CFD Modeling of Gas Particle Flow Within a Solid Particle Solar Receiver

Solar Energy ◽  
2006 ◽  
Author(s):  
Huajun Chen ◽  
Yitung Chen ◽  
Hsuan-Tsung Hsieh ◽  
Nathan Siegel
Keyword(s):  
Heat Transfer ◽  
Solar Radiation ◽  
Solid Particle ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Operating Conditions ◽  
Solid Particles ◽  
Particle Flow ◽  
Cfd Modeling ◽  
Solar Receiver

A detailed three dimensional computational fluid dynamics (CFD) analysis on gas-particle flow and heat transfer inside a solid particle solar receiver, which utilizes free-falling particles for direct absorption of concentrated solar radiation, is presented. The two-way coupled Euler-Lagrange method is implemented and includes the exchange of heat and momentum between the gas phase and solid particles. A two band discrete ordinate method is included to investigate radiation heat transfer within the particle cloud and between the cloud and the internal surfaces of the receiver. The direct illumination energy source that results from incident solar radiation was predicted by a solar load model using a solar ray tracing algorithm. Two kinds of solid particle receivers, each having a different exit condition for the solid particles, are modeled to evaluate the thermal performance of the receiver. Parametric studies, where the particle size and mass flow rate are varied, are made to determine the optimal operating conditions. The results also include detailed information for the particle and gas velocity, temperature, particle solid volume fraction, and cavity efficiency.

Computational Fluid Dynamics Modeling of Gas-Particle Flow Within a Solid-Particle Solar Receiver

2006 ◽  
Vol 129 (2) ◽  
pp. 160-170 ◽  
Author(s):  
Huajun Chen ◽  
Yitung Chen ◽  
Hsuan-Tsung Hsieh ◽  
Nathan Siegel
Keyword(s):  
Heat Transfer ◽  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Solar Radiation ◽  
Solid Particle ◽  
Operating Conditions ◽  
Solid Particles ◽  
Particle Flow ◽  
Outlet Temperature ◽  
Solar Receiver

A detailed three-dimensional computational fluid dynamics (CFD) analysis on gas-particle flow and heat transfer inside a solid-particle solar receiver, which utilizes free-falling particles for direct absorption of concentrated solar radiation, is presented. The two-way coupled Euler-Lagrange method is implemented and includes the exchange of heat and momentum between the gas phase and solid particles. A two-band discrete ordinate method is included to investigate radiation heat transfer within the particle cloud and between the cloud and the internal surfaces of the receiver. The direct illumination energy source that results from incident solar radiation was predicted by a solar load model using a solar ray-tracing algorithm. Two kinds of solid-particle receivers, each having a different exit condition for the solid particles, are modeled to evaluate the thermal performance of the receiver. Parametric studies, where the particle size and mass flow rate are varied, are made to determine the optimal operating conditions. The results also include detailed information for the gas velocity, temperature, particle solid volume fraction, particle outlet temperature, and cavity efficiency.

Numerical Investigation on Optimal Design of Solid Particle Solar Receiver

2007 ◽  
Author(s):  
Huajun Chen ◽  
Yitung Chen ◽  
Hsuan-Tsung Hsieh ◽  
Greg Kolb ◽  
Nathan Siegel
Keyword(s):  
Solar Radiation ◽  
Solid Particle ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Solid Particles ◽  
Load Model ◽  
Concentrated Solar Radiation ◽  
Tracing Algorithm ◽  
Solar Receiver ◽  
And Storage

Solar thermo-chemical processes often require high temperatures that can be achieved by direct absorption of solar energy. The solid particle solar receiver can be used to heat ceramic particles that may serve as a heat transfer and storage medium or as a substrate on which chemical reaction may be performed directly. Using solid particles enclosed in a cavity to absorb concentrated solar radiation can provide efficient absorption of concentrated sunlight. In this work, different solid particle solar receiver designs have been investigated by using computation fluid dynamics (CFD) technique. The gas particle flow with the solid particle solar receiver was simulated by using two-way coupled Euler-Lagrange method. The direct illumination energy source that results from incident solar radiation was predicted by a solar load model using a solar ray tracing algorithm. The detailed information to guide the experiment, such as the particle and gas velocity, temperature, particle solid volume fraction, and cavity efficiency under different designs has been analyzed.

Performance of Solid Particle Receivers With or Without the Protection of an Aerowindow

2008 ◽  
Author(s):  
Taide Tan ◽  
Yitung Chen ◽  
Zhuoqi Chen
Keyword(s):  
Solar Radiation ◽  
Solid Particle ◽  
Convection Heat Transfer ◽  
Radiation Energy ◽  
Solid Particles ◽  
Wind Effect ◽  
Air Jet ◽  
Optimal Injection ◽  
Solar Receiver ◽  
Prototype Design

A solid particle solar receiver (SPSR) is a direct absorption central receiver that uses solid particles enclosed in a cavity to absorb concentrated solar radiation. However, the existing open aperture lowers the overall efficiency by convection heat transfer. Aerowindows have the potential of increasing the efficiency of an SPSR by reducing convective losses from an open receiver aperture and eliminate reflection, convection and reradiation losses from a comparable glass window. Aerodynamic windows consist of a transparent gas stream, which is injected from an air jet, across the receiver aperture to isolate its interior from the surrounding atmosphere. Even though, the wind conditions may still have important effect on the performance of SPSRs. In the present paper, the wind effect on the performance of an SPSR is investigated numerically. The mass, momentum and energy exchange between the solid particle and air flow are simulated by the two-way coupling Euler-Lagrange method in the realizable k-ε turbulence 3D model. The independence of the calculating domain is studied in order to select a proper domain for the numerical simulation. Solar ray tracing method is employed in calculating the solar radiation energy. The numerical investigation of the performance of the SPSR is focusing on optimizing the prototype design and finding out the best working condition for the SPSR. In order to investigate the influences of the wind speed and wind blowing direction on the performance of the receiver, different wind conditions of and different air jet injection conditions are simulated numerically. The cavity thermal efficiencies are calculated and the optimal injection conditions are analyzed for different wind conditions.

scholarly journals Comprehensive Optimization of the Dispersion of Mixing Particles in an Inert-Particle Spouted-Bed Reactor (IPSBR) System

Processes ◽  
2021 ◽  
Vol 9 (11) ◽  
pp. 1921
Author(s):  
Ameera F. Mohammad ◽  
Aya A-H. I. Mourad ◽  
Ali H. Al-Marzouqi ◽  
Muftah H. El-Naas ◽  
Bart Van der Bruggen ◽  
...  
Keyword(s):  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Particle Diameter ◽  
Operating Conditions ◽  
Solid Particles ◽  
Orifice Diameter ◽  
Inert Particle ◽  
Gas Velocity ◽  
Spouted Bed ◽  
Gas Dispersion

Effective gas dispersion and liquid mixing are significant parameters in the design of an inert-particle spouted-bed reactor (IPSBR) system. Solid particles can be used to ensure good mixing and an efficient rate of mass and heat transfer between the gas and liquid. In this study, computational fluid dynamics (CFD) coupled with the discrete phase model (DPM) were developed to investigate the effect of the feed gas velocity (0.5–1.5 m/s), orifice diameter (0.001–0.005 m), gas head (0.15–0.35 m), particle diameter (0.009–0.0225 m), and mixing-particle-to-reactor-volume fraction (2.0–10.0 vol.%) on the solid mass concentration, average solid velocity, and average solid volume fraction in the upper, middle, and conical regions of the reactor. Statistical analysis was performed using a second-order response surface methodology (RSM) with central composite design (CCD) to obtain the optimal operating conditions. Selected parameters were optimized to maximize the responses in the middle and upper regions, and minimize them in the conical region. Such conditions produced a high interfacial area and fewer dead zones owing to good particle dispersion. The optimal process variables were feed gas velocity of 1.5 m/s, orifice diameter of 0.001 m, gas head of 0.2025 m, a particle diameter of 0.01 m, and a particle load of 0.02 kg. The minimum average air velocity and maximum air volume fraction were observed under the same operating conditions. This confirmed the novelty of the reactor, which could work at a high feed gas velocity while maintaining a high residence time and gas volume fraction.

Effects of uniform or non-uniform heating at bottom wall on MHD mixed convection in a porous cavity saturated by nanofluid

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Subramanian Muthukumar ◽  
Selvaraj Sureshkumar ◽  
Arthanari Malleswaran ◽  
Murugan Muthtamilselvan ◽  
Eswari Prem
Keyword(s):  
Magnetic Field ◽  
Heat Transfer ◽  
Transfer Rate ◽  
Hartmann Number ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Darcy Number ◽  
Bottom Wall ◽  
Uniform Heating ◽  
The Magnetic Field

Abstract A numerical investigation on the effects of uniform and non-uniform heating of bottom wall on mixed convective heat transfer in a square porous chamber filled with nanofluid in the appearance of magnetic field is carried out. Uniform or sinusoidal heat source is fixed at the bottom wall. The top wall moves in either positive or negative direction with a constant cold temperature. The vertical sidewalls are thermally insulated. The finite volume approach based on SIMPLE algorithm is followed for solving the governing equations. The different parameters connected with this study are Richardson number (0.01 ≤ Ri ≤ 100), Darcy number (10−4 ≤ Da ≤ 10−1), Hartmann number (0 ≤ Ha ≤ 70), and the solid volume fraction (0.00 ≤ χ ≤ 0.06). The results are presented graphically in the form of isotherms, streamlines, mid-plane velocities, and Nusselt numbers for the various combinations of the considered parameters. It is observed that the overall heat transfer rate is low at Ri = 100 in the positive direction of lid movement, whereas it is low at Ri = 1 in the negative direction. The average Nusselt number is lowered on growing Hartmann number for all considered moving directions of top wall with non-uniform heating. The low permeability, Da = 10−4 keeps the flow pattern same dominating the magnetic field, whereas magnetic field strongly affects the flow pattern dominating the high Darcy number Da = 10−1. The heat transfer rate increases on enhancing the solid volume fraction regardless of the magnetic field.

scholarly journals A sensitivity study on carbon nanotubes significance in Darcy–Forchheimer flow towards a rotating disk by response surface methodology

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Anum Shafiq ◽  
Tabassum Naz Sindhu ◽  
Qasem M. Al-Mdallal
Keyword(s):  
Heat Transfer ◽  
Carbon Nanotubes ◽  
Ethylene Glycol ◽  
Biot Number ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Rotating Disk ◽  
Sensitivity Study ◽  
Basic Fluid ◽  
Walled Cnts

AbstractThe current research explores incremental effect of thermal radiation on heat transfer improvement corresponds to Darcy–Forchheimer (DF) flow of carbon nanotubes along a stretched rotating surface using RSM. Casson carbon nanotubes’ constructed model in boundary layer flow is being investigated with implications of both single-walled CNTs and multi-walled CNTs. Water and Ethylene glycol are considered a basic fluid. The heat transfer rate is scrutinized via convective condition. Outcomes are observed and evaluated for both SWCNTs and MWCNTs. The Runge–Kutta Fehlberg technique of shooting is utilized to numerically solve transformed nonlinear ordinary differential system. The output parameters of interest are presumed to depend on governing input variables. In addition, sensitivity study is incorporated. It is noted that sensitivity of SFC via SWCNT-Water becomes higher by increasing values of permeability number. Additionaly, sensitivity of SFC via SWCNT-water towards the permeability number is higher than the solid volume fraction for medium and higher permeability levels. It is also noted that sensitivity of SFC (SWCNT-Ethylene-glycol) towards volume fraction is higher for increasing permeability as well as inertia coefficient. Additionally, the sensitivity of LNN towards the Solid volume fraction is higher than the radiation and Biot number for all levels of Biot number. The findings will provide initial direction for future device manufacturing.

Pool Boiling Characteristics of Metallic Nanofluids

2011 ◽  
Vol 133 (11) ◽  
Author(s):  
K. Hari Krishna ◽  
Harish Ganapathy ◽  
G. Sateesh ◽  
Sarit K. Das
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Boiling Heat Transfer ◽  
Volume Fraction ◽  
Pool Boiling ◽  
Heat Fluxes ◽  
Solid Particles ◽  
Heater Surface ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Nanofluids, solid-liquid suspensions with solid particles of size of the order of few nanometers, have created interest in many researchers because of their enhancement in thermal conductivity and convective heat transfer characteristics. Many studies have been done on the pool boiling characteristics of nanofluids, most of which have been with nanofluids containing oxide nanoparticles owing to the ease in their preparation. Deterioration in boiling heat transfer was observed in some studies. Metallic nanofluids having metal nanoparticles, which are known for their good heat transfer characteristics in bulk regime, reported drastic enhancement in thermal conductivity. The present paper investigates into the pool boiling characteristics of metallic nanofluids, in particular of Cu-H2O nanofluids, on flat copper heater surface. The results indicate that at comparatively low heat fluxes, there is deterioration in boiling heat transfer with very low particle volume fraction of 0.01%, and it increases with volume fraction and shows enhancement with 0.1%. However, the behavior is the other way around at high heat fluxes. The enhancement at low heat fluxes is due to the fact that the effect of formation of thin sorption layer of nanoparticles on heater surface, which causes deterioration by trapping the nucleation sites, is overshadowed by the increase in microlayer evaporation, which is due to enhancement in thermal conductivity. Same trend has been observed with variation in the surface roughness of the heater as well.

scholarly journals Numerical Analysis of Nanofluids in Differentially Heated Enclosure Undergoing Orthogonal Rotation

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
H. Saleh ◽  
I. Hashim
Keyword(s):  
Heat Transfer ◽  
Transfer Rate ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Convection Heat Transfer ◽  
Staggered Grid ◽  
Governing Equations ◽  
Nanoparticles Concentration ◽  
Quantity Of Heat ◽  
Velocity Pressure

Natural convection heat transfer in a rotating, differentially heated enclosure is studied numerically in this paper. The rotating enclosure is filled with water-Ag, water-Cu, water-Al2O3, or water-TiO2nanofluids. The governing equations are in velocity, pressure, and temperature formulation and solved using the staggered grid arrangement together with MAC method. The governing parameters considered are the solid volume fraction,0.0 ≤ ϕ ≤ 0.05, and the rotational speeds,3.5≤ Ω ≤ 17.5 rpm, and the centrifugal force is smaller than the Coriolis force and both forces were kept below the buoyancy force. It is found that the angular locations of the local maximums heat transfer were sensitive to rotational speeds and nanoparticles concentration. The global quantity of heat transfer rate increases about 1.5%, 1.1%, 0.8%, and 0.6% by increasing 1%ϕof the nanoparticles Ag, Cu, Al2O3, and TiO2, respectively, for the considered rotational speeds.

Turbulent Nanofluid Flow Analysis Passing a Shell and Tube Thermal Exchanger with Kays-Crawford Model

2021 ◽  
Vol 10 (4) ◽  
pp. 518-537
Author(s):  
R. Nasrin ◽  
S. A. Sweety ◽  
I. Zahan
Keyword(s):  
Heat Transfer ◽  
Volume Fraction ◽  
Pure Water ◽  
Fluid Velocity ◽  
Solid Volume Fraction ◽  
Heat Transfer Analysis ◽  
Inlet Temperature ◽  
Industrial Sectors ◽  
Shell And Tube ◽  
Thermal Exchanger

Temperature dissipation in a proficient mode has turned into a crucial challenge in industrial sectors because of worldwide energy crisis. In heat transfer analysis, shell and tube thermal exchangers is one of the mostly used strategies to control competent heat transfer in industrial progression applications. In this research, a numerical analysis of turbulent flow has been conceded in a shell and tube thermal exchanger using Kays-Crawford model to investigate the thermal performance of pure water and different concentrated water-MWCNT nanofluid. By means of finite element method the Reynold-Averaged Navier-Stokes (RANS) and heat transport equations along with suitable edge conditions have been worked out numerically. The implications of velocity, solid concentration, and temperature of water-MWCNT nanofluid on the fluid flow formation and heat transfer scheme have been inspected thoroughly. The numerical results indicate that the variation of nanoparticles solid volume fraction, inflow fluid velocity and inlet temperature mannerism considerably revolutionize in the flow and thermal completions. It is perceived that using 3% concentrated water-MWCNT nanofluid, higher rate of heat transfer 12.24% is achieved compared that of water and therefore to enhance the efficiency of this heat exchanger. Furthermore, a new correlation has been developed among obtained values of thermal diffusion rate, Reynolds number and volume concentration of nanoparticle and found very good correlation coefficient among the values.

Influence of Cu-Water and CNT-Water Nanofluid on Natural Convection Heat Transfer in a Triangular Solar Collector

2020 ◽  
Author(s):  
Didarul Ahasan Redwan ◽  
Md. Habibur Rahman ◽  
Hasib Ahmed Prince ◽  
Emdadul Haque Chowdhury ◽  
M. Ruhul Amin
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Rayleigh Number ◽  
Solar Collector ◽  
Average Nusselt Number ◽  
Volume Fraction ◽  
Solid Volume Fraction ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Convection Heat

Abstract A numerical study on natural convection heat transfer in a right triangular solar collector filled with CNT-water and Cuwater nanofluids has been conducted. The inclined wall and the bottom wall of the cavity are maintained at a relatively lower temperature (Tc), and higher temperature (Th), respectively, whereas the vertical wall, is kept adiabatic. The governing non-dimensional partial differential equations are solved by using the Galerkin weighted residual finite element method. The Rayleigh number (Ra) and the solid volume-fraction of nanoparticles (ϕ) are varied in the range of 103 ≤ Ra ≤ 106, and 0 ≤ ϕ ≤ 0.1, respectively, to carry out the parametric simulations within the laminar region. Corresponding thermal and flow fields are presented via isotherms and streamlines. Variations of average Nusselt number as a function of Rayleigh number have been examined for different solid volume-fraction of nanoparticles. It has been found that the natural convection heat transfer becomes stronger with the increment of solid volume fraction and Rayleigh number, but the strength of circulation reduces with increasing nanoparticles’ concentration at low Ra. Conduction mode dominates for lower Ra up to a certain limit of 104. It is also observed that when the solid volume fraction is increased from 0 to 0.1 for a particular Rayleigh number, the average Nusselt number is increased to a great extent, but surprisingly, the rate of increment is more pronounced at lower Ra. Moreover, it is seen that Cu-water nanofluid offers slightly better performance compared to CNT-water but the difference is very little, especially at lower Ra.

Sign in / Sign up

Export Citation Format

Share Document