Study on Overall Design of a Vertical Take-Off and Landing Unmanned Aerial Vehicle Powered by Electric Ducted Fans

2021 ◽  
Author(s):  
Tawei Chou ◽  
Qiyu Ying ◽  
Yuping Qian ◽  
Weilin Zhuge ◽  
Yangjun Zhang
Keyword(s):  
Power Unit ◽  
Unmanned Aerial Vehicle ◽  
Cfd Simulation ◽  
Design Method ◽  
Load Capacity ◽  
Design Procedure ◽  
Low Noise ◽  
Overall Design ◽  
Ducted Fan ◽  
Aerial Vehicle

Abstract Facing the growing traffic fleet in the cities nowadays, it is believed that three-dimensional urban transportation could be a solution and will be introduced in the near future. Vertical take-off and landing flying platforms powered by ducted fans will attract increasingly attention because it has advantages on high propulsion efficiency, low noise, and better safety. However, unlike traditional open-blade multi-rotor drones, ducted fan drones lack a systematic design approach that comprehensively considers the overall system performance and the power unit efficiency. Current design procedure leads to insufficient load capacity and low efficiency systems. This paper proposes an overall design method for a ducted fan-type vertical take-off and landing flight platform. The ducted fan and motor of the core power unit are designed and selected aiming at improving aerodynamic efficiency and structural utilization of the system. A heavy-load vertical take-off and landing Unmanned Aerial Vehicle (UAV) powered by ducted fans with a take-off weight of 450kg is designed based on this method. CFD simulation is utilized to calculate the performance of the designed Unmanned Aerial Vehicle, and finite element analysis is carried out to examine the overall strength safety. The final design results show that the overall design method plays a great role in the development of ducted fan UAV.

INTEGRATED PID CONTROLLER DESIGN FOR AN UNMANNED AERIAL VEHICLE WITH STATIC STABILITY

2013 ◽  
Vol 54 (3) ◽  
pp. 200-215 ◽  
Author(s):  
R. LI ◽  
Y. J. SHI ◽  
H. L. XU
Keyword(s):  
Fuzzy Control ◽  
Unmanned Aerial Vehicle ◽  
Pid Controller ◽  
Control Method ◽  
Controller Design ◽  
Design Method ◽  
Design Procedure ◽  
Static Stability ◽  
Aerial Vehicle ◽  
Rolling Mode

AbstractThis paper presents an integrated guidance and control (IGC) design method for an unmanned aerial vehicle with static stability which is described by a nonlinear six-degree-of-freedom (6-DOF) model. The model is linearized by using small disturbance linearization. The dynamic characteristics of pitching mode, rolling mode and Dutch rolling mode are obtained by analysing the linearized model. Furthermore, an IGC design procedure is also proposed in conjunction with a proportional–integral–derivative (PID) control method and fuzzy control method. A PID controller is applied in the control loop of the elevator and aileron, and the attitude angle and attitude angular velocity are used as compensation feedback, giving a simple and low-order control law. A fuzzy control method is applied to perform the cross-coupling control of rolling and yawing. Finally, the 6-DOF simulation shows the effectiveness of the developed method.

scholarly journals A Novel Adaptive Super-Twisting Sliding Mode Control Scheme with Time-Delay Estimation for a Single Ducted-Fan Unmanned Aerial Vehicle

Actuators ◽  
2021 ◽  
Vol 10 (3) ◽  
pp. 54
Author(s):  
Minh-Thien Tran ◽  
Dong-Hun Lee ◽  
Soumayya Chakir ◽  
Young-Bok Kim
Keyword(s):  
Time Delay ◽  
Sliding Mode Control ◽  
Unmanned Aerial Vehicle ◽  
Sliding Mode ◽  
Time Delay Estimation ◽  
Delay Estimation ◽  
Mode Control ◽  
Ducted Fan ◽  
Control Scheme ◽  
Aerial Vehicle

This article proposes a novel adaptive super-twisting sliding mode control scheme with a time-delay estimation technique (ASTSMC-TDE) to control the yaw angle of a single ducted-fan unmanned aerial vehicle system. Such systems are highly nonlinear; hence, the proposed control scheme is a combination of several control schemes; super-twisting sliding mode, TDE technique to estimate the nonlinear factors of the system, and an adaptive sliding mode. The tracking error of the ASTSMC-TDE is guaranteed to be uniformly ultimately bounded using Lyapunov stability theory. Moreover, to enhance the versatility and the practical feasibility of the proposed control scheme, a comparison study between the proposed controller and a proportional-integral-derivative controller (PID) is conducted. The comparison is achieved through two different scenarios: a normal mode and an abnormal mode. Simulation and experimental tests are carried out to provide an in-depth investigation of the performance of the proposed ASTSMC-TDE control system.

scholarly journals Aerodynamic Analysis of Blended Wing Body - Unmanned Aerial Vehicle (BWB-UAV) Equipped with Horizontal Stabilizers

2019 ◽  
Vol 256 ◽  
pp. 02004
Author(s):  
Nornashiha Mohd Saad ◽  
Wirachman Wisnoe ◽  
Rizal Effendy Mohd Nasir ◽  
Zurriati Mohd Ali ◽  
Ehan Sabah Shukri Askari
Keyword(s):  
Unmanned Aerial Vehicle ◽  
Cfd Simulation ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Flight Test ◽  
Longitudinal Direction ◽  
Static Stability ◽  
Pitching Moment ◽  
Aerial Vehicle ◽  
Blended Wing Body

This paper presents an aerodynamic characteristic study in longitudinal direction of UiTM Blended Wing Body-Unmanned Aerial Vehicle Prototype (BWB-UAV Prototype) equipped with horizontal stabilizers. Flight tests have been conducted and as the result, BWB experienced overturning condition at certain angle of attack. Horizontal stabilizer was added at different location and size to overcome the issue during the flight test. Therefore, Computational Fluid Dynamics (CFD) analysis is performed at different configuration of horizontal stabilizer using Spalart - Allmaras as a turbulence model. CFD simulation of the aircraft is conducted at Mach number 0.06 or v = 20 m/s at various angle of attack, α. The data of lift coefficient (CL), drag coefficient (CD), and pitching moment coefficient (CM) is obtained from the simulations. The data is represented in curves against angle of attack to measure the performance of BWB prototype with horizontal stabilizer. From the simulation, configuration with far distance and large horizontal stabilizer gives steeper negative pitching moment slope indicating better static stability of the aircraft.

scholarly journals Design of a Hand-Launched Solar-Powered Unmanned Aerial Vehicle (UAV) System for Plateau

2020 ◽  
Vol 10 (4) ◽  
pp. 1300 ◽  
Author(s):  
Xin Zhao ◽  
Zhou Zhou ◽  
Xiaoping Zhu ◽  
An Guo
Keyword(s):  
Low Temperature ◽  
Conceptual Design ◽  
Unmanned Aerial Vehicle ◽  
Design Method ◽  
Structure Design ◽  
Control Law ◽  
Trajectory Tracking Control ◽  
Plateau Area ◽  
Aerial Vehicle ◽  
Solar Powered

This paper describes our work on a small, hand-launched, solar-powered unmanned aerial vehicle (UAV) suitable for low temperatures and high altitudes, which has the perpetual flight potential for conservation missions for rare animals in the plateau area in winter. Firstly, the conceptual design method of a small, solar-powered UAV based on energy balance is proposed, which is suitable for flight in high-altitude and low-temperature area. The solar irradiance model, which can reflect the geographical location and time, was used. Based on the low-temperature discharge test of the battery, a battery weight model considering the influence of low temperature on the battery performance was proposed. Secondly, this paper introduces the detailed design of solar UAV for plateau area, including layout design, structure design, load, and avionics. To increase the proportion of solar cells covered, the ailerons were removed and a rudder was used to control both roll and yaw. Then, the dynamics model of an aileron-free layout UAV was developed, and the differences in maneuverability and stability of aileron-free UAV in plateau and plain areas were analyzed. The control law and trajectory tracking control law were designed for the aileron-free UAV. Finally, the flight test was conducted in Qiangtang, Tibet, at an altitude of 4500 m, China’s first solar-powered UAV to take off and land above 4500 m on the plateau in winter (−30 °C). The test data showed the success of the scheme, validated the conceptual design method and the success of the control system for aileron-free UAV, and analyzed the feasibility of perpetual flight carrying different loads according to the flight energy consumption data.

scholarly journals Typical Fault Estimation and Dynamic Analysis of a Leader-Follower Unmanned Aerial Vehicle Formation

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Jian Shen ◽  
Qingyu Zhu ◽  
Xiaoguang Wang ◽  
Pengyun Chen
Keyword(s):  
Dynamic Analysis ◽  
Unmanned Aerial Vehicle ◽  
Cooperative Control ◽  
Health Management ◽  
Fault Tolerant ◽  
Design Method ◽  
Observer Design ◽  
Fault Estimation ◽  
Proportional Navigation ◽  
Aerial Vehicle

In this paper, the typical fault estimation and dynamic analysis are presented for a leader-follower unmanned aerial vehicle (UAV) formation system with external disturbances. Firstly, a dynamic model with proportional navigation guidance (PNG) control of the UAV formation is built. Then, an intermediate observer design method is adopted to estimate the system states and faults simultaneously. Based on the graph theory, the topology relationship between each node in the UAV formation has been also analyzed. The estimator and the system error have been created. Moreover, the typical faults, including the components failure, airframe damage, communication failure, formation collision, and environmental impact, are also discussed for the UAV system. Based on the fault-tolerant strategy, five familiar fault models are proposed from the perspectives of fault estimation, dynamical disturbances, and formation cooperative control. With an analysis of the results of states and faults estimation, the actuator faults can be estimated precisely with component failure and wind disturbances. Furthermore, the basic dynamic characteristics of the UAV formation are discussed. Besides, a comparison of two cases related to the wind disturbance has been accomplished to verify the performance of the fault estimator and controller. The results illustrate the credibility and applicability of the fault estimation and dynamic control strategies for the UAV system which are proposed in this paper. Finally, an extension about the UAV formation prognostic health management system is expounded from the point of view of the fault-tolerant control, dynamic modeling, and multifault estimation.

AERODYNAMIC OF UITM'S BLENDED-WING-BODY UNMANNED AERIAL VEHICLE BASELINE-II EQUIPPED WITH ONE CENTRAL VERTICAL RUDDER

2015 ◽  
Vol 75 (8) ◽  
Author(s):  
Wirachman Wisnoe ◽  
Rizal E.M. Nasir ◽  
Ramzyzan Ramly ◽  
Wahyu Kuntjoro ◽  
Firdaus Muhammad
Keyword(s):  
Unmanned Aerial Vehicle ◽  
Cfd Simulation ◽  
Aerodynamic Characteristics ◽  
Control Surface ◽  
Wind Tunnel Experiments ◽  
Aerodynamic Parameter ◽  
Aerial Vehicle ◽  
Computational Fluid Dynamics Cfd ◽  
Blended Wing Body ◽  
Lift And Drag

In this paper, a study of aerodynamic characteristics of UiTM's Blended-Wing-Body Unmanned Aerial Vehicle (BWB-UAV) Baseline-II in terms of side force, drag force and yawing moment coefficients are presented through Computational Fluid Dynamics (CFD) simulation. A vertical rudder is added to the aircraft at the rear centre part of the fuselage as yawing control surface. The study consists of varying the side slip angles for various rudder deflection angles and to plot the results for each aerodynamic parameter. The comparison with other yawing control surface for the same aircraft obtained previously are also presented. For validation purpose, the lift and drag coefficients are compared with the results obtained from wind tunnel experiments. 

Aeroacoustic Analysis of an Unmanned Aerial Vehicle

2007 ◽  
Author(s):  
Peter D. Lysak ◽  
James J. Dreyer ◽  
John B. Fahnline ◽  
Dean E. Capone ◽  
John E. Poremba
Keyword(s):  
Unmanned Aerial Vehicle ◽  
Acoustic Analysis ◽  
Three Dimensional ◽  
Broadband Noise ◽  
Frequency Noise ◽  
Noise Levels ◽  
Boundary Layer Turbulence ◽  
Ducted Fan ◽  
Inflow Turbulence ◽  
Aerial Vehicle

An acoustic analysis of a ducted fan unmanned aerial vehicle (UAV) was conducted to identify the primary aeroacoustic sources and to determine the potential for reducing the radiated noise levels. Computational fluid dynamics was used to determine the three-dimensional flow field through the ducted fan in hover and maneuvering configurations. The flow solutions provided information about the blade relative velocities, spatially non-uniform inflow, inflow turbulence, boundary layer turbulence, and blade wake velocity deficits for use in acoustical models of broadband and blade passing frequency noise. The computational results were in good agreement with experimentally measured noise levels, and showed that the tonal noise was produced primarily by unsteady forces resulting from the non-uniform inflow, while the broadband noise resulted from the inflow turbulence. Based on these findings, design modifications were recommended which offer the potential to reduce the noise by more than 10 dB.

Sign in / Sign up

Export Citation Format

Share Document