Design and Experiment of a Concentrating Transpired Air Heating System

Author(s):  
N. Shams ◽  
M. Mc Keever ◽  
S. Mc Cormack ◽  
B. Norton

This paper presents the physical design and experiments of the Concentrating Transpired Air Heating (CTAH) system as a combination of subsystems of parabolic primary and circular secondary reflector that concentrates incident solar radiation onto an inverted perforated absorber. Optical efficiency of the CTAH system has been analysed using a 2D ray tracing model. Experiments have been carried out for 50% perforated black painted aluminium inverted absorber for glazed and unglazed systems. Results show a significant temperature rise of the absorber surface in both cases. The maximum temperature of the absorber for the unglazed system is 52.1°C at 22.5°C ambient temperature, where as for the covered system, it is 67.9°C at 23.2°C ambient temperature.

2021 ◽  
Author(s):  
Gonzalo Martín Rivelli ◽  
María Elena Fernández Long ◽  
Leonor Gabriela Abeledo ◽  
Daniel Calderini ◽  
Daniel Julio Miralles ◽  
...  

Abstract Episodes of heat stress constrain crop production and will be aggravated in the near future according to short and medium-term climate scenarios. Global increase in cloudiness has also been observed, decreasing the incident solar radiation. This work was aimed to quantify the probability of occurrence of heat stress and cloudiness, alone or combined, during the typical post-flowering period of wheat and canola in the Southern Cone of South America. Extended climate series (last 3-5 decades with daily register) of 33 conventional weather stations from Argentina, Brazil, Chile and Uruguay (23ºS to 40ºS) were analysed considering the period from September to December. Two different daily events of heat stress were determined: i) maximum daily temperature above 30ºC (T>30ºC), and ii) 5ºC above the historical average maximum temperature of that day (T+5ºC). A cloudiness event was defined in our work as incident solar radiation 50% lower than the historical average radiation of that day (R50%). The T>30ºC event increased its probability of occurrence throughout the post-flowering phase, from September to December. By contrast, the risk of T+5ºC event decreased slightly, just like for R50%, and the higher the latitude, the lower the probability of R50%. The T>30ºC plus R50% combined stresses reached greater cumulated probabilities during post-flowering, compared to T+5ºC plus R50%, being 42% vs. 15% in northernmost locations, 26% vs. 19% in central (between 31ºS to 35ºS), and 28% vs. 1% in southernmost locations, respectively. A curvilinear relationship emerged between the monthly probability of combined stresses and the number of days with stress per month. In summary, T>30ºC was the most frequent thermal stress during post-flowering in wheat and canola. Both combined stresses had a noticeable risk of occurrence, but T>30ºC plus R50% was the highest. Evidence of the recent past and current occurrence of heat stress individually, and its combination with cloudiness events during post-flowering of temperate crops, serves as a baseline for future climate scenarios in main cropped areas in the Southern Cone of South America.


2019 ◽  
Vol 142 (1) ◽  
Author(s):  
Dara Khalid Khidhir ◽  
Soorkeu A. Atrooshi

Abstract The principle of solar chimney power plant (SCPP) is based on harvesting the thermal spectrum of solar radiation and converting it to mechanical energy by the means of a collector, a wind turbine, and a chimney. In this work, a number of experiments were performed on a modified model made up of one-third of the circular collector area. Field data from selected clear, sunny days were recorded and studied. The analysis focused on time-temperature relations for ambient, near chimney entry point and the collector periphery, in addition to hourly solar radiation intensity and air velocity inside the chimney. The results show that for this geometry arrangement, the maximum temperature of the air entering the chimney is achieved before the ambient temperature reaches its peak value. Air velocity inside the chimney depends on the intensity of solar radiation and the temperature difference between the air temperature entering the chimney and the ambient temperature. Solar intensity directly affects the temperature of air beneath the collector, and a part of this energy is stored in the ground. Later, when the solar radiation is impaired, the stored energy can be utilized. Air velocity of 2.1 m/s is obtained after the solar noon, when the solar intensity is 737 W/m2 and the maximum temperature difference is 11.2 °C. Due to the unique geometrical shape of the rig, a minor temperature loss of up to 1.3 °C occurs for the air near the center of the chimney.


2014 ◽  
Vol 984-985 ◽  
pp. 800-806
Author(s):  
G. Jims John Wessley ◽  
P. Koshy Mathews

This paper presents the results of the experimental investigation on a solar flat plate collector carried out at Coimbatore, India (11°N Latitude and 74°E Longitude). The collector tubes allowed the water to flow twice across the flat plate collector using a circulating pump during which the water gets heated by the solar radiation received by the absorber. The maximum temperature of water obtained on a typical day in the month of April was 64°C with a solar radiation of 932.2651 W/m2. The available solar radiation strongly influences the temperature gain of the system while the wind velocity plays a considerable role in influencing the heat lost by the system. It is observed that the two-pass flow of water across the absorber plate results in a maximum temperature gain with an overall collector efficiency of 43.7 %. This solar water heating system using flat plate collector can be used for small-scale desalination applications.


2021 ◽  
Vol 10 (4) ◽  
pp. 687-697
Author(s):  
Moien A. Omar ◽  
Marwan M. Mahmoud

Correct matching between PV array and inverter improves the inverter efficiency, increases the annual produced energy, decreases the clipping losses of the inverter, and prevent to a large extent the inverter frequent shut downs during clear sunny days of high solar radiation and low ambient temperature. Therefore, this paper presents a new methodology for selecting the appropriate peak power of the PV array with respect to the inverter output AC rated power taking into account the local daily distribution of solar radiation and ambient temperature. In addition, the proposed methodology specifies the appropriate number of PV modules in each string and the number of parallel strings connected to the input of the inverteraccording to its specifications and to PV cell temperature. Mathematically modeling of system parameters and components are presented and used in the simulation to investigate the different scenarios. The paper presents also a case study using simulation to find the optimal matching parameters of a PV array connected to an inverter with the specifications: 6 kW rated output power, an input mpp voltage range of 333-500 V, 6.2 kW maximum input DC power, and an output AC voltage of 230 Vrms. Considering the local climate conditions in West Bank, the simulation resulted a peak power of 7 kW for the PV array, which is greater than the inverter output power by the factor 1.16. In addition, the obtained PV array consists of two parallel strings each includes 12 PV modules  connected in series  while each PV module is rated at 290 W. The output voltage of the PV arrayvaries between 359 V to 564 Vat minimum and maximum temperature of 10 ˚C to 70 ˚C respectively. This PV array-inverter combination resulted by simulation an annual yield of 1600 kWh/kWp and an energy of 11197 kWh which corresponds to an energy gain of 1591 kWh/year more than using a PV array with a peak power of 6 kW as the inverter rated power.


Author(s):  
Zairul Azrul Zakaria ◽  
Zafri Azran Abdul Majid ◽  
Muhammad Amin Harun ◽  
Ahmad Faris Ismail ◽  
Sany Izan Ihsan ◽  
...  

Existing design of Heat-Pipe Evacuated Tube Collector (HP ETC) for solar water heating require storage tank and additional heat exchanger required for air heating application which leads to the extra spacing and costing requirement. HP ETC have better thermal performance to produce high outlet temperature than flat plate collector (FPC), especially during diffuse solar radiation. But HP ETC normally focusing on water heating system. Furthermore, HP ETC and FPC installation need to be positioned either to south or north facing to ensure the solar thermal collector absorbs more solar radiation. Meanwhile, HP ETC need to be tilt at the correct angle to maximize the performance of the system. These could lead to design limitation. The aim of this research is to develop the new design of Evacuated Glass-Thermal Absorber Tube Collector namely EGATC for drying application. It was developed from conventional HP ETC evacuated glass tube. In this study comparison result of EGATC and HP ETC performance were evaluated. The three days outdoor experiment proves that the performance of EGATC was better than HP ETC in air heating application which is provide higher outlet temperature. Based on the result, EGATC (Day 1: 50.9 oC, Day 2: 53.9 oC, Day 3: 49.2 oC) performed better with slightly higher temperature at outlet temperature compare with HP ETC (Day 1: 46.7 oC, Day 2: 50.3 oC, Day 3: 46.9 oC). It is concluded that EGATC have better performance in term of temperature different and outlet temperature as compared to HP ETC. EGATC (Day 1: 53.6%, Day 2: 50.6%, Day 3: 49.8%) also have greater efficiency in term of heat storage capability as compared to HP ETC (Day 1: 42.7%, Day 2: 41.6%, Day 3: 41.1%). Regarding energy buffer storage, EGATC have better energy storage compared to HP ETC at sudden weather change such as diffuse solar radiation during clouds. The outlet temperature of EGATC (42.3 oC) was remained slightly higher compared to HP ETC (39.9 oC) at the beginning. The outlet temperature gradually drops slower during discharging period until the end of the experiment for 15 minutes towards outlet temperature 41.1ºC and 37.2ºC for both EGATC and HP ETC with temperature difference 1.2ºC and 2.7ºC respectively.


Author(s):  
Vijayakumar Rajendran ◽  
Harichandran Ramasubbu ◽  
Karthick Alagar ◽  
Vignesh Kumar Ramalingam

An experimental study has been carried out to enhance a solar air heater’s performance by integrating artificial roughness through baffles on the absorber plate. In this paper, the thermal and energy matrices analysis of a Solar Air Heater (SAH) roughened with V up perforated baffles have been investigated. The effect of various mass flow rates on the SAH was analyzed with and without baffles. Experimental outputs like outlet air temperature, useful energy (heat) gain and thermal efficiency were evaluated to confirm the performance improvement. The baffled absorber plate SAH was found to give the maximum thermal efficiency and useful energy gain of 89.3% and 1321.37 W at a mass flow rate of 0.0346 kg/s, 13% and 12% higher than SAH without baffle. This result showed that the V up-shaped ribs in flow arrangement provide better thermal performance than smooth plate SAH for the parameter investigated. Energy matrices analysis and carbon dioxide mitigation of the SAH system were also analyzed.


Fluids ◽  
2021 ◽  
Vol 6 (8) ◽  
pp. 275
Author(s):  
Ahmed J. Hamad

One essential utilization of phase change materials as energy storage materials is energy saving and temperature control in air conditioning and indirect solar air drying systems. This study presents an experimental investigation evaluating the characteristics and energy savings of multiple phase change materials subjected to internal flow in an air heating system during charging and discharging cycles. The experimental tests were conducted using a test rig consisting of two main parts, an air supply duct and a room model equipped with phase change materials (PCMs) placed in rectangular aluminum panels. Analysis of the results was based on three test cases: PCM1 (Paraffin wax) placed in the air duct was used alone in the first case; PCM2 (RT–42) placed in the room model was used alone in the second case; and in the third case, the two PCMs (PCM1 and PCM2) were used at the same time. The results revealed a significant improvement in the energy savings and room model temperature control for the air heating system incorporated with multiple PCMs compared with that of a single PCM. Complete melting during the charging cycle occurred at temperatures in the range of 57–60 °C for PCM1 and 38–43 °C for PCM2, respectively, thereby validating the reported PCMs’ melting–solidification results. Multiple PCMs maintained the room air temperature at the desired range of 35–45.2 °C in the air heating applications by minimizing the air temperature fluctuations. The augmentation in discharging time and improvement in the room model temperature using multiple PCMs were about 28.4% higher than those without the use of PCMs. The total energy saving using two PCMs was higher by about 29.5% and 46.7% compared with the use of PCM1 and PCM2, respectively. It can be concluded that multiple PCMs have revealed higher energy savings and thermal stability for the air heating system considered in the current study.


Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 802
Author(s):  
Kristian Skeie ◽  
Arild Gustavsen

In building thermal energy characterisation, the relevance of proper modelling of the effects caused by solar radiation, temperature and wind is seen as a critical factor. Open geospatial datasets are growing in diversity, easing access to meteorological data and other relevant information that can be used for building energy modelling. However, the application of geospatial techniques combining multiple open datasets is not yet common in the often scripted workflows of data-driven building thermal performance characterisation. We present a method for processing time-series from climate reanalysis and satellite-derived solar irradiance services, by implementing land-use, and elevation raster maps served in an elevation profile web-service. The article describes a methodology to: (1) adapt gridded weather data to four case-building sites in Europe; (2) calculate the incident solar radiation on the building facades; (3) estimate wind and temperature-dependent infiltration using a single-zone infiltration model and (4) including separating and evaluating the sheltering effect of buildings and trees in the vicinity, based on building footprints. Calculations of solar radiation, surface wind and air infiltration potential are done using validated models published in the scientific literature. We found that using scripting tools to automate geoprocessing tasks is widespread, and implementing such techniques in conjunction with an elevation profile web service made it possible to utilise information from open geospatial data surrounding a building site effectively. We expect that the modelling approach could be further improved, including diffuse-shading methods and evaluating other wind shelter methods for urban settings.


2011 ◽  
Vol 71-78 ◽  
pp. 2073-2076
Author(s):  
Fen E Hu ◽  
Zhi Juan Wang

A solar air drying system including solar air collector, drying cabinet and air blower for notoginseng drying has been constructed and tested. Two identical air solar collectors with two air channels, V-groove absorption heat plates and a single glass cover have been employed. The results of test show that the solar air collectors can obtain a good thermal performance in winter season. When the air flow mass rate is fixed at 0.0597kg·s-1, the maximum values of thermal efficiency and outlet air temperature are 76.0% and 62.2°C, respectively. The experimental analysis between two sampling notoginseng drying suggests that the solar drying is very effective, and the drying time has been shorten to about 440 minutes from 990 minutes of the traditional drying by sun. It is also observed that using the solar drying system notoginseng has a higher quality than traditional drying method.


2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Prem Sagar Naik ◽  
Arun Palatel

A photovoltaic-thermal water heating system is a hybrid energy conversion device transforming the incident solar radiation to yield electrical energy and thermal energy. Plane reflectors are found to be a convenient option for enhancing the solar radiation incident on the collector plane. The present work investigates the performance of a photovoltaic-thermal water heater integrated with a plane reflector mounted on the top edge of the collector for the tropical climate of Calicut (11.25°N, 75.78°E). Performance testing of the system has been carried out for the winter season of the location. The variations in thermal and electrical output are studied for various inclination angles of the reflector. The system performance is evaluated on the basis of system energy efficiency and exergetic efficiency. It is observed that there is a significant enhancement in the thermal and electrical output of the system with the integration of the reflector as compared to the system without the reflector. For the present system, the reflector tilt angle in the range of 85–100° has been found to be suitable in terms of enhanced system output and exergetic efficiency for the winter conditions of Calicut.


Sign in / Sign up

Export Citation Format

Share Document