Investigation on Cooling Effectiveness and Flow Resistance of Inlet Fogging Location in Gas Turbine Inlet Duct

2015 ◽  
Author(s):  
Hai Zhang ◽  
Bin Jiang ◽  
Qun Zheng ◽  
Mustapha Chaker
Keyword(s):  
Pressure Drop ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Flow Resistance ◽  
Cost Effective ◽  
Cooling Effect ◽  
Injection Velocity ◽  
Inlet Temperature ◽  
Turbine Inlet ◽  
Inlet Duct

The output power and efficiency of gas turbines are reduced significantly during the hot weather, particularly in areas where the daytime temperature reaches as high as 50 °C. Gas turbine inlet fogging and overspray has been considered a efficient and cost-effective method to augment the power output. Therefore, the evaporation effect and the flow resistance performance in the inlet duct after the inlet fogging applied are the objectives of this paper. The nozzles array mounted on channels and beams, and they have effects on the pressure drop. Installation site of the fogging nozzles which is relative to the silencers also have impact on the effectiveness of evaporation and cooling. For research the evaporative cooling effect in the duct, the whole inlet duct is meshed in this research to compute the pressure drop through the nozzles frames under fogging and none-fogging conditions with CFD method. The results indicate that injection velocity and arrangement of nozzles have significant effects on the pressure drops and cooling effect, which will affect compressor performance. Gas turbine is sensitive not only to the inlet temperature, but also to the inlet pressure drop. This paper provides a comprehensive analysis of the pressure drop and evaporation of inlet fogging and will be of values to gas turbine inlet fogging system designers and users.

Numerical Analysis of Gas Turbine Inlet Fogging Nozzle Manifold Pressure Drop

2014 ◽  
Author(s):  
Hai Zhang ◽  
Qun Zheng ◽  
Mustapha Chaker ◽  
Cyrus Meher-Homji
Keyword(s):  
Pressure Drop ◽  
Gas Turbine ◽  
Flow Resistance ◽  
Research Effort ◽  
Water Injection ◽  
Injection Velocity ◽  
Injection Angle ◽  
Turbine Inlet ◽  
Area Of Concern ◽  
Inlet Duct

The air pressure drop over the nozzles manifolds of inlet fogging system and the flow resistance downstream of the nozzle array (manifold) have always been an area of concern and is the object of this paper. Fogging nozzles arrays (involving several hundred nozzles) are mounted on channels and beams, downstream of the inlet filters and affect the pressure drop. The water injection angle, nozzle injection velocities and the progressive evaporation of the water droplets evaporation all influence the inlet pressure seen at the gas turbine inlet. This paper focuses on a numerical simulation investigation of flow resistance (pressure drop) of inlet fogging systems. In this research effort, the inlet duct is meshed in order to compute the pressure drop over the nozzles frames in fogging and non-fogging conditions. First, the resistance coefficients of an air intake filter are obtained by numerical and experimental methods, and then the coefficients are used for the simulation of the inlet duct by considering the filter as a porous media. Effects of nozzle spread pattern and water injection pattern are then modeled. The results indicate that injection velocity and arrangement of nozzles could have significant effects on the pressure drop and intake distortion, which will affect compressor performance. This paper provides a comprehensive analysis of the pressure drop and evaporation of inlet fogging and will be of value to gas turbine inlet fogging system designers and users.

Rolls Royce/Allison 501-K Gas Turbine Anti-Fouling Compressor Coatings Evaluation

2002 ◽  
Author(s):  
Daniel E. Caguiat
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Gas Turbines ◽  
Performance Degradation ◽  
Specific Fuel Consumption ◽  
Inlet Temperature ◽  
Test Results ◽  
Turbine Inlet ◽  
Compressor Performance ◽  
Compressor Efficiency

The Naval Surface Warfare Center, Carderock Division (NSWCCD) Gas Turbine Emerging Technologies Code 9334 was tasked by NSWCCD Shipboard Energy Office Code 859 to research and evaluate fouling resistant compressor coatings for Rolls Royce Allison 501-K Series gas turbines. The objective of these tests was to investigate the feasibility of reducing the rate of compressor fouling degradation and associated rate of specific fuel consumption (SFC) increase through the application of anti-fouling coatings. Code 9334 conducted a market investigation and selected coatings that best fit the test objective. The coatings selected were Sermalon for compressor stages 1 and 2 and Sermaflow S4000 for the remaining 12 compressor stages. Both coatings are manufactured by Sermatech International, are intended to substantially decrease blade surface roughness, have inert top layers, and contain an anti-corrosive aluminum-ceramic base coat. Sermalon contains a Polytetrafluoroethylene (PTFE) topcoat, a substance similar to Teflon, for added fouling resistance. Tests were conducted at the Philadelphia Land Based Engineering Site (LBES). Testing was first performed on the existing LBES 501-K17 gas turbine, which had a non-coated compressor. The compressor was then replaced by a coated compressor and the test was repeated. The test plan consisted of injecting a known amount of salt solution into the gas turbine inlet while gathering compressor performance degradation and fuel economy data for 0, 500, 1000, and 1250 KW generator load levels. This method facilitated a direct comparison of compressor degradation trends for the coated and non-coated compressors operating with the same turbine section, thereby reducing the number of variables involved. The collected data for turbine inlet, temperature, compressor efficiency, and fuel consumption were plotted as a percentage of the baseline conditions for each compressor. The results of each plot show a decrease in the rates of compressor degradation and SFC increase for the coated compressor compared to the non-coated compressor. Overall test results show that it is feasible to utilize anti-fouling compressor coatings to reduce the rate of specific fuel consumption increase associated with compressor performance degradation.

scholarly journals Cooling and Sealing Air System in Industrial Gas Turbine Engines

1996 ◽  
Author(s):  
A. W. Reichert ◽  
M. Janssen
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Gas Turbines ◽  
State Of The Art ◽  
Cooling System ◽  
Inlet Temperature ◽  
Turbine Inlet ◽  
Air System ◽  
Calculation System ◽  
Cooling Air

Siemens heavy duty Gas Turbines have been well known for their high power output combined with high efficiency and reliability for more than 3 decades. Offering state of the art technology at all times, the requirements concerning the cooling and sealing air system have increased with technological development over the years. In particular the increase of the turbine inlet temperature and reduced NOx requirements demand a highly efficient cooling and sealing air system. The new Vx4.3A family of Siemens gas turbines with ISO turbine inlet temperatures of 1190°C in the power range of 70 to 240 MW uses an effective film cooling technique for the turbine stages 1 and 2 to ensure the minimum cooling air requirement possible. In addition, the application of film cooling enables the cooling system to be simplified. For example, in the new gas turbine family no intercooler and no cooling air booster for the first turbine vane are needed. This paper deals with the internal air system of Siemens gas turbines which supplies cooling and sealing air. A general overview is given and some problems and their technical solutions are discussed. Furthermore a state of the art calculation system for the prediction of the thermodynamic states of the cooling and sealing air is introduced. The calculation system is based on the flow calculation package Flowmaster (Flowmaster International Ltd.), which has been modified for the requirements of the internal air system. The comparison of computational results with measurements give a good impression of the high accuracy of the calculation method used.

Expanding Fuel Flexibility in MHPS’ Dry Low NOx Combustor

2018 ◽  
Author(s):  
Katsuyoshi Tada ◽  
Kei Inoue ◽  
Tomo Kawakami ◽  
Keijiro Saitoh ◽  
Satoshi Tanimura
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Environmental Conservation ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Social Perspectives ◽  
Turbine Inlet ◽  
Fuel Flexibility

Gas-turbine combined-cycle (GTCC) power generation is clean and efficient, and its demand will increase in the future from economic and social perspectives. Raising turbine inlet temperature is an effective way to increase combined cycle efficiency and contributes to global environmental conservation by reducing CO2 emissions and preventing global warming. However, increasing turbine inlet temperature can lead to the increase of NOx emissions, depletion of the ozone layer and generation of photochemical smog. To deal with this issue, MHPS (MITSUBISHI HITACHI POWER SYSTEMS) and MHI (MITSUBISHI HEAVY INDUSTRIES) have developed Dry Low NOx (DLN) combustion techniques for high temperature gas turbines. In addition, fuel flexibility is one of the most important features for DLN combustors to meet the requirement of the gas turbine market. MHPS and MHI have demonstrated DLN combustor fuel flexibility with natural gas (NG) fuels that have a large Wobbe Index variation, a Hydrogen-NG mixture, and crude oils.

Off-design performance improvement of twin-shaft gas turbine by variable geometry turbine and compressor besides fuel control

2019 ◽  
Vol 234 (7) ◽  
pp. 957-980
Author(s):  
Sepehr Sanaye ◽  
Salahadin Hosseini
Keyword(s):  
Life Cycle ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Guide Vane ◽  
Design Parameters ◽  
Inlet Guide Vane ◽  
Inlet Temperature ◽  
Gas Generator ◽  
Turbine Inlet ◽  
Exit Temperature

A novel procedure for finding the optimum values of design parameters of industrial twin-shaft gas turbines at various ambient temperatures is presented here. This paper focuses on being off design due to various ambient temperatures. The gas turbine modeling is performed by applying compressor and turbine characteristic maps and using thermodynamic matching method. The gas turbine power output is selected as an objective function in optimization procedure with genetic algorithm. Design parameters are compressor inlet guide vane angle, turbine exit temperature, and power turbine inlet nozzle guide vane angle. The novel constrains in optimization are compressor surge margin and turbine blade life cycle. A trained neural network is used for life cycle estimation of high pressure (gas generator) turbine blades. Results for optimum values for nozzle guide vane/inlet guide vane (23°/27°–27°/6°) in ambient temperature range of 25–45 ℃ provided higher net power output (3–4.3%) and more secured compressor surge margin in comparison with that for gas turbines control by turbine exit temperature. Gas turbines thermal efficiency also increased from 0.09 to 0.34% (while the gas generator turbine first rotor blade creep life cycle was kept almost constant about 40,000 h). Meanwhile, the averaged values for turbine exit temperature/turbine inlet temperature changed from 831.2/1475 to 823/1471°K, respectively, which shows about 1% decrease in turbine exit temperature and 0.3% decrease in turbine inlet temperature.

Recent Advances of Internal Cooling Techniques for Gas Turbine Airfoils

2013 ◽  
Vol 5 (2) ◽  
Author(s):  
Minking K. Chyu ◽  
Sin Chien Siw
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Energy Demand ◽  
Major Elements ◽  
Inlet Temperature ◽  
Internal Cooling ◽  
Performance Goal ◽  
Turbine Inlet Temperature ◽  
Air Breathing ◽  
Turbine Inlet

The performance goal of modern gas turbine engines, both land-base and air-breathing engines, can be achieved by increasing the turbine inlet temperature (TIT). The level of TIT in the near future can reach as high as 1700 °C for utility turbines and over 1900 °C for advanced military engines. Advanced and innovative cooling techniques become one of the crucial major elements supporting the development of modern gas turbines, both land-based and air-breathing engines with continual increment of turbine inlet temperature (TIT) in order to meet higher energy demand and efficiency. This paper discusses state-of-the-art airfoil cooling techniques that are mainly applicable in the mainbody and trailing edge section of turbine airfoil. Potential internal cooling designs for near-term applications based on current manufacturing capabilities are identified. A literature survey focusing primarily on the past four to five years has also been performed.

Status of the Automotive Ceramic Gas Turbine Development Progrem: Year Four Progress

1995 ◽  
Author(s):  
Tsubura Nishiyama ◽  
Masumi Iwai ◽  
Norio Nakazawa ◽  
Masafumi Sasaki ◽  
Haruo Katagiri ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Inlet Temperature ◽  
Rotor Speed ◽  
Turbine Inlet Temperature ◽  
Turbine Engine ◽  
Turbine Inlet ◽  
Basic Engine ◽  
Energy Center ◽  
Engine Components

The seven-year program, designated “Research & Development of Automotive Ceramic Gas Turbine Engine (CGT Program)”, was started in 1990 with the object of demonstrating the advantageous potentials of ceramic gas turbines for automotive use. This CGT Program is conducted by Petroleum Energy Center. The basic engine is a 100kW, single-shaft regenerative engine having turbine inlet temperature of 1350°C and rotor speed of 110000rpm. In the forth year of the program, the engine components were experimentally evaluated and improved in the various test rigs, and the first assembly test including rotating and stationary components, was performed this year under the condition of turbine inlet temperature of 1200°C.

scholarly journals Exergy Efficiency Optimization for Gas Turbine Based Cogeneration Systems

2013 ◽  
Author(s):  
Ana C. Ferreira ◽  
Senhorinha F. Teixeira ◽  
José C. Teixeira ◽  
Manuel L. Nunes ◽  
Luís B. Martins
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Exergy Analysis ◽  
Exergy Efficiency ◽  
Plant Performance ◽  
System Component ◽  
Inlet Temperature ◽  
Exergy Destruction ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet

Energy degradation can be calculated by the quantification of entropy and loss of work and is a common approach in power plant performance analysis. Information about the location, amount and sources of system deficiencies are determined by the exergy analysis, which quantifies the exergy destruction. Micro-gas turbines are prime movers that are ideally suited for cogeneration applications due to their flexibility in providing stable and reliable power. This paper presents an exergy analysis by means of a numerical simulation of a regenerative micro-gas turbine for cogeneration applications. The main objective is to study the best configuration of each system component, considering the minimization of the system irreversibilities. Each component of the system was evaluated considering the quantitative exergy balance. Subsequently the optimization procedure was applied to the mathematical model that describes the full system. The rate of irreversibility, efficiency and flaws are highlighted for each system component and for the whole system. The effect of turbine inlet temperature change on plant exergy destruction was also evaluated. The results disclose that considerable exergy destruction occurs in the combustion chamber. Also, it was revealed that the exergy efficiency is expressively dependent on the changes of the turbine inlet temperature and increases with the latter.

Redesign of the TG20 Heavy-Duty Gas Turbine to Increase Turbine Inlet Temperature and Global Efficiency

2020 ◽  
Author(s):  
Mirko Baratta ◽  
Francesco Cardile ◽  
Daniela Anna Misul ◽  
Nicola Rosafio ◽  
Simone Salvadori ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Coolant Fluid ◽  
Specific Power ◽  
Inlet Temperature ◽  
Heavy Duty ◽  
Turbine Inlet Temperature ◽  
Rotating Blade ◽  
Turbine Inlet ◽  
Heavy Duty Gas Turbine

Abstract The even more stringent limitations set by the European Commission on pollutant emissions are forcing gas turbine manufacturers towards the redesign of the most important components to increase efficiency and specific power. Current trends in gas turbine design include an increased attention to the design of cooling systems and enhanced best practices for the study of components interaction. At the same time, the recent crisis suffered by the oil and gas industry reduced the interest in brand new gas turbines, thus increasing the service market. Therefore, original equipment manufacturers would rather propose the replacement of specific components within the gas turbine plant during its maintenance with compatible elements that are likely to guarantee increased performance and longer residual lifetime at a more desirable nominal working point. In the present activity the cooling system of the TG20 heavy-duty gas turbine has been redesigned to increase the turbine inlet temperature while contemporaneously reducing the total amount of coolant mass-flow. Specifically, the cooling scheme of the rotating blade of the first turbine row has been reviewed at the Department of Energy (DENERG) of Politecnico di Torino in cooperation with EthosEnergy Italia S.p.a.. The paper presents a new design, which, starting from the original solution featuring fifteen smooth pipes, adopts an improved geometry characterized by the presence of turbulators. The activity has been carried out using Computational Fluid Dynamics (CFD) for the coolant/blade interaction and one-dimensional models developed at EthosEnergy for the redistribution of the cooling flows in the cavities. The mutual effects between the coolant fluid and the blade are analyzed using a Conjugate Heat Transfer (CHT) approach with Star-CCM+. The validation of the computational approach has been performed exploiting the experimental data available for the NASA C3X test case. The TG20 rotating blade of the first turbine row has been analyzed considering the two different coolant configurations. The impact of the main flow on the thermal field has initially been included by imposing a temperature field on the blade surface. The latter field has in turn been obtained by means of a separate computation for the solid only. Full CHT simulations has hence been performed, thus quantifying the accuracy of the proposed approach. The obtained results are discussed in terms of thermo-fluid-dynamic effects.

scholarly journals Optimum Power Boosting of Gas Turbine Cycles With Refrigerated Inlet Air and Compressor Intercooling

1996 ◽  
Author(s):  
Mohand A. Ait-Ali
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Turbine Blade Cooling ◽  
High Pressure Ratio ◽  
Blade Cooling ◽  
Air Inlet ◽  
Turbine Inlet ◽  
Compressor Work

With or without turbine blade cooling, gas turbine cycles have consistently higher turbine inlet temperatures than steam turbine cycles. But this advantage is more than offset by the excessive compressor work induced by warm inlet temperatures, particularly during operation on hot summer days. Instead of seeking still higher turbine inlet temperatures by means of sophisticated blade cooling technology and high temperature-resistant blade materials, it is proposed to greatly increase the cycle net work and also improve thermal efficiency by decreasing the compressor work. This is obtained by using refrigerated inlet air and compressor intercooling to an extent which optimizes the refrigerated air inlet temperature and consequently the gas turbine compression ratio with respect to maximum specific net power. The cost effectiveness of this conceptual cycle, which also includes regeneration, has not been examined in this paper as it requires unusually high pressure ratio gas turbines and compressors, as well as high volumetric air flow rate and low temperature refrigeration equipment for which reliable cost data is not easily available.

Sign in / Sign up

Export Citation Format

Share Document