scholarly journals The Effects of Adding Elements of Zinc and Magnesium on Ag-Cu Eutectic Alloy for Warming Acupuncture

2013 ◽  
Vol 2013 ◽  
pp. 1-10
Author(s):  
Yu Kyoung Kim ◽  
Il Song Park ◽  
Keun Sik Kim ◽  
Min Ho Lee
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Physical And Mechanical Properties ◽  
Ternary Alloys ◽  
Suitable Material ◽  
Cu Alloys ◽  
Hyperthermia Therapy ◽  
Mg Addition ◽  
Composition Ratios ◽  
Potential Use

The warming acupuncture for hyperthermia therapy is made of STS304. However, its needle point cannot be reached to a desirable temperature due to heat loss caused by low thermal conductivity, and the quantification of stimulation condition and the effective standard establishment of warming acupuncture are required as a heat source. Accordingly, in this study, after Ag-Cu alloys with different composition ratios were casted and then mixed with additives to improve their physical and mechanical properties, the thermal conductivity and biocompatibility of the alloy specimens were evaluated for selecting suitable material. Ag-Cu binary alloys and ternary alloys added 5 wt% Zn or 2 wt% Mg were casted and then cold drawn to manufacture needles for acupuncture, and their physical properties, thermal conductivity, and biocompatibility were evaluated for their potential use in warming acupuncture. The results of this study showed that the physical and mechanical properties of the Ag-Cu alloys were improved by additives and that the thermal conductivity, machinability, and biocompatibility of the Ag-Cu alloys were improved by Mg addition.

BRUSH ALLOY 3

Alloy Digest ◽  
1983 ◽  
Vol 32 (3) ◽  
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Corrosion Resistance ◽  
Physical Properties ◽  
Copper Alloy ◽  
Elevated Temperatures ◽  
Physical And Mechanical Properties ◽  
Heat Treating ◽  
Good Resistance ◽  
Good Corrosion Resistance

Abstract BRUSH Alloy 3 offers the highest electrical and thermal conductivity of any beryllium-copper alloy. It possesses an excellent combination of moderate strength, good corrosion resistance and good resistance to moderately elevated temperatures. Because of its unique physical and mechanical properties, Brush Alloy 3 finds widespread use in welding applications (RWMA Class 3), current-carrying springs, switch and instrument parts and similar components. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fatigue. It also includes information on corrosion resistance as well as casting, forming, heat treating, machining, joining, and surface treatment. Filing Code: Cu-454. Producer or source: Brush Wellman Inc..

Cellulose Fibres as a Reinforcing Element in Building Materials

2017 ◽  
Author(s):  
Viola Hospodarova ◽  
Nadezda Stevulova ◽  
Vojtech Vaclavik ◽  
Tomas Dvorsky ◽  
Jaroslav Briancin
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Building Materials ◽  
Reference Sample ◽  
Physical And Mechanical Properties ◽  
Natural Fibre ◽  
Cement Composites ◽  
Cellulose Fibres ◽  
Cellulosic Fibres

Nowadays, construction sector is focusing in developing sustainable, green and eco-friendly building materials. Natural fibre is growingly being used in composite materials. This paper provides utilization of cellulose fibres as reinforcing agent into cement composites/plasters. Provided cellulosic fibres coming from various sources as bleached wood pulp and recycled waste paper fibres. Differences between cellulosic fibres are given by their physical characterization, chemical composition and SEM micrographs. Physical and mechanical properties of fibre-cement composites with fibre contents 0.2; 0.3and 0.5% by weight of filler and binder were investigated. Reference sample without fibres was also produced. The aim of this work is to investigate the effects of cellulose fibres on the final properties (density, water absorbability, coefficient of thermal conductivity and compressive strength) of the fibrecement plasters after 28 days of hardening. Testing of plasters with varying amount of cellulose fibres (0.2, 0.3 and 0.5 wt. %) has shown that the resulting physical and mechanical properties depend on the amount, the nature and structure of the used fibres. Linear dependences of compressive strength and thermal conductivity on density for plasters with cellulosic fibres adding were observed.

Synthesis, Characterization and Mechanical Properties of Silicon Carbide Nanowires

2010 ◽  
Author(s):  
Huan Zhang ◽  
Weiqiang Ding ◽  
Daryush Aidun
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Silicon Carbide ◽  
Physical And Mechanical Properties ◽  
High Hardness ◽  
High Strength ◽  
Harsh Environments ◽  
Low Density ◽  
Low Thermal Expansion ◽  
Oxidation And Corrosion

Silicon carbide (SiC) material has many outstanding physical and mechanical properties such as high strength, high hardness, low density, high thermal conductivity, low thermal expansion coefficient, large band-gap, and excellent oxidation and corrosion resistances [1–3]. It is a leading material for components and devices operating at high temperature, high power and under harsh environments [4–5]. Micro-sized SiC particles and whiskers are commonly used as reinforcement materials for ceramics, metals and alloys in various structural and tribological applications [6–7].

Thermal Insulation Particleboards Made with Wastes from Wood and Tire Rubber

2015 ◽  
Vol 668 ◽  
pp. 263-269 ◽  
Author(s):  
Marilia da Silva Bertolini ◽  
André Luis Christoforo ◽  
Francisco Antonio Rocco Lahr
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Thermal Insulation ◽  
Environmental Problem ◽  
Physical And Mechanical Properties ◽  
Modulus Of Rupture ◽  
Superior Performance ◽  
Tire Rubber ◽  
Polyurethane Resin

The concept of sustainable buildings addresses the environmentally efficiency, with respect to energy consumption, by adopting products that offer thermal insulation. Moreover, use of wastes from different materials also contributes to obtain products for this application. The volume of wastes from timber industry and those from tires are an environmental problem. This study aimed to production and characterization of particleboards using wastes from wood and tire rubber with castor-oil polyurethane resin. Panels were produced containing only wood and also with addition of tire rubber. The properties determined were density, modulus of rupture (MOR) and modulus of elasticity (MOE) in bending, according to Brazilian Code NBR 14810-3 (2006), and thermal conductivity. Statistical analysis was conducted in physical and mechanical properties. Panels containing wood were classified as low density (0.55 g/cm³), while those with wood and tire rubber resulted in medium density (0.78 g/cm³). For mechanical properties, the addition of rubber resulted in increased of MOR and reduction for MOE. Superior performance for thermal conductivity was achieved for panels produced only with wood. However, samples with a mixture of wood and tire rubber also showed consistent thermal conductivity with similar products. Considering the results obtained, panels containing wood and tire rubber addition have potential for application as thermal insulation.

scholarly journals Microstructures and Mechanical Properties of Al-2Fe-xCo Ternary Alloys with High Thermal Conductivity

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3728
Author(s):  
Gan Luo ◽  
Yujian Huang ◽  
Chengbo Li ◽  
Zhenghua Huang ◽  
Jun Du
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Fine Particles ◽  
Ternary Alloys ◽  
Thermal And Mechanical Properties ◽  
Free Electrons ◽  
Unmodified Alloy ◽  
Cast Alloys

The microstructures, mechanical properties, and thermal conductivity (TC) of Al-2Fe-xCo (x = 0~0.8) alloys in as-cast, homogeneous annealed, and cool rolled states are systematically studied. Results indicate that appropriate Co modification (x ≤ 0.5) simultaneously improves the thermal and mechanical properties of as-cast Al-2Fe alloys. The improvement of TC is attributed to ameliorating the morphology of primary Al3Fe phases from needles to short rods and fine particles, which decreases the scattering probability of free electrons during the electronic transmission. However, further increasing the Co content (x = 0.8) decreases the TC due to the formation of a coarse plate-like Al2FeCo phase. Besides, the thermal conductivity of annealed Al-2Fe-xCo alloys is higher than that of as-cast alloys because of the elimination of lattice defects and spheroidization of Al3Fe phases. After cool rolling with 80 % deformation, thermal conductivity of alloys slightly increases due to the breaking down of Al2FeCo phases. The rolled Al-2Fe-0.3Co alloy exhibits the highest thermal conductivity, which is about 225 W/(m·K), approximately 11 % higher than the as-cast Al-2Fe sample. The ultimate tensile strength (UTS) and elongation (EL) of as-cast Al-2Fe-0.5Co (UTS: 138 MPa; EL: 22.0 %) are increased by 35 % and 69 %, respectively, compared with those of unmodified alloy (UTS: 102 MPa; EL: 13.0 %).

scholarly journals Carbon nanomaterials enhanced cement-based composites: advances and challenges

2020 ◽  
Vol 9 (1) ◽  
pp. 115-135 ◽  
Author(s):  
Mingrui Du ◽  
Hongwen Jing ◽  
Yuan Gao ◽  
Haijian Su ◽  
Hongyuan Fang
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Graphene Oxide ◽  
Ordinary Portland Cement ◽  
Carbon Nanomaterials ◽  
Physical And Mechanical Properties ◽  
Comprehensive Review ◽  
Reduced Graphene ◽  
Cement Based Materials ◽  
Graphene Nanoplates

AbstractCarbon nanomaterials, predominantly carbon nanofibers, carbon nanotubes, graphene, graphene nanoplates, graphene oxide and reduced graphene oxide, possess superior chemical, physical and mechanical properties. They have been successfully introduced into ordinary Portland cement to give enhancements in terms of mechanical properties, durability and electrical/thermal conductivity, and to modify the functional properties, converting conventional cement-based materials into stronger, smarter and more durable composites. This paper provides a comprehensive review of the properties of carbon nanomaterials, current developments and novel techniques in carbon nanomaterials enhanced cement-based composites (CN-CBCs). Further study of the applications of CN-CBCs at industrial scale is also discussed.

scholarly journals Adequate Correlation between the Physical and Mechanical Properties of Glass Foam

2021 ◽  
Vol 1 (4) ◽  
pp. 14-26
Author(s):  
Lucian Paunescu ◽  
Sorin Mircea Axinte ◽  
Marius Florin Dragoescu ◽  
Felicia Cosmulescu
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Thermal Insulation ◽  
Coal Fly Ash ◽  
Physical And Mechanical Properties ◽  
Ceramic Foam ◽  
Glass Waste ◽  
Glass Foam

The paper presents experimental results obtained in the manufacturing process of a glass foam by adequate correlation between its physical and thermal properties (density, porosity, thermal conductivity) and mechanical (compressive strength) by a slight controlled overheating of the foamed material. Using a powder mixture of glass waste (87-91.5 %), coal fly ash (3-9 %) and silicon carbide (4-5.5 %) microwave heated at 935-975 ºC by this unconventional technique, constituting the originality of the work, was obtained a glass-ceramic foam with moderate compressive strength (1.8-2.6 MPa) and very low thermal conductivity (0.058-0.070 W/m·K). The material overheating generated a homogeneous porous structure characterized by closed cells with relatively large dimensions (without the tendency to join neighboring cells) making it difficult to transfer heat across the material. The foamed product is suitable for the manufacture of thermal insulation blocks for the inner or outer walls of the building without excessive mechanical stress, being an advantageous alternative by comparison with known types of polymeric or fiberglass thermal insulation materials.

scholarly journals Silicon dioxide dispersed effects on some physical and mechanical properties of Al2Si2O5(OH)4

2021 ◽  
Vol 2114 (1) ◽  
pp. 012021
Author(s):  
Tarik T. Issa ◽  
Noor Kadhum Abid ◽  
Mustafa Kadhum Abid
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Grain Size ◽  
Silicon Dioxide ◽  
Compression Strength ◽  
Sintered Density ◽  
Physical And Mechanical Properties ◽  
Linear Shrinkage ◽  
Weight Percentage ◽  
The Common

Abstract Kaolin and silica of 50 μm grain size were used in different weight percentage. Four combinations have been selected as green compacted bodies. Different sintering temperatures ranging from (1000 – 1400) °C were used to sintered all the combinations under static air. The sintered density, thermal conductivity compression strength and linear shrinkage were tested after sintering. The common behavior indicated that the improvement with its optimum results was found at the combination (Kaolin 20-SiO2 80) Wt. %, sintered at 1400 °C, for 3 hours under static air.

scholarly journals Optimization of Cellular Concrete Formulation with Aluminum Waste and Mineral Additions

2021 ◽  
Vol 7 (7) ◽  
pp. 1222-1234
Author(s):  
Mohammed Salah Bouglada ◽  
Noui Ammar ◽  
Belagraa Larbi
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Sand Dunes ◽  
Physical And Mechanical Properties ◽  
Experimental Program ◽  
Mechanical Resistance ◽  
Dune Sand ◽  
Mineral Additions ◽  
Cellular Concrete

The paper aims to study cellular concrete with a new approach of formulation without an autoclave, with the use of aluminum waste and incorporation of mineral additions into the sand and evaluate its physical and mechanical properties. In this experimental study, two types of cellular concrete are prepared, based on crushed and dune sand with the incorporation of 15% of the slag and 10% of pozzolana, as sand replacement. An experimental program was performed to determine the compressive strength at 28 days, the density and thermal conductivity of the confected cellular concrete. The obtained results showed that concretes prepared with crushed sand developed better mechanical resistance compared to the dune sand. It is also noted that the concretes containing the mineral additions provide a substantial increase in compressive strength in particular slag. Furthermore, cellular concretes with sand dunes offer better thermal conductivity, compared to those with crushed sand. The use of the additions reduces the Water/Binder (W/B) ratio and leads to a lower thermal conductivity regardless of the used sand nature. The outcome of the present study here in could present a modest contribution for the production of cellular concrete with local materials in particular dune sand, active mineral addition and aluminum waste. The physical and mechanical properties obtained from this new composition are estimated acceptable compared to those of the industry-prepared cellular concrete product. Doi: 10.28991/cej-2021-03091721 Full Text: PDF

Sign in / Sign up

Export Citation Format

Share Document