A Transonic Mixed Flow Compressor for an Extreme Duty

2014 ◽  
Author(s):  
Hamid Hazby ◽  
Michael Casey ◽  
Ryusuke Numakura ◽  
Hideaki Tamaki
Keyword(s):  
Test Data ◽  
Pressure Rise ◽  
High Flow ◽  
Flow Coefficient ◽  
Compressor Stage ◽  
Aerodynamic Optimization ◽  
Mixed Flow ◽  
Axial Compressors ◽  
Blade Shape ◽  
Flow Compressor

This paper describes the design of a transonic mixed flow compressor stage for an extreme duty, with an extremely high flow coefficient (Φ) of 0.25 and a high isentropic pressure rise coefficient (ψ) of 0.56. The impeller design makes use of modern aerodynamic practice from radial and transonic axial compressors, whereby the aerodynamic blade shape involved arbitrary surfaces on several spanwise sections. Some aspects of the aerodynamic optimization of the design were limited by mechanical considerations, but nevertheless the test data obtained on a prototype stage demonstrates that acceptable performance levels can be achieved at these extreme design conditions, although map width enhancement devices were needed to obtain an acceptable operating range. The test data is compared with CFD predictions to demonstrate the validity of the design methods used.

A Transonic Mixed Flow Compressor for an Extreme Duty

2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Hamid Hazby ◽  
Michael Casey ◽  
Ryusuke Numakura ◽  
Hideaki Tamaki
Keyword(s):  
Test Data ◽  
Pressure Rise ◽  
High Flow ◽  
Flow Coefficient ◽  
Aerodynamic Optimization ◽  
Mixed Flow ◽  
Axial Compressors ◽  
Blade Shape ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Compressor

This paper describes the design of a transonic mixed flow compressor stage for an extreme duty, with an extremely high flow coefficient (φ) of 0.25 and a high isentropic pressure rise coefficient (ψ) of 0.56. The impeller design makes use of modern aerodynamic practice from radial and transonic axial compressors, whereby the aerodynamic blade shape involved arbitrary surfaces on several spanwise sections. Some aspects of the aerodynamic optimization of the design were limited by mechanical considerations, but nevertheless the test data obtained on a prototype stage demonstrates that acceptable performance levels can be achieved at these extreme design conditions, although map width enhancement (MWE) devices were needed to obtain an acceptable operating range. The test data are compared with computational fluid dynamics (CFD) predictions to demonstrate the validity of the design methods used.

Assessment of a Novel Non-Axial Counter-Rotating Compressor Concept for Aero-Engines

2018 ◽  
Author(s):  
Quentin Dejour ◽  
Huu Duc Vo
Keyword(s):  
Pressure Rise ◽  
Axial Direction ◽  
Boundary Layer Separation ◽  
Low Flow ◽  
Compressor Stage ◽  
Mixed Flow ◽  
Stall Margin ◽  
High Loss ◽  
Multi Stage ◽  
Flow Compressor

This paper presents the first assessment of a new non-axial counter-rotating compressor concept. This concept consists of replacing the stator of a mixed-flow compressor stage or the diffuser of a centrifugal compressor stage with a counter-rotating rotor that will turn the flow back to the axial direction with much lower diffusion factor, while providing the equivalent in work of the upstream mixed-flow rotor or impeller. This concept has two advantages. First, the very high stage pressure rise means that only a single counter-rotating rotor may be required, making mechanical implementation simpler than for multi-stage axial counter-rotating compressors. Second, the replacement of the high flow turning (high loss) stator/diffuser in a non-axial stage with a low flow turning counter-rotating rotor gives the new concept potential for achieving higher efficiency than conventional non-axial compressors. As a first proof of concept, a subsonic counter-rotating mixed-flow compressor and its conventional (i.e. rotor-stator) equivalent have been designed with the intent of being implemented in a test rig. CFD simulations have been carried out for a comparative evaluation of both configurations. Results show that the counter-rotating mixed-flow compressor produces more than double the pressure rise of its conventional version with a slightly higher peak-efficiency while having a smaller axial length. Moreover, the counter-rotating configuration has a better stall margin than its conventional counterpart, for which the boundary layer separation from excessive flow turning in the stator causes early stall.

Experimental Study on the Influence of Casing Treatment on Near-Stall Unsteady Behavior of a Mixed-Flow Compressor

2019 ◽  
Author(s):  
Juan Du ◽  
Felix Kauth ◽  
Jichao Li ◽  
Qianfeng Zhang ◽  
Joerg R. Seume
Keyword(s):  
Stability Limit ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Surprising Result ◽  
Mixed Flow ◽  
Stall Inception ◽  
Casing Treatment ◽  
Axial Compressors ◽  
Flow Compressor ◽  
Unsteady Behavior

Abstract This paper aims at experimentally demonstrating the effects of axial slot casing treatment and tip gap variation on compressor performance, unsteady tip clearance flow, and stall inception features in a highly-loaded mixed-flow compressor at partspeed. Two tip gaps (0.32% and 0.64% of rotor blade chord at mid-span) were tested at three rotational speeds. A semicircular axial slot casing treatment improves compressor stability. The experimental results show that this casing treatment significantly moves the stability limit at partial speeds towards lower mass flow for both tip gaps, compared to the reference case without casing treatment. In the case of the compressor with casing treatment, efficiency increases for the large tip gap and decreases for the small tip gap. Dynamic pressure transducers installed in the casing upstream and along the rotor tip chord direction are used to detect the unsteady behavior of tip region flow and stall inception signals of the compressor. The characteristic frequency in the tip region decreases, and the oscillating amplitude first decreases and then increases during the throttling process, regardless of tip gap size or casing treatment. For axial compressors, by contrast, the observation in previous work has been an increase of the oscillating amplitude with decreasing flow coefficient. This is a surprising result of our work. Neither experiment nor CFD so far was able to explain why the trend in this mixed-flow compressor is different from the trend expected from axial compressors. The compressor stalls through the spike stall inception both with and without casing treatment. This observation also differs from recent studies on axial compressors, which demonstrated that casing treatments could change the type of stall inception. The unstable disturbance indicating initial stall inception initially appears in the blade tip region from blade mid-chord to trailing edge, and then propagates upstream towards the leading edge. This disturbance might be generated by the reversed flow separation near mid-chord.

scholarly journals Introduction of an Universal Scale-Up Method for the Efficiency of Axial and Centrifugal Fans

2014 ◽  
Author(s):  
Peter F. Pelz ◽  
Stefan S. Stonjek
Keyword(s):  
Test Data ◽  
Scale Up ◽  
Pressure Rise ◽  
Flow Coefficient ◽  
Total Efficiency ◽  
Scaling Method ◽  
Centrifugal Fans ◽  
Axial Fans ◽  
Definition Of ◽  
Acceptance Tests

Acceptance tests on large fans to prove the performance (efficiency and total pressure rise) to the customer are expensive and sometimes even impossible to perform. Hence there is a need for the manufacturer to reliably predict the performance of fans from measurements on down-scaled test fans. The commonly used scale-up formulas give satisfactorily results only near the design point, where inertia losses are small in comparison to frictional losses. At part- and overload the inertia losses are dominant and the scale-up formulas used so far fail. In 2013 Pelz and Stonjek introduced a new scaling method which fullfills the demands ( [1], [2]). This method considers the influence of surface roughness and geometric variations on the performance. It consists basically of two steps: Initially, the efficiency is scaled. Efficiency scaling is derived analytically from the definition of the total efficiency. With the total derivative it can be shown that the change of friction coefficient is inversely proportional to the change of efficiency of a fan. The second step is shifting the performance characteristic to a higher value of flow coefficient. It is the task of this work to improve the scaling method which was previously introduced by Pelz and Stonjek by treating the rotor/impeller and volute/stator separately. The validation of the improved scale-up method is performed with test data from two axial fans with a diameter of 1000 mm/250mm and three centrifugal fans with 2240mm/896mm/224mm diameter. The predicted performance characteristics show a good agreement to test data.

1D and 3D-Design Strategies for Pressure Slope Optimization of High-Flow Transonic Centrifugal Compressor Impellers

2018 ◽  
Author(s):  
A. Hildebrandt ◽  
T. Ceyrowsky
Keyword(s):  
Centrifugal Compressor ◽  
High Flow ◽  
Flow Coefficient ◽  
Design Parameters ◽  
Angle Distribution ◽  
Compressor Stage ◽  
Impeller Blade ◽  
Design Point ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

The present paper deals with the numerical and theoretical investigations of the effect of geometrical dimensions and 1D-design parameters on the impeller pressure slope of a transonic centrifugal compressor stage for industrial process application. A database being generated during the multi-objective and multi-point design process of a high flow coefficient impeller, comprising 545 CFD (Computational Fluid Dynamics) designs is investigated in off-design and design conditions by means of RANS (Reynolds Averaged Navier Stokes) simulation of an impeller with vaneless diffuser. For high flow coefficients of 0.16 < phi < 0.18, the CFD-setup has been validated against measurement data regarding stage and impeller performance taken from MAN test rig experimental data for a centrifugal compressor stage of similar flow coefficient. The paper aims at answering the question how classical design parameter, such as the impeller blade angle distribution, impeller suction diameter and camber line length affect the local and total relative diffusion and pressure slope towards impeller stall operation. A second order analysis of the CFD database is performed by cross-correlating the CFD data with results from impeller two-zone 1D modelling and a rapid loading calculation process by Stanitz and Prian. The statistical covariance of first order 1D-analysis parameters such as the mixing loss of the impeller secondary flow, the slip factor, impeller flow incidence is analyzed, thereby showing strong correlation with the design and off-design point efficiency and pressure slope. Finally, guide lines are derived in order to achieve either optimized design point efficiency or maximum negative pressure slope characteristics towards impeller stall operation.

Influence of distorted inflows on the performance of a contra-rotating fan

2020 ◽  
pp. 1-18
Author(s):  
M.P. Manas ◽  
A.M. Pradeep
Keyword(s):  
Pressure Rise ◽  
Aircraft Engine ◽  
High Flow ◽  
Flow Coefficient ◽  
Potential Candidate ◽  
Blade Surface ◽  
Axial Fan ◽  
Stall Inception ◽  
Relative Contribution ◽  
Inflow Conditions

ABSTRACT A contra-rotating fan offers several aerodynamic advantages that make it a potential candidate for future aircraft engine configurations. Stall in a contra-rotating axial fan is interesting since instabilities could arise from either or both of the rotors. In this experimental study, a contra-rotating axial fan is analysed under clean or distorted inflow conditions to understand its performance and stall inception characteristics. The steady and unsteady measurements identified the relative contribution of each rotor towards the performance of the stage. The tip of rotor-1 is identified to be the most critical region of the contra-rotating fan. The contribution of rotor-2 to the overall loading of the stage is observed to be relatively less than rotor-1. The penalty due to distortion in the stage pressure rise is mostly felt by rotor-1, while rotor-2 also shows a reduction in performance for distorted inflows. Rotor-2 stalls at a high flow coefficient marking the initiation of partial stall of the stage, and the stall of the whole stage occurs once rotor-1 stalls. A fluid phenomenon that is attached to the blade surface marks the stall of rotor-1, and this fluid phenomenon initially rotates at a speed close to the speed of rotation of the blade. As the stage moves towards the fully developed stall, this fluid phenomenon sheds from the blade surface. The fluid phenomenon thus propagates at a speed much lower than the rotational speed of the blade during fully developed stall.

Experimental Investigations on Mixed Flow Impeller and Vane Diffuser Under Various Operating Conditions

2012 ◽  
Author(s):  
D. Ramesh Rajakumar ◽  
S. Ramamurthy ◽  
M. Govardhan
Keyword(s):  
Pressure Ratio ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Experimental Investigations ◽  
Compressor Stage ◽  
Mixed Flow ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Flow Compressor ◽  
Vane Diffuser

Experimental Investigations are carried out to study the effect of tip clearance flow in a mixed flow compressor stage. Two configurations, namely; constant and variable clearance gaps between impeller and stationary shroud are considered. For the purpose of the present investigations, a mixed flow compressor stage is designed and fabricated. The flow investigations were carried out in a closed circuit compressor rig. Detailed steady and unsteady measurements were carried out for three clearance gaps, namely; 0.5 mm, 0.75 mm, 0.9 mm. From the experimental investigations it is shown that constant tip clearance configurations show better performance in terms of pressure ratio and efficiency compared to variable clearance configurations. For a given configuration the pressure ratio and efficiency of the stage decrease with increase in the tip gap without indicating any optimum value. Tip clearance flow has considerable effect on the flow through the diffuser and the unsteady flow gets amplified and carried away into the vane diffuser.

Bleed-Induced Distortion in Axial Compressors

2014 ◽  
Author(s):  
S. D. Grimshaw ◽  
G. Pullan ◽  
T. Walker
Keyword(s):  
Axial Flow ◽  
Flow Coefficient ◽  
Axial Compressors ◽  
Swirl Angle ◽  
Geometric Factors ◽  
Circumferential Distribution ◽  
Flow Compressor ◽  
The Stability ◽  
Chamber Size ◽  
Distribution Of Flow

In this paper, the influence of non-uniform bleed extraction on the stability of an axial flow compressor is quantified. Non-uniformity can be caused by several geometric factors (for example, plenum chamber size or number of off-take ducts) and a range of configurations is examined experimentally in a single stage compressor. It is shown that non-uniform bleed leads to a circumferential distribution of flow coefficient and swirl angle at inlet to the downstream stage. The resultant distribution of rotor incidence causes stall to occur at a higher flow coefficient than if the same total bleed rate had been extracted uniformly around the circumference. The loss of operating range caused by the non-uniform inlet flow correlates with the peak sector-averaged bleed non-uniformity for all the bleed configurations tested. A connection is made between the analysis of non-uniform bleed extraction and the familiar “DCθ” criterion used to characterize inlet total pressure distortion.

Aerodynamic Design and Rig Test Validation of a High Flow Coefficient Process Centrifugal Compressor Stage

2021 ◽  
Author(s):  
Louis Larosiliere ◽  
Vishal Jariwala ◽  
Kapil Panchal
Keyword(s):  
Centrifugal Compressor ◽  
High Flow ◽  
Design Flow ◽  
Flow Coefficient ◽  
Test Validation ◽  
Lapse Rate ◽  
Compressor Stage ◽  
Aerodynamic Design ◽  
Centrifugal Compressor Stage ◽  
Very High

Abstract Efficient and diametrically compact very high flow coefficient stages with wide operability are desirable for economic reasons in many process multistage centrifugal compressor applications. Such stages present special aerodynamic and mechanical design challenges. There is often a sizeable efficiency lapse rate as well as substantial reduction in useable operating range for traditional stages having design flow coefficients greater than 0.15 and moderate to high machine Mach numbers. This paper describes aerodynamic design and rig test validation of a very high flow coefficient (φ0 = 0.237) process centrifugal compressor stage. Some useful experience of the detailed design work required to navigate certain technical challenges and its rig test validation are reflected in the manuscript. A relatively high machine Mach number (MU ∼ 0.878) mixed-flow shrouded impeller matched with a curved radial vaneless diffuser and return channel was developed. Test results confirmed that the principal aerodynamic design intents were met or exceeded. A sensible design strategy guided by a well-anchored design method is shown to successfully extend an existing stage portfolio to very high-flow coefficients for multistage process centrifugal compressor applications.

Analytical and Test Experiences Using a Rib Diffuser in a High Flow Centrifugal Compressor Stage

2001 ◽  
Author(s):  
James M. Sorokes ◽  
Jason A. Kopko
Keyword(s):  
Centrifugal Compressor ◽  
Quantitative Agreement ◽  
High Flow ◽  
Flow Coefficient ◽  
Centrifugal Impeller ◽  
Compressor Stage ◽  
Vaneless Diffuser ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Qualitative And Quantitative

The paper addresses the use of a rib style (partial height) vaned diffuser to improve the flowfield downstream of a high flow coefficient centrifugal impeller. Empirical and analytical (3-D CFD) results are presented for both the original vaneless diffuser and the replacement rib configuration. Comparisons are made between the CFD results and the data obtained through single stage rig (SSTR) testing. Comments are offered regarding the qualitative and quantitative agreement between the empirical and analytical results.

Sign in / Sign up

Export Citation Format

Share Document