The Design Tradeoffs of Linear Functionally Graded Piezoceramic Actuators

Aerospace ◽  
2003 ◽  
Author(s):  
Paul W. Alexander ◽  
Diann Brei
Keyword(s):  
Material Properties ◽  
High Stress ◽  
Functionally Graded ◽  
Homogeneous Material ◽  
Stress Concentrations ◽  
Practical Applications ◽  
Complex Electric Field ◽  
Design Tradeoffs ◽  
A Minor ◽  
The Cost

It is common practice to reduce the voltage level within piezoelectric actuators by utilizing multiple layers, typically bonded together. Unfortunately, this has a tendency to result in device failure due to delamination. For example, with benders the typical lifetime is 105 to 106 cycles, limiting its use in practical applications. This poses an interesting design tradeoff: the stroke is increased due to sharper gradients between material layers; however, the higher gradients lead to high stress concentrations at those interfaces. One approach to reducing these stresses is to grade the material properties through a monolithic piece of piezoceramic so that no interfaces or bonding elements exist, but this comes at the cost of stroke. This paper explores the design tradeoff inherent to monolithic functionally graded piezoelectrics. An analytical free-displacement model for a monolithic piezoceramic beam with a generic gradient is derived. Key to this is the inclusion of the complex electric field distribution which rises from the non-homogeneous material properties. This model is used along with finite element models to examine the effect of continuous linear and stepwise material gradients on the displacement performance as well as the stress levels. The study shows that using monolithic functionally graded piezocermics can significantly reduce the stresses with only a minor impact on the device stroke.

scholarly journals A state-based peridynamic formulation for functionally graded Kirchhoff plates

2020 ◽  
pp. 108128652096338
Author(s):  
Zhenghao Yang ◽  
Erkan Oterkus ◽  
Selda Oterkus
Keyword(s):  
Material Properties ◽  
Lagrange Equation ◽  
Equations Of Motion ◽  
Functionally Graded ◽  
Benchmark Problems ◽  
Transverse Loading ◽  
Stress Concentrations ◽  
Element Analysis ◽  
Kirchhoff Plates ◽  
Peridynamic Model

Functionally graded materials are a potential alternative to traditional fibre-reinforced composite materials as they have continuously varying material properties which do not cause stress concentrations. In this study, a state-based peridynamic model is presented for functionally graded Kirchhoff plates. Equations of motion of the new formulation are obtained using the Euler–Lagrange equation and Taylor’s expansion. The formulation is verified by considering several benchmark problems including a clamped plate subjected to transverse loading and a simply supported plate subjected to transverse loading and inclined loading. The material properties are chosen such that Young’s modulus is assumed to be varied linearly through the thickness direction and Poisson’s ratio is constant. Peridynamic results are compared against finite element analysis results, and a very good agreement is obtained between the two approaches.

DEPP Co-Extruded Functionally Graded Piezoceramics

Aerospace ◽  
2005 ◽  
Author(s):  
Paul W. Alexander ◽  
Diann Brei ◽  
John W. Halloran
Keyword(s):  
Electric Field ◽  
Piezoelectric Actuator ◽  
Stress Reduction ◽  
Gradient Method ◽  
High Stress ◽  
Layered Material ◽  
Functionally Graded ◽  
Reliability Testing ◽  
Micro Fabrication ◽  
Complex Electric Field

Functionally Graded Piezoceramics (FGP) offer performance similar to conventional piezoceramic actuators while reducing the problems associated with their bonded construction (high stress levels, large stress discontinuities, delamination, etc.). This paper presents the Dual Electro/Piezo Property (DEPP) gradient method and the tools necessary for designing, modeling, and producing DEPP FGP actuators including: material property gradient maps, a Micro-Fabrication by Co-eXtrusion (MFCX) process, and experimentally validated analytic and numeric performance and stress modeling methodologies that account for continuous and layered material gradients and complex electric field profiles. These models predict a dramatic internal stress reduction achieved by the DEPP method. Preliminary reliability testing confirm this with an increase in piezoelectric actuator lifetimes over 1010 cycles, improvement of almost four orders of magnitude compared to conventional piezoceramic actuation.

The Higher Order Crack Tip Fields for Anti-Plane Crack in Functionally Graded Piezoelectric Materials

2014 ◽  
Vol 472 ◽  
pp. 617-620 ◽  
Author(s):  
Yao Dai ◽  
Xiao Chong ◽  
Shi Min Li
Keyword(s):  
Material Properties ◽  
Piezoelectric Materials ◽  
Crack Problem ◽  
Functionally Graded ◽  
Plane Crack ◽  
Homogeneous Material ◽  
Plane Shear ◽  
Functionally Graded Piezoelectric Materials ◽  
Fundamental Significance ◽  
Functionally Graded Piezoelectric

The anti-plane crack problem is studied in functionally graded piezoelectric materials (FGPMs). The material properties of the FGPMs are assumed to be the exponential function of y. The crack is electrically impermeable and loaded by anti-plane shear tractions and in-plane electric displacements. Similar to the Williams solution of homogeneous material, the high order asymptotic fields are obtained by the method of asymptotic expansion. This investigation possesses fundamental significance as Williams solution.

scholarly journals Sensuator: A Hybrid Sensor–Actuator Approach to Soft Robotic Proprioception Using Recurrent Neural Networks

Actuators ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 30
Author(s):  
Pornthep Preechayasomboon ◽  
Eric Rombokas
Keyword(s):  
Neural Networks ◽  
Recurrent Neural Networks ◽  
Linear Models ◽  
Open Loop ◽  
Proof Of Concept ◽  
State Estimator ◽  
Loop Control ◽  
Practical Applications ◽  
Soft Actuator ◽  
The Cost

Soft robotic actuators are now being used in practical applications; however, they are often limited to open-loop control that relies on the inherent compliance of the actuator. Achieving human-like manipulation and grasping with soft robotic actuators requires at least some form of sensing, which often comes at the cost of complex fabrication and purposefully built sensor structures. In this paper, we utilize the actuating fluid itself as a sensing medium to achieve high-fidelity proprioception in a soft actuator. As our sensors are somewhat unstructured, their readings are difficult to interpret using linear models. We therefore present a proof of concept of a method for deriving the pose of the soft actuator using recurrent neural networks. We present the experimental setup and our learned state estimator to show that our method is viable for achieving proprioception and is also robust to common sensor failures.

scholarly journals Ring-Forming Polymerization toward Perfluorocyclobutyl and Ortho-Diynylarene-Derived Materials: From Synthesis to Practical Applications

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1486
Author(s):  
Eugene B. Caldona ◽  
Ernesto I. Borrego ◽  
Ketki E. Shelar ◽  
Karl M. Mukeba ◽  
Dennis W. Smith
Keyword(s):  
Chemical Resistance ◽  
Structural Features ◽  
Review Article ◽  
Aryl Ether ◽  
Aromatic Rings ◽  
Practical Applications ◽  
Repeat Units ◽  
Wide Range ◽  
Synthetic Routes ◽  
The Cost

Many desirable characteristics of polymers arise from the method of polymerization and structural features of their repeat units, which typically are responsible for the polymer’s performance at the cost of processability. While linear alternatives are popular, polymers composed of cyclic repeat units across their backbones have generally been shown to exhibit higher optical transparency, lower water absorption, and higher glass transition temperatures. These specifically include polymers built with either substituted alicyclic structures or aromatic rings, or both. In this review article, we highlight two useful ring-forming polymer groups, perfluorocyclobutyl (PFCB) aryl ether polymers and ortho-diynylarene- (ODA) based thermosets, both demonstrating outstanding thermal stability, chemical resistance, mechanical integrity, and improved processability. Different synthetic routes (with emphasis on ring-forming polymerization) and properties for these polymers are discussed, followed by their relevant applications in a wide range of aspects.

scholarly journals Broadband metamaterials and metasurfaces: a review from the perspectives of materials and devices

Nanophotonics ◽  
2020 ◽  
Vol 9 (10) ◽  
pp. 3165-3196 ◽  
Author(s):  
Joonkyo Jung ◽  
Hyeonjin Park ◽  
Junhyung Park ◽  
Taeyong Chang ◽  
Jonghwa Shin
Keyword(s):  
Material Properties ◽  
Frequency Bandwidth ◽  
Broad Bandwidth ◽  
Practical Applications ◽  
Effective Material Properties

AbstractMetamaterials can possess extraordinary properties not readily available in nature. While most of the early metamaterials had narrow frequency bandwidth of operation, many recent works have focused on how to implement exotic properties and functions over broad bandwidth for practical applications. Here, we provide two definitions of broadband operation in terms of effective material properties and device functionality, suitable for describing materials and devices, respectively, and overview existing broadband metamaterial designs in such two categories. Broadband metamaterials with nearly constant effective material properties are discussed in the materials part, and broadband absorbers, lens, and hologram devices based on metamaterials and metasurfaces are discussed in the devices part.

scholarly journals Enhanced Thermoelectric Performance of n-Type Bi2Se3 Nanosheets through Sn Doping

Nanomaterials ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1827
Author(s):  
Mengyao Li ◽  
Yu Zhang ◽  
Ting Zhang ◽  
Yong Zuo ◽  
Ke Xiao ◽  
...  
Keyword(s):  
Figure Of Merit ◽  
Cost Effective ◽  
Low Grade ◽  
Hot Press ◽  
Processing Technologies ◽  
Sn Doping ◽  
Practical Applications ◽  
Alternative Materials ◽  
The Cost ◽  
Low Grade Heat

The cost-effective conversion of low-grade heat into electricity using thermoelectric devices requires developing alternative materials and material processing technologies able to reduce the currently high device manufacturing costs. In this direction, thermoelectric materials that do not rely on rare or toxic elements such as tellurium or lead need to be produced using high-throughput technologies not involving high temperatures and long processes. Bi2Se3 is an obvious possible Te-free alternative to Bi2Te3 for ambient temperature thermoelectric applications, but its performance is still low for practical applications, and additional efforts toward finding proper dopants are required. Here, we report a scalable method to produce Bi2Se3 nanosheets at low synthesis temperatures. We studied the influence of different dopants on the thermoelectric properties of this material. Among the elements tested, we demonstrated that Sn doping resulted in the best performance. Sn incorporation resulted in a significant improvement to the Bi2Se3 Seebeck coefficient and a reduction in the thermal conductivity in the direction of the hot-press axis, resulting in an overall 60% improvement in the thermoelectric figure of merit of Bi2Se3.

Optimal stationary strategies in leavable Markov decision processes

1990 ◽  
Vol 27 (01) ◽  
pp. 134-145
Author(s):  
Matthias Fassbender
Keyword(s):  
Transition Probabilities ◽  
Practical Applications ◽  
Stationary Strategies ◽  
Countable State ◽  
Markov Decision ◽  
Bias Optimality ◽  
The Mean ◽  
Optimal Stationary Strategies ◽  
The Cost ◽  
Reward Criterion

This paper establishes the existence of an optimal stationary strategy in a leavable Markov decision process with countable state space and undiscounted total reward criterion. Besides assumptions of boundedness and continuity, an assumption is imposed on the model which demands the continuity of the mean recurrence times on a subset of the stationary strategies, the so-called ‘good strategies'. For practical applications it is important that this assumption is implied by an assumption about the cost structure and the transition probabilities. In the last part we point out that our results in general cannot be deduced from related works on bias-optimality by Dekker and Hordijk, Wijngaard or Mann.

scholarly journals A Review of Bolt Tightening Force Measurement and Loosening Detection

Sensors ◽  
2020 ◽  
Vol 20 (11) ◽  
pp. 3165 ◽  
Author(s):  
Rusong Miao ◽  
Ruili Shen ◽  
Songhan Zhang ◽  
Songling Xue
Keyword(s):  
Force Measurement ◽  
Axial Stress ◽  
High Stress ◽  
Bolted Joints ◽  
Practical Applications ◽  
Tightening Force ◽  
Existing Structures ◽  
Strength Failure ◽  
Joint Connection ◽  
Art Research

Pre-stressed bolted joints are widely used in civil structures and industries. The tightening force of a bolt is crucial to the reliability of the joint connection. Loosening or over-tightening of a bolt may lead to connectors slipping or bolt strength failure, which are both harmful to the main structure. In most practical cases it is extremely difficult, even impossible, to install the bolts to ensure there is a precise tension force during the construction phase. Furthermore, it is inevitable that the bolts will loosen due to long-term usage under high stress. The identification of bolt tension is therefore of great significance for monitoring the health of existing structures. This paper reviews state-of-the-art research on bolt tightening force measurement and loosening detection, including fundamental theories, algorithms, experimental set-ups, and practical applications. In general, methods based on the acoustoelastic principle are capable of calculating the value of bolt axial stress if both the time of incident wave and reflected wave can be clearly recognized. The relevant commercial instrument has been developed and its algorithm will be briefly introduced. Methods based on contact dynamic phenomena such as wave energy attenuation, high-order harmonics, sidebands, and impedance, are able to correlate interface stiffness and the clamping force of bolted joints with respective dynamic indicators. Therefore, they are able to detect or quantify bolt tightness. The related technologies will be reviewed in detail. Potential challenges and research trends will also be discussed.

Thermal Post-Buckling Analysis of Functionally Graded Composite Plates with Nonlinear Aerodynamic Forces

2010 ◽  
Vol 123-125 ◽  
pp. 280-283
Author(s):  
Chang Yull Lee ◽  
Ji Hwan Kim
Keyword(s):  
Material Properties ◽  
Numerical Solutions ◽  
Virtual Work ◽  
Shear Deformation Theory ◽  
Composite Plates ◽  
Buckling Analysis ◽  
Functionally Graded ◽  
Governing Equations ◽  
Functionally Graded Composite ◽  
Post Buckling

The post-buckling of the functionally graded composite plate under thermal environment with aerodynamic loading is studied. The structural model has three layers with ceramic, FGM and metal, respectively. The outer layers of the sandwich plate are different homogeneous and isotropic material properties for ceramic and metal. Whereas the core is FGM layer, material properties vary continuously from one interface to the other in the thickness direction according to a simple power law distribution in terms of the volume fractions. Governing equations are derived by using the principle of virtual work and numerical solutions are solved through a finite element method. The first-order shear deformation theory and von-Karman strain-displacement relations are based to derive governing equations of the plate. Aerodynamic effects are dealt by adopting nonlinear third-order piston theory for structural and aerodynamic nonlinearity. The Newton-Raphson iterative method applied for solving the nonlinear equations of the thermal post-buckling analysis

Sign in / Sign up

Export Citation Format

Share Document