Performance Analysis of an Electric Turbocompounding System for a Hybrid Vehicle Diesel Engine

2015 ◽  
Author(s):  
Zhanming Ding ◽  
Weilin Zhuge ◽  
Yangjun Zhang ◽  
Yong Yin ◽  
Shuyong Zhang
Keyword(s):  
Diesel Engine ◽  
Waste Heat ◽  
Combustion Engine ◽  
Control Strategies ◽  
Full Range ◽  
Engine Performance ◽  
Driving Cycle ◽  
Operating Conditions ◽  
Full Load ◽  
Power Turbine

Waste heat recovery (WHR) is one of the main approaches to improve the internal combustion engine (ICE) overall efficiency and reduce emissions. The electric turbocompounding (ETC) technology is considered as a promising WHR technology for vehicle engines due to its compactness and light weight. In order to improve the overall fuel efficiency of the engine at practical operating conditions, the impacts of the implementation of the ETC system should be investigated not only at engine full load conditions, but also under practical driving cycles. In this paper, an ETC system was designed for a 4.75 L diesel engine, in which a power turbine was installed down-stream to the turbocharger turbine. A performance simulation model of the ETC engine was developed on the basis of the diesel engine model, which was validated against engine performance experimental data. The control strategies of the wastegate of turbocharger turbine, the wastegate of power turbine and the operating torque of generator were determined. The relative variation in BSFC was studied under full range of operating conditions, and results show that the maximum improvement of fuel economy is 6.7% at an engine speed of 1000 rpm and 70% of full load, in comparison with the baseline diesel engine. Main factors lead to the performance differences between the ETC engine and the baseline engine were analyzed. Furthermore, the performance of the ETC engine under the C-WTVC driving cycle was investigated. Results show that the implementation of the ETC system resulted in a 1.2% fuel consumption reduction under the C-WTVC driving cycle.

scholarly journals Experimental analysis of absorption refrigeration system driven by waste heat of diesel engine exhaust

2019 ◽  
Vol 23 (1) ◽  
pp. 149-157
Author(s):  
Mukul Kumar ◽  
Randip Das
Keyword(s):  
Diesel Engine ◽  
Waste Heat ◽  
Combustion Engine ◽  
Engine Performance ◽  
Exhaust System ◽  
Bench Test ◽  
Exhaust Gas ◽  
Absorption Refrigeration ◽  
Refrigeration System ◽  
Absorption Refrigeration System

This work presents an experimental study of an ammonia-water absorption refrigeration system using the exhaust of an internal combustion engine as energy source. The exhaust gas energy availability, the performance of the absorption refrigeration system and the engine performance are evaluated. A commercial turbocharged Diesel engine has been tested in a bench test dynamometer, with the absorption refrigeration system adapted to the exhaust system. The maximum COP obtained from the refrigeration system is 0.136 and it has been shown that heat energy available with exhaust gas is capable of producing sufficient cooling capacity for air conditioning the vehicle without requiring any energy input from the engine.

Development of a Multipoint Matching Method for Turbocompound Systems

2016 ◽  
Author(s):  
Zhanming Ding ◽  
Weilin Zhuge ◽  
Yangjun Zhang ◽  
Yong Yin ◽  
Shuyong Zhang
Keyword(s):  
Internal Combustion Engines ◽  
Waste Heat ◽  
Single Point ◽  
Poor Performance ◽  
Driving Cycle ◽  
Operating Conditions ◽  
Matching Method ◽  
Matching Process ◽  
Power Turbine ◽  
Operating Points

Turbocompounding is a promising waste heat recovery technology to improve fuel economy of internal combustion engines and comply with increasingly stringent emission regulations. The performance of a turbocompound engine is significantly influenced by the matching of the turbocharger turbine and the power turbine. Conventionally, the matching of the turbocharger turbine and power turbine is carried out at a single operating point. Single-point matched turbocompound systems tends to have poor performance at off-design operating conditions, which restrained the fuel-saving potential of turbocompound engines under driving cycle conditions. In the present study, a multipoint matching method for turbocompound systems was developed, which was essentially an optimization process of the swallowing capacities of the turbocharger turbine and the power turbine to achieve best performance at multiple matching points. In order to improve the performance of turbocompound engines under driving cycle conditions, common operating points of a driving cycle were used as matching points in the matching process. Common operating points under a driving cycle were determined by clustering the dynamic profiles of the driving cycle. A simulation study was carried out to examine the effectiveness of the multipoint matching method. The performance of the multipoint matched turbocompound system was compared against two single-point matched turbocompound systems under stationary operating points and driving cycle conditions respectively. According to the simulation results, the multipoint matched turbocompound system could attain satisfactory BSFC benefit under a wider operating range when compared with the two single-point matched turbocompound systems. The multipoint matched turbocompound engine showed the largest reduction in fuel consumption under driving cycle conditions.

Numerical Calibration of Diesel Engine Variable Valve Timing

2012 ◽  
Vol 516-517 ◽  
pp. 628-633
Author(s):  
Sheng Ou Hu ◽  
Ren Xian Li
Keyword(s):  
Diesel Engine ◽  
Working Conditions ◽  
Combustion Engine ◽  
Engine Performance ◽  
Simulation Method ◽  
Calibration Method ◽  
Operating Conditions ◽  
Variable Valve Timing ◽  
Valve Timing ◽  
Variable Valve

The performance of internal combustion engine can be improved by using variable valve timing technology. but how to get the optimal inlet/export valve open or close angles under various operating conditions still relies mainly on testing calibration method. By means of one-dimensional working process simulation method, the performance of a four cylinder diesel engine was simulated, and the influences of diffrent inlet/export valve timing on engine performances were compared. Optimum valve timing values and engine performances under thirty kinds of working conditions were gotton. After that, the engine performances compared with that without variable valve timing. Simulation results show that the engine performance, especially the emission performance, can be improved at all simulation working conditions. The method used in this paper may be a new way for calibration of optimal valve timing.

scholarly journals Innovative Control Strategies for the Diagnosis of Injector Performance in an Internal Combustion Engine via Turbocharger Speed

Energies ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1420 ◽  
Author(s):  
Michele Becciani ◽  
Luca Romani ◽  
Giovanni Vichi ◽  
Alessandro Bianchini ◽  
Go Asai ◽  
...  
Keyword(s):  
Combustion Engine ◽  
Control Strategies ◽  
Integrated Control ◽  
Combustion Process ◽  
Engine Performance ◽  
Operating Conditions ◽  
Correct Operation ◽  
Control Units ◽  
The Right ◽  
High Level

In order to ensure a high level of performance and to comply with the increasingly severe limitations in terms of fuel consumption and pollution emissions, modern diesel engines need continuous monitoring of their operating conditions by their control units. With particular focus on turbocharged engines, which are presently the standard in a large number of applications, the use of the average and the instantaneous turbocharger speeds is thought to represent a valuable feedback of the engine behavior, especially for the identification of the cylinder-to-cylinder injection variations. The correct operation of the injectors and control of the injected fuel quantity allow the controller to ensure the right combustion process and maintain engine performance. In the present study, two different techniques are presented to fit this scope. The techniques are discussed and experimentally validated, leading to the definition of an integrated control strategy, which features the main benefits of the two, and is able to correctly detect the cylinder-to-cylinder injection variation and, consequently, properly correct the injection in each cylinder in order to balance the engine behavior. In addition, the possibility of detecting misfiring events was assessed.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

The WLTC vs NEDC: A Case Study on the Impacts of Driving Cycle on Engine Performance and Fuel Consumption

2021 ◽  
Vol 18 (3) ◽  
pp. 9071-9081
Author(s):  
Jakub Lasocki
Keyword(s):  
Fuel Consumption ◽  
Combustion Engine ◽  
Engine Performance ◽  
Driving Cycle ◽  
Performance Characteristics ◽  
Pollutant Emission ◽  
Strong Impact ◽  
Light Duty ◽  
Light Duty Vehicles

The World-wide harmonised Light-duty Test Cycle (WLTC) was developed internationally for the determination of pollutant emission and fuel consumption from combustion engines of light-duty vehicles. It replaced the New European Driving Cycle (NEDC) used in the European Union (EU) for type-approval testing purposes. This paper presents an extensive comparison of the WLTC and NEDC. The main specifications of both driving cycles are provided, and their advantages and limitations are analysed. The WLTC, compared to the NEDC, is more dynamic, covers a broader spectrum of engine working states and is more realistic in simulating typical real-world driving conditions. The expected impact of the WLTC on vehicle engine performance characteristics is discussed. It is further illustrated by a case study on two light-duty vehicles tested in the WLTC and NEDC. Findings from the investigation demonstrated that the driving cycle has a strong impact on the performance characteristics of the vehicle combustion engine. For the vehicles tested, the average engine speed, engine torque and fuel flow rate measured over the WLTC are higher than those measured over the NEDC. The opposite trend is observed in terms of fuel economy (expressed in l/100 km); the first vehicle achieved a 9% reduction, while the second – a 3% increase when switching from NEDC to WLTC. Several factors potentially contributing to this discrepancy have been pointed out. The implementation of the WLTC in the EU will force vehicle manufacturers to optimise engine control strategy according to the operating range of the new driving cycle.

Ethers and esters as alternative fuels for internal combustion engine: A review

2021 ◽  
pp. 146808742110464
Author(s):  
Yang Hua
Keyword(s):  
Alternative Fuels ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Engine Performance ◽  
Internal Combustion ◽  
Operating Conditions ◽  
Future Research ◽  
Particulate Emissions ◽  
Ic Engine

Ether and ester fuels can work in the existing internal combustion (IC) engine with some important advantages. This work comprehensively reviews and summarizes the literatures on ether fuels represented by DME, DEE, DBE, DGM, and DMM, and ester fuels represented by DMC and biodiesel from three aspects of properties, production and engine application, so as to prove their feasibility and prospects as alternative fuels for compression ignition (CI) and spark ignition (SI) engines. These studies cover the effects of ether and ester fuels applied in the form of single fuel, mixed fuel, dual-fuel, and multi-fuel on engine performance, combustion and emission characteristics. The evaluation indexes mainly include torque, power, BTE, BSFC, ignition delay, heat release rate, pressure rise rate, combustion duration, exhaust gas temperature, CO, HC, NOx, PM, and smoke. The results show that ethers and esters have varying degrees of impact on engine performance, combustion and emissions. They can basically improve the thermal efficiency of the engine and reduce particulate emissions, but their effects on power, fuel consumption, combustion process, and CO, HC, and NOx emissions are uncertain, which is due to the coupling of operating conditions, fuel molecular structure, in-cylinder environment and application methods. By changing the injection strategy, adjusting the EGR rate, adopting a new combustion mode, adding improvers or synergizing multiple fuels, adverse effects can be avoided and the benefits of oxygenated fuel can be maximized. Finally, some challenges faced by alternative fuels and future research directions are analyzed.

Adaptive calibration of Diesel engine injection for minimising fuel consumption with constrained NOx emissions in actual driving missions

2020 ◽  
pp. 146808742091880
Author(s):  
José Manuel Luján ◽  
Benjamín Pla ◽  
Pau Bares ◽  
Varun Pandey
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Time Window ◽  
Transition Probability ◽  
Estimation Method ◽  
Engine Performance ◽  
Driving Cycle ◽  
Vehicle Speed ◽  
Adaptive Calibration ◽  
Emission Limits

This article proposes a method for fuel minimisation of a Diesel engine with constrained [Formula: see text] emission in actual driving mission. Specifically, the methodology involves three developments: The first is a driving cycle prediction tool which is based on the space-variant transition probability matrix obtained from an actual vehicle speed dataset. Then, a vehicle and an engine model is developed to predict the engine performance depending on the calibration for the estimated driving cycle. Finally, a controller is proposed which adapts the start-of-injection calibration map to fulfil the [Formula: see text] emission constraint while minimising the fuel consumption. The calibration is adapted during a predefined time window based on the predicted engine performance on the estimated cycle and the difference between the actual and the constraint on engine [Formula: see text] emissions. The method assessment was done experimentally in the engine test set-up. The engine performace using the method is compared with the state-of-the-art static calibration method for different [Formula: see text] emission limits on real driving cycles. The online implementation of the method shows that the fuel consumption can be reduced by 3%–4% while staying within the emission limits, indicating that the estimation method is able to capture the main driving cycle characterstics.

Control Systems for Automotive Vehicle Fuel Economy: A Literature Review

1981 ◽  
Vol 103 (3) ◽  
pp. 173-180 ◽  
Author(s):  
L. M. Sweet
Keyword(s):  
Control Systems ◽  
Combustion Engine ◽  
Control Strategies ◽  
Engine Performance ◽  
Type Systems ◽  
Open Loop ◽  
Feedback Systems ◽  
Fuel Flow ◽  
Loop Feedback ◽  
Hybrid Vehicle Control

This paper is a review of current research on applications of control systems and theory to achieve energy conservation in automotive vehicles. The development of internal combustion engine control systems that modulate fuel flow, air flow, ignition timing and duration, and exhaust gas recirculation is discussed. The relative advantages of physical and empirical models for engine performance are reviewed. Control strategies presented include optimized open-loop schedule type systems, closed-loop feedback systems, and adaptive controllers. The development of power train and hybrid vehicle control systems is presented, including controllers for both conventional transmissions and those employing flywheel energy storage.

scholarly journals Development of a Pattern Recognition Methodology with Thermography and Implementation in an Experimental Study of a Boiler for a WHRS-ORC

2019 ◽  
Author(s):  
Concepción Paz ◽  
Eduardo Suarez ◽  
Miguel Concheiro ◽  
Antonio Diaz
Keyword(s):  
Pattern Recognition ◽  
Wall Temperature ◽  
Waste Heat ◽  
Combustion Engine ◽  
Organic Rankine Cycle ◽  
Exhaust System ◽  
Rankine Cycle ◽  
Operating Conditions ◽  
Cycle Performance ◽  
Working Fluid

Waste heat dissipated in the exhaust system in a combustion engine represents a major source of energy to be recovered and converted into useful work. A waste heat recovery system (WHRS) based on an Organic Rankine Cycle (ORC) is a promising approach, and has gained interest in the last few years in an automotive industry interested in reducing fuel consumption and exhaust emissions. Understanding the thermodynamic response of the boiler employed in an ORC plays an important role in steam cycle performance prediction and control system design. The aim of this study is therefore to present a methodology to study these devices by means of pattern recognition with infrared thermography. In addition, the experimental test bench and its operating conditions are described. The methodology proposed identifies the wall coordinates, traces paths, and tracks wall temperature along them in a way that can be exported for subsequent post-processing and analysis. As for the results, through the wall temperature paths on both sides (exhaust gas and working fluid) it was possible to quantitatively estimate the temperature evolution along the boiler and, in particular, the beginning and end of evaporation.

Sign in / Sign up

Export Citation Format

Share Document