scholarly journals Numerical Simulation of Interaction between Hall Thruster CEX Ions and SMART-1 Spacecraft

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Kang Shan ◽  
Yuchuan Chu ◽  
Qingyu Li ◽  
Liang Zheng ◽  
Yong Cao
Keyword(s):  
Numerical Simulation ◽  
Heat Flux ◽  
Thermal Loading ◽  
Three Dimensional ◽  
Hall Thruster ◽  
Solar Array ◽  
Thermal Heating ◽  
Main Thrust ◽  
Solar Arrays ◽  
Simulation Results

The interaction between the plume of Hall thruster and the surface of the SMART-1 spacecraft is investigated by developing a three-dimensional IFE-PIC-MCC code, with the emphasis on the effect of the disturbance force and thermal loading caused by charge exchange ions (CEX) impingement on the surface of the spacecraft. The parameters such as heat flux and forces of CEX ions which impinge on SMART-1 and solar arrays are obtained. The disturbance force of CEX ions to the spacecraft is calculated for different divergence angles and different solar array rotation cases. The simulation results show that the disturbance force and heat flux on spacecraft change very little as the divergence angle changes. The effect of maximum disturbance force can be neglected since it is so small comparing with the nominal value of the main thrust. Solar arrays receive the least thermal heating from the CEX ions when the beam ions flow is perpendicular to the solar array plane.

Numerical Simulation Of A Microchannel For Microelectronic Cooling

2012 ◽  
Author(s):  
Wai Hing Wong ◽  
Normah Mohd. Ghazali
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Heat Flux ◽  
Aspect Ratio ◽  
Three Dimensional ◽  
Large Temperature ◽  
Rectangular Microchannel ◽  
Numerical Work ◽  
Solid Region ◽  
Wall Interaction

Kertas kerja ini membincangkan simulasi berangka ke atas sinki haba saluran mikro dalam penyejukan alatan mikroelektronik. Model Dinamik Bendalir Berkomputer (CFD) tiga dimensi dibina menggunakan pakej komersil, FLUENT, untuk mengkaji fenomenon aliran bendalir dan pemindahan haba konjugat di dalam suatu sinki haba segi empat yang diperbuat daripada silikon. Model ditentusahkan dengan keputusan daripada uji kaji dan pengkajian berangka yang lepas untuk lingkungan nombor Reynolds kurang daripada 400 berdasarkan diameter hidraulik 86 mm. Kajian ini mengambil kira kesan kelikatan bendalir yang bersandaran dengan suhu dan keadaan aliran pra–membangun dari segi hidrodinamik dan haba. Model memberi maklumat tentang taburan suhu dan fluks haba yang terperinci di dalam sinki haba saluran mikro. Kecerunan suhu yang tinggi dicatat pada kawasan pepejal berdekatan dengan sumber. Fluks haba paling tinggi didapati pada dinding tepi saluran mikro diikuti oleh dinding atas dan bawah. Purata pekali pemindahan haba yang lebih tinggi bagi silikon menjadikan ia bahan binaan sinki haba saluran mikro yang lebih baik berbanding dengan kuprum dan aluminium. Peningkatan nisbah aspek saluran mikro yang bersegi empat memberi kecekapan penyejukan yang lebih tinggi kerana kelebaran saluran yang berkurangan memberi kecerunan halaju yang lebih tinggi dalam saluran. Nisbah aspek yang optimum yang diperoleh adalah dalam lingkungan 3.7 – 4.1. Kata kunci: Saluran mikro, CFD, FLUENT, simulasi berangka, penyejukan mikroelektron The paper discusses the numerical simulation of a micro–channel heat sink in microelectronics cooling. A three–dimensional Computational Fluid Dynamics (CFD) model was built using the commercial package, FLUENT, to investigate the conjugate fluid flow and heat transfer phenomena in a silicon–based rectangular microchannel heatsink. The model was validated with past experimental and numerical work for Reynolds numbers less than 400 based on a hydraulic diameter of 86 mm. The investigation was conducted with consideration of temperaturedependent viscosity and developing flow, both hydrodynamically and thermally. The model provided detailed temperature and heat flux distributions in the microchannel heatsink. The results indicate a large temperature gradient in the solid region near the heat source. The highest heat flux is found at the side walls of the microchannel, followed by top wall and bottom wall due to the wall interaction effects. Silicon is proven to be a better microchannel heatsink material compared to copper and aluminum, indicated by a higher average heat transfer. A higher aspect ratio in a rectangular microchannel gives higher cooling capability due to high velocity gradient around the channel when channel width decreases. Optimum aspect ratio obtained is in the range of 3.7 – 4.1. Key words: Microchannel, CFD, FLUENT, numerical simulation, microeletronics cooling

scholarly journals MEMS-Based Integrated Triaxial Electrochemical Seismometer

Micromachines ◽  
2021 ◽  
Vol 12 (10) ◽  
pp. 1156
Author(s):  
Wenjie Qi ◽  
Bowen Liu ◽  
Tian Liang ◽  
Jian Chen ◽  
Deyong Chen ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Ground Motion ◽  
Small Volume ◽  
Three Dimensional ◽  
Experimental Results ◽  
Good Prospect ◽  
High Symmetry ◽  
Noise Levels ◽  
Sensitivity Curves ◽  
Simulation Results

This paper presents a micro-electromechanical systems (MEMS)-based integrated triaxial electrochemical seismometer, which can detect three-dimensional vibration. By integrating three axes, the integrated triaxial electrochemical seismometer is characterized by small volume and high symmetry. The numerical simulation results inferred that the integrated triaxial electrochemical seismometer had excellent independence among three axes. Based on the experimental results, the integrated triaxial electrochemical seismometer had the advantage of small axial crosstalk and could detect vibration in arbitrary directions. Furthermore, compared with the uniaxial electrochemical seismometer, the integrated triaxial electrochemical seismometer had similar sensitivity curves ranging from 0.01 to 100 Hz. In terms of random ground motion response, high consistencies between the developed integrated triaxial electrochemical seismometer and the uniaxial electrochemical seismometer could be easily observed, which indicated that the developed integrated triaxial electrochemical seismometer produced comparable noise levels to those of the uniaxial electrochemical seismometer. These results validated the performance of the integrated triaxial electrochemical seismometer, which has a good prospect in the field of deep geophysical exploration and submarine seismic monitoring.

Numerical Simulation of the Kinetic Energy Projectile Oblique Penetration into the Concrete

2014 ◽  
Vol 989-994 ◽  
pp. 982-985
Author(s):  
Jun Chen ◽  
Xiao Jun Ye
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Kinetic Energy ◽  
Three Dimensional ◽  
Test Results ◽  
Destruction Process ◽  
3D Finite Element ◽  
Finite Element Software ◽  
Simulation Results ◽  
Target Characteristics

ANSYS-LS/DYNA 3D finite element software projectile penetrating concrete target three-dimensional numerical simulation , has been the target characteristics and destroy ballistic missile trajectory , velocity and acceleration and analyze penetration and the time between relationship , compared with the test results , the phenomenon is consistent with the simulation results. The results show that : the destruction process finite element software can better demonstrate concrete tests revealed the phenomenon can not be observed , estimated penetration depth and direction of the oblique penetration missile deflection .

scholarly journals Study on Fluorine Pollution in a Slag Yard

2019 ◽  
Vol 9 (5) ◽  
pp. 847
Author(s):  
Lide Wei ◽  
Changfu Wei ◽  
Sugang Sui
Keyword(s):  
Numerical Simulation ◽  
Experimental Investigation ◽  
Numerical Simulations ◽  
Solute Transport ◽  
Large Scale ◽  
Three Dimensional ◽  
Simulation Method ◽  
Laboratory Studies ◽  
Survey Results ◽  
Simulation Results

This paper suggests a large-scale three-dimensional numerical simulation method to investigate the fluorine pollution near a slag yard. The large-scale three-dimensional numerical simulation method included an experimental investigation, laboratory studies of solute transport during absorption of water by soil, and large-scale three-dimensional numerical simulations of solute transport. The experimental results showed that the concentrations of fluorine from smelting slag and construction waste soil were well over the discharge limit of 0.1 kg/m3 recommended by Chinese guidelines. The key parameters of the materials used for large-scale three-dimensional numerical simulations were determined based on an experimental investigation, laboratory studies, and soil saturation of survey results and back analyses. A large-scale three-dimensional numerical simulation of solute transport was performed, and its results were compared to the experiment results. The simulation results showed that the clay near the slag had a high saturation of approximately 0.9, consistent with the survey results. Comparison of the results showed that the results of the numerical simulation of solute transport and the test results were nearly identical, and that the numerical simulation results could be used as the basis for groundwater environmental evaluation.

Study on the Principle of Yarn Splicing of Pneumatic Splicer Using Numerical Simulation

2012 ◽  
Vol 588-589 ◽  
pp. 1355-1358
Author(s):  
Xiao Xing ◽  
Guo Ming Ye
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Three Dimensional ◽  
Numerical Results ◽  
Simulation Results

During the splicing process of pneumatic splicer, the principle of yarn splicing is closely related to the flow field inside the splicing chamber. This paper presents a numerical simulation of the flow char-acteristics inside the splicing chamber of the pneumatic splicer. A three-dimensional grid and the realizable tur¬bulence model are used in this simulation. The numerical results of veloc¬ity vectors distribution inside the chamber are shown. Streamlines starting from the two air injectors are also acquired. Based on the simulation, the principle of yarn splicing of the pneumatic splicer is discussed. The airflow in the splicing chamber can be divided into three regions. In addition, the simulation results have well sup¬ported the principle of yarn splicing of pneumatic splicer claimed by the splicing chamber makers.

Numerical Simulation of Seepage Field in Aquifer under the Coal Seam

2014 ◽  
Vol 955-959 ◽  
pp. 3120-3124
Author(s):  
Kai Bian ◽  
Shi Lei Chen ◽  
Xue Yuan Li ◽  
Ying Wang Zhao
Keyword(s):  
Numerical Simulation ◽  
Mathematical Model ◽  
Coal Seam ◽  
Three Dimensional ◽  
Seepage Field ◽  
Limestone Aquifer ◽  
Flow Models ◽  
Hydrogeological Parameters ◽  
Simulation Results ◽  
Technical Basis

In order to figure out seepage field in aquifer under the coal seam, the geology and hydrogeology conditions systematically of study area were analyzed, hydrogeological conceptual model was generalized, mathematical model was built, seepage field of the Taiyuan limestone aquifer was simulated with software Feflow. Simulation results show that hydrogeological parameters of Taiyuan limestone aquifer change greatly in different partitions. The model also indicates the heterogeneity of karst fissure of Taiyuan limestone aquifer. The drainage quantity is from the Ordovician limestone aquifer besides supplying from runoff of upstream and capture excretion of downstream. The research is an attempt to simulate the seepage field in aquifer under coal seam, to some extent, it also provides a technical basis for safe coal mining and as a reference for simulation constructions of three-dimensional groundwater flow models in similar coal mines.

scholarly journals Development of an MTF in ADINA and its application to the study of the Yuxi Basin effect

2021 ◽  
Author(s):  
Tiefei Li ◽  
Xueliang Chen ◽  
Zongchao Li
Keyword(s):  
Numerical Simulation ◽  
Seismic Waves ◽  
Velocity Structure ◽  
Three Dimensional ◽  
Site Effect ◽  
Lumped Mass ◽  
Explicit Finite Element ◽  
Focusing Effect ◽  
Infinite Domains ◽  
Simulation Results

AbstractA three-dimensional multitransmitting formula is developed in ADINA to simulate the input of seismic waves and the scattering of infinite domains at the same time, consistent with the progress of the explicit finite element method of lumped mass. A three-dimensional cube model is built, and a delta pulse wave is input to compare the simulation results with the analytical solutions. The simulation results show that the peak error is 0.2% of the input wave, which meets the requirements of the usual numerical simulation. This method has a certain efficiency advantage in site effect analyses of fine models for localized fields. A velocity structure model of the Yuxi Basin is built, and the associated basin effect is studied by numerical simulation. The distribution of the focusing effect is related to the structure of the narrow east-west and wide north-south features in the Yuxi Basin, and the edge effect is related to the slope of the basin base. A distribution map is given of the amplification effect of ground motion in the basin.

Numerical Simulation and Stereo PIV Test of Inner Flow in a Double Blades Pump

2011 ◽  
Author(s):  
Kai Wang ◽  
Houlin Liu ◽  
Shouqi Yuan ◽  
Minggao Tan ◽  
Yong Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Velocity Field ◽  
Cfd Simulation ◽  
Research Work ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Absolute Velocity ◽  
Operation Condition ◽  
Test Technique ◽  
Simulation Results

A double blades pump is widely used in sewage treatment industry, while at present the research on the internal flow characteristics of the double blades pump is very few. So, the CFD technology and the stereo PIV test technique are applied to study the inner flow in a double blades pump whose specific speed is 110.9. The commercial code FLUENT is used to simulate the inner flow in the double blades pump at 0.6Qd, 0.8Qd, 1.0Qd, 1.2Qd and 1.4Qd. The RNG k-ε turbulence model and SIMPLEC algorithm are used in FLUENT. According to the results of the three-dimensional steady numerical simulation, the distributions of velocity field in the impeller are obtained at the five different operating conditions. The analysis of the numerical simulation results shows that there is an obvious vortex in the impeller passage at off-design conditions. But the number, location and area of the vortex are different from each operation condition. In order to validate CFD simulation results, the stereo PIV is used to test the absolute velocity distribution in the double blades pump at Jiangsu University. The distributions of three-dimensional absolute velocity field at the above five different operating conditions are obtained by the PIV test, and the measured results are compared with the CFD simulation results. The comparison indicates that there are vortexes in impeller passages of the double blades pump under the five operating conditions. But as to the area of the vortex and the relative velocity values of the vortex core, there are some differences between the experiment results and the numerical simulation results. The research work can be applied to instruct the hydraulic design of double blades pumps.

Numerical Simulation Study on the Concentration Field in an Oscillatory Flow Reactor with Conic Ring Baffles

2013 ◽  
Vol 378 ◽  
pp. 418-423
Author(s):  
Gang Liu ◽  
Jia Wu ◽  
Wei Li
Keyword(s):  
Numerical Simulation ◽  
Oscillatory Flow ◽  
Flow Reactor ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Concentration Field ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Turbulent Diffusion Coefficient ◽  
Simulation Results

The three-dimensional construct of concentration field in an oscillatory flow reactor (OFR) containing periodically spaced conic ring baffles was investigated by numerical simulation employing Reynolds-averaged Navier-Stokes equations. The computation covered a range of Oscillatory Reynolds number (Reo) from 623.32 to 3116.58 at Strouhal number (St) 0.995 and 1.99. The contour of concentration field showed that the concentration in the most part of the channel is relative uniform and a small retention area is found below the conic ring baffles, which means a region of relative poor mixing. In addition, the turbulent diffusion coefficient calculated from the simulation results implied the greater oscillatory amplitude and oscillatory frequency superimposed to the fluid, the stronger is the turbulence intensity.

A New Five Dimensional Hyperchaotic System and its Fractional Order Form

2013 ◽  
Vol 464 ◽  
pp. 375-380 ◽  
Author(s):  
Ling Liu ◽  
Chong Xin Liu ◽  
Yi Fan Liao
Keyword(s):  
Numerical Simulation ◽  
Fractional Derivative ◽  
Fractional Order ◽  
Simulation Analysis ◽  
Three Dimensional ◽  
Hyperchaotic System ◽  
Order Form ◽  
Simulation Results ◽  
Predictor Corrector ◽  
New Hyperchaotic System

In this paper, a new five-dimensional hyperchaotic system by introducing two additional states feedback into a three-dimensional smooth chaotic system. With three nonlinearities, this system has more than one positive Lyapunov exponents. Based on the fractional derivative theory, the fractional-order form of this new hyperchaotic system has been investigated. Through predictor-corrector algorithm, the system is proved by numerical simulation analysis. Simulation results are provided to illustrate the performance of the fractional-order hyperchaotic attractors well.

Sign in / Sign up

Export Citation Format

Share Document