scholarly journals A Study on the Bond Behavior of Corroded Reinforced Concrete Containing Recycled Aggregates

2015 ◽  
Vol 2015 ◽  
pp. 1-9 ◽  
Author(s):  
Haifeng Yang ◽  
Zhiheng Deng ◽  
Yinghong Qin ◽  
Liangsheng Lv
Keyword(s):  
Reinforced Concrete ◽  
Bond Strength ◽  
High Strength ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Bond Slip ◽  
Rebar Corrosion ◽  
Ultimate Bond Strength

This paper investigated bond-slip characteristics of chloride-induced corroded reinforced concrete incorporating different levels of recycled concrete aggregates (RCA). Pullout tests were adopted to evaluate the bonding and debonding behaviors of the embedded rebar experiencing different corrosion levels. Both high- and low-strength concrete were considered. Bond-slip curves were recorded to determine the influences of rebar corrosion levels and RCA replacements on the bond strength and debonding energy of the specimens. Test results indicate that increasing rebar corrosion level gradually weakens the antisliding ability of reinforced recycled aggregate concrete (RAC) except for a small level corrosion and the degradation rate of ultimate bond strength increases with a decrease of compressive strength at 0.5% rebar corrosion. The results also demonstrate that the ultimate bond strength of reinforced RAC slightly decreases with an increase of RCA replacement. However, the relative bond strength between uncorroded rebar and RAC is little affected by RCA content, while it decreases with an increase of RCA replacement in high-strength specimens after rebar corrosion. The debonding energy between deformed rebar and RAC is found decreasing with the increment of the rebar corrosion level and increasing with an increase of RAC content.

Mechanical Research on Bond-Slip Behaviors of Recycled Aggregate Concrete-Filled Square Steel Tubes

2012 ◽  
Vol 166-169 ◽  
pp. 3233-3236 ◽  
Author(s):  
Jun Tao Li ◽  
Jin Jun Xu ◽  
Zong Ping Chen ◽  
Yi Li ◽  
Ying Liang
Keyword(s):  
Bond Strength ◽  
Concrete Strength ◽  
Steel Tube ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Replacement Rate ◽  
Steel Tubes ◽  
Aggregate Concrete ◽  
Bond Slip ◽  
Ultimate Bond Strength

In order to research the interface bond-slip behaviors of recycled aggregate concrete-filled square steel tube (RACFSST), ten specimens using waste concrete were designed for launch test. The three changing parameters were concrete strength grade, embedded length and recycled coarse aggregate replacement rate. The load–slip curves of square steel tubes and recycled aggregate concrete were obtained, and starting bond strength and ultimate bond strength influenced by each changing parameter were analyzed. The results show that the replacement rate had a slight influence on the starting bond strength and ultimate bond strength, while the embedded length had the opposite effect. The shorter embedded length specimens had larger bond strength. The concrete strength had a relatively large influence on them.

Microstructural Features of Recycled Aggregate Concrete: From Non-Structural to High-Performance Concrete

2019 ◽  
Vol 25 (3) ◽  
pp. 601-616 ◽  
Author(s):  
Diogo Pedro ◽  
Mafalda Guedes ◽  
Jorge de Brito ◽  
Luís Evangelista
Keyword(s):  
High Performance ◽  
Mechanical Performance ◽  
High Performance Concrete ◽  
Concrete Strength ◽  
High Strength ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Sequential Approach

AbstractThe use of concrete-recycled aggregates to produce high-performance concrete is limited by insufficient correlation between resulting microstructure and its influence on mechanical performance reproducibility. This work addresses this issue in a sequential approach: concrete microstructure was systematically analyzed and characterized by scanning electron microscopy and results were correlated with concrete compressive strength and water absorption ability. The influence of replacing natural aggregates (NA) with recycled concrete aggregates (RCA), with different source concrete strength levels, of silica fume (SF) addition and of mixing procedure was tested. The results show that the developed microstructure depends on the concrete composition and is conditioned by the distinct nature of NA, recycled aggregates from high-strength source concrete, and recycled aggregates from low-strength source concrete. SF was only effective at concrete densification when a two-stage mixing approach was used. The highest achieved strength in concrete with 100% incorporation of RCA was 97.3 MPa, comparable to that of conventional high-strength concrete with NA. This shows that incorporation of significant amounts of RCA replacing NA in concrete is not only a realistic approach to current environmental goals, but also a viable route for the production of high-performance concrete.

scholarly journals Verification of a Torsional Behaviour Prediction Model for Reinforced Recycled Aggregate Concrete Beams

2022 ◽  
Vol 2022 ◽  
pp. 1-13
Author(s):  
Aqeel H. Chkheiwer ◽  
Mazin A. Ahmed ◽  
Zahir M. N. Hassan
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Reinforced Concrete Beams ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Cross Sectional ◽  
Recycled Concrete Aggregates ◽  
Concrete Recycling

This study shows the torsional conduct of aggregate streaming beams of reinforced concrete recycling. Pure torsion was perceived for 15 reinforced concrete beams containing recycled concrete aggregates. The beams were grouped into five lengths and cross-sectional groups. The study’s principal parameters were the various percentages of longitudinal steel reinforcement and the proportions of recycled aggregates. The beams were purely twisted until failure and investigated for torsional and crack behaviour. The findings show that the beams with maximum steel enhancement and standard aggregate exhibited maximum cracking power and ultimate torsional strength. Recycled aggregates increased the presence of splitting and the ultimate strength, and the effects of steel strengthening in recycled beams were apparent. In a second analysis, the whole torsional reaction of the beams was analytically predicted. A soft truss model was used and matched with test results for standard beams. A strong compromise was generally reached.

scholarly journals Discrete Element Simulation Analysis of Biaxial Mechanical Properties of Concrete with Large-Size Recycled Aggregate

2021 ◽  
Vol 13 (13) ◽  
pp. 7498
Author(s):  
Tan Li ◽  
Jianzhuang Xiao
Keyword(s):  
Mechanical Properties ◽  
Stress State ◽  
Strain Curve ◽  
Confining Pressure ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Aggregate Model ◽  
Large Size

Concrete made with large-size recycled aggregates is a new kind of recycled concrete, where the size of the recycled aggregate used is 25–80 mm, which is generally three times that of conventional aggregate. Thus, its composition and mechanical properties are different from that of conventional recycled concrete and can be applied in large-volume structures. In this study, recycled aggregate generated in two stages with randomly distributed gravels and mortar was used to replace the conventional recycled aggregate model, to observe the internal stress state and cracking of the large-size recycled aggregate. This paper also investigated the mechanical properties, such as the compressive strength, crack morphology, and stress–strain curve, of concrete with large-size recycled aggregates under different confining pressures and recycled aggregate incorporation ratios. Through this research, it was found that when compared with conventional concrete, under the confining pressure, the strength of large-size recycled aggregate concrete did not decrease significantly at the same stress state, moreover, the stiffness was increased. Confining pressure has a significant influence on the strength of large-size recycled aggregate cocrete.

scholarly journals Studies on Hemp and Recycled Aggregate Concrete

2020 ◽  
Vol 14 (1) ◽  
Author(s):  
Samer Ghosn ◽  
Nour Cherkawi ◽  
Bilal Hamad
Keyword(s):  
Mechanical Properties ◽  
Fiber Length ◽  
Plain Concrete ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Silane Treatment ◽  
Hemp Fiber ◽  
Fiber Treatment

Abstract This paper reports on the first phase of a multi-phase research program conducted at the American University of Beirut (AUB) on “Hemp and Recycled Aggregates Concrete” (HRAC). HRAC is a new sustainable concrete material where hemp fibers are incorporated in the mix, the coarse aggregate content is reduced by 20% of the concrete volume, and 50% of the natural coarse aggregates (NCA) are replaced by recycled concrete aggregates (RCA), thus saving on natural resources and addressing the problem of waste material disposal. The effect of the new material on concrete consistency and hardened mechanical properties was studied. Also, few durability tests were conducted. Variables included percentage replacement of NCA by RCA (0 or 50%), maximum size aggregate (10 or 20 mm), hemp fiber length (20 or 30 mm), and hemp fiber treatment (alkali or silane or acetyl). Fiber characterization tests were conducted including morphology, crystallinity, and thermal analysis. The tests indicated that alkali and acetyl fiber treatments were better than the silane treatment in removing impurities on the fiber surface. Also, alkali and acetyl treatments have increased the crystallinity of the fibers while silane treatment decreased it. Results of mechanical properties tests showed that while HRAC has considerable lower compressive strength and modulus of elasticity than plain concrete, the flexural strength and splitting tensile strength are not significantly affected. The flexural stress–strain behavior of HRAC is ductile as compared to the brittle behavior of the plain concrete beams indicating positive impact on toughness and energy dissipation. The durability tests indicated that whereas HRAC mixes have higher absorption than plain concrete, they have better thermal properties and their resistance to freeze–thaw cycles is comparable to plain concrete. All test results were not significantly affected by fiber length or fiber treatment.

Experimental Study on Compressive Strength of Recycled Aggregate Concrete with Different Replacement Ratios

2012 ◽  
Vol 174-177 ◽  
pp. 1277-1280 ◽  
Author(s):  
Hai Yong Cai ◽  
Min Zhang ◽  
Ling Bo Dang
Keyword(s):  
Experimental Study ◽  
Compressive Strength ◽  
Failure Mode ◽  
Failure Process ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Replacement Ratio ◽  
Aggregate Concrete

Compressive strengths of recycled aggregate concrete(RAC) with different recycled aggregates(RA) replacement ratios at 7d, 28d, 60d ages are investigated respectively. Failure process and failure mode of RAC are analyzed, influences on compressive strength with same mix ratio and different RA replacement ratios are analyzed, and the reason is investigated in this paper. The experimental results indicate that compressive strength of recycled concrete at 28d age can reach the standard generally, it is feasible to mix concrete with recycled aggregates, compressive strength with 50% replacement ratio is relatively high.

scholarly journals Experimental Characterization of Prefabricated Bridge Deck Panels Prepared with Prestressed and Sustainable Ultra-High Performance Concrete

2020 ◽  
Vol 10 (15) ◽  
pp. 5132
Author(s):  
Muhammad Naveed Zafar ◽  
Muhammad Azhar Saleem ◽  
Jun Xia ◽  
Muhammad Mazhar Saleem
Keyword(s):  
High Performance ◽  
Bridge Deck ◽  
High Performance Concrete ◽  
High Strength ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Ultra High Performance Concrete ◽  
Aggregate Concrete ◽  
Deck Panels

Enhanced quality and reduced on-site construction time are the basic features of prefabricated bridge elements and systems. Prefabricated lightweight bridge decks have already started finding their place in accelerated bridge construction (ABC). Therefore, the development of deck panels using high strength and high performance concrete has become an active area of research. Further optimization in such deck systems is possible using prestressing or replacement of raw materials with sustainable and recyclable materials. This research involves experimental evaluation of six full-depth precast prestressed high strength fiber-reinforced concrete (HSFRC) and six partial-depth sustainable ultra-high performance concrete (sUHPC) composite bridge deck panels. The composite panels comprise UHPC prepared with ground granulated blast furnace slag (GGBS) with the replacement of 30% cement content overlaid by recycled aggregate concrete made with replacement of 30% of coarse aggregates with recycled aggregates. The experimental variables for six HSFRC panels were depth, level of prestressing, and shear reinforcement. The six sUHPC panels were prepared with different shear and flexural reinforcements and sUHPC-normal/recycled aggregate concrete interface. Experimental results exhibit the promise of both systems to serve as an alternative to conventional bridge deck systems.

scholarly journals A Study Based upon the Usage Recycled Aggregate to Enhance the Strength Aspects of Conventional Concrete: A Critical Review

2021 ◽  
Vol 9 (VI) ◽  
pp. 1567-1570
Author(s):  
Suhail Mushtaq Khan
Keyword(s):  
Chloride Ions ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Concrete Aggregate ◽  
Split Tensile Strength ◽  
Conventional Concrete ◽  
Natural Aggregate ◽  
Concrete Production

Recycled aggregates are those crushed cement concrete or asphalt pavement which comes out from the construction debris which is reused in construction. They are made from the reprocessing of materials which have been used in previous constructions. This paper discusses about the study of properties of recycled aggregates from the sources which has already been published. The results are that 100% replacement of natural aggregate by recycled concrete aggregate effect on chloride ions resistance, it plays negative effects on durability of recycled concrete aggregates, and addition of fiber in recycled aggregate concrete mixture gave more effective in the performance of concrete. On experimental study of recycled aggregate, compressive, flexural and split tensile strength of the recycled aggregate were found to be lower than that of the natural aggregate. Use of recycled aggregate in a new concrete production is still limited. Recommendation of introduction of recycled aggregates standard is required for the materials to be used successfully in future. Gaps in literature reviews are also included in this paper.

scholarly journals Call for papers on special issue “Performance-based Service Life Design of reinforced recycled aggregate concrete”

2020 ◽  
Vol 2 (1) ◽  
pp. 045-045
Keyword(s):  
Reinforced Concrete ◽  
Service Life ◽  
Chloride Ion ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Special Issue ◽  
Aggregate Concrete ◽  
Service Life Design ◽  
Life Design

Aim & Scope: Sustainability requires a judicious use of natural resources. Reducing the consumption of natural aggregates and ensuring adequate durability of reinforced concrete infrastructures are major steps towards sustainability. Performance-based Service Life Design and recycled aggregate concrete are intense research fields. Considering the research maturity of each subject on its own, it is time to couple them and deliver knowledge on performance-based Service Life Design for reinforced concrete structures incorporating recycled aggregates. This Special Issue of Materials International constitutes a way to disseminate results and findings from original studies, experimental programs, empirical, analytical and numerical modelling of initiation period (carbonation- and chloride ion-related), propagation period or both (service life). Probabilistic, semi-probabilistic and deterministic approaches are welcome.

scholarly journals Performance of Recycled Aggregate Concrete for M25 Grade Concrete

2019 ◽  
Vol 9 (2) ◽  
pp. 4694-4700
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Recycled Aggregates ◽  
Aggregate Concrete ◽  
Inorganic Particles ◽  
Natural Aggregates

Recycled aggregates (RCA) are the aggregates which are made up of crushed, inorganic particles that are obtained from the construction demolition debris. Now a day’s protection of environment is the ultimate challenge to the society. So the usage of RCA’s is the best alternative for the aggregates which are obtained naturally in the construction activity. The scope of using these recycled concrete aggregates is increasing day by day. It reduces the cost effectively as we are using waste concrete as recycled aggregates. The main focus of this paper is to use find the strength qualities of recycled aggregates so as to use it as an alternative for the natural aggregates in high strength concrete for various construction activities. Comparison of workability, compressive strength, tensile strength, elastic modulus and flexural strength of recycled aggregate concrete is made with natural aggregate concrete. Here M25 grade concrete is taken and the natural aggregates were replaced with recycled aggregates in various percentages of 0%, 25%, 50%, 75% and 100%. The mix design for these replacement ratios are done by using code of IS 10262-2009. In order to determine the properties which were mentioned above a total of 60 cubes, 10 beams and 40 cylinders were casted. The compressive strength and tensile strength of RCA concrete have been determined for 7 days and 28 days where as the modulus of elasticity and the flexural strength of RCA concrete are determined after curing for the period of 28 days. The tests done on RCA concrete are compared with concrete which is obtained by natural aggregates As per IS codification the parameters which were determined are reducing moderately as the amount of aggregates which are recycled is being raised

Sign in / Sign up

Export Citation Format

Share Document