scholarly journals Energy Harvesting with Piezoelectric Element Using Vibroacoustic Coupling Phenomenon

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
Hiroyuki Moriyama ◽  
Hirotarou Tsuchiya ◽  
Yasuo Oshinoya
Keyword(s):  
Energy Harvesting ◽  
Electric Energy ◽  
Piezoelectric Element ◽  
Sound Field ◽  
Structural Vibrations ◽  
Acoustic Characteristics ◽  
Sound Fields ◽  
Plate Vibrations ◽  
Cylinder Length ◽  
Experimental Apparatus

This paper describes the vibroacoustic coupling between the structural vibrations and internal sound fields of thin structures. In this study, a cylindrical structure with thin end plates is subjected to the harmonic point force at one end plate or both end plates, and a natural frequency of the end plates is selected as the forcing frequency. The resulting vibroacoustic coupling is then analyzed theoretically and experimentally by considering the dynamic behavior of the plates and the acoustic characteristics of the internal sound field as a function of the cylinder length. The length and phase difference between the plate vibrations, which maximize the sound pressure level inside the cavity, are clarified theoretically. The theoretical results are validated experimentally through an excitation experiment using an experimental apparatus that emulates the analytical model. Moreover, the electricity generation experiment verifies that sufficient vibroacoustic coupling can be created for the adopted electricity generating system to be effective as an electric energy-harvesting device.

scholarly journals Parametrical Investigation of Piezoelectric Energy Harvesting via Friction-Induced Vibration

2020 ◽  
Vol 2020 ◽  
pp. 1-32
Author(s):  
D. W. Wang ◽  
M. X. Liu ◽  
W. J. Qian ◽  
X. Wu ◽  
Q. Ma ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Normal Load ◽  
Electric Energy ◽  
Piezoelectric Element ◽  
Degree Of Freedom ◽  
Piezoelectric Energy Harvesting ◽  
Force Factor ◽  
Stick Slip ◽  
Piezoelectric Energy ◽  
Friction Induced Vibration

In this work, piezoelectric energy harvesting performance via friction-induced vibration is investigated numerically. A one-degree-of-freedom friction system with a piezoelectric element is proposed, to study the piezoelectric energy harvesting via friction-induced stick-slip vibration. Subsequently, a two-degree-of-freedom friction system with two piezoelectric elements is proposed, to investigate the piezoelectric energy harvesting via model coupling vibration. Results show that regardless of the friction systems, it is feasible to convert friction-induced vibration energy to electrical energy when the friction system is operating in the unstable vibration region. Parametrical analysis indicates that for the one-degree-of-freedom friction system, when the normal load increases from 5 N to 30 N, the stick-slip motion becomes more intense, and the friction system will generate more electric energy. While for the two-degree-of-freedom friction system, with the normal load increase from 20 N to 120 N, there is a critical normal load value for the generation of the strongest vibration and the highest voltage output. When the velocity of the belt increases from 0.5 m/s to 2 m/s, the amplitudes of vibration and output voltage become larger. While with the velocity further increasing, the stick-slip motion and generated electric energy disappear. For both friction systems, the external electric resistance has no effect on the dynamic behaviour of the friction system; however, it can modify the output voltage amplitudes within limits. It is also found that when the force factor of piezoelectric element increases from 3.1 × 10−5 N/V to 3.1 × 10−3 N/V, the vibration and harvested energy gradually increase. When the force factor further increases to 3.1 × 10−2 N/V, the vibration reduces drastically and the corresponding output voltages reduce significantly, which proves that a piezoelectric element with an appropriated force factor can give the highest harvested energy and conversion efficiency.

Study on acoustic and flow-induced noise characteristics of L-shaped duct with a shallow cavity

2020 ◽  
Vol 68 (3) ◽  
pp. 209-225
Author(s):  
Masaaki Mori ◽  
Kunihiko Ishihara
Keyword(s):  
Air Conditioning ◽  
Sound Field ◽  
Frequency Range ◽  
Acoustic Characteristics ◽  
Inflow Velocity ◽  
Aerodynamic Sound ◽  
Noise Characteristics ◽  
Flow Induced Noise ◽  
Shallow Cavity ◽  
Conditioning Equipment

An aerodynamic sound generated by a flow inside a duct is one of the noise pro- blems. Flows in ducts with uneven surfaces such as grooves or cavities can be seen in various industrial devices and industrial products such as air-conditioning equipment in various plants or piping products. In this article, we have performed experiments and simulations to clarify acoustic and flow-induced sound characteris- tics of L-shaped duct with a shallow cavity installed. The experiments and simula- tions were performed under several inflow velocity conditions. The results show that the characteristics of the flow-induced sound in the duct are strongly affected by the acoustic characteristics of the duct interior sound field and the location of the shallow cavity. Especially, it was found that the acoustic characteristics were af- fected by the location of the shallow cavity in the frequency range between 1000 Hz and 1700 Hz.

scholarly journals Power-Generation Optimization Based on Piezoelectric Ceramic Deformation for Energy Harvesting Application with Renewable Energy

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2171
Author(s):  
Hyeonsu Han ◽  
Junghyuk Ko
Keyword(s):  
Power Generation ◽  
Renewable Energy ◽  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Ceramic ◽  
Piezoelectric Element ◽  
Piezoelectric Ceramics ◽  
Lead Zirconate ◽  
Piezoelectric Energy

Along with the increase in renewable energy, research on energy harvesting combined with piezoelectric energy is being conducted. However, it is difficult to predict the power generation of combined harvesting because there is no data on the power generation by a single piezoelectric material. Before predicting the corresponding power generation and efficiency, it is necessary to quantify the power generation by a single piezoelectric material alone. In this study, the generated power is measured based on three parameters (size of the piezoelectric ceramic, depth of compression, and speed of compression) that contribute to the deformation of a single PZT (Lead zirconate titanate)-based piezoelectric element. The generated power was analyzed by comparing with the corresponding parameters. The analysis results are as follows: (i) considering the difference between the size of the piezoelectric ceramic and the generated power, 20 mm was the most efficient piezoelectric ceramic size, (ii) considering the case of piezoelectric ceramics sized 14 mm, the generated power continued to increase with the increase in the compression depth of the piezoelectric ceramic, and (iii) For piezoelectric ceramics of all diameters, the longer the depth of deformation, the shorter the frequency, and depending on the depth of deformation, there is a specific frequency at which the charging power is maximum. Based on the findings of this study, PZT-based elements can be applied to cases that receive indirect force, including vibration energy and wave energy. In addition, the power generation of a PZT-based element can be predicted, and efficient conditions can be set for maximum power generation.

Multi-Stable Magnetic Spring-Based Energy Harvester Subject to Harmonic Excitation: Comparative Study and Experimental Evaluation

2018 ◽  
Author(s):  
Hieu Nguyen ◽  
Hamzeh Bardaweel
Keyword(s):  
Energy Harvesting ◽  
Kinetic Energy ◽  
Comparative Study ◽  
Experimental Evaluation ◽  
Chaotic Motion ◽  
Energy Harvester ◽  
Electric Energy ◽  
Harmonic Excitation ◽  
Jump Frequency ◽  
Piezoelectric Elements

The work presented here investigates a unique design platform for multi-stable energy harvesting using only interaction between magnets. A solid cylindrical magnet is levitated between two stationary magnets. Peripheral magnets are positioned around the casing of the energy harvester to create multiple stable positions. Upon external vibration, kinetic energy is converted into electric energy that is extracted using a coil wrapped around the casing of the harvester. A prototype of the multi-stable energy harvester is fabricated. Monostable and bistable configurations are demonstrated and fully characterized in static and dynamic modes. Compared to traditional multi-stable designs the harvester introduced in this work is compact, occupies less volume, and does not require complex circuitry normally needed for multi-stable harvesters involving piezoelectric elements. At 2.5g [m/s2], results from experiment show that the bistable harvester does not outperform the monostable harvester. At this level of acceleration, the bistable harvester exhibits intrawell motion away from jump frequency. Chaotic motion is observed in the bistable harvester when excited close to jump frequency. Interwell motion that yields high displacement amplitudes and velocities is absent at this acceleration.

Design and Construction of a Small Reverberation Chamber Applied to Absorption and Scattering Acoustic Measurements

2014 ◽  
Vol 1077 ◽  
pp. 197-202
Author(s):  
D. Hernandez ◽  
E.J. Liu ◽  
J.H. Huang ◽  
Y.C. Liu
Keyword(s):  
High Frequency ◽  
Integration Method ◽  
Sound Field ◽  
Acoustic Measurements ◽  
Acoustic Characteristics ◽  
Reverberation Chamber ◽  
Scattering Coefficients ◽  
Reverberation Chambers ◽  
The Cost ◽  
Design And Construction

Reverberation chambers are used to create a diffuse incidence sound field, where multiple types of acoustic measurements can be performed. The chambers tend to have a large volume in order to extent the reverberation time. However, this requirement may be conditioned by the cost and the infrastructure limitations. This paper presents the design and construction of a small-scaled reverberation chamber of 3 m3 for middle-high frequency acoustic measurements. On the design, the acoustic characteristics of chamber are confirmed via finite element computer simulation. As case studies, absorption and scattering coefficients of several materials and diffusors are measured. The reverberation times needed for the measurements were obtained by the impulse response integration method. The small reverberation chamber demonstrated to be a reliable tool for middle and high frequency acoustic measurements.

Concurrent Vibration Suppression and Energy Harvesting Using Ferrofluids: An Experimental Investigation

2014 ◽  
Author(s):  
Saad F. Alazemi ◽  
Amin Bibo ◽  
Mohammed F. Daqaq
Keyword(s):  
Magnetic Field ◽  
Power Generation ◽  
Energy Harvesting ◽  
Vibration Suppression ◽  
Design Parameters ◽  
Structural Vibrations ◽  
Rectangular Container ◽  
Fluid Damper ◽  
Magnetized Ferrofluid ◽  
Experimental Response

This paper presents an experimental study which examines the design parameters affecting the performance characteristics of a Tuned Magnetic Fluid Damper (TMFD) device designed to concurrently mitigate structural vibrations and harvest vibratory energy. The device which is mounted on a vibrating structure, consists of a rectangular container carrying a magnetized ferrofluid and a pick-up coil wound around the container to enable energy harvesting. Experiments are performed to investigate the three-way interaction between the vibrations of the structure, the sloshing of the fluid, and the harvesting circuit dynamics. In particular, the tuning and optimization is examined for several design parameters including magnetic field spatial distribution and intensity, winding direction, winding location, winding density, and ferrofluid height inside the tank. The experimental response of the device is compared against the conventional TMFD at different excitation levels and frequencies. Results demonstrating the influence of the significant parameters on the relative performance are presented and discussed in terms of vibration suppression and power generation capabilities.

scholarly journals Analysis of Double Elastic Steel Wind Driven Magneto-Electric Vibration Energy Harvesting System

Sensors ◽  
2021 ◽  
Vol 21 (21) ◽  
pp. 7364
Author(s):  
Yi-Ren Wang ◽  
Ming-Ching Chu
Keyword(s):  
Energy Harvesting ◽  
Electric Energy ◽  
Elastic Beam ◽  
Electrical Energy ◽  
Vibration Energy ◽  
Vibration Energy Harvesting ◽  
Concentrated Load ◽  
Single Beam ◽  
Piezoelectric Patch ◽  
Energy Harvesting System

This research proposes an energy harvesting system that collects the downward airflow from a helicopter or a multi-axis unmanned rotary-wing aircraft and uses this wind force to drive the magnet to rotate, generating repulsive force, which causes the double elastic steel system to slap each other and vibrate periodically in order to generate more electricity than the traditional energy harvesting system. The design concept of the vibration mechanism in this study is to allow the elastic steel carrying the magnet to slap another elastic steel carrying the piezoelectric patch to form a set of double elastic steel vibration energy harvesting (DES VEH) systems. The theoretical DES VEH mechanism of this research is composed of a pair of cantilever beams, with magnets attached to the free end of one beam, and PZT attached to the other beam. This study analyzes the single beam system first. The MOMS method is applied to analyze the frequency response of this nonlinear system theoretically, then combines the piezoelectric patch and the magneto-electric coupling device with this nonlinear elastic beam to analyze the benefits of the system’s converted electrical energy. In the theoretical study of the DES VEH system, the slapping force between the two elastic beams was considered as a concentrated load on each of the beams. Furthermore, both SES and DES VEH systems are studied and correlated. Finally, the experimental data and theoretical results are compared to verify the feasibility and correctness of the theory. It is proven that this DES VEH system can not only obtain the electric energy from the traditional SES VEH system but also obtain the extra electric energy of the steel vibration subjected to the slapping force, which generates optimal power to the greatest extent.

scholarly journals Possibilities of Energy Harvesting from the Suspension System of the Internal Combustion Engine in a Vehicle

2021 ◽  
Vol 23 (2) ◽  
pp. B106-B116
Author(s):  
Jacek Caban ◽  
Grzegorz Litak ◽  
Bartłomiej Ambrożkiewicz ◽  
Leszek Gardyński ◽  
Paweł Stączek ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Power Supply ◽  
Fossil Fuels ◽  
Combustion Engine ◽  
Electric Energy ◽  
Elastic Beam ◽  
Experimental Tests ◽  
Suspension System ◽  
Piezoelectric Energy ◽  
Mechanic Energy

The automotive industry faces huge challenge in environmental protection by reducing fossil fuels and energy consumption by developing various practical solutions in energy harvesting. The current analysis is related to the diesel engine power supply system in a passenger off-road vehicle for application of the piezoelectric energy harvesting system. Experimental tests were carried out for the three constant rotational speed values - 800, 1000 and 1500 rpm. The results pertained to operational and simulation tests of available power supply options from the engine suspension system in the vehicle, e.g. to power sensors supervising the engine’s operation or other small electrical devices in the vehicle. The simulations of output voltage were conducted by means of a nonlinear model with a resonator coupled to a piezoelectric elastic beam deformed in the magnetic field to improve the band of frequency transducing kinetic mechanic energy into electric energy.

scholarly journals EFFICIENT ACOUSTIC COMPOSITE PANELS BASED ON GRAPHITE

2021 ◽  
Vol 6 (4) ◽  
pp. 82-90
Author(s):  
E. Fanina
Keyword(s):  
Experimental Studies ◽  
Three Dimensional ◽  
Sound Field ◽  
Fire Retardant ◽  
Pyramidal Cells ◽  
Sound Insulation ◽  
Composite Panels ◽  
Thin Membrane ◽  
Reverberation Time ◽  
Acoustic Characteristics

A set of experimental studies is carried out to determine the acoustic characteristics of three-dimensional panels of fixed thickness made of carbon-based composite material installed in the opening between the reverberation chambers. Sound insulation indices are determined when they are excited by a diffuse sound field in wide frequency ranges. The reverberation time in model chambers with different partition configurations is calculated. The optimal configuration of the partition with pyramidal cells to reduce the reverberation time in the rooms is determined. The use of graphite in the form of thin membrane applied to various surfaces can significantly reduce the sound pressure levels in the room and increase the sound insulation indices of air noise. In addition to thin membrane, graphite can be used as an additive in composite materials for sound insulation purposes. It is shown that the characteristics of such panels are quite universal. The measured acoustic characteristics of composite panels are compared with similar characteristics of traditional materials. It is determined that the composition belongs to the I group of fire-retardant efficiency and can be recommended for use as a fire-retardant material. The developed acoustic material is an effective absorbing agent that solves problems in architectural acoustics, echo cancellation in construction and architecture. Similar to metamaterials, natural and artificial graphites allow to solve these problems with small volumes and masses using simple and inexpensive technologies.

scholarly journals A Fundamental Study for Design of Electric Energy Harvesting Device using PZT on the Road

2011 ◽  
Vol 13 (4) ◽  
pp. 159-166
Author(s):  
Jae-Jun Lee ◽  
Seung-Ki Ryu ◽  
Hak-Yong Moon ◽  
Soo-Ahn Kwon
Keyword(s):  
Energy Harvesting ◽  
Electric Energy ◽  
Fundamental Study ◽  
The Road ◽  
On The Road
Sign in / Sign up

Export Citation Format

Share Document