The velocity field, gas and floating particles holdup distributions in the vessel were first obtained, and then, the effects of operating conditions on gas dispersion and solid suspension were investigated. The simulation results show that velocity field of solid phase and gas phase are quite different in the agitated vessel. Floating particles are easy to accumulate in the center of the surface region and the increasing of superficial gas velocity is in favor of floating particles off-surface suspension. With increasing solids loading, the gas dispersion becomes worse, while relative solid holdup distribution changes little. The limitations of the present modeling are discussed and further research in the future is proposed.

Numerical Simulation of IAQ under Up-Suction Exhaust Hood in Commercial Kitchen

2011 ◽  
Vol 250-253 ◽  
pp. 3228-3231 ◽  
Author(s):  
Da Hua Jiang ◽  
An Gui Li ◽  
Fa En Shi ◽  
Zhi Hua Wang
Keyword(s):  
Exhaust System ◽  
Operating Conditions ◽  
Airflow Rate ◽  
Exhaust Hood ◽  
Operation Condition ◽  
Main Site ◽  
Actual Operation ◽  
The Common ◽  
Simulation Results ◽  
Save Energy

For particular commercial kitchen, using CFD software to build model according to the actual operation condition uttermost, adopting the exhaust system of up-suction hood, the effect of exhaust airflow rate on working temperature,velocity,CO2 concentration at main site in commercial kitchen is studied. According to the common four calculation methods of airflow rate of exhaust hood, the simulation results shows 4.81 m3/s of exhaust system can realize eliminating harmful gas quickly and effectively, IAQ is good relatively. Based on of it, additional airflow rate can not improve emissions effect and operating conditions obviously, whereas it can be detrimental to save energy. The simulation results help design exhaust system.

Numerical Simulation of the Kinetic Energy Projectile Oblique Penetration into the Concrete

2014 ◽  
Vol 989-994 ◽  
pp. 982-985
Author(s):  
Jun Chen ◽  
Xiao Jun Ye
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Kinetic Energy ◽  
Three Dimensional ◽  
Test Results ◽  
Destruction Process ◽  
3D Finite Element ◽  
Finite Element Software ◽  
Simulation Results ◽  
Target Characteristics

ANSYS-LS/DYNA 3D finite element software projectile penetrating concrete target three-dimensional numerical simulation , has been the target characteristics and destroy ballistic missile trajectory , velocity and acceleration and analyze penetration and the time between relationship , compared with the test results , the phenomenon is consistent with the simulation results. The results show that : the destruction process finite element software can better demonstrate concrete tests revealed the phenomenon can not be observed , estimated penetration depth and direction of the oblique penetration missile deflection .

Research on the CFD numerical simulation and process optimization of countercurrent–cocurrent dissolved air flotation

2019 ◽  
Vol 68 (5) ◽  
pp. 325-336
Author(s):  
Yonglei Wang ◽  
Wei Liu ◽  
Liping Tian ◽  
Ruibao Jia ◽  
Zhenqi Du ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Contact Zone ◽  
Process Optimization ◽  
Operating Conditions ◽  
Cocurrent Flow ◽  
Dissolved Gas ◽  
Dissolved Air Flotation ◽  
Simulation Results ◽  
Air Flotation ◽  
Dissolved Air

Abstract The countercurrent–cocurrent dissolved air flotation (CCDAF) process is a new type of air flotation process integrating countercurrent collision and cocurrent flow adhesion processes. The structural form of the CCDAF tank and its process parameters are the required conditions to achieve countercurrent collision and cocurrent adhesion. In this study, eight CCDAF tank process models were established with a flow rate of 0.5 m3/h. Flow field numerical simulation and process optimization of a CCDAF tank was conducted using Fluent software. The simulation results show that the optimal conditions for the CCDAF process are as follows: contact zone ascending velocity 10 mm/s, separation zone separation velocity 1.5 mm/s, dissolved gas pressure 0.45 MPa, and recirculating dissolved-gas distribution ratio R1/R2 1:1. Under these operating conditions, the flow state in the flotation tank is the most stable and the gas in the contact zone is evenly distributed. According to the simulation results, a 5 m3/h pilot plant was built. The structural dimensions were: B × L × H = 1,020 mm × 1,300 mm × 1,350 mm. The test results show that the CCDAF has a significant decontamination effect and is clearly superior to the cocurrent flow DAF process and countercurrent flow DAF process.

scholarly journals Study on Fluorine Pollution in a Slag Yard

2019 ◽  
Vol 9 (5) ◽  
pp. 847
Author(s):  
Lide Wei ◽  
Changfu Wei ◽  
Sugang Sui
Keyword(s):  
Numerical Simulation ◽  
Experimental Investigation ◽  
Numerical Simulations ◽  
Solute Transport ◽  
Large Scale ◽  
Three Dimensional ◽  
Simulation Method ◽  
Laboratory Studies ◽  
Survey Results ◽  
Simulation Results

This paper suggests a large-scale three-dimensional numerical simulation method to investigate the fluorine pollution near a slag yard. The large-scale three-dimensional numerical simulation method included an experimental investigation, laboratory studies of solute transport during absorption of water by soil, and large-scale three-dimensional numerical simulations of solute transport. The experimental results showed that the concentrations of fluorine from smelting slag and construction waste soil were well over the discharge limit of 0.1 kg/m3 recommended by Chinese guidelines. The key parameters of the materials used for large-scale three-dimensional numerical simulations were determined based on an experimental investigation, laboratory studies, and soil saturation of survey results and back analyses. A large-scale three-dimensional numerical simulation of solute transport was performed, and its results were compared to the experiment results. The simulation results showed that the clay near the slag had a high saturation of approximately 0.9, consistent with the survey results. Comparison of the results showed that the results of the numerical simulation of solute transport and the test results were nearly identical, and that the numerical simulation results could be used as the basis for groundwater environmental evaluation.

Study on the Principle of Yarn Splicing of Pneumatic Splicer Using Numerical Simulation

2012 ◽  
Vol 588-589 ◽  
pp. 1355-1358
Author(s):  
Xiao Xing ◽  
Guo Ming Ye
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Three Dimensional ◽  
Numerical Results ◽  
Simulation Results

During the splicing process of pneumatic splicer, the principle of yarn splicing is closely related to the flow field inside the splicing chamber. This paper presents a numerical simulation of the flow char-acteristics inside the splicing chamber of the pneumatic splicer. A three-dimensional grid and the realizable tur¬bulence model are used in this simulation. The numerical results of veloc¬ity vectors distribution inside the chamber are shown. Streamlines starting from the two air injectors are also acquired. Based on the simulation, the principle of yarn splicing of the pneumatic splicer is discussed. The airflow in the splicing chamber can be divided into three regions. In addition, the simulation results have well sup¬ported the principle of yarn splicing of pneumatic splicer claimed by the splicing chamber makers.

Sign in / Sign up

Export Citation Format

Share Document