Study on Incorporation of New Design Fatigue Curves and a New Environmental Fatigue Correction Factor for PWR Environment Into the JSME Environmental Fatigue Evaluation Method

2020 ◽  
Author(s):  
Seiji Asada ◽  
Shengde Zhang ◽  
Masahiro Takanashi ◽  
Yuichiro Nomura
Keyword(s):  
Stainless Steel ◽  
Base Metal ◽  
Stainless Steels ◽  
Evaluation Method ◽  
Austenitic Stainless Steels ◽  
Steel Base ◽  
Improved Design ◽  
Fatigue Evaluation ◽  
Cast Stainless Steel ◽  
Metal Weld

Abstract Improved design fatigue curves were developed in the Subcommittee on Design Fatigue Curve in the Atomic Energy Research Committee in the Japan Welding Engineering Society (JWES). Working Group on Design Fatigue Curves (WG DFC) in the JSME has studied the validity and the applicability of the improved design fatigue curves developed in the JWES to incorporate into the JSME Environmental Fatigue Evaluation Method. The authors propose a fatigue analysis method using the design fatigue curves developed in the JWES that are applied revised factors to optimize the environmental fatigue analysis. Also, the Japanese pressurized water reactor (PWR) utility group developed equations of environmental fatigue factors (Fen) for austenitic stainless steel base metal, weld metal and cast stainless steel in PWR environment. The WG DFC has investigated the Fen equations and concluded that the Fen equation of austenitic stainless steel base metal is the most conservative among the three equations and close to NUREG/CR-6909 Rev.1 [24]. The authors propose to use the Fen equation for base metal for austenitic stainless steels for all of the base metal, weld metal and cast stainless steel. In addition, the authors have confirmed that the employment of the proposed Fen equation to the proposed design fatigue curves of austenitic stainless steels accurately predicts the existing environmental fatigue test data of austenitic stainless steels, which were used in the development of the current Fen equation of austenitic stainless steels in PWR environments in the JSME Environmental Fatigue Evaluation Method. Therefore, the proposed Fen equation can be applied to environmental fatigue evaluation for austenitic stainless steels.

Development of New Design Fatigue Curves in Japan: Proposal of a New Fatigue Evaluation Method

2018 ◽  
Author(s):  
Seiji Asada ◽  
Akihiko Hirano ◽  
Toshiyuki Saito ◽  
Yasukazu Takada ◽  
Hideo Kobayashi
Keyword(s):  
Stainless Steels ◽  
Evaluation Method ◽  
Austenitic Stainless Steels ◽  
Fatigue Tests ◽  
Carbon Steels ◽  
Low Alloy Steels ◽  
Stress Effect ◽  
Fatigue Data ◽  
Alloy Steels ◽  
Fatigue Evaluation

In order to develop new design fatigue curves for carbon steels & low-alloy steels and austenitic stainless steels and a new design fatigue evaluation method that are rational and have clear design basis, Design Fatigue Curve (DFC) Phase 1 subcommittee and Phase 2 subcommittee were established in the Atomic Energy Research Committee in the Japan Welding Engineering Society (JWES). The study on design fatigue curves was actively performed in the subcommittees. In the subcommittees, domestic and foreign fatigue data of small test specimens in air were collected and a comprehensive fatigue database (≈6000 data) was constructed and the accurate best-fit curves of carbon steels & low-alloy steels and austenitic stainless steels were developed. Design factors were investigated. Also, a Japanese utility collaborative project performed large scale fatigue tests using austenitic stainless steel piping and low-alloy steel flat plates as well as fatigue tests using small specimens to obtain not only basic data but also fatigue data of mean stress effect, surface finish effect and size effect. Those test results were provided to the subcommittee and utilized the above studies. Based on the above studies, a new fatigue evaluation method has been developed.

ALZ 316

Alloy Digest ◽  
1999 ◽  
Vol 48 (8) ◽  
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
Austenitic Stainless Steel ◽  
Physical Properties ◽  
Tensile Properties ◽  
Stainless Steels ◽  
Austenitic Stainless Steels ◽  
Heat Treating

Abstract ALZ 316 is an austenitic stainless steel with good formability, corrosion resistance, toughness, and mechanical properties. It is the basic grade of the stainless steels, containing 2 to 3% molybdenum. After the 304 series, the molybdenum-containing stainless steels are the most widely used austenitic stainless steels. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-756. Producer or source: ALZ nv.

ALLOY 0Cr25Ni6Mo3CuN

Alloy Digest ◽  
1998 ◽  
Vol 47 (2) ◽  
Keyword(s):  
Fracture Toughness ◽  
Stainless Steel ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Physical Properties ◽  
Stainless Steels ◽  
Austenitic Stainless Steels ◽  
Temperature Performance ◽  
Steel Research ◽  
Oil Refinement

Abstract ALLOY 0Cr25Ni6Mo3CuN is one of four grades of duplex stainless steel that were developed and have found wide applications in China since 1980. In oil refinement and the petrochemical processing industries, they have substituted for austenitic stainless steels in many types of equipment, valves, and pump parts. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on low and high temperature performance, and corrosion resistance as well as forming and joining. Filing Code: SS-706. Producer or source: Central Iron & Steel Research Institute.

CARTECH 347

Alloy Digest ◽  
2021 ◽  
Vol 70 (9) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Austenitic Stainless Steel ◽  
Stainless Steels ◽  
Intergranular Corrosion ◽  
Austenitic Stainless Steels ◽  
Heat Treating ◽  
Intermittent Heating ◽  
Technology Corporation ◽  
Carpenter Technology Corporation

Abstract CarTech 347 is a niobium+tantalum stabilized austenitic stainless steel. Like Type 321 austenitic stainless steel, it has superior intergranular corrosion resistance as compared to typical 18-8 austenitic stainless steels. Since niobium and tantalum have stronger affinity for carbon than chromium, carbides of those elements tend to precipitate randomly within the grains instead of forming continuous patterns at the grain boundaries. CarTech 347 should be considered for applications requiring intermittent heating between 425 and 900 °C (800 and 1650 °F). This datasheet provides information on composition, physical properties, hardness, and tensile properties. It also includes information on corrosion resistance as well as forming, heat treating, machining, and joining. Filing Code: SS-1339. Producer or source: Carpenter Technology Corporation.

scholarly journals Surface Modification of a Nickel-Free Austenitic Stainless Steel by Low-Temperature Nitriding

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1845
Author(s):  
Francesca Borgioli ◽  
Emanuele Galvanetto ◽  
Tiberio Bacci
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Austenitic Stainless Steel ◽  
Low Temperature ◽  
Stainless Steels ◽  
Volume Fraction ◽  
Surface Hardness ◽  
Austenitic Stainless Steels ◽  
Surface Layers ◽  
Modified Surface

Low-temperature nitriding allows to improve surface hardening of austenitic stainless steels, maintaining or even increasing their corrosion resistance. The treatment conditions to be used in order to avoid the precipitation of large amounts of nitrides are strictly related to alloy composition. When nickel is substituted by manganese as an austenite forming element, the production of nitride-free modified surface layers becomes a challenge, since manganese is a nitride forming element while nickel is not. In this study, the effects of nitriding conditions on the characteristics of the modified surface layers obtained on an austenitic stainless steel having a high manganese content and a negligible nickel one, a so-called nickel-free austenitic stainless steel, were investigated. Microstructure, phase composition, surface microhardness, and corrosion behavior in 5% NaCl were evaluated. The obtained results suggest that the precipitation of a large volume fraction of nitrides can be avoided using treatment temperatures lower than those usually employed for nickel-containing austenitic stainless steels. Nitriding at 360 and 380 °C for duration up to 5 h allows to produce modified surface layers, consisting mainly of the so-called expanded austenite or gN, which increase surface hardness in comparison with the untreated steel. Using selected conditions, corrosion resistance can also be significantly improved.

Developing New Cast Austenitic Stainless Steels With Improved High-Temperature Creep Resistance

2009 ◽  
Vol 131 (5) ◽  
Author(s):  
Philip J. Maziasz ◽  
John P. Shingledecker ◽  
Neal D. Evans ◽  
Michael J. Pollard
Keyword(s):  
Stainless Steel ◽  
High Temperature ◽  
Creep Strength ◽  
Stainless Steels ◽  
Creep Resistance ◽  
Austenitic Stainless Steels ◽  
Creep Rupture ◽  
Particulate Filter ◽  
Alloy Development ◽  
Wide Range

Oak Ridge National Laboratory and Caterpillar (CAT) have recently developed a new cast austenitic stainless steel, CF8C-Plus, for a wide range of high-temperature applications, including diesel exhaust components and turbine casings. The creep-rupture life of the new CF8C-Plus is over ten times greater than that of the standard cast CF8C stainless steel, and the creep-rupture strength is about 50–70% greater. Another variant, CF8C-Plus Cu/W, has been developed with even more creep strength at 750–850°C. The creep strength of these new cast austenitic stainless steels is close to that of wrought Ni-based superalloys such as 617. CF8C-Plus steel was developed in about 1.5 years using an “engineered microstructure” alloy development approach, which produces creep resistance based on the formation of stable nanocarbides (NbC), and resistance to the formation of deleterious intermetallics (sigma, Laves) during aging or service. The first commercial trial heats (227.5 kg or 500 lb) of CF8C-Plus steel were produced in 2002, and to date, over 27,215 kg (300 tons) have been produced, including various commercial component trials, but mainly for the commercial production of the Caterpillar regeneration system (CRS). The CRS application is a burner housing for the on-highway heavy-duty diesel engines that begins the process to burn-off particulates trapped in the ceramic diesel particulate filter (DPF). The CRS/DPF technology was required to meet the new more stringent emissions regulations in January, 2007, and subjects the CRS to frequent and severe thermal cycling. To date, all CF8C-Plus steel CRS units have performed successfully. The status of testing for other commercial applications of CF8C-Plus steel is also summarized.

Corrosion Resistance of Nickel-Free Austenitic Stainless Steels and their Nanocomposites with Hydroxyapatite in Ringer's Solution

2011 ◽  
Vol 674 ◽  
pp. 159-163 ◽  
Author(s):  
Maciej Tulinski ◽  
Mieczyslaw Jurczyk
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Mechanical Alloying ◽  
Stainless Steels ◽  
Austenitic Stainless Steels ◽  
Orthopedic Implants ◽  
Corrosion Current ◽  
Similar Process ◽  
Distinct Advantage ◽  
Ion Release

In this work Ni-free austenitic stainless steels with nanostructure and their nanocomposites were synthesized by mechanical alloying (MA), heat treatment and nitriding of elemental microcrystalline Fe, Cr, Mn and Mo powders with addition of hydroxyapatite (HA). Microhardness and corrosion tests' results of obtained materials are presented. Mechanical alloying and nitriding are very effective technologies to improve the corrosion resistance of stainless steel. Decreasing the corrosion current density is a distinct advantage for prevention of ion release and it leads to better cytocompatibility. Similar process in case of nanocomposites of stainless steel with hydroxyapatite helps achieve even better mechanical properties and corrosion resistance. Hence nanocrystalline nickel-free stainless steels and nickel-free stainless steel/hydroxyapatite nanocomposites could be promising bionanomaterials for use as a hard tissue replacement implants, e.g. orthopedic implants.

Producing HP Pump Barrels Utilizing Powder Metallurgy and Hot Isostatic Pressing

2009 ◽  
Author(s):  
Martin Bjurstro¨m ◽  
Carl-Gustaf Hjorth
Keyword(s):  
High Pressure ◽  
Stainless Steel ◽  
Stainless Steels ◽  
Hot Isostatic Pressing ◽  
Austenitic Stainless Steels ◽  
Pressure Vessels ◽  
Uniform Structure ◽  
Isostatic Pressing ◽  
Near Net Shape ◽  
Hip Process

The fabrication of near net shape powder metal (PM) components by hot isostatic pressing (HIP) has been an important manufacturing technology for steel and stainless steel alloys since about 1985. The manufacturing process involves inert gas atomization of powder, 3D CAD capsule design, sheet metal capsule fabrication and densification by HIP in very large pressure vessels. Since 1985, several thousand tonnes of parts have been produced. The major applications are found in the oil and gas industry especially in offshore applications, the industrial power generation industry, and traditional engineering industries. Typically, the components replace castings, forgings and fabricated parts and are produced in high alloy grades such as martensitic steels, austenitic stainless steels, duplex (ferritic/austenitic) stainless steels and nickel based superalloys. The application of PM/HIP near net shapes to pump barrels for medium to high pressure use has a number of advantages compared to the traditional forging and welding approach. First, the need for machining of the components is reduced to a minimum and welding during final assembly is reduced substantially. Mechanical properties of the PM/HIP parts are isotropic and equal to the best forged properties in the flow direction. This derives from the fine microstructure using powder powder and the uniform structure from the HIP process. Furthermore, when using the PM HIP process the parts are produced near net shape with supports, nozzles and flanges integrated. This significantly reduces manufacturing lead-time and gives greater design flexibility which improves cost for the final component. The PM HIP near net shape route has received approval from ASTM, NACE and API for specific steel, stainless steel and nickel base alloys. This paper reviews the manufacturing sequence for PM near net shapes and discusses the details of several successful applications. The application of the PM/HIP process to high pressure pump barrels is highlighted.

Study on the Effects of Heat Treatments on the Physical and Mechanical Characteristics of 1.4301 Stainless Steel

2021 ◽  
Vol 42 ◽  
pp. 57-62
Author(s):  
Maria Stoicănescu
Keyword(s):  
Heat Treatment ◽  
Stainless Steel ◽  
Stainless Steels ◽  
Mechanical Characteristics ◽  
Austenitic Stainless Steels ◽  
Heat Treatments ◽  
Hot Plastic Deformation ◽  
Improved Characteristics ◽  
Physical And Mechanical Characteristics

The 1.4301 stainless steel is part of the category of austenitic stainless steels, steels which do no undergo heat treatments in general, as they are intended for hot plastic deformation in particular. The aim of the research presented in this paper was to obtain significantly improved characteristics of the resistance properties in relation to the values obtained under classical conditions, by applying heat treatments. Samples taken from the delivery state material underwent annealing, quenching and ageing heat treatments. Subsequently, the samples thus treated were subjected to tests enabling the determination of the correlations between the heat treatment parameters, the structure and the properties.

Sign in / Sign up

Export Citation Format

Share Document