scholarly journals Decentralized Optimization Algorithms for Variable Speed Pumps Operation Based on Local Interaction Game

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
Shi-Qiang Wang ◽  
Jian-Chun Xing ◽  
Zi-Yan Jiang ◽  
Yun-Chuang Dai
Keyword(s):  
Optimization Method ◽  
Local Interaction ◽  
Total Power ◽  
Variable Speed ◽  
Optimal Control Strategy ◽  
Decentralized Estimation ◽  
Decentralized Optimization ◽  
Total Power Consumption ◽  
Estimation Of Distribution ◽  
Smart Pump

A fully distributed optimal control strategy for the parallel variable speed pumps in heating, ventilation, and air-conditioning (HVAC) systems is proposed. Compared with the traditional centralized method, the efficient control and coordination are scattered to every updated smart pump without the need for a monitoring host. Similar to the structure, mechanism, and characteristics of biological communities, a smart pump can communicate with adjacent nodes and operate collaboratively to complete pumps group operation with the least total power consumption under load demand and system constraints. And a decentralized optimization method that is decentralized estimation of distribution algorithm (DEDA) under local interaction games framework has been transplanted to the proposed structure to optimize the pumps working in parallel mode. Besides, convergence property of the two novel mechanisms is analyzed theoretically. Finally, simulation studies have been conducted based on the models of a physical pumps system, and the performance of the proposed algorithm is compared with centralized algorithms in terms of both effectiveness and stability. The results provide support for the validity of the proposed algorithms and control structure.

scholarly journals Joint Optimization of Pico-Base-Station Density and Transmit Power for an Energy-Efficient Heterogeneous Cellular Network

2019 ◽  
Vol 11 (10) ◽  
pp. 208
Author(s):  
Jie Yang ◽  
Ziyu Pan ◽  
Hengfei Xu ◽  
Han Hu
Keyword(s):  
Energy Efficiency ◽  
Focal Point ◽  
Transmission Rate ◽  
Optimization Method ◽  
Base Station ◽  
Base Stations ◽  
Joint Optimization ◽  
Total Power ◽  
Transmit Power ◽  
Total Power Consumption

Heterogeneous cellular networks (HCNs) have emerged as the primary solution for explosive data traffic. However, an increase in the number of base stations (BSs) inevitably leads to an increase in energy consumption. Energy efficiency (EE) has become a focal point in HCNs. In this paper, we apply tools from stochastic geometry to investigate and optimize the energy efficiency (EE) for a two-tier HCN. The average achievable transmission rate and the total power consumption of all the BSs in a two-tier HCN is derived, and then the EE is formulated. In order to maximize EE, a one-dimensional optimization algorithm is used to optimize picocell BS density and transmit power. Based on this, an alternating optimization method aimed at maximizing EE is proposed to jointly optimize transmit power and density of picocell BSs. Simulation results validate the accuracy of the theoretical analysis and demonstrate that the proposed joint optimization method can obviously improve EE.

scholarly journals An Economical and Precise Cooling Model and Its Application in a Single-Cylinder Diesel Engine

2021 ◽  
Vol 11 (15) ◽  
pp. 6749
Author(s):  
Zhifeng Xie ◽  
Ao Wang ◽  
Zhuoran Liu
Keyword(s):  
Diesel Engine ◽  
Cooling System ◽  
Combustion Engine ◽  
Electronic Control Unit ◽  
Total Power ◽  
Dynamical Characteristic ◽  
Water Jacket ◽  
Single Cylinder ◽  
Pump Speed ◽  
Total Power Consumption

The cooling system is an important subsystem of an internal combustion engine, which plays a vital role in the engine’s dynamical characteristic, the fuel economy, and emission output performance at each speed and load. This paper proposes an economical and precise model for an electric cooling system, including the modeling of engine heat rejection, water jacket temperature, and other parts of the cooling system. This model ensures that the engine operates precisely at the designated temperature and the total power consumption of the cooling system takes the minimum value at some power proportion of fan and pump. Speed maps for the cooling fan and pump at different speeds and loads of engine are predicted, which can be stored in the electronic control unit (ECU). This model was validated on a single-cylinder diesel engine, called the DK32. Furthermore, it was used to tune the temperature of the water jacket precisely. The results show that in the common use case, the electric cooling system can save the power of 255 W in contrast with the mechanical cooling system, which is about 1.9% of the engine’s power output. In addition, the validation results of the DK32 engine meet the non-road mobile machinery China-IV emission standards.

scholarly journals On-CMOS Image Sensor Processing for Lane Detection

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3713
Author(s):  
Soyeon Lee ◽  
Bohyeok Jeong ◽  
Keunyeol Park ◽  
Minkyu Song ◽  
Soo Youn Kim
Keyword(s):  
Edge Detection ◽  
High Speed ◽  
Cmos Image Sensor ◽  
Image Sensor ◽  
Image Resolution ◽  
Lane Detection ◽  
Frame Rate ◽  
Total Power ◽  
Detection Accuracy ◽  
Total Power Consumption

This paper presents a CMOS image sensor (CIS) with built-in lane detection computing circuits for automotive applications. We propose on-CIS processing with an edge detection mask used in the readout circuit of the conventional CIS structure for high-speed lane detection. Furthermore, the edge detection mask can detect the edges of slanting lanes to improve accuracy. A prototype of the proposed CIS was fabricated using a 110 nm CIS process. It has an image resolution of 160 (H) × 120 (V) and a frame rate of 113, and it occupies an area of 5900 μm × 5240 μm. A comparison of its lane detection accuracy with that of existing edge detection algorithms shows that it achieves an acceptable accuracy. Moreover, the total power consumption of the proposed CIS is 9.7 mW at pixel, analog, and digital supply voltages of 3.3, 3.3, and 1.5 V, respectively.

scholarly journals Efficient Operation Method of Aquifer Thermal Energy Storage System Using Demand Response

Energies ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3129
Author(s):  
Jewon Oh ◽  
Daisuke Sumiyoshi ◽  
Masatoshi Nishioka ◽  
Hyunbae Kim
Keyword(s):  
Energy Storage ◽  
Power Consumption ◽  
Thermal Energy ◽  
Demand Response ◽  
Thermal Energy Storage ◽  
Heat Storage ◽  
Storage System ◽  
Total Power ◽  
Operation Method ◽  
Total Power Consumption

The mass introduction of renewable energy is essential to reduce carbon dioxide emissions. We examined an operation method that combines the surplus energy of photovoltaic power generation using demand response (DR), which recognizes the balance between power supply and demand, with an aquifer heat storage system. In the case that predicts the occurrence of DR and performs DR storage and heat dissipation operation, the result was an operation that can suppress daytime power consumption without increasing total power consumption. Case 1-2, which performs nighttime heat storage operation for about 6 h, has become an operation that suppresses daytime power consumption by more than 60%. Furthermore, the increase in total power consumption was suppressed by combining DR heat storage operation. The long night heat storage operation did not use up the heat storage amount. Therefore, it is recommended to the heat storage operation at night as much as possible before DR occurs. In the target area of this study, the underground temperature was 19.1 °C, the room temperature during cooling was about 25 °C and groundwater could be used as the heat source. The aquifer thermal energy storage (ATES) system in this study uses three wells, and consists of a well that pumps groundwater, a heat storage well that stores heat and a well that used heat and then returns it. Care must be taken using such an operation method depending on the layer configuration.

scholarly journals Decentralized Optimization for a Novel Control Structure of HVAC System

2016 ◽  
Vol 2016 ◽  
pp. 1-13 ◽  
Author(s):  
Shiqiang Wang ◽  
Jianchun Xing ◽  
Ziyan Jiang ◽  
Juelong Li
Keyword(s):  
Control System ◽  
Decentralized Control ◽  
Control Structure ◽  
Optimization Method ◽  
Labor Cost ◽  
Smart Device ◽  
Hvac System ◽  
Decentralized Optimization ◽  
System A ◽  
Novel Method

A decentralized control structure is introduced into the heating, ventilation, and air conditioning (HVAC) system to solve the high maintenance and labor cost problem in actual engineering. Based on this new control system, a decentralized optimization method is presented for sensor fault repair and optimal group control of HVAC equipment. Convergence property of the novel method is theoretically analyzed considering both convex and nonconvex systems with constraints. In this decentralized control system, traditional device is fitted with a control chip such that it becomes a smart device. The smart device can communicate and operate collaboratively with the other devices to accomplish some designated tasks. The effectiveness of the presented method is verified by simulations and hardware tests.

Design and Layout of a High-Performance PWM Control Class D Amplifiers IC Systems

2012 ◽  
Vol 203 ◽  
pp. 469-473
Author(s):  
Ruei Chang Chen ◽  
Shih Fong Lee
Keyword(s):  
Low Power ◽  
High Performance ◽  
Low Voltage ◽  
Design Flow ◽  
Total Power ◽  
Cmos Process ◽  
Low Power Circuits ◽  
Class D ◽  
Total Power Consumption ◽  
Power Circuits

This paper presents the design and implementation of a novel pulse width modulation control class D amplifiers chip. With high-performance, low-voltage, low-power and small area, these circuits are employed in portable electronic systems, such as the low-power circuits, wireless communication and high-frequency circuit systems. This class D chip followed the chip implementation center advanced design flow, and then was fabricated using Taiwan Semiconductor Manufacture Company 0.35-μm 2P4M mixed-signal CMOS process. The chip supply voltage is 3.3 V which can operate at a maximum frequency of 100 MHz. The total power consumption is 2.8307 mW, and the chip area size is 1.1497×1.1497 mm2. Finally, the class D chip was tested and the experimental results are discussed. From the excellent performance of the chip verified that it can be applied to audio amplifiers, low-power circuits, etc.

Low-Carbon Clean Technology for Waste Energy Recovery in Power Plants Based on Green Environmental Protection

2021 ◽  
Author(s):  
Yong Tian ◽  
Wen-Jing Liu ◽  
Qi-jie Jiang ◽  
Xin-Ying Xu
Keyword(s):  
Power Generation ◽  
Power Plants ◽  
Biomass Energy ◽  
Energy Utilization ◽  
Pollutant Emissions ◽  
Total Power ◽  
Economic Losses ◽  
Biomass Waste ◽  
Emission Analysis ◽  
Total Power Consumption

With the development of biomass power generation technology, biomass waste has a more excellent recycling value. The article establishes a biomass waste inventory model based on the material flow analysis method and predicts raw material waste’s energy utilization potential. The results show that the amount of biomass waste generated from 2016 to 2020 is on the rise. In 2020, biomass waste’s energy utilization can reach 107,802,300 tons, equivalent to 1,955.28PJ of energy. Through biomass energy analysis and emission analysis, the results show that the biomass waste can generate 182.02 billion kW⋅h in 2020, which can replace 35.9% of the region’s total power consumption, which is compared with the traditional power generation method under the same power generation capacity. Power generation can reduce SO2 emissions by 250,400 tons, NOx emissions by 399,300 tons, and PM10 emissions by 49,700 tons. Reduce direct economic losses by 712 million yuan. Therefore, Chinese promotion of the recycling of biomass waste and the acceleration of the biomass energy industry’s development is of great significance for reducing pollutant emissions and alleviating energy pressure.

scholarly journals A Novel Differential Log-Companding Amplifier for Biosignal Sensing

2016 ◽  
Vol 2016 ◽  
pp. 1-7
Author(s):  
Zigang Dong ◽  
Xiaolin Zhou ◽  
Yuanting Zhang
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
Nonlinear Function ◽  
New Method ◽  
Total Power ◽  
Maximum Output ◽  
Output Current ◽  
Current Range ◽  
Symmetrical Configuration ◽  
Total Power Consumption

We proposed a new method for designing the CMOS differential log-companding amplifier which achieves significant improvements in linearity, common-mode rejection ratio (CMRR), and output range. With the new nonlinear function used in the log-companding technology, this proposed amplifier has a very small total harmonic distortion (THD) and simultaneously a wide output current range. Furthermore, a differential structure with conventionally symmetrical configuration has been adopted in this novel method in order to obtain a high CMRR. Because all transistors in this amplifier operate in the weak inversion, the supply voltage and the total power consumption are significantly reduced. The novel log-companding amplifier was designed using a 0.18 μm CMOS technology. Improvements in THD, output current range, noise, and CMRR are verified using simulation data. The proposed amplifier operates from a 0.8 V supply voltage, shows a 6.3 μA maximum output current range, and has a 6 μW power consumption. The THD is less than 0.03%, the CMRR of this circuit is 74 dB, and the input referred current noise density is166.1 fA/Hz. This new method is suitable for biomedical applications such as electrocardiogram (ECG) signal acquisition.

Exergy Analysis of a Novel Cryogenic Concept for the Liquefaction of Natural Gas Integrated Into an Air Separation Process

2016 ◽  
Author(s):  
S. Tesch ◽  
T. Morosuk ◽  
G. Tsatsaronis
Keyword(s):  
Natural Gas ◽  
Power Consumption ◽  
Exergy Analysis ◽  
Primary Energy ◽  
Separation Process ◽  
Air Separation ◽  
Total Power ◽  
Separation Unit ◽  
Total Power Consumption ◽  
Liquefaction Temperature

The increasing demand for primary energy leads to a growing market of natural gas and the associated market for liquefied natural gas (LNG) increases, too. The liquefaction of natural gas is an energy- and cost-intensive process. After exploration, natural gas, is pretreated and cooled to the liquefaction temperature of around −160°C. In this paper, a novel concept for the integration of the liquefaction of natural gas into an air separation process is introduced. The system is evaluated from the energetic and exergetic points of view. Additionally, an advanced exergy analysis is conducted. The analysis of the concepts shows the effect of important parameters regarding the maximum amount of liquefiable of natural gas and the total power consumption. Comparing the different cases, the amount of LNG production could be increased by two thirds, while the power consumption is doubled. The results of the exergy analysis show, that the introduction of the liquefaction of natural gas has a positive effect on the exergetic efficiency of a convetional air separation unit, which increases from 38% to 49%.

Sign in / Sign up

Export Citation Format

Share Document