Improving the Performance of a Piezoelectric Energy Harvester Using a Tip Spring-Mass System

2012 ◽  
Author(s):  
Yang Zhu ◽  
Oumar Barry ◽  
Weijiun Su ◽  
Jean Zu
Keyword(s):  
Resonance Frequency ◽  
Piezoelectric Materials ◽  
Low Frequency ◽  
Ambient Vibration ◽  
Mass System ◽  
Resonant Frequencies ◽  
Energy Harvesters ◽  
The Past ◽  
Piezoelectric Energy

Vibration-based energy harvesting using piezoelectric materials has gained considerable attention over the past decade. Currently, most piezoelectric energy harvesters (PEHs) are single resonance frequency based. The performance of a single-resonance PEH is often limited to only one resonance frequency. This paper discusses the possibility of improving the performance of a bimorph PEH by tuning the PEH using a spring-mass system attached to the bimorph’s free end. Through adding the spring-mass system, the PEH’s resonance frequency can be tuned to match the ambient vibration frequency, and its voltage/power-generating capability can be improved. An electromechanical model of the PEH is derived based on the Lagrange multiplier method. The model is then used in a harmonic base excitation case study, and the coupled electromechanical outputs are discussed. Simulation results show that the spring-mass attachment can create two resonant frequencies, making the PEH capable of working efficiently at two different frequencies in a low-frequency level. It is also shown that by properly selecting the spring stiffness and the mass, the voltage and power output of the PEH can be greatly increased as compared to a single bimorph without the spring-mass system.

Design, Analysis, and Experimental Studies of a Novel PVDF-Based Piezoelectric Energy Harvester With Beating Mechanisms

2014 ◽  
Author(s):  
Kuo-Shen Chen
Keyword(s):  
Natural Frequency ◽  
Energy Harvester ◽  
Piezoelectric Materials ◽  
Low Frequency ◽  
Major Barrier ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Low Frequency Vibration ◽  
High Efficient ◽  
The Future

Wireless sensor networks become increasingly important in modern life for structural health monitoring and other related applications. In these applications, due to their overall sensor populations and possible covered measurement areas, the replacement of batteries becomes a difficult and unrealistic task. As a result, energy harvesters to convert environment wasted vibration energy into electricity for powering those sensor nodes become important and many miniaturized device have been realized by using MEMS technology. In order to achieve optimal performance, the energy harvester must be operated at the resonance frequency. However, the vibration frequencies of environmental vibrations are usually much less than that of those miniaturizing energy harvesters and this fact could be a major barrier for energy harvesting performance. In this paper, a new piezoelectric energy scavenging concept is proposed and demonstrated to convert environmental vibrations into electricity. Unlike previous MEMS-based piezoelectric energy harvesters, which suffer from matching between environmental low frequency vibration and the much higher system natural frequency, this work proposes a novel beating design using polymer piezoelectric materials in collaborating with a beating mechanism. That is, by creating impact force via the low frequency vibration motion from the mechanism, it is possible to excite system natural frequency by the low frequency environmental vibrations and it is possible to operate the entire system at the natural frequency. This work contains details in presenting this idea, designing piezoelectric harvester systems with flexible PVDF elements, exploring their vibration characteristics, and energy accumulating strategies by using a capacitor with a full-bridged rectifiers or a boost conversion. By experimental characterization, the overall harvesting efficiency of the proposed design is much greater than that from the design without the beating mechanism. It indicates that the efficiency is significantly improved and the proposed translational design could potentially improve the future design approach for piezoelectric energy harvesters significantly. In summary, this preliminary study shows that it is a feasible scheme for the application of piezoelectric materials in harvesting electricity from environmental vibrations. Although this work is still in its initial phase, the results and conclusions of this work are still invaluable for guiding the development of high efficient piezoelectric harvesters in the future.

Comparative Analysis of One-Dimensional and Two-Dimensional Cantilever Piezoelectric Energy Harvesters

2014 ◽  
Vol 1 (3-4) ◽  
Author(s):  
Nathan Sharpes ◽  
Abdessattar Abdelkefi ◽  
Shashank Priya
Keyword(s):  
Comparative Analysis ◽  
Excitation Frequency ◽  
Low Frequency ◽  
Ambient Vibration ◽  
Two Dimensional ◽  
One Dimensional ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Resonance Frequencies ◽  
Tip Mass

AbstractA long-standing encumbrance in the design of low-frequency energy harvesters has been the need of substantial beam length and/or large tip mass values to reach the low resonance frequencies where significant energy can be harvested from the ambient vibration sources. This need of large length and tip mass may result in a device that is too large to be practical. The zigzag (meandering) beam structure has emerged as a solution to this problem. In this letter, we provide comparative analysis between the classical one-dimensional cantilever bimorph and the two-dimensional zigzag unimorph piezoelectric energy harvesters. The results demonstrate that depending upon the excitation frequency, the zigzag harvester is significantly better in terms of magnitude of natural frequency, harvested power, and power density, compared to the cantilever configuration. The dimensions were chosen for each design such that the zigzag structure would have 25.4×25.4 mm

scholarly journals A Multi-Mode Broadband Vibration Energy Harvester Composed of Symmetrically Distributed U-Shaped Cantilever Beams

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 203
Author(s):  
Xiaohua Huang ◽  
Cheng Zhang ◽  
Keren Dai
Keyword(s):  
Energy Harvester ◽  
Low Frequency ◽  
Experimental Results ◽  
Vibration Energy ◽  
Cantilever Beams ◽  
Resonant Frequencies ◽  
Promising Alternative ◽  
Piezoelectric Energy ◽  
Straight Beam ◽  
Resonance Frequencies

Using the piezoelectric effect to harvest energy from surrounding vibrations is a promising alternative solution for powering small electronic devices such as wireless sensors and portable devices. A conventional piezoelectric energy harvester (PEH) can only efficiently collect energy within a small range around the resonance frequency. To realize broadband vibration energy harvesting, the idea of multiple-degrees-of-freedom (DOF) PEH to realize multiple resonant frequencies within a certain range has been recently proposed and some preliminary research has validated its feasibility. Therefore, this paper proposed a multi-DOF wideband PEH based on the frequency interval shortening mechanism to realize five resonance frequencies close enough to each other. The PEH consists of five tip masses, two U-shaped cantilever beams and a straight beam, and tuning of the resonance frequencies is realized by specific parameter design. The electrical characteristics of the PEH are analyzed by simulation and experiment, validating that the PEH can effectively expand the operating bandwidth and collect vibration energy in the low frequency. Experimental results show that the PEH has five low-frequency resonant frequencies, which are 13, 15, 18, 21 and 24 Hz; under the action of 0.5 g acceleration, the maximum output power is 52.2, 49.4, 61.3, 39.2 and 32.1 μW, respectively. In view of the difference between the simulation and the experimental results, this paper conducted an error analysis and revealed that the material parameters and parasitic capacitance are important factors that affect the simulation results. Based on the analysis, the simulation is improved for better agreement with experiments.

scholarly journals Load Resistance Optimization of a Broadband Bistable Piezoelectric Energy Harvester for Primary Harmonic and Subharmonic Behaviors

2021 ◽  
Vol 13 (5) ◽  
pp. 2865 ◽  
Author(s):  
Sungryong Bae ◽  
Pilkee Kim
Keyword(s):  
Energy Harvester ◽  
Load Resistance ◽  
Oscillation Period ◽  
Ambient Vibration ◽  
Ambient Vibrations ◽  
Frequency Dependency ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Bistable Energy Harvester

In this study, optimization of the external load resistance of a piezoelectric bistable energy harvester was performed for primary harmonic (period-1T) and subharmonic (period-3T) interwell motions. The analytical expression of the optimal load resistance was derived, based on the spectral analyses of the interwell motions, and evaluated. The analytical results are in excellent agreement with the numerical ones. A parametric study shows that the optimal load resistance depended on the forcing frequency, but not the intensity of the ambient vibration. Additionally, it was found that the optimal resistance for the period-3T interwell motion tended to be approximately three times larger than that for the period-1T interwell motion, which means that the optimal resistance was directly affected by the oscillation frequency (or oscillation period) of the motion rather than the forcing frequency. For broadband energy harvesting applications, the subharmonic interwell motion is also useful, in addition to the primary harmonic interwell motion. In designing such piezoelectric bistable energy harvesters, the frequency dependency of the optimal load resistance should be considered properly depending on ambient vibrations.

Multimodal pizza-shaped piezoelectric vibration-based energy harvesters

2021 ◽  
pp. 1045389X2110069
Author(s):  
Virgilio J Caetano ◽  
Marcelo A Savi
Keyword(s):  
Energy Harvesting ◽  
Frequency Spectrum ◽  
Optimization Procedure ◽  
Single Mode ◽  
Ambient Vibration ◽  
Vibration Source ◽  
Element Analysis ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Harvesting Systems

Energy harvesting from ambient vibration through piezoelectric devices has received a lot of attention in recent years from both academia and industry. One of the main challenges is to develop devices capable of adapting to diverse sources of environmental excitation, being able to efficiently operate over a broadband frequency spectrum. This work proposes a novel multimodal design of a piezoelectric energy harvesting system to harness energy from a wideband ambient vibration source. Circular-shaped and pizza-shaped designs are employed as candidates for the device, comparing their performance with classical beam-shaped devices. Finite element analysis is employed to model system dynamics using ANSYS Workbench. An optimization procedure is applied to the system aiming to seek a configuration that can extract energy from a broader frequency spectrum and maximize its output power. A comparative analysis with conventional energy harvesting systems is performed. Numerical simulations are carried out to investigate the harvester performances under harmonic and random excitations. Results show that the proposed multimodal harvester has potential to harness energy from broadband ambient vibration sources presenting performance advantages in comparison to conventional single-mode energy harvesters.

scholarly journals Piezoelectric Energy Generators Based on Spring and Inertial Mass

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2163 ◽  
Author(s):  
Sanghyun Yoon ◽  
Jinhwan Kim ◽  
Kyung-Ho Cho ◽  
Young-Ho Ko ◽  
Sang-Kwon Lee ◽  
...  
Keyword(s):  
Piezoelectric Materials ◽  
Electric Energy ◽  
Inertial Mass ◽  
Design Parameters ◽  
Mechanical Shock ◽  
Generator System ◽  
Energy Harvesters ◽  
Shock Energy ◽  
Piezoelectric Energy ◽  
And Performance

In this study, inertial mass-based piezoelectric energy generators with and without a spring were designed and tested. This energy harvesting system is based on the shock absorber, which is widely used to protect humans or products from mechanical shock. Mechanical shock energies, which were applied to the energy absorber, were converted into electrical energies. To design the energy harvester, an inertial mass was introduced to focus the energy generating position. In addition, a spring was designed and tested to increase the energy generation time by absorbing the mechanical shock energy and releasing a decreased shock energy over a longer time. Both inertial mass and the spring are the key design parameters for energy harvesters as the piezoelectric materials, Pb(Mg1/3Nb2/3)O3-PbTiO3 piezoelectric ceramics were employed to store and convert the mechanical force into electric energy. In this research, we will discuss the design and performance of the energy generator system based on shock absorbers.

Wide Bandwidth Piezoelectric MEMS Energy Harvesting

2013 ◽  
Vol 1556 ◽  
Author(s):  
Ruize Xu ◽  
Sang-Gook Kim
Keyword(s):  
Structural Design ◽  
Microelectromechanical Systems ◽  
Piezoelectric Materials ◽  
Ambient Vibration ◽  
Wide Bandwidth ◽  
Frequency Spectra ◽  
Energy Harvesters ◽  
Reasonable Cost ◽  
Continuous Power ◽  
Near Future

ABSTRACTPiezoelectric Microelectromechanical Systems (MEMS) has been proven to be an attractive technology for harvesting small energy from the ambient vibration. Recent advancements in piezoelectric materials and harvester structural design, individually or in combination, have improved MEMS energy harvesters to achieve high enough power density, compactness and ultra wide bandwidth, bringing us closer towards battery-less autonomous sensors systems and networks in near future. Among the breakthroughs, non-linear resonating beam for wide bandwidth resonance is the key development to enable robust operation of MEMS energy harvesters over the unpredictable and uncontrollable frequency spectra of ambient vibration. We expect that a coin size harvester will be able to harvest about 100μW continuous power at below 100 Hz and less than 0.5 g input vibration and at reasonable cost.

Topology Optimization of Piezoelectric Energy Harvesting Devices Subjected to Stochastic Excitation

2010 ◽  
Author(s):  
Zheqi Lin ◽  
Hae Chang Gea ◽  
Shutian Liu
Keyword(s):  
Topology Optimization ◽  
Energy Harvesting ◽  
Electrical Energy ◽  
Ambient Vibration ◽  
Piezoelectric Energy Harvesting ◽  
The Past ◽  
Piezoelectric Energy ◽  
Random Responses ◽  
Pseudo Excitation ◽  
Energy Harvesting Devices

Converting ambient vibration energy into electrical energy using piezoelectric energy harvester has attracted much interest in the past decades. In this paper, topology optimization is applied to design the optimal layout of the piezoelectric energy harvesting devices. The objective function is defined as to maximize the energy harvesting performance over a range of ambient vibration frequencies. Pseudo excitation method (PEM) is applied to analyze structural stationary random responses. Sensitivity analysis is derived by the adjoint method. Numerical examples are presented to demonstrate the validity of the proposed approach.

Heartbeat Energy Harvesting Using the Fan-Folded Piezoelectric Beam Geometry

2015 ◽  
Author(s):  
M. H. Ansari ◽  
M. Amin Karami
Keyword(s):  
Natural Frequency ◽  
Energy Harvester ◽  
Low Frequency ◽  
Mode Shapes ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Mechanical Coupling ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam

A three dimensional piezoelectric vibration energy harvester is designed to generate electricity from heartbeat vibrations. The device consists of several bimorph piezoelectric beams stacked on top of each other. These horizontal bimorph beams are connected to each other by rigid vertical beams making a fan-folded geometry. One end of the design is clamped and the other end is free. One major problem in micro-scale piezoelectric energy harvesters is their high natural frequency. The same challenge is faced in development of a compact vibration energy harvester for the low frequency heartbeat vibrations. One way to decrease the natural frequency is to increase the length of the bimorph beam. This approach is not usually practical due to size limitations. By utilizing the fan-folded geometry, the natural frequency is decreased while the size constraints are observed. The required size limit of the energy harvester is 1 cm by 1 cm by 1 cm. In this paper, the natural frequencies and mode shapes of fan-folded energy harvesters are analytically derived. The electro-mechanical coupling has been included in the model for the piezoelectric beam. The design criteria for the device are discussed.

A Novel Multi-Directional Nonlinear Piezoelectric Energy Harvester Coupled With Nonlinear Conditioning Circuits

2015 ◽  
Author(s):  
Zhengbao Yang ◽  
Jean Zu
Keyword(s):  
Energy Harvester ◽  
Piezoelectric Materials ◽  
Electrical Energy ◽  
Elastic Rods ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
High Power Output ◽  
Transduction Mechanisms ◽  
Self Powered ◽  
Aluminum Plates

Energy harvesting from vibrations has become, in recent years, a recurring target of a quantity of research to achieve self-powered operation of low-power electronic devices. However, most of energy harvesters developed to date, regardless of different transduction mechanisms and various structures, are designed to capture vibration energy from single predetermined direction. To overcome the problem of the unidirectional sensitivity, we proposed a novel multi-directional nonlinear energy harvester using piezoelectric materials. The harvester consists of a flexural center (one PZT plate sandwiched by two bow-shaped aluminum plates) and a pair of elastic rods. Base vibration is amplified and transferred to the flexural center by the elastic rods and then converted to electrical energy via the piezoelectric effect. A prototype was fabricated and experimentally compared with traditional cantilevered piezoelectric energy harvester. Following that, a nonlinear conditioning circuit (self-powered SSHI) was analyzed and adopted to improve the performance. Experimental results shows that the proposed energy harvester has the capability of generating power constantly when the excitation direction is changed in 360. It also exhibits a wide frequency bandwidth and a high power output which is further improved by the nonlinear circuit.

Sign in / Sign up

Export Citation Format

Share Document