Experimental Dynamical Characterization of Beach Tennis Rackets by Modal Analysis

2011 ◽  
Author(s):  
Emiliano Mucchi
Keyword(s):  
Modal Analysis ◽  
Test Results ◽  
Sweet Spot ◽  
Design Development ◽  
Tennis Racket ◽  
Nodal Lines ◽  
Maximum Coefficient ◽  
Incident Kinetic Energy ◽  
First Time

The term sweet spot is used for tennis racket in describing that point or region where the ball should be hit for optimal results. From a vibration standpoint, the sweet spot is determined by the location of the nodal lines across the racket head. In this paper, several methodologies based on modal analysis techniques are explored in order to estimate such a sweet spot for a beach tennis racket. Particular attention was addressed in the detection of the optimal boundary conditions to which the beach tennis racket should be constrained. It is the first time this item is dynamically characterized by experimental techniques. Test results are presented and the sweet spot related to minimal vibration perception is identified for a beach tennis racket. A further experimental study is also carried out in order to identify the Maximum Coefficient of Restitution in beach tennis rackets; this coefficient is related to racket efficiency and characterized by a minimum absorption of the ball incident kinetic energy by the racket. This study could be useful for design, development and practical use of beach tennis rackets.

scholarly journals Preparation and Characterization of Macroalgae Biochar Nanomaterials with Highly Efficient Adsorption and Photodegradation Ability

Materials ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 1709 ◽  
Author(s):  
Yarui Zhou ◽  
Hailong Zhang ◽  
Lu Cai ◽  
Jian Guo ◽  
Yaning Wang ◽  
...  
Keyword(s):  
Transition Metal Oxides ◽  
High Specific Surface Area ◽  
Test Results ◽  
Order Model ◽  
Highly Efficient ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Dyes Adsorption ◽  
First Time

In this study, carbonized kelp biochar (AKB) modified by KOH impregnation and photocatalytic Bi2MoO6/AKB composite (BKBC) nanomaterials were the first time successfully synthesized for efficient removal of dyes in aqueous solution. BET, XRD, FT-IR, and SEM were employed to characterize as-prepared samples. UV-vis and other test results indicated that the removal efficiency of methylene blue (MB) was 61.39% and 94.12% for BKBC and AKB, respectively, which was up to 13 times and 20 times higher in comparison with pure Bi2MoO6 (PBM). In addition, the equilibrium adsorption capacity of MB could reach up to 324.1 mg/g for AKB. This high dyes adsorption performance could be likely attributed to its high specific surface area (507.177 m2/g) and its abundant presence of various functional groups such as –OH and =C–H on AKB. Particularly, the existing of amorphous carbon and transition metal oxides, such as Fe2O3 and Mn5O8, could be beneficial for the photodegradation of MB for AKB. Meanwhile, experimental data indicated that adsorption kinetics complied with the pseudo-second order model well, and all of the tests had satisfactory results in terms of the highly efficient adsorption and photodegradation activity of AKB nanomaterials, which suggested its great potential in wastewater treatment.

TBE in Sweden

2020 ◽  
Keyword(s):  
Genetic Characterization ◽  
Immunoglobulin M ◽  
Enzyme Linked Immunosorbent Assay ◽  
Second Phase ◽  
Serum Samples ◽  
Tick Borne Encephalitis ◽  
Specific Immunoglobulin ◽  
Tick Borne Encephalitis Virus ◽  
First Time

Tick-borne encephalitis virus (TBEV) was isolated for the first time in Sweden in 1958 (from ticks and from 1 tick-borne encephalitis [TBE] patient).1 In 2003, Haglund and colleagues reported the isolation and antigenic and genetic characterization of 14 TBEV strains from Swedish patients (samples collected 1991–1994).2 The first serum sample, from which TBEV was isolated, was obtained 2–10 days after onset of disease and found to be negative for anti-TBEV immunoglobulin M (IgM) by enzyme-linked immunosorbent assay (ELISA), whereas TBEV-specific IgM (and TBEV-specific immunoglobulin G/cerebrospinal fluid [IgG/CSF] activity) was demonstrated in later serum samples taken during the second phase of the disease.

Chemical Constituents and Antibacterial Activity of Cissus Aralioides.

2020 ◽  
Vol 17 ◽  
Author(s):  
Balogun Olaoye Solomon ◽  
Ajayi Olukayode Solomon ◽  
Owolabi Temitayo Abidemi ◽  
Oladimeji Abdulkarbir Oladele ◽  
Liu Zhiqiang
Keyword(s):  
Plant Extract ◽  
Chemical Constituents ◽  
Ethyl Acetate Fraction ◽  
Antibacterial Activities ◽  
Sub Saharan Africa ◽  
Chromatographic Purification ◽  
Whole Plant ◽  
Sub Saharan ◽  
First Time

: Cissus aralioides is a medicinal plant used in sub-Saharan Africa for treatment of infectious diseases; however the chemical constituents of the plant have not been investigated. Thus, in this study, attempt was made at identifying predominant phytochemical constituents of the plant through chromatographic purification and silylation of the plant extract, and subsequent characterization using spectroscopic and GC-MS techniques. The minimum inhibitory concentration (MICs) for the antibacterial activities of the plant extract, chromatographic fractions and isolated compounds were also examined. Chromatographic purification of the ethyl acetate fraction from the whole plant afforded three compounds: β-sitosterol (1), stigmasterol (2) and friedelin (3). The phytosterols (1 and 2) were obtained together as a mixture. The GC-MS analysis of silylated extract indicated alcohols, fatty acids and sugars as predominant classes, with composition of 24.62, 36.90 and 26.52% respectively. Results of MICs indicated that friedelin and other chromatographic fractions had values (0.0626-1.0 mg/mL) comparable with the standard antibiotics used. Characterization of natural products from C. aralioides is being reported for the first time in this study.

Green Synthesis and Spectroscopic Studies of Ag-rGO Nanocomposites for Highly Selective Mercury (II) Sensing

2018 ◽  
Vol 9 (1) ◽  
pp. 101-108 ◽  
Author(s):  
Shubhangi J. Mane-Gavade ◽  
Sandip R. Sabale ◽  
Xiao-Ying Yu ◽  
Gurunath H. Nikam ◽  
Bhaskar V. Tamhankar
Keyword(s):  
Green Synthesis ◽  
Color Change ◽  
Limit Of Detection ◽  
Aqueous Media ◽  
Suitable Condition ◽  
Cost Effective ◽  
Spectroscopic Studies ◽  
Calibration Plot ◽  
First Time

Introduction: Herein we report the green synthesis and characterization of silverreduced graphene oxide nanocomposites (Ag-rGO) using Acacia nilotica gum for the first time. Experimental: We demonstrate the Hg2+ ions sensing ability of the Ag-rGO nanocomposites form aqueous medium. The developed colorimetric sensor method is simple, fast and selective for the detection of Hg2+ ions in aqueous media in presence of other associated ions. A significant color change was noticed with naked eye upon Hg2+ addition. The color change was not observed for cations including Sr2+, Ni2+, Cd2+, Pb2+, Mg2+, Ca2+, Fe2+, Ba2+ and Mn2+indicating that only Hg2+ shows a strong interaction with Ag-rGO nanocomposites. Under the most suitable condition, the calibration plot (A0-A) against concentration of Hg2+ was linear in the range of 0.1-1.0 ppm with a correlation coefficient (R2) value 0.9998. Results & Conclusion The concentration of Hg2+ was quantitatively determined with the Limit of Detection (LOD) of 0.85 ppm. Also, this method shows excellent selectivity towards Hg2+ over nine other cations tested. Moreover, the method offers a new cost effective, rapid and simple approach for the detection of Hg2+ in water samples.

scholarly journals Waste-Based One-Part Alkali Activated Materials

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2911
Author(s):  
Margarida Gonçalves ◽  
Inês Silveirinha Vilarinho ◽  
Marinélia Capela ◽  
Ana Caetano ◽  
Rui Miguel Novais ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Microstructural Analysis ◽  
Construction Materials ◽  
Sodium Metasilicate ◽  
High Compressive Strength ◽  
Hardened State ◽  
First Time ◽  
Furnace Slag ◽  
Alkali Activated

Ordinary Portland Cement is the most widely used binder in the construction sector; however, a very high carbon footprint is associated with its production process. Consequently, more sustainable alternative construction materials are being investigated, namely, one-part alkali activated materials (AAMs). In this work, waste-based one-part AAMs binders were developed using only a blast furnace slag, as the solid precursor, and sodium metasilicate, as the solid activator. For the first time, mortars in which the commercial sand was replaced by two exhausted sands from biomass boilers (CA and CT) were developed. Firstly, the characterization of the slag and sands (aggregates) was performed. After, the AAMs fresh and hardened state properties were evaluated, being the characterization complemented by FTIR and microstructural analysis. The binder and the mortars prepared with commercial sand presented high compressive strength values after 28 days of curing-56 MPa and 79 MPa, respectively. The mortars developed with exhausted sands exhibit outstanding compressive strength values, 86 and 70 MPa for CT and CA, respectively, and the other material’s properties were not affected. Consequently, this work proved that high compressive strength waste-based one-part AAMs mortars can be produced and that it is feasible to use another waste as aggregate in the mortar’s formulations: the exhausted sands from biomass boilers.

scholarly journals Cobalt-based magnetic Weyl semimetals with high-thermodynamic stabilities

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Wei Luo ◽  
Yuma Nakamura ◽  
Jinseon Park ◽  
Mina Yoon
Keyword(s):  
Tight Binding ◽  
Three Dimensional ◽  
Interlayer Coupling ◽  
First Principles Calculation ◽  
Optimization Approach ◽  
Binding Model ◽  
Nodal Lines ◽  
Weyl Semimetal ◽  
Topological Quantum ◽  
First Time

AbstractRecent experiments identified Co3Sn2S2 as the first magnetic Weyl semimetal (MWSM). Using first-principles calculation with a global optimization approach, we explore the structural stabilities and topological electronic properties of cobalt (Co)-based shandite and alloys, Co3MM’X2 (M/M’ = Ge, Sn, Pb, X = S, Se, Te), and identify stable structures with different Weyl phases. Using a tight-binding model, for the first time, we reveal that the physical origin of the nodal lines of a Co-based shandite structure is the interlayer coupling between Co atoms in different Kagome layers, while the number of Weyl points and their types are mainly governed by the interaction between Co and the metal atoms, Sn, Ge, and Pb. The Co3SnPbS2 alloy exhibits two distinguished topological phases, depending on the relative positions of the Sn and Pb atoms: a three-dimensional quantum anomalous Hall metal, and a MWSM phase with anomalous Hall conductivity (~1290 Ω−1 cm−1) that is larger than that of Co2Sn2S2. Our work reveals the physical mechanism of the origination of Weyl fermions in Co-based shandite structures and proposes topological quantum states with high thermal stability.

scholarly journals Isolation and characterization of a new cold-active protease from psychrotrophic bacteria of Western Himalayan glacial soil

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Saleem Farooq ◽  
Ruqeya Nazir ◽  
Shabir Ahmad Ganai ◽  
Bashir Ahmad Ganai
Keyword(s):  
Specific Activity ◽  
Temperature Range ◽  
Psychrotrophic Bacteria ◽  
Isolation And Characterization ◽  
Cold Active ◽  
Active Protease ◽  
Quantitative Screening ◽  
First Time ◽  
Low K

AbstractAs an approach to the exploration of cold-active enzymes, in this study, we isolated a cold-active protease produced by psychrotrophic bacteria from glacial soils of Thajwas Glacier, Himalayas. The isolated strain BO1, identified as Bacillus pumilus, grew well within a temperature range of 4–30 °C. After its qualitative and quantitative screening, the cold-active protease (Apr-BO1) was purified. The Apr-BO1 had a molecular mass of 38 kDa and showed maximum (37.02 U/mg) specific activity at 20 °C, with casein as substrate. It was stable and active between the temperature range of 5–35 °C and pH 6.0–12.0, with an optimum temperature of 20 °C at pH 9.0. The Apr-BO1 had low Km value of 1.0 mg/ml and Vmax 10.0 µmol/ml/min. Moreover, it displayed better tolerance to organic solvents, surfactants, metal ions and reducing agents than most alkaline proteases. The results exhibited that it effectively removed the stains even in a cold wash and could be considered a decent detergent additive. Furthermore, through protein modelling, the structure of this protease was generated from template, subtilisin E of Bacillus subtilis (PDB ID: 3WHI), and different methods checked its quality. For the first time, this study reported the protein sequence for psychrotrophic Apr-BO1 and brought forth its novelty among other cold-active proteases.

Optimization and characterization of flavonoids extracted from Cannabis sativa fibers

2021 ◽  
pp. 004051752110277
Author(s):  
Qilu Cui ◽  
Jiawei Li ◽  
Chongwen Yu
Keyword(s):  
Chemical Structure ◽  
Cannabis Sativa ◽  
Ethanol Concentration ◽  
Extraction Process ◽  
Test Results ◽  
Hemp Fiber ◽  
Hemp Fibers ◽  
Structure Surface ◽  
Degumming Process

In this paper, the extraction process of flavonoids from hemp fibers was studied. Response surface methodology (RSM) analysis of the extraction parameters indicated that optimized results would be ethanol concentration 76 vol.%, bath ratio 1:50, and reaction time 139 min; therefore, an optimal extraction rate of flavonoids of 0.2275% can be obtained. The chemical structure, surface morphology and element composition of flavonoid extracts were analyzed. The test results indicated that hemp extract contains flavonoids, which can be used to extract flavonoids from hemp fiber, so as to comprehensively develop hemp fiber and reduce the discharge of waste liquid in the traditional degumming process.

scholarly journals Synthesis and Characterization of Exopolysaccharide Encapsulated PCL/Gelatin Skin Substitute for Full-Thickness Wound Regeneration

Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 854
Author(s):  
Ahmad Hivechi ◽  
Peiman Brouki Milan ◽  
Khashayar Modabberi ◽  
Moein Amoupour ◽  
Kaveh Ebrahimzadeh ◽  
...  
Keyword(s):  
Cell Activity ◽  
Average Diameter ◽  
Skin Substitute ◽  
Full Thickness ◽  
Skin Integrity ◽  
Hematoxylin And Eosin ◽  
First Time ◽  
Full Thickness Wound

Loss of skin integrity can lead to serious problems and even death. In this study, for the first time, the effect of exopolysaccharide (EPS) produced by cold-adapted yeast R. mucilaginosa sp. GUMS16 on a full-thickness wound in rats was evaluated. The GUMS16 strain’s EPS was precipitated by adding cold ethanol and then lyophilized. Afterward, the EPS with polycaprolactone (PCL) and gelatin was fabricated into nanofibers with two single-needle and double-needle procedures. The rats’ full-thickness wounds were treated with nanofibers and Hematoxylin and eosin (H&E) and Masson’s Trichrome staining was done for studying the wound healing in rats. Obtained results from SEM, DLS, FTIR, and TGA showed that EPS has a carbohydrate chemical structure with an average diameter of 40 nm. Cell viability assessments showed that the 2% EPS loaded sample exhibits the highest cell activity. Moreover, in vivo implantation of nanofiber webs on the full-thickness wound on rat models displayed a faster healing rate when EPS was loaded into a nanofiber. These results suggest that the produced EPS can be used for skin tissue engineering applications.

Sign in / Sign up

Export Citation Format

Share Document