Carbon Nanotubes Grafted with Hyperbranched Triazine Compounds

NANO ◽  
2015 ◽  
Vol 10 (01) ◽  
pp. 1550012 ◽  
Author(s):  
Tingting Li ◽  
Hongxia Yan ◽  
Tianye Liu ◽  
Chao Liu ◽  
Zhengyan Chen
Keyword(s):  
Carbon Nanotubes ◽  
Fourier Transform ◽  
Photoelectron Spectroscopy ◽  
Condensation Reaction ◽  
Resin Matrix ◽  
Tem Analysis ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Electron Microscopes

In order to improve the dispersibility of carbon nanotubes (CNTs) in the resin matrix, CNTs grafted with hyperbranched triazine compound (HPTC–CNTs) was produced by four generations condensation reaction using cyanuric chloride and hexamethylenediamine. Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), UV-Vis spectroscopy (UV-Vis) and transmission electron microscopes (TEM) were used to characterize the obtained HPTC–CNTs. The FTIR, XPS, UV-Vis and TEM analysis showed that CNTs had been successfully grafted with HPTC. The TGA showed that the content of HPTC on the surface of CNTs was about 58 wt.%. And the HPTC–CNTs had good dispersion both in water and acetone.

Highly active carbon nanotube–promoted Rh-Mn-Li/SiO2 catalysts for the synthesis of C2+ oxygenates from syngas

2021 ◽  
pp. 174751982098472
Author(s):  
Jun Yu ◽  
Ying Han ◽  
Guoqing Chen ◽  
Xiuzhen Xiao ◽  
Haifang Mao ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Photoelectron Spectroscopy ◽  
Co Hydrogenation ◽  
X Ray ◽  
Highly Active ◽  
Transmission Electron ◽  
Co Insertion ◽  
Temperature Programmed Surface Reaction ◽  
Temperature Programmed ◽  
Oxygenate Synthesis

The effect of carbon nanotubes on the catalytic properties of Rh-Mn-Li/SiO2 catalysts was investigated for CO hydrogenation. The catalysts were comprehensively characterized by means of X-ray power diffraction, N2 sorption, transmission electron microscope, H2–temperature-programmed reduction, CO–temperature-programmed desorption, temperature-programmed surface reaction, and X-ray photoelectron spectroscopy. The results showed that an appropriate amount of carbon nanotubes can be attached to the surface of the SiO2 sphere and can improve the Rh dispersion. Moderate Rh-Mn interaction can be obtained by doping with the appropriate amount of carbon nanotubes, which promotes the formation of strongly adsorbed CO and facilitates the progress of CO insertion, resulting in the increase in the selectivity of C2+ oxygenate synthesis.

scholarly journals Microwave-assisted preparation of ZnS and ZnSe nanocrystals with different morphologies for photodegradation process of organic dyes

2019 ◽  
Author(s):  
Katarzyna Matras-Postolek ◽  
A. Zaba ◽  
S. Sovinska ◽  
D. Bogdal
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Organic Dyes ◽  
Zinc Sulphide ◽  
Conventional Heating ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy

Zinc sulphide (ZnS) and zinc selenide (ZnSe) and manganese-doped and un-doped with different morphologies from 1D do 3D microflowers were successfully fabricated in only a few minutes by solvothermal reactions under microwave irradiation. In order to compare the effect of microwave heating on the properties of obtained  nanocrystals, additionally the synthesis under conventional heating was conducted additionally in similar conditions. The obtained nanocrystals were systematically characterized in terms of structural and optical properties using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance UV-Vis spectroscopy (DR UV-Vis), Fourier-transform infrared spectroscopy (FT-IR), photoluminescence spectroscopy (PL), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET) surface area analysis. The photocatalytic activity of ZnSe, ZnS, ZnS:Mn and ZnSe:Mn nanocrystals with different morphologies was evaluated by the degradation of methyl orange (MO) and Rhodamine 6G (R6G), respectively. The results show that Mn doped NCs samples had higher coefficient of degradation of organic dyes under ultraviolet irradiation (UV).

scholarly journals Surface Study of CuO Nanopetals by Advanced Nanocharacterization Techniques with Enhanced Optical and Catalytic Properties

Nanomaterials ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 1298 ◽  
Author(s):  
Muhammad Arif Khan ◽  
Nafarizal Nayan ◽  
Shadiullah Shadiullah ◽  
Mohd Khairul Ahmad ◽  
Chin Fhong Soon
Keyword(s):  
Photoelectron Spectroscopy ◽  
Catalytic Properties ◽  
Average Length ◽  
Tem Analysis ◽  
X Ray ◽  
Surface Study ◽  
Transmission Electron ◽  
One Step ◽  
Controlled Morphology ◽  
Xrd Patterns

In the present work, a facile one-step hydrothermal synthesis of well-defined stabilized CuO nanopetals and its surface study by advanced nanocharacterization techniques for enhanced optical and catalytic properties has been investigated. Characterization by Transmission electron microscopy (TEM) analysis confirmed existence of high crystalline CuO nanopetals with average length and diameter of 1611.96 nm and 650.50 nm, respectively. The nanopetals are monodispersed with a large surface area, controlled morphology, and demonstrate the nanocrystalline nature with a monoclinic structure. The phase purity of the as-synthesized sample was confirmed by Raman spectroscopy and X-ray diffraction (XRD) patterns. A significantly wide absorption up to 800 nm and increased band gap were observed in CuO nanopetals. The valance band (VB) and conduction band (CB) positions at CuO surface are measured to be of +0.7 and −1.03 eV, respectively, using X-ray photoelectron spectroscopy (XPS), which would be very promising for efficient catalytic properties. Furthermore, the obtained CuO nanopetals in the presence of hydrogen peroxide ( H 2 O 2 ) achieved excellent catalytic activities for degradation of methylene blue (MB) under dark, with degradation rate > 99% after 90 min, which is significantly higher than reported in the literature. The enhanced catalytic activity was referred to the controlled morphology of monodispersed CuO nanopetals, co-operative role of H 2 O 2 and energy band structure. This work contributes to a new approach for extensive application opportunities in environmental improvement.

Synthesis and Performance of Dopa-Modified Multiwalled Carbon Nanotubes

2012 ◽  
Vol 184-185 ◽  
pp. 1289-1293
Author(s):  
Lu Zhi Wang ◽  
Lin Yu ◽  
Xiao Ling Cheng ◽  
Jun He ◽  
Le Jia Lin ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Multiwalled Carbon Nanotubes ◽  
Photoelectron Spectroscopy ◽  
Multiwalled Carbon ◽  
X Ray ◽  
Multiwalled Nanotubes ◽  
Mixed Acid ◽  
Transmission Electron ◽  
Ft Ir ◽  
And Performance

The Dopamine-modified multiwalled carbon nanotubes (MWNT-Dopa) were synthesized by chemical reaction between dopamine (Dopa) and multiwalled carbon nanotubes which oxidazed by mixed-acid (MWNT-COOH). The structure of MWNT-Dopa were analyzed by Fourier transform infrared spectroscopy (FT-IR), Thermogravimetric (TG), Transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) techniques and the dispersity of MWNT-Dopa were studied by Dispersion stability analyzer. The results show that dopamine has been grafted on multiwalled carbon nanotubes successfully, and a dopamine layer which wraps on the surface of multiwalled nanotubes make multiwalled nanotubes have outstanding dispersity in water.

Preparation and Characterization of Carbon Nanotubes/Al2O3 Inorganic Hybrid Material - A Bio-Inspired Poly(Dopamine) Approach

2018 ◽  
Vol 54 ◽  
pp. 127-135
Author(s):  
Wen Zhao ◽  
Wen Cai Wang ◽  
Yong Lai Lu ◽  
Li Qun Zhang
Keyword(s):  
Carbon Nanotubes ◽  
Aqueous Solution ◽  
Photoelectron Spectroscopy ◽  
Oxidative Polymerization ◽  
The Self ◽  
Liquid Phase Deposition ◽  
X Ray ◽  
Transmission Electron ◽  
Cnts Surface

Carbon nanotubes/alumina (CNTs/Al2O3) nanocomposites were prepared by the poly (dopamine) assisted chemical liquid phase deposition (CLPD). The poly (dopamine) layers were firstly coated on the CNTs surface uniformly by the self-oxidative polymerization of dopamine in mild aqueous solution and then the Al2O3 nanoparticles formed on the poly (dopamine) coated CNTs surface by the CLPD. The hydrophilic poly (dopamine) layers on the CNTs surface can improve the dispersion of CNTs in aqueous solution. Moreover, it can be used as a key linker between the CNTs and Al2O3 because of the nitrogen-containing group in poly (dopamine) could coordinate with Al3+ ions. The as-prepared poly (dopamine) coated CNTs and CNTs/Al2O3 nanohybrids were characterized by X-ray photoelectron spectroscopy (XPS), X-radial diffractometer (XRD) and high resolution transmission electron microscopy (HRTEM). These results showed that the poly (dopamine) layers were coated on the surface of CNTs uniformly, and the Al2O3 nanoparticles embellished with the poly (dopamine) coated CNTs surface. Compared with pristine NR composites, the thermal conductivity of the as-prepared NR/CNTs@Al2O3 composites increased 17%.

scholarly journals Exploration of the Antimicrobial and Catalytic Properties of Gold Nanoparticles Greenly Synthesized by Cryptolepis buchanani Roem. and Schult Extract

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Kamonpan Wongyai ◽  
Phitchayapak Wintachai ◽  
Rasimate Maungchang ◽  
Parawee Rattanakit
Keyword(s):  
Staphylococcus Aureus ◽  
Gold Nanoparticles ◽  
Analytical Techniques ◽  
Average Diameter ◽  
Face Centered Cubic ◽  
Tem Analysis ◽  
X Ray ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Face Centered

A green, simple, and rapid synthesis of gold nanoparticles using plant extract, Cryptolepis buchanani Roem. and Schult, and their applications are first described in this paper. The formation of gold nanoparticles was visually observed by the appearance of a ruby red color, which was further indicated by an absorption peak at 530 nm in UV-Vis spectroscopy. Optimization of reaction parameters for the gold nanoparticles was also investigated. Various analytical techniques were employed as part of the process of characterizing the resulting gold nanoparticles. Fourier transform infrared (FTIR) analysis revealed that the phenol compounds present in the extract were responsible for gold(III) reduction and stabilization of gold nanoparticles. Transmission electron microscopy (TEM) analysis showed that the gold nanoparticles were spherical in shape with an average diameter of 11 nm. Powder X-ray diffraction (XRD) pattern indicated that the green synthesis approach produced highly crystalline, face-centered cubic gold nanoparticles. Energy-dispersive X-ray spectroscopy (EDS) measurements confirmed the presence of elemental gold in the prepared nanoparticles. The negative zeta potential value of gold nanoparticles was found to be -30.28 mV. The green synthesized gold nanoparticles expressed effective antibacterial activity against Staphylococcus aureus, methicillin-resistant Staphylococcus aureus, and Acinetobacter baumannii and exhibited an excellent catalytic property in terms of its reduction ability of methylene blue.

One-Pot Hydrothermal Synthesis of Sulfur-Doped SnO2 Nanoparticles and their Enhanced Photocatalytic Properties

NANO ◽  
2016 ◽  
Vol 11 (03) ◽  
pp. 1650035 ◽  
Author(s):  
Lin Ma ◽  
Limei Xu ◽  
Xuyao Xu ◽  
Xiaoping Zhou ◽  
Lingling Zhang
Keyword(s):  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Electrochemical Impedance ◽  
Sno2 Nanoparticles ◽  
Light Response ◽  
One Pot ◽  
X Ray ◽  
Transmission Electron ◽  
Light Region ◽  
Vis Spectroscopy

Sulfur-doped SnO2 nanoparticles with ultrafine sizes have been successfully prepared by a one-pot hydrothermal method. The obtained samples are characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), X-ray photoelectron spectroscopy (XPS), high resolution transmission electron microscopy (HRTEM), thermogravimetric (TG), analyzer UV-Vis spectroscopy, photoluminescence (PL) and electrochemical impedance spectroscopy (EIS). The experimental results indicate that the doping level of sulfur element as well as the bandgaps of SnO2 can be controlled to a certain extent by varying the amount of L-cysteine (L-cys). When evaluated as photocatalysts in the degradation of rhodamine B (RhB) and reduction of Cr(VI) under visible light region, the resultant sulfur-doped SnO2 nanoparticles demonstrate obviously enhanced photocatalytic activities due to the markedly improved visible light response and effective separation of the photo-generated electron–hole pairs.

Synthesis and Characteristics of Hierarchical Nanostructure Fe3O4 Coated Multi-Walled Carbon Nanotubes

2014 ◽  
Vol 926-930 ◽  
pp. 258-261
Author(s):  
Jing Heng Deng ◽  
Kan Ping Yu ◽  
Jian Guo Xie
Keyword(s):  
Electron Microscopy ◽  
Carbon Nanotubes ◽  
Photoelectron Spectroscopy ◽  
Solvothermal Process ◽  
X Ray ◽  
Hierarchical Nanostructure ◽  
Transmission Electron ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Scanning Electron

Hierarchical nanostructure Fe3O4/multi-walled carbon nanotubes (Fe3O4/MWCNTs) were prepared by solvothermal process using acid treated MWCNTs and iron acetylacetonate in ethylene glycol as reduction reagent. The materials were characterized using X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and Brunauer-Emmett-Teller (BET). The results showed that petal-like hierarchical Fe3O4 grew on MWCNTs and the Fe3O4 nanoparticles had diameters in the range of 55-110 nm. It was a facile approach to grow hierarchical nanoFe3O4.

Multi-wall carbon nanotubes with nitrogen-containing carbon coating

2013 ◽  
Vol 67 (8) ◽  
Author(s):  
Elena Tomšík ◽  
Zuzana Morávková ◽  
Jaroslav Stejskal ◽  
Miroslava Trchová ◽  
Petr Šálek ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Photoelectron Spectroscopy ◽  
Carbon Coating ◽  
Covalent Bonding ◽  
Inert Atmosphere ◽  
New Materials ◽  
X Ray ◽  
Multi Wall Carbon Nanotubes ◽  
Transmission Electron

AbstractPolyaniline coating was deposited on the surface of multi-wall carbon nanotubes of Russian and Taiwanese origin in situ during the polymerization of aniline. The deposited polyaniline film was subsequently carbonized under an inert atmosphere at various temperatures to produce coaxial coating of the carbon nanotubes with nitrogen-containing carbon. The new materials were investigated by infrared and Raman spectroscopies, which demonstrated the conversion of the polyaniline coating to a carbonized structure. X-ray photoelectron spectroscopy proved that the carbonized overlayer contains nitrogen atoms in various covalent bonding states. Transmission electron microscopy confirmed the coaxial structure of the composites. The Brunauer-Emmett-Teller method was used to estimate the specific surface area, the highest being 272 m2 g−1. The conductivity of 0.9–16 S cm−1 was measured by the four-point method, and it was only a little affected by the carbonization of the polyaniline coating.

SYNTHESIS OF GRAPHITE OXIDE (GO)/Cu2O NANOCOMPOSITE AND ITS CATALYTIC PERFORMANCE UNDER THE ULTRASOUND

NANO ◽  
2013 ◽  
Vol 08 (03) ◽  
pp. 1350032 ◽  
Author(s):  
CHUNNIAN CHEN ◽  
CHENWEI YU ◽  
WEN FU
Keyword(s):  
Fourier Transform ◽  
Electrostatic Interactions ◽  
Catalytic Performance ◽  
X Ray ◽  
Selective Area ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Ft Ir ◽  
Ir And Raman ◽  
Selective Area Electron Diffraction

GO/ Cu2O nanocomposite had been successfully synthesized by electrostatic interactions method. X-ray powder diffraction (XRD), transmission electron microscope (TEM), selective-area electron diffraction (SAED), Fourier transform infrared spectroscopy (FT-IR) and Raman spectra confirmed the structure of the Cu2O and GO/ Cu2O nanocomposite. The catalytic degradation of Rhodamine B under the condition of ultrasound was investigated and the result of UV-Vis spectroscopy demonstrated that the nanocomposite can efficiently degraded it.

Sign in / Sign up

Export Citation Format

Share Document