Analysis of the Influence of Pilot Injection Timing on Diesel Combustion in an Optical Engine by the Two-Color Method

2013 ◽  
Author(s):  
Weilin Zeng ◽  
Xu He ◽  
Senjia Jin ◽  
Hai Liu ◽  
Xiangrong Li ◽  
...  
Keyword(s):  
Ignition Delay ◽  
High Speed ◽  
Fuel Injection ◽  
Injection System ◽  
High Speed Photography ◽  
Injection Timing ◽  
Pilot Injection ◽  
Diesel Combustion ◽  
Optical Engine ◽  
Combustion Duration

High-speed photography, two-color method, and thermodynamic analysis have been used to improve understanding of the influence of pilot injection timing on diesel combustion in an optical engine equipped with an electronically-controlled, common rail, high-pressure fuel injection system. The tests were performed at four different pilot injection timings (30 degree, 25 degree, 20 degree, and 15 degree CA BTDC) with the same main injection timing (5 degree CA BTDC), and under 100MPa injection pressure. The engine speed was selected at 1200 rev/min, and the whole injection mass was fixed as 27.4 mg/stroke. The experimental results showed that the pilot injection timing had a strong influence on ignition delay and combustion duration: advancing the pilot injection timing turned to prolong the ignition delay and shorten the combustion duration. The combustion images indicated that when pilot injection was advanced, the area of luminous flames decreased. The results of two-color method suggested pilot injection timing significantly impacted both the soot temperature distribution and soot concentration (KL factor) within the combustion chamber. 30 degree CA BTDC was the optimal pilot injection timing for in-cylinder soot reduction.

An experimental analysis of low-temperature and premixed combustion for simultaneous reduction of NOx and particulate emissions in direct injection diesel engines

2002 ◽  
Vol 3 (4) ◽  
pp. 249-259 ◽  
Author(s):  
S Kimura ◽  
H Ogawa ◽  
Y Matsui ◽  
Y Enomoto
Keyword(s):  
Low Temperature ◽  
Thermal Efficiency ◽  
Ignition Delay ◽  
High Speed ◽  
Fuel Injection ◽  
Premixed Combustion ◽  
High Speed Photography ◽  
Injection Timing ◽  
Particulate Emissions ◽  
Injection Duration

A new combustion concept, named MK (modulated kinetics) combustion, has been developed, which reduces NOx and smoke simultaneously through high exhaust gas recirculation (EGR) and retarded injection timing. High-speed photography was employed to investigate the physical and chemical processes of MK combustion, and the results revealed that the combustion features premixed combustion and the low-temperature flames were accompanied by transparent appearances. Heat flux measurements and KIVA calculations were also made to investigate the effects of swirl, which serves to improve thermal efficiency in MK combustion. It was apparent that the swirl effectively governs the fuel distribution in the combustion chamber, suppressing HC formation and improving thermal efficiency by preventing the flames from contacting the cavity walls. Throughout these experiments, ignition delay and fuel injection duration were found to be the two key parameters that control MK combustion. Accordingly, ignition delay was prolonged by cooled EGR and fuel injection duration was shortened by high injection pressure to allow the MK combustion operation in a high load range.

An Experimental Investigation of the Effects of Common-Rail Injection System Parameters on Emissions and Performance in a High-Speed Direct-Injection Diesel Engine

1999 ◽  
Vol 123 (1) ◽  
pp. 167-174 ◽  
Author(s):  
P. J. Tennison ◽  
R. Reitz
Keyword(s):  
Diesel Engine ◽  
High Speed ◽  
Direct Injection ◽  
Injection Pressure ◽  
Injection System ◽  
Injection Timing ◽  
Pilot Injection ◽  
Common Rail Injection System ◽  
And Performance ◽  
Emissions And Performance

An investigation of the effect of injection parameters on emissions and performance in an automotive diesel engine was conducted. A high-pressure common-rail injection system was used with a dual-guided valve covered orifice nozzle tip. The engine was a four-valve single cylinder high-speed direct-injection diesel engine with a displacement of approximately 12 liter and simulated turbocharging. The engine experiments were conducted at full load and 1004 and 1757 rev/min, and the effects of injection pressure, multiple injections (single vs pilot with main), and pilot injection timing on emissions and performance were studied. Increasing the injection pressure from 600 to 800 bar reduced the smoke emissions by over 50 percent at retarded injection timings with no penalty in oxides of nitrogen NOx or brake specific fuel consumption (BSFC). Pilot injection cases exhibited slightly higher smoke levels than single injection cases but had similar NOx levels, while the single injection cases exhibited slightly better BSFC. The start-of-injection (SOI) of the pilot was varied while holding the main SOI constant and the effect on emissions was found to be small compared to changes resulting from varying the main injection timing. Interestingly, the point of autoignition of the pilot was found to occur at a nearly constant crank angle regardless of pilot injection timing (for early injection timings) indicating that the ignition delay of the pilot is a chemical delay and not a physical (mixing) one. As the pilot timing was advanced the mixture became overmixed, and an increase of over 50 percent in the unburned hydrocarbon emissions was observed at the most advanced pilot injection timing.

scholarly journals Effect of Premixed Fuel Preparation for Partially Premixed Combustion With a Low Octane Gasoline on a Light-Duty Multicylinder Compression Ignition Engine

2015 ◽  
Vol 137 (11) ◽  
Author(s):  
Adam B. Dempsey ◽  
Scott Curran ◽  
Robert Wagner ◽  
William Cannella
Keyword(s):  
High Pressure ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Premixed Combustion ◽  
Injection System ◽  
Injection Timing ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Partially Premixed Combustion ◽  
Injection Strategies

Gasoline compression ignition (GCI) concepts with the majority of the fuel being introduced early in the cycle are known as partially premixed combustion (PPC). Previous research on single- and multicylinder engines has shown that PPC has the potential for high thermal efficiency with low NOx and soot emissions. A variety of fuel injection strategies have been proposed in the literature. These injection strategies aim to create a partially stratified charge to simultaneously reduce NOx and soot emissions while maintaining some level of control over the combustion process through the fuel delivery system. The impact of the direct injection (DI) strategy to create a premixed charge of fuel and air has not previously been explored, and its impact on engine efficiency and emissions is not well understood. This paper explores the effect of sweeping the direct injected pilot timing from −91 deg to −324 deg ATDC, which is just after the exhaust valve closes (EVCs) for the engine used in this study. During the sweep, the pilot injection consistently contained 65% of the total fuel (based on command duration ratio), and the main injection timing was adjusted slightly to maintain combustion phasing near top dead center. A modern four cylinder, 1.9 l diesel engine with a variable geometry turbocharger (VGT), high pressure common rail injection system, wide included angle injectors, and variable swirl actuations was used in this study. The pistons were modified to an open bowl configuration suitable for highly premixed combustion modes. The stock diesel injection system was unmodified, and the gasoline fuel was doped with a lubricity additive to protect the high pressure fuel pump and the injectors. The study was conducted at a fixed speed/load condition of 2000 rpm and 4.0 bar brake mean effective pressure (BMEP). The pilot injection timing sweep was conducted at different intake manifold pressures, swirl levels, and fuel injection pressures. The gasoline used in this study has relatively high fuel reactivity with a research octane number of 68. The results of this experimental campaign indicate that the highest brake thermal efficiency (BTE) and lowest emissions are achieved simultaneously with the earliest pilot injection timings (i.e., during the intake stroke).

scholarly journals Investigation into the effect of different fuels on ignition delay of M-type diesel combustion process

2008 ◽  
Vol 12 (1) ◽  
pp. 103-114 ◽  
Author(s):  
Dzevad Bibic ◽  
Ivan Filipovic ◽  
Ales Hribernik ◽  
Boran Pikula
Keyword(s):  
Diesel Engine ◽  
Ignition Delay ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Process ◽  
Injection System ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Injection Angle ◽  
Start Of Injection

An ignition delay is a very complex process which depends on a great number of parameters. In practice, definition of the ignition delay is based on the use of correlation expressions. However, the correlation expressions have very often limited application field. This paper presents a new correlation which has been developed during the research project on the direct injection M-type diesel engine using both the diesel and biodiesel fuel, as well as different values of a static injection timing. A dynamic start of injection, as well as the ignition delay, is defined in two ways. The first approach is based on measurement of a needle lift, while the second is based on measurement of a fuel pressure before the injector. The latter approach requires calculation of pressure signals delay through the fuel injection system and the variation of a static advance injection angle changing. The start of a combustion and the end of the ignition delay is defined on the basis of measurements of an in-cylinder pressure and its point of separation from a skip-fire pressure trace. The developed correlation gives better prediction of the ignition delay definition for the M-type direct injection diesel engine in the case of diesel and biodiesel fuel use when compared with the classic expression by the other authors available in the literature.

scholarly journals MATHEMATICAL MODELLING OF INDICATIVE PROCESS PARAMETERS OF DUAL-FUEL ENGINES WITH CONVENTIONAL FUEL INJECTION SYSTEM

Transport ◽  
2020 ◽  
Vol 35 (1) ◽  
pp. 57-67 ◽  
Author(s):  
Sergejus Lebedevas ◽  
Saugirdas Pukalskas ◽  
Vygintas Daukšys
Keyword(s):  
High Speed ◽  
Fuel Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Second Phase ◽  
Injection Timing ◽  
Fuel Injection System ◽  
One Dimensional ◽  
Motor Test ◽  
Conventional Fuel

Modern engine research uses multi-dimensional Mathematical Models (MMs) that are applicable to multi-fuel engines. However, their use involves the availability of detailed technical data on the design and characteristics of the engine, which is not always possible. The use of a one-dimensional MM is more expedient for the prediction of engine parameters, but their application for this purpose has not yet been sufficiently investigated. This publication presents the results of numerical studies evaluating the application of a one-dimensional MM with bi-phase Vibe combustion laws for dual-fuel (DF) Diesel (D) and Natural Gas (NG) engine power parameters. The motor test results of a high-speed 4ČN79.5/95.5 Diesel Engine (DE) with a conventional fuel injection system were used as adequacy criteria. The engines were operated with D100 and DF D20/NG80, in high- (HLM), medium- (MLM), and low- (LLM) load modes, and the angle of Diesel-fuel Injection Timing (DIT) was changed from −1 to −13 °CA in the Before Top Dead Center (BTDC) range. Modelling of the single-phase Vibe combustion law has limited applicability for efficient use only in HLM (with an error of 7%). In the MLM and LLM regimes, owing to non-compliance with real bi-phasic combustion with a strongly extended NG diffusive second phase, the modelling error is 50%. Individual MM matching in MLM and LLM in a DF D20/NG80 experiment detected a burn time increase from between 45 and 50 °CA, to 110 and 200 °CA, respectively. Limited use of the one-dimensional MM in the evaluation of DF engine performance has been identified. When comparing a one-dimensional MM with experimental data, a bi-phase law of heat release characteristic should be considered for better coincidence. In addition, individual MM matching with an experiment on each engine load mode ensured acceptable accuracy in testing and optimising the parameters of the indicator process, including DIT.

scholarly journals Effect of Premixed Fuel Preparation for Partially Premixed Combustion With a Low Octane Gasoline on a Light-Duty Multi-Cylinder Compression Ignition Engine

2014 ◽  
Author(s):  
Adam Dempsey ◽  
Scott Curran ◽  
Robert Wagner ◽  
William Cannella
Keyword(s):  
High Pressure ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Premixed Combustion ◽  
Injection System ◽  
Injection Timing ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Partially Premixed Combustion ◽  
Injection Strategies

Gasoline compression ignition concepts with the majority of the fuel being introduced early in the cycle are known as partially premixed combustion (PPC). Previous research on single- and multi-cylinder engines has shown that PPC has the potential for high thermal efficiency with low NOx and soot emissions. A variety of fuel injection strategies has been proposed in the literature. These injection strategies aim to create a partially stratified charge to simultaneously reduce NOx and soot emissions while maintaining some level of control over the combustion process through the fuel delivery system. The impact of the direct injection strategy to create a premixed charge of fuel and air has not previously been explored, and its impact on engine efficiency and emissions is not well understood. This paper explores the effect of sweeping the direct injected pilot timing from −91° to −324° ATDC, which is just after the exhaust valve closes for the engine used in this study. During the sweep, the pilot injection consistently contained 65% of the total fuel (based on command duration ratio), and the main injection timing was adjusted slightly to maintain combustion phasing near top dead center. A modern four cylinder, 1.9 L diesel engine with a variable geometry turbocharger, high pressure common rail injection system, wide included angle injectors, and variable swirl actuation was used in this study. The pistons were modified to an open bowl configuration suitable for highly premixed combustion modes. The stock diesel injection system was unmodified, and the gasoline fuel was doped with a lubricity additive to protect the high pressure fuel pump and the injectors. The study was conducted at a fixed speed/load condition of 2000 rpm and 4.0 bar brake mean effective pressure (BMEP). The pilot injection timing sweep was conducted at different intake manifold pressures, swirl levels, and fuel injection pressures. The gasoline used in this study has relatively high fuel reactivity with a research octane number of 68. The results of this experimental campaign indicate that the highest brake thermal efficiency and lowest emissions are achieved simultaneously with the earliest pilot injection timings (i.e., during the intake stroke).

Effect of Injection Timing on Combustion Characteristics of a DI Diesel Engine Fuelled with Pistacia chinensis Bunge Seed Biodiesel

2012 ◽  
Vol 614-615 ◽  
pp. 337-342
Author(s):  
Li Luo ◽  
Bin Xu ◽  
Zhi Hao Ma ◽  
Jian Wu ◽  
Ming Li
Keyword(s):  
Combustion Temperature ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Brake Specific Fuel Consumption ◽  
Cylinder Pressure ◽  
Combustion Duration ◽  
Di Diesel Engine ◽  
Maximum Combustion Temperature

In this study, the effect of injection timing on combustion characteristics of a direct injection, electronically controlled, high pressure, common rail, turbocharged and intercooled engine fuelled with different pistacia chinensis bunge seed biodiesel/diesel blends has been experimentally investigated. The results indicated that brake specific fuel consumption reduces with the increasing of fuel injection advance angle and enhances with the increasing of biodiesel content in the blends. The peak of cylinder pressure and maximum combustion temperature increase evidently with the increment of fuel injection advance angle. However, the combustion of biodiesel blends starts earlier than diesel at the same fuel injection advance angle. At both conditions, the combustion duration and the peak of heat release rate are insensitive to the changing of injection timing.

scholarly journals Influence of the diesel pilot injector configuration on ethanol combustion and performance of a heavy-duty direct injection engine

2021 ◽  
pp. 146808742110012
Author(s):  
Nicola Giramondi ◽  
Anders Jäger ◽  
Daniel Norling ◽  
Anders Christiansen Erlandsson
Keyword(s):  
Direct Injection ◽  
Engine Performance ◽  
High Load ◽  
Operating Conditions ◽  
Injection System ◽  
Injection Timing ◽  
Diesel Combustion ◽  
Heavy Duty ◽  
Pure Ethanol ◽  
Ethanol Combustion

Thanks to its properties and production pathways, ethanol represents a valuable alternative to fossil fuels, with potential benefits in terms of CO2, NOx, and soot emission reduction. The resistance to autoignition of ethanol necessitates an ignition trigger in compression-ignition engines for heavy-duty applications, which in the current study is a diesel pilot injection. The simultaneous direct injection of pure ethanol as main fuel and diesel as pilot fuel through separate injectors is experimentally investigated in a heavy-duty single cylinder engine at a low and a high load point. The influence of the nozzle hole number and size of the diesel pilot injector on ethanol combustion and engine performance is evaluated based on an injection timing sweep using three diesel injector configurations. The tested configurations have the same geometric total nozzle area for one, two and four diesel sprays. The relative amount of ethanol injected is swept between 78 – 89% and 91 – 98% on an energy basis at low and high load, respectively. The results show that mixing-controlled combustion of ethanol is achieved with all tested diesel injector configurations and that the maximum combustion efficiency and variability levels are in line with conventional diesel combustion. The one-spray diesel injector is the most robust trigger for ethanol ignition, as it allows to limit combustion variability and to achieve higher combustion efficiencies compared to the other diesel injector configurations. However, the two- and four-spray diesel injectors lead to higher indicated efficiency levels. The observed difference in the ethanol ignition dynamics is evaluated and compared to conventional diesel combustion. The study broadens the knowledge on ethanol mixing-controlled combustion in heavy-duty engines at various operating conditions, providing the insight necessary for the optimization of the ethanol-diesel dual-injection system.

scholarly journals Performance evaluation of common rail direct injection (CRDI) engine fuelled with Uppage Oil Methyl Ester (UOME)

2015 ◽  
Vol 4 (1) ◽  
pp. 1-10 ◽  
Author(s):  
D.N. Basavarajappa ◽  
N. R. Banapurmath ◽  
S.V. Khandal ◽  
G. Manavendra
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Engines ◽  
High Speed ◽  
Alternative Fuels ◽  
High Pressures ◽  
Fuel Injection ◽  
Injection Timing ◽  
Engine Operation ◽  
Performance And Emission

For economic and social development of any country energy is one of the most essential requirements. Continuously increasing price of crude petroleum fuels in the present days coupled with alarming emissions and stringent emission regulations has led to growing attention towards use of alternative fuels like vegetable oils, alcoholic and gaseous fuels for diesel engine applications. Use of such fuels can ease the burden on the economy by curtailing the fuel imports. Diesel engines are highly efficient and the main problems associated with them is their high smoke and NOx emissions.  Hence there is an urgent need to promote the use of alternative fuels in place of high speed diesel (HSD) as substitute. India has a large agriculture base that can be used as a feed stock to obtain newer fuel which is renewable and sustainable. Accordingly Uppage oil methyl ester (UOME) biodiesel was selected as an alternative fuel. Use of biodiesels in diesel engines fitted with mechanical fuel injection systems has limitation on the injector opening pressure (300 bar). CRDI system can overcome this drawback by injecting fuel at very high pressures (1500-2500 bar) and is most suitable for biodiesel fuels which are high viscous. This paper presents the performance and emission characteristics of a CRDI diesel engine fuelled with UOME biodiesel at different injection timings and injection pressures. From the experimental evidence it was revealed that UOME biodiesel yielded overall better performance with reduced emissions at retarded injection timing of -10° BTDC in CRDI mode of engine operation.

Sign in / Sign up

Export Citation Format

Share Document