scholarly journals Dynamic of Friction Coupling Independently Rotating Wheels for High Speed

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Yan Shi ◽  
Miao Li ◽  
Weihua Ma ◽  
Kang Chen
Keyword(s):  
High Speed ◽  
Rotation Speed ◽  
Friction Pair ◽  
Large Radius ◽  
Coupling Structure ◽  
Lateral Coupling ◽  
Creep Force ◽  
Left And Right ◽  
Curved Track ◽  
Dynamics Models

A new lateral coupling structure with independently rotating wheels (IRW) is proposed, and longitudinal creepage is obtained by replacing the gear pair with the friction pair to synchronize the rotation speed of left and right wheels. The auxiliary wheelset made up of two friction wheels can be placed either under the primary suspension or on the frame. Vehicles dynamics models with three different kinds of bogies are developed, including friction coupling bogie with independently rotating wheels (FCIRW-bogie), bogie with independently rotating wheels (IRW-bogie), and bogie with rigid wheelsets, and their guiding and resetting capability when negotiating large-radius curves are compared and analyzed. Results show that FCIRW has the advantages of both IRW and rigid wheelset. On the straight track, FCIRW has sufficient wheel-rail longitudinal creep force to assist the reset; its critical speed is much higher than that of the rigid wheelset. On the curved track, the whole vehicle wear power of FCIRW-bogie vehicle is about 2/3 of the rigid axle level.

scholarly journals Dynamic Behavior Analysis of the Winding Rotor with Structural Coupling and Time-Frequency Varying Parameters: Simulation and Measurement

2021 ◽  
Vol 11 (17) ◽  
pp. 8124
Author(s):  
Xunxun Ma ◽  
Shujia Li ◽  
Wangliang Tian ◽  
Xiqiang Qu ◽  
Shengze Wang ◽  
...  
Keyword(s):  
Dynamic Behavior ◽  
High Speed ◽  
Critical Speed ◽  
Rotation Speed ◽  
Frequency Dependent ◽  
Measuring Device ◽  
Time Frequency ◽  
Flexible Support ◽  
Coupling Structure ◽  
Speed Up

To satisfy the requirements of high speed, large capacity and constant winding, a textile winding rotor needs to work in a wide rotation speed range and frequently pass through critical speed points. Thus, the winding rotor adopts the flexible long shaft coupling structure and flexible support with rubber O-rings. This kind of rotor has a multi-coupling structure and frequency-dependent parameters characteristics, especially representative and universal in the dynamic analysis method of the high-speed rotor. In this paper, an approach was proposed to investigate the dynamic behavior of the winding rotor considering the flexible coupling and frequency-dependent supporting parameters. Firstly, a dynamic model of the winding rotor was established by using a Timoshenko beam element. Its dynamic behaviors were simulated by considering the time-varying rotation speed and the frequency-dependent parameters of flexible support. Secondly, a non-contact measuring device was developed for measuring the vibration displacement of the winding rotor in three different speed-up times. Finally, based on simulation and measurement data, how flexible support parameters and the speed-up time affect the winding rotor passing through the critical speed point of the rotor smoothly is revealed. The methods and findings reported here can be used for theoretical and experimental vibration analysis of other types of high-speed flexible rotors.

scholarly journals Vibration of Rotating and Revolving Planet Rings with Discrete and Partially Distributed Stiffnesses

2020 ◽  
Vol 11 (1) ◽  
pp. 127
Author(s):  
Fuchun Yang ◽  
Dianrui Wang
Keyword(s):  
High Speed ◽  
Differential Operators ◽  
Natural Frequencies ◽  
Rotation Speed ◽  
Distribution Area ◽  
Vibration Modes ◽  
Governing Equations ◽  
Vibration Properties ◽  
Wide Range ◽  
Forced Responses

Vibration properties of high-speed rotating and revolving planet rings with discrete and partially distributed stiffnesses were studied. The governing equations were obtained by Hamilton’s principle based on a rotating frame on the ring. The governing equations were cast in matrix differential operators and discretized, using Galerkin’s method. The eigenvalue problem was dealt with state space matrix, and the natural frequencies and vibration modes were computed in a wide range of rotation speed. The properties of natural frequencies and vibration modes with rotation speed were studied for free planet rings and planet rings with discrete and partially distributed stiffnesses. The influences of several parameters on the vibration properties of planet rings were also investigated. Finally, the forced responses of planet rings resulted from the excitation of rotating and revolving movement were studied. The results show that the revolving movement not only affects the free vibration of planet rings but results in excitation to the rings. Partially distributed stiffness changes the vibration modes heavily compared to the free planet ring. Each vibration mode comprises several nodal diameter components instead of a single component for a free planet ring. The distribution area and the number of partially distributed stiffnesses mainly affect the high-order frequencies. The forced responses caused by revolving movement are nonlinear and vary with a quasi-period of rotating speed, and the responses in the regions supported by partially distributed stiffnesses are suppressed.

scholarly journals Analysis of the dynamic characteristics of downsized aerostatic thrust bearings with different pressure equalizing grooves at high or ultra-high speed

2021 ◽  
Vol 13 (5) ◽  
pp. 168781402110180
Author(s):  
Ruzhong Yan ◽  
Haojie Zhang
Keyword(s):  
Dynamic Characteristics ◽  
High Speed ◽  
Rotation Speed ◽  
Dynamic Stiffness ◽  
Simulation Method ◽  
Perturbation Amplitude ◽  
Thrust Bearings ◽  
Supply Pressure ◽  
Ultra High Speed ◽  
Air Film

This study adopts the DMT(dynamic mesh technology) and UDF(user defined functions) co-simulation method to study the dynamic characteristics of aerostatic thrust bearings with equalizing grooves and compare with the bearing without equalizing groove under high speed or ultra high speed for the first time. The effects of air film thicness, supply pressure, rotation speed, perturbation amplitude, perturbation frequency, and cross section of the groove on performance characteristics of aerostatic thrust bearing are thoroughly investigated. The results show that the dynamic stiffiness and damping coefficient of the bearing with triangular or trapezoidal groove have obvious advantages by comparing with that of the bearing without groove or with rectangular groove for the most range of air film thickness, supply pressure, rotation speed, perturbation amplitude, especially in the case of high frequency, which may be due to the superposition of secondary throttling effect and air compressible effect. While the growth range of dynamic stiffness decreases in the case of high or ultra-high rotation speed, which may be because the Bernoulli effect started to appear. The perturbation amplitude only has little influence on the dynamic characteristic when it is small, but with the increase of perturbation amplitude, the influence becomes more obvious and complex, especially for downsized aerostatic bearing.

On the Planning and Construction of Railway Curved Track

2021 ◽  
Vol 13 (2) ◽  
Author(s):  
Sono Bhardawaj ◽  
Rakesh Chandmal Sharma ◽  
Sunil Kumar Sharma ◽  
Neeraj Sharma
Keyword(s):  
High Speed ◽  
Time Derivative ◽  
Railway Track ◽  
Lateral Acceleration ◽  
Transition Curve ◽  
Railway Vehicle ◽  
Geometric Conditions ◽  
Curve Track ◽  
Curved Track ◽  
Transition Curves

Increasing demand for railway vehicle speed has pushed the railway track designers to develop high-quality track. An important measure of track quality is the character of the transition curve track connecting different intersecting straight tracks. A good transition curve track must be able to negotiate the intermittent stresses and dynamic effects caused by changes in lateral acceleration at high speed. This paper presents the constructional methods for planning transition curves considering the dynamics of movement. These methods consider the non-compensated lateral acceleration, deviation in lateral acceleration and its higher time derivatives. This paper discusses the laying methods of circular, vertical and transition curves. Key aspects in laying a curved track e.g. widening of gauge on curves are discussed in this paper. This paper also suggests a transition curve which is effective not only from a dynamic point of view considering lateral acceleration and its higher time derivative but also consider the geometric conditions along with the required deflection angle.

Vertical Optical Coupling Structure Based on Polymer for Small Size and High-Speed Photodetectors

2018 ◽  
Vol 30 (21) ◽  
pp. 1886-1889 ◽  
Author(s):  
Carlos Viana ◽  
Zerihun Gedeb Tegegne ◽  
Jacopo Nanni ◽  
Giovanni Tartarini ◽  
Catherine Algani ◽  
...  
Keyword(s):  
High Speed ◽  
Optical Coupling ◽  
Coupling Structure

Inverse Dynamic Analysis and Linearisation of a High Speed Parallel Mechanism

2005 ◽  
Author(s):  
M. Necip Sahinkaya ◽  
Yanzhi Li
Keyword(s):  
Dynamic Analysis ◽  
Parallel Mechanism ◽  
High Speed ◽  
Inverse Dynamics ◽  
Motion Path ◽  
Model Parameters ◽  
Control Input ◽  
Inverse Dynamic ◽  
Inverse Dynamic Analysis ◽  
Dynamics Models

Inverse dynamic analysis of a three degree of freedom parallel mechanism driven by three electrical motors is carried out to study the effect of motion speed on the system dynamics and control input requirements. Availability of inverse dynamics models offer many advantages, but controllers based on real-time inverse dynamic simulations are not practical for many applications due to computational limitations. An off-line linearisation of system and error dynamics based on the inverse dynamic analysis is developed. It is shown that accurate linear models can be obtained even at high motion speeds eliminating the need to use computationally intensive inverse dynamics models. A point-to-point motion path for the mechanism platform is formulated by using a third order exponential function. It is shown that the linearised model parameters vary significantly at high motion speeds, hence it is necessary to use adaptive controllers for high performance.

scholarly journals Blade Tip-timing Technology with Multiple Reference Phases for Online Monitoring of High-speed Blades under Variable-speed Operation

2018 ◽  
Vol 18 (6) ◽  
pp. 243-250 ◽  
Author(s):  
Zhang Ji-wang ◽  
Zhang Lai-bin ◽  
Ding Ke-Qin ◽  
Duan Li-xiang
Keyword(s):  
High Speed ◽  
Online Monitoring ◽  
Rotation Speed ◽  
Experimental Tests ◽  
Reference Points ◽  
Variable Speed ◽  
Rotating Shaft ◽  
Virtual Reference ◽  
Blade Tip ◽  
Multiple Reference

Abstract High-speed blades form core mechanical components in turbomachines. Research concerning online monitoring of operating states of such blades has drawn increased attention in recent years. To this end, various methods have been devised, of which, the blade tip-timing (BTT) technique is considered the most promising. However, the traditional BTT method is only suitable for constant-speed operations. But in practice, the rotational speed of turbomachine blades is constantly changing under the influence of external factors, which lead to unacceptable errors in measurement. To tackle this problem, a new BTT method based on multi-phases is proposed. A plurality of phases was arranged as evenly as possible on the rotating shaft to determine the rotation speed. Meanwhile, the corresponding virtual reference point was determined in accordance with the number of blades between consecutive phases. Based on these reference points, equations to measure displacement due to blade vibrations were deduced. Finally, mathematical modeling, numerical simulation and experimental tests were performed to verify the validity of the proposed method. Results demonstrate that the error in measurement induced when using the proposed method is less than 1.8 %, which is much lower compared to traditional methods utilized under variable-speed operation.

EXPERIMENTAL AND NUMERICAL STUDY OF THERMAL ANALYSIS OF HIGH-SPEED FRICTION BRAKING SYSTEM

2011 ◽  
Vol 10 (01) ◽  
pp. 135-142
Author(s):  
CHUNMEI ZHANG ◽  
YONGFENG LI
Keyword(s):  
Thermal Analysis ◽  
Friction Surface ◽  
High Speed ◽  
Material Selection ◽  
Numerical Study ◽  
Friction Pair ◽  
Maximum Temperature ◽  
Dimensionless Time ◽  
Braking System ◽  
Friction Braking System

Thermal analysis can be used as one of the basis for the friction pair material selection in high-speed friction braking system. In this study, the experimental results showed that surface temperature could be reduced by increasing the radius of the friction disk or thermal conductivity coefficient of disk material with stable braking; In the early stage of long braking, the temperature on the friction surface rises rapidly, but further braking does not lead to a significant rise in temperature; In the case of short braking, there is not enough time for the friction surface to reach the critical temperature, and the disk surface reaches the maximum temperature at the end of braking. During long braking, the dimensionless time capacity of the friction surface reaching the highest temperature is F0 ≈ 0.1F0s.

Analysis on Vehicle-Bridge Coupled Vibration of a Rigid-Frame Arch Bridge Based on Measured Road Roughness

2011 ◽  
Vol 255-260 ◽  
pp. 1775-1780
Author(s):  
Wan Shui Han ◽  
Su Jing Yuan ◽  
Bing Wang
Keyword(s):  
High Speed ◽  
Contact Forces ◽  
Dynamic Responses ◽  
Coupled Vibration ◽  
Arch Bridge ◽  
Rigid Frame ◽  
Road Roughness ◽  
Left And Right ◽  
Spectrum Characteristics ◽  
Bridge System

Firstly, synchronous field measurements were carried out for the road roughness of the left and right wheels to obtain the roughness profile using a high speed laser roadway testing vehicle. Secondly, programming idea of multi-girder vehicle-bridge coupled vibration analysis module was presented briefly. Finally, a three-axle heavy truck crossing a rigid-frame arch bridge was taken as an example, detailed comparing and analyzing was carried out for the influence on the dynamic responses and spectrum characteristics of the vehicle-bridge system from three excitation cases which include using measured road roughness corresponding respectively to left and right wheels, using measured road roughness of left wheels and right wheels simultaneously. The analysis shows that when the differences in road roughness between left and right wheels are significant, the responses computed with inconsistent excitation is smaller than that with both of the latter two excitation cases, and there are some differences between the vertical contact forces of wheels and the spectrum characteristics of the vehicle-bridge system.

Sign in / Sign up

Export Citation Format

Share Document