Structural and Optical Characterization of Synthesized TiO2 Nanopowder Using Sol–Gel Technique

2016 ◽  
Vol 15 (01n02) ◽  
pp. 1650002 ◽  
Author(s):  
S. Lourduraj ◽  
R. Victor Williams
Keyword(s):  
Anatase Phase ◽  
Sol Gel ◽  
Visible Spectrum ◽  
Average Crystallite Size ◽  
Xrd Analysis ◽  
Force Microscopy ◽  
Morphological Studies ◽  
Atomic Force ◽  
Gel Technique

The nanocrystalline TiO2 powder was synthesized by sol–gel method. The XRD analysis reveals that TiO2 powder was highly crystalline (anatase phase) and nanostructured with tetragonal system. The average crystallite size after calcined at 673[Formula: see text]K is found to be 7.7[Formula: see text]nm. The surface morphological studies using scanning electron microscopy (SEM) exhibit that the formation of nanosized TiO2 particles with less densification nature. Atomic force microscopy (AFM) topography exhibits the uniform distribution of spherical-shaped particles. The energy dispersive X-ray spectroscopy (EDX) confirms the presence of Titanium and Oxygen in synthesized TiO2 nanopowder. The value of optical bandgap of TiO2 nanopowder calculated from UV-Visible spectrum is 3.45[Formula: see text]eV. The presence of TiO2 particles is confirmed from the dominant fourier transform infrared (FTIR) peaks at 621[Formula: see text]cm[Formula: see text] and 412[Formula: see text]cm[Formula: see text].

Infrared Characterization of PMMA-SiO2 Hybrid Glasses Obtained by Sol-Gel Process

2010 ◽  
Vol 1278 ◽  
Author(s):  
L.L. Díaz-Flores ◽  
A. S. López Rodríguez ◽  
P. SifuentesGallardo ◽  
M.A. Hernàndez Rivera ◽  
M.a Garnica Romo ◽  
...  
Keyword(s):  
Sol Gel ◽  
Chemical Properties ◽  
Hybrid Coatings ◽  
Force Microscopy ◽  
Air Atmosphere ◽  
Atomic Force ◽  
Sol Gel Process ◽  
Traditional Process ◽  
And Chemical Properties

AbstractThis work is about the production of hybrid coatings of the system SiO2-PMMA (PMMA, polymethylmethacrylate). These materials have interesting mechanical and chemical properties useful for anticorrosive and wear resistance applications. SiO2-PMMA hybrids were obtained by the sol-gel traditional process, using tetraethylorthosilicate (TEOS) and methylmethacrylate (MMA) by Aldrich Co, as starting reagents. The SiO2:PMMA ratio was varied from 0:1 to about 1:1 at air atmosphere deposition. The coatings were obtained on acrylic sheets and silicon wafers. A diversity of coatings with chemical composition ranging from SiO2 and PMMA to obtain the SiO2-PMMA hybrids were obtained. Infrared (IR) and atomic force microscopy (AFM), were performed to determinate structural and morphological behavior.

Effects of Annealing on Pulsed Laser Deposited TiO2 Thin Films

2013 ◽  
Vol 446-447 ◽  
pp. 306-311 ◽  
Author(s):  
Sudhanshu Dwivedi ◽  
Somnath Biswas
Keyword(s):  
Thin Films ◽  
Pulsed Laser ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Si Substrates ◽  
Morphological Studies ◽  
Atomic Force ◽  
Deposited Films ◽  
Type Crystal

Mixed phase TiO2 thin films of rutile and anatase type crystal orientations were deposited on Si substrates by pulsed laser deposition (PLD) technique. When annealed at 800°C at 1 mbar oxygen pressure for 3 h, the deposited films transform into a single phase of rutile type. Structural and morphological studies of the as-deposited and annealed films were performed with X-ray diffraction (XRD), Fourier transform infra-red spectroscopy (FTIR), Raman spectroscopy, and atomic force microscopy (AFM). Photoluminescence (PL) spectroscopy was used for optical characterization of the annealed thin films.

Surface Morphology of Seeded Nanostructured ZnO on Silicon by Sol-Gel Technique

2013 ◽  
Vol 667 ◽  
pp. 265-271 ◽  
Author(s):  
Kevin Alvin Eswar ◽  
Azlinda Ab Aziz ◽  
Mohamad Rusop Mahmood ◽  
Saifollah Abdullah
Keyword(s):  
Surface Morphology ◽  
Room Temperature ◽  
Sol Gel ◽  
Electron Microscopic ◽  
Force Microscopy ◽  
Atomic Force ◽  
Afm Analysis ◽  
Scanning Electron Microscopic ◽  
Gel Technique ◽  
P Type

Nanostructured ZnO as a seeded was prepared by sol-gel technique on p-type silicon in various low molarities. Zinc acetate, Diethanolamine (DEA), and isopropyl were use as starting material, stabilizer, and solvent respectively. Atomic Force Microscopy (AFM) analysis shows smooth surface and uniform layer were produced in low molarities of precursor. The surface morphology of nanostructured ZnO was analyzed by Field Emission Scanning Electron Microscopic (FESEM). It is found that the nanostructured ZnO were successfully deposited on the silicon substrate with size ~10 nm to ~35 nm. Photoluminescence spectroscopy was employed to study the band gap in room temperature. It shows that very low intensity of PL in 0.05m and 0.1 m. PL intensity become more obvious starting from 0.15 m of precursor concentration.

Performance Effect of ZnAl2O4 - SiO2 Thin Film for Wireless Patch Antenna Application

2014 ◽  
Vol 28 ◽  
pp. 141-150 ◽  
Author(s):  
Mohd Syafiq Zulfakar ◽  
Huda Abdullah ◽  
Mohammad Tariqul Islam ◽  
Wan Nasarudin Wan Jalal ◽  
Zalita Zainuddin ◽  
...  
Keyword(s):  
Crystallite Size ◽  
Patch Antenna ◽  
Sol Gel ◽  
Average Crystallite Size ◽  
Cubic Phase ◽  
Frequency Range ◽  
Performance Effect ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force

Polycrystalline of (1-x)ZnAl2O4 – xSiO2 compound with compositions of x = 0.00, 0.05, 0.10, 0.15, 0.20 and 0.25 have been prepared using sol-gel method. Structural properties was investigated by atomic force microscopy (AFM) and x-ray diffractometer (XRD). The AFM images analysis showed that the surface roughness of the highest composition had rougher surface compared with other samples. XRD measurement indicated that the crystallite size also increased with average crystallite size around 18 nm with cubic phase had been found. The dielectric permittivity value were measured with frequency range of 1 Hz to 1 MHz. It is showed that the dielectric value decreased as the freqeuncy was applied to the samples. The performance of the patch antenna showed that the antenna resonated at 3.30 GHz and give-13.87 dB with frequency range about 2 – 4 GHz.

scholarly journals Synthesis and Characterization of TNTs/Polyaniline Composite as Photocatalyst Degradation of Rhodamin B by Visible Light

2017 ◽  
Vol 3 (5) ◽  
pp. 41
Author(s):  
Atik Setyani ◽  
Sri Wahyuni ◽  
Sigit Priatmoko ◽  
Emas Agus Prastyo Wibowo ◽  
Nur Amin
Keyword(s):  
Energy Gap ◽  
In Situ Polymerization ◽  
Anatase Phase ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Molar Ratio ◽  
Pani Composite ◽  
Stretching Vibration

<p>The purpose of this research is to study the effect of the amount of aniline on their photocatalytic activity. Nano TiO<sub>2</sub> was synthesized using sol-gel method with TiPP precursor. XRD characterization results showed that nano TiO<sub>2</sub> with calcination temperature of 450 °C had size of 13.8 nm with high crystalline. The diffraction peaks of nano TiO<sub>2</sub> at 2θ are 24.45°; 37.075°; 47.26° and 53.18°. Nano TiO<sub>2</sub> was then synthesized with hydrothermal treatment 24 h of 140 °C to produce TNTs. The results of XRD analysis shows anatase phase with field (004) and (200). The morphology of TNTs begins to form at the calcinations temperature of 600 °C with textural coefficient value of 0.998 3 . Synthesis of composite TNTs/PANI (polyaniline) was done by in situ polymerization technique of aniline which was already contained nano TiO<sub>2</sub>. The molar ratio of aniline and APS in the synthesis of a composite is 1:1.5 with the addition of aniline of 15 %; 20 % and 25 % (w/w %). Characterization using FTIR showed the stretching vibration of the C=N in wavelength of 1 600 cm<sup>–1</sup> to mark the formation of quinonoid compounds of polyaniline. The test of the rhodamine B degradation gave the best results on the 25 % TNTs/PANI composite, with the degradation percentage of 58.73 %. The characterization results using dr-uv proved that the decrease of energy gap in the TNTs/PANI composite which as evidenced with Kubelka-Munk calculation equation that was 25 % TNTs/PANI amounting to 3.19 eV and TNTs at 3.24 eV.</p>

Effect of Copper Concentration on Characterization of Cu2Zn0.8Cd0.2SnS4 Pentrary Alloy Nanostructures

2015 ◽  
Vol 754-755 ◽  
pp. 1115-1119 ◽  
Author(s):  
A.S. Ibraheam ◽  
Y. Al-Douri ◽  
Uda Hashim
Keyword(s):  
Spin Coating ◽  
Copper Concentration ◽  
Sol Gel ◽  
Force Microscopy ◽  
Glass Substrates ◽  
Atomic Force ◽  
Average Grain Size ◽  
Alloy Nanostructures ◽  
Effect Of Copper

Cu2Zn0.8Cd0.2SnS4 pentrary alloy nanostructure were prepared and deposited on glass substrates with different copper concentrations ( 0.3, 0.5, 0.7 and 0.9 mol/L ) using Sol gel – spin coating method.morphological and analytical studies were investigated by Field Emission-Scanning Electron Microscope (FE-SEM), atomic force microscopy (AFM). It is found that the average grain size of Cu2Zn0.8Cd0.2SnS4 pentrary alloy nanostructure is 51.92 to 76.43 nm for the thin films prepared at 0.3, 0.5, 0.7 and 0.9 mol/L respectively .

Characterization of Cu2Zn1-xCdxSnS4 Nanostructures

2015 ◽  
Vol 1109 ◽  
pp. 171-175 ◽  
Author(s):  
A.S. Ibraheam ◽  
Y. Al-Douri ◽  
U. Hashim ◽  
M. Wesam Al-Mufti
Keyword(s):  
Grain Size ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sol Gel ◽  
Obvious Effect ◽  
Atomic Force ◽  
Characterization Study ◽  
Gel Technique ◽  
Scanning Electron

Pentrary alloys of Cu2Zn1-xCdxSnS4 nanostructures have been grown on glass substrate using sol-gel technique. The concentration of Cd has showed obvious effect for characterization study. Field emission-scanning electron microscope (FE-SEM) and atomic force microscope (AFM) have provide nanostructures of the utilized alloys. Those alloys give good impression about increasing the grain size with Cd concentration increasing, that lead to increasing the surface coarse.

Structural, Magnetic and Microwave Absorbing Properties of Nanosized NiXZn1-xFe2O4 Powders Synthesized by Sol-Gel Technique

2010 ◽  
Vol 148-149 ◽  
pp. 1144-1147
Author(s):  
Xiang Rong Zhu ◽  
Lin Feng Lu ◽  
Hong Lie Shen
Keyword(s):  
Room Temperature ◽  
Structural Characteristics ◽  
Sol Gel ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
X Ray ◽  
Force Microscopy ◽  
Atomic Force ◽  
Gel Technique ◽  
Soft Magnetism

NixZn1-xFe2O4 (x=0.4, 0.6) powders are synthesized by sol-gel technique. The X-ray diffraction (XRD) measurements show their polycrystalline spinel structural characteristics. Both XRD and Atomic Force Microscopy demonstrate the samples are nanosized. At room temperature typical soft magnetism is exhibited by the samples. The reflection attenuation resulting from microwave absorption would reach to 1.9 dBm over the frequency range 6 GHz - 10 GHz when the samples are paved on a 10 cm  10 cm square aluminum plate with a thickness of about 0.35 mm.

Physical Characterization of BST with Different (x’) Ratios

2014 ◽  
Vol 487 ◽  
pp. 106-109
Author(s):  
Nurhafizah Ramli ◽  
Zaliman Sauli ◽  
Vithyacharan Retnasamy ◽  
They Yee Chin ◽  
K. Anwar ◽  
...  
Keyword(s):  
Thin Films ◽  
Surface Roughness ◽  
Strontium Titanate ◽  
Barium Strontium Titanate ◽  
Sol Gel ◽  
Force Microscopy ◽  
Atomic Force ◽  
Fields Of Study ◽  
Barium Strontium

Nowdays Barium strontium titanate (BST) can be applied into many fields of engineering. Its properties attracted more researchers to research and apply it into many fields of study. In this work, sol-gel method of preparing barium strontium titanate (BST) has been used. This work was done with 4 different ratio of x with 4 different deposition layers. The main purpose of this work is to investigate the relation between the ratio of barium (Ba) with different deposition layer and the surface of the substrate. Atomic force microscopy (AFM) was used in whole work to investigate the crystalline structure and surface roughness of the BST thin films.

scholarly journals Synthesis and Characterization of Nanostructure Tio2/Anthraquenone (AQ) Prepared by Sol-Gel Method

2017 ◽  
Vol 28 (1) ◽  
pp. 76
Author(s):  
Fadhela M. Hussein
Keyword(s):  
Sol Gel ◽  
X Ray Diffraction ◽  
First Order ◽  
Atomic Force ◽  
Rate Of Reaction ◽  
Ft Ir ◽  
Gel Technique ◽  
Uv Visible ◽  
Nano Titanium Dioxide

sol–gel technique conducted to synthesize nano titanium dioxide with anthraquenone (AQ) relatively in acidic pH. Nanoparticles were characterized using techniques like, Scanning Electrion Microscope (SEM), Atomic Force Microscope (AFM), UV-Visible Spectrioscopy, X-ray diffraction (XRD), Fourier transform infrared (FT-IR), SEM picture display that the TiO2/AQ is spherical in style, the band gap of TiO2/AQ nanoparticle is (3.05eV), BET and BJH analysis provides Pore volume and specific Surface area and the kinetic studie Suggest that the reaction is pseudo first order and the rate of reaction was reduce with rising initial concentration for p-Nitrotolune.

Sign in / Sign up

Export Citation Format

Share Document