Supporting Structure Performances Analysis of Heavy-Duty Gas Turbine Based on Fluid-Solid Coupling Method

2015 ◽  
Author(s):  
Guohui Xu ◽  
Jian Zhou ◽  
Mingjian Lu ◽  
Haipeng Geng ◽  
Yanhua Sun ◽  
...  
Keyword(s):  
Thermal Stress ◽  
High Temperature ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Thermal Deformation ◽  
Coupled Model ◽  
Strength Analysis ◽  
Cooling Flow ◽  
Heavy Duty Gas Turbine ◽  
Steady State Heat Transfer

In order to achieve high working efficiency, modern gas turbines operate at high temperature which is close to the melting points of metal alloys. However, the support of turbine end suffers the thermal deformation. And the journal center position is also changed due to the effects of high temperature and shaft gravity. Tangential or radial supporting structures, which are composed of supporting struts, diffuser cones, hot and cooling fluid channel, are widely used in gas turbine hot end. Cooling technology is usually used to keep the bearing temperature in a reasonable range to meet requirements of strength and deformation of the supporting struts. In this paper, three major assumptions are proposed: (a) radiation is not considered, (b) cooling flow system is only partially modeled and analysis assumes significantly higher cooling flow that is not typical for current engines, and (c) only steady state heat transfer is considered. And a 3D fluid-solid coupled model based on finite-element method (FEM) is built to analyze the performances of both the tangential and the radial support. The temperature distribution, thermal deformation and stress of supports are obtained from CFD and strength analysis. The results show that either the tangential or radial support is used in a 270MW gas turbine; the thermal stress is about 90.3% of total stress which is produced by both thermal effects and shaft gravity. Comparing to the results from radial supports, it can be seen that the struts stress and position variation of journal center of tangential support are smaller. Due to a rotational effect of the bearing housing caused by the deformation of the tangential struts, the thermal stress in these tangential struts can be relieved to some extent. When both thermal effect and shaft gravity are considered, the stress of each tangential supporting strut is almost uniformly distributed, which is beneficial to the stability of rotor system in the gas turbine.

An Improved Nickel Based MIMS Thermocouple for High Temperature Gas Turbine Applications

2012 ◽  
Author(s):  
Michele Scervini ◽  
Catherine Rae
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
High Temperatures ◽  
Gas Turbines ◽  
Material Science ◽  
University Of Cambridge ◽  
Type K ◽  
Metallurgical Analysis ◽  
The University ◽  
High Temperature Gas

A new Nickel based thermocouple for high temperature applications in gas turbines has been devised at the Department of Material Science and Metallurgy of the University of Cambridge. This paper describes the new features of the thermocouple, the drift tests on the first prototype and compares the behaviour of the new sensor with conventional mineral insulated metal sheathed Type K thermocouples: the new thermocouple has a significant improvement in terms of drift and temperature capabilities. Metallurgical analysis has been undertaken on selected sections of the thermocouples exposed at high temperatures which rationalises the reduced drift of the new sensor. A second prototype will be tested in follow-on research, from which further improvements in drift and temperature capabilities are expected.

Development and Fabrication of Silicon Nitride Components for Ceramic Gas Turbine

1997 ◽  
Author(s):  
Keisuke Makino ◽  
Ken-Ichi Mizuno ◽  
Toru Shimamori
Keyword(s):  
High Temperature ◽  
Silicon Nitride ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Blades ◽  
High Strength ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Spark Plug ◽  
Power Turbine

NGK Spark Plug Co., Ltd. has been developing various silicon nitride materials, and the technology for fabricating components for ceramic gas turbines (CGT) using theses materials. We are supplying silicon nitride material components for the project to develop 300 kW class CGT for co-generation in Japan. EC-152 was developed for components that require high strength at high temperature, such as turbine blades and turbine nozzles. In order to adapt the increasing of the turbine inlet temperature (TIT) up to 1,350 °C in accordance with the project goals, we developed two silicon nitride materials with further unproved properties: ST-1 and ST-2. ST-1 has a higher strength than EC-152 and is suitable for first stage turbine blades and power turbine blades. ST-2 has higher oxidation resistance than EC-152 and is suitable for power turbine nozzles. In this paper, we report on the properties of these materials, and present the results of evaluations of these materials when they are actually used for CGT components such as first stage turbine blades and power turbine nozzles.

Comparison of 3D Unsteady Transient Conjugate Heat Transfer Analysis on a High Pressure Cooled Turbine Stage With Experimental Data

2017 ◽  
Author(s):  
Jong-Shang Liu ◽  
Mark C. Morris ◽  
Malak F. Malak ◽  
Randall M. Mathison ◽  
Michael G. Dunn
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Flux ◽  
High Pressure ◽  
High Temperature ◽  
Gas Turbine ◽  
Conjugate Heat Transfer ◽  
Turbine Rotor ◽  
Turbine Stage ◽  
Cooling Flow

In order to have higher power to weight ratio and higher efficiency gas turbine engines, turbine inlet temperatures continue to rise. State-of-the-art turbine inlet temperatures now exceed the turbine rotor material capability. Accordingly, one of the best methods to protect turbine airfoil surfaces is to use film cooling on the airfoil external surfaces. In general, sizable amounts of expensive cooling flow delivered from the core compressor are used to cool the high temperature surfaces. That sizable cooling flow, on the order of 20% of the compressor core flow, adversely impacts the overall engine performance and hence the engine power density. With better understanding of the cooling flow and accurate prediction of the heat transfer distribution on airfoil surfaces, heat transfer designers can have a more efficient design to reduce the cooling flow needed for high temperature components and improve turbine efficiency. This in turn lowers the overall specific fuel consumption (SFC) for the engine. Accurate prediction of rotor metal temperature is also critical for calculations of cyclic thermal stress, oxidation, and component life. The utilization of three-dimensional computational fluid dynamics (3D CFD) codes for turbomachinery aerodynamic design and analysis is now a routine practice in the gas turbine industry. The accurate heat-transfer and metal-temperature prediction capability of any CFD code, however, remains challenging. This difficulty is primarily due to the complex flow environment of the high-pressure turbine, which features high speed rotating flow, coupling of internal and external unsteady flows, and film-cooled, heat transfer enhancement schemes. In this study, conjugate heat transfer (CHT) simulations are performed on a high-pressure cooled turbine stage, and the heat flux results at mid span are compared to experimental data obtained at The Ohio State University Gas Turbine Laboratory (OSUGTL). Due to the large difference in time scales between fluid and solid, the fluid domain is simulated as steady state while the solid domain is simulated as transient in CHT simulation. This paper compares the unsteady and transient results of the heat flux on a high-pressure cooled turbine rotor with measurements obtained at OSUGTL.

Assessment of the Potential of Combined Micro Gas Turbine and High Temperature Fuel Cell Systems

2002 ◽  
Author(s):  
Dieter Bohn ◽  
Nathalie Po¨ppe ◽  
Joachim Lepers
Keyword(s):  
Fuel Cells ◽  
High Temperature ◽  
Fuel Cell ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Advanced Materials ◽  
Cell Systems ◽  
Micro Gas Turbine ◽  
Technological Assessment

The present paper reports a detailed technological assessment of two concepts of integrated micro gas turbine and high temperature (SOFC) fuel cell systems. The first concept is the coupling of micro gas turbines and fuel cells with heat exchangers, maximising availability of each component by the option for easy stand-alone operation. The second concept considers a direct coupling of both components and a pressurised operation of the fuel cell, yielding additional efficiency augmentation. Based on state-of-the-art technology of micro gas turbines and solid oxide fuel cells, the paper analyses effects of advanced cycle parameters based on future material improvements on the performance of 300–400 kW combined micro gas turbine and fuel cell power plants. Results show a major potential for future increase of net efficiencies of such power plants utilising advanced materials yet to be developed. For small sized plants under consideration, potential net efficiencies around 70% were determined. This implies possible power-to-heat-ratios around 9.1 being a basis for efficient utilisation of this technology in decentralised CHP applications.

scholarly journals Thermodynamic modelling and efficiency analysis of a class of real indirectly fired gas turbine cycles

2009 ◽  
Vol 13 (4) ◽  
pp. 41-48
Author(s):  
Zheshu Ma ◽  
Zhenhuan Zhu
Keyword(s):  
High Temperature ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Waste Heat ◽  
Operational Parameters ◽  
Forecast Performance ◽  
Micro Gas Turbine ◽  
Temperature Heat

Indirectly or externally-fired gas-turbines (IFGT or EFGT) are novel technology under development for small and medium scale combined power and heat supplies in combination with micro gas turbine technologies mainly for the utilization of the waste heat from the turbine in a recuperative process and the possibility of burning biomass or 'dirty' fuel by employing a high temperature heat exchanger to avoid the combustion gases passing through the turbine. In this paper, by assuming that all fluid friction losses in the compressor and turbine are quantified by a corresponding isentropic efficiency and all global irreversibilities in the high temperature heat exchanger are taken into account by an effective efficiency, a one dimensional model including power output and cycle efficiency formulation is derived for a class of real IFGT cycles. To illustrate and analyze the effect of operational parameters on IFGT efficiency, detailed numerical analysis and figures are produced. The results summarized by figures show that IFGT cycles are most efficient under low compression ratio ranges (3.0-6.0) and fit for low power output circumstances integrating with micro gas turbine technology. The model derived can be used to analyze and forecast performance of real IFGT configurations.

scholarly journals The Role of the Recuperator in High Performance Gas Turbine Applications

1978 ◽  
Author(s):  
C. F. McDonald
Keyword(s):  
High Temperature ◽  
Heat Exchanger ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Performance ◽  
Waste Heat ◽  
Closed Cycle ◽  
Exhaust Waste Heat ◽  
Prime Movers

With soaring fuel costs and diminishing clean fuel availability, the efficiency of the industrial gas turbine must be improved by utilizing the exhaust waste heat by either incorporating a recuperator or by co-generation, or both. In the future, gas turbines for power generation should be capable of operation on fuels hitherto not exploited in this prime-mover, i.e., coal and nuclear fuel. The recuperative gas turbine can be used for open-cycle, indirect cycle, and closed-cycle applications, the latter now receiving renewed attention because of its adaptability to both fossil (coal) and nuclear (high temperature gas-cooled reactor) heat sources. All of these prime-movers require a viable high temperature heat exchanger for high plant efficiency. In this paper, emphasis is placed on the increasingly important role of the recuperator and the complete spectrum of recuperative gas turbine applications is surveyed, from lightweight propulsion engines, through vehicular and industrial prime-movers, to the large utility size nuclear closed-cycle gas turbine. For each application, the appropriate design criteria, types of recuperator construction (plate-fin or tubular etc.), and heat exchanger material (metal or ceramic) are briefly discussed.

Advancement in Heated Spin Testing Technologies

2013 ◽  
Author(s):  
Hiroaki Endo ◽  
Robert Wetherbee ◽  
Nikhil Kaushal
Keyword(s):  
High Temperature ◽  
Gas Turbine ◽  
Material Properties ◽  
Gas Turbines ◽  
Multiple Scales ◽  
Thermal Conditions ◽  
Complex Stress ◽  
Operating Conditions ◽  
Mechanical Cycling ◽  
Testing Techniques

An ever more rapidly accelerating trend toward pursuing more efficient gas turbines pushes the engines to hotter and more arduous operating conditions. This trend drives the need for new materials, coatings and associated modeling and testing techniques required to evaluate new component design in high temperature environments and complex stress conditions. This paper will present the recent advances in spin testing techniques that are capable of creating complex stress and thermal conditions, which more closely represent “engine like” conditions. The data from the tests will also become essential references that support the effort in Integrated Computational Materials Engineering (ICME) and in the advances in rotor design and lifing analysis models. Future innovation in aerospace products is critically depended on simultaneous engineering of material properties, product design, and manufacturing processes. ICME is an emerging discipline with an approach to design products, the materials that comprise them, and their associated materials processing methods by linking materials models at multiple scales (Structural, Macro, Meso, Micro, Nano, etc). The focus of the ICME is on the materials; understanding how processes produce material structures, how those structures give rise to material properties, and how to select and/or engineer materials for a given application [34]. The use of advanced high temperature spin testing technologies, including thermal gradient and thermo-mechanical cycling capabilities, combined with the innovative use of modern sensors and instrumentation methods, enables the examination of gas turbine discs and blades under the thermal and the mechanical loads that are more relevant to the conditions of the problematic damages occurring in modern gas turbine engines.

Experience With Large Heavy-Duty Gas Turbine Rotors

1981 ◽  
Author(s):  
O. R. Schmoch ◽  
B. Deblon
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Rotor ◽  
Strength Properties ◽  
Operating Conditions ◽  
Material Strength ◽  
Heavy Duty ◽  
Turbine Rotors ◽  
Heavy Duty Gas Turbine ◽  
Response To Temperature

The peripheral speeds of the rotors of large heavy-duty gas turbines have reached levels which place extremely high demands on material strength properties. The particular requirements of gas turbine rotors, as a result of the cycle, operating conditions and the ensuing overall concepts, have led different gas turbine manufacturers to produce special structural designs to resolve these problems. In this connection, a report is given here on a gas turbine rotor consisting of separate discs which are held together by a center bolt and mutually centered by radial serrations in a manner permitting expansion and contraction in response to temperature changges. In particular, the experience gained in the manufacture, operation and servicing are discussed.

Three-Dimensional Time-Resolved Flow Field in the First and Last Turbine Stage of a Heavy Duty Gas Turbine: Part II — Interpretation of Blade Pressure Fluctuations

2000 ◽  
Author(s):  
Martin von Hoyningen-Huene ◽  
Wolfram Frank ◽  
Alexander R. Jung
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Fluctuations ◽  
Three Dimensional ◽  
Potential Interaction ◽  
Heavy Duty ◽  
Turbine Stage ◽  
Count Ratio ◽  
Heavy Duty Gas Turbine

Unsteady stator-rotor interaction in gas turbines has been investigated experimentally and numerically for some years now. Most investigations determine the pressure fluctuations in the flow field as well as on the blades. So far, little attention has been paid to a detailed analysis of the blade pressure fluctuations. For further progress in turbine design, however, it is mandatory to better understand the underlying mechanisms. Therefore, computed space–time maps of static pressure are presented on both the stator vanes and the rotor blades for two test cases, viz the first and the last turbine stage of a modern heavy duty gas turbine. These pressure fluctuation charts are used to explain the interaction of potential interaction, wake-blade interaction, deterministic pressure fluctuations, and acoustic waveswith the instantaneous surface pressure on vanes and blades. Part I of this two-part paper refers to the same computations, focusing on the unsteady secondary now field in these stages. The investigations have been performed with the flow solver ITSM3D which allows for efficient simulations that simulate the real blade count ratio. Accounting for the true blade count ratio is essential to obtain the correct frequencies and amplitudes of the fluctuations.

Sign in / Sign up

Export Citation Format

Share Document