scholarly journals Tartrazine Removal from Aqueous Solution by HDTMA-Br-Modified Colombian Bentonite

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Ronald A. Otavo-Loaiza ◽  
Nancy R. Sanabria-González ◽  
Gloria I. Giraldo-Gómez
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Industrial Wastewater ◽  
Maximum Adsorption Capacity ◽  
Sunset Yellow ◽  
Anionic Dyes ◽  
Ph Values ◽  
Nacl Concentration ◽  
Langmuir And Freundlich Models ◽  
Maximum Removal

The effect of pH, ionic strength (NaCl added), agitation speed, adsorbent mass, and contact time on the removal of tartrazine from an aqueous solution, using an organobentonite, has been studied. A complete factorial design 32 with two replicates was used to evaluate the influence of the dye concentration (30, 40, and 50 mg/L) and amount of adsorbent (25, 35, and 45 mg) on decolorization of the solution. Experimental data were evaluated with Design Expert® software using a response surface methodology (RSM) in order to obtain the interaction between the processed variables and the response. pH values between 2 and 9, stirring speed above 200 rpm, and contact time of 60 min did not have a significant effect on decolorization. The optimum conditions for maximum removal of tartrazine from an aqueous solution of 30 mg/L were follows: pH = 6.0, NaCl concentration = 0.1 M, stirring speed = 230 rpm, temperature = 20°C, contact time = 60 min, and the organobentonite amount = 38.04 mg. The equilibrium isotherm at 20°C was analyzed by means of the Langmuir and Freundlich models, and the maximum adsorption capacity obtained was 40.79 ± 0.71 mg/g. This adsorption process was applied in a sample of industrial wastewater containing tartrazine and sunset yellow, having obtained a decolorization rate higher than 98% for both dyes. These results suggest that organobentonite is an effective adsorbent for the removal of anionic dyes from an aqueous solution.

Adsorption of anionic dyes in aqueous solution using chemically modified barley straw

2010 ◽  
Vol 62 (5) ◽  
pp. 1177-1182 ◽  
Author(s):  
Shariff Ibrahim ◽  
Is Fatimah ◽  
Ha-Ming Ang ◽  
Shaobin Wang
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Agricultural Waste ◽  
Barley Straw ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Anionic Dyes ◽  
Isotherm Study ◽  
Chemically Modified ◽  
The Stability

An agricultural waste derived adsorbent was prepared by chemically modified barley straw with NaOH and a cationic surfactant hexadecylpyridinium chloride monohydrate (CPC). The prepared adsorbent, BMBS, was used for removal of anionic dyes; Acid Blue (AB40) and Reactive Blue 4 (RB4) from aqueous solution in a batch adsorption system. The adsorbent was characterized by FT-IR and elemental composition. The stability of CPC adsorbed on straw surface was also evaluated by exposing to aqueous solution. In adsorption tests, influence of operation parameters such as contact time, initial concentration and pH of solution on AB40 and RB4 uptake were investigated and discussed. The CPC was observed strongly attached to straw surface and removal percentage of AB40 and RB4 was increased with increasing in contact time. The adsorption of dyes on modified straw surface was favorable at high acidic condition and desorption was found relatively low upon exposing to the desorption agent (i.e water). Dynamic experiment revealed that the kinetic data fitted well to the pseudo-second-order model for both of the dyes. The isotherm study also indicated that RB4 and AB40 adsorption suited well with the Langmuir model, The maximum adsorption capacity determined from the Langmuir isotherm at 25°C was 51.95 mg g−1 and 31.5 for AB40 and RB4, respectively.

scholarly journals Modified/Unmodified Nanoparticle Adsorbents of Cellulose Origin With High Adsorptive Potential for Removal of Pb(II) From Aqueous Solution

2017 ◽  
Vol 13 (27) ◽  
pp. 425
Author(s):  
Azeh Yakubu ◽  
Gabriel Ademola Olatunji ◽  
Folahan Amoo Adekola
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Adsorption Process ◽  
Correlation Coefficients ◽  
Solution Temperature ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity ◽  
Kinetics Of Adsorption ◽  
Kinetics Of

This investigation was conducted to evaluate the adsorption capacity of nanoparticles of cellulose origin. Nanoparticles were synthesized by acid hydrolysis of microcrystalline cellulose/cellulose acetate using 64% H3PO4 and characterized using FTIR, XRD, TGA-DTGA, BET and SEM analysis. Adsorption kinetics of Pb (II) ions in aqueous solution was investigated and the effect of initial concentration, pH, time, adsorbent dosage and solution temperature. The results showed that adsorption increased with increasing concentration with removal efficiencies of 60% and 92.99% for Azeh2 and Azeh10 respectively for initial lead concentration of 3 mg/g. The effects of contact time showed that adsorption maximum was attained within 24h of contact time. The maximum adsorption capacity and removal efficiency were achieved at pH6. Small dose of adsorbent had better performance. The kinetics of adsorption was best described by the pseudo-second-Order model while the adsorption mechanism was chemisorption and pore diffusion based on intra-particle diffusion model. The isotherm model was Freundlich. Though, all tested isotherm models relatively showed good correlation coefficients ranging from 0.969-1.000. The adsorption process was exothermic for Azeh-TDI, with a negative value of -12.812 X 103 KJ/mol. This indicates that the adsorption process for Pb by Azeh-TDI was spontaneous. Adsorption by Azeh2 was endothermic in nature.

scholarly journals Biosorption of Lead Ions from Aqueous Solution UsingFicus benghalensisL.

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Venkateswara Rao Surisetty ◽  
Janusz Kozinski ◽  
L. Rao Nageswara
Keyword(s):  
Aqueous Solution ◽  
Process Parameters ◽  
Contact Time ◽  
Batch Process ◽  
Ion Concentration ◽  
Lead Ions ◽  
Lead Ion ◽  
Maximum Adsorption Capacity ◽  
Ficus Benghalensis ◽  
Leaf Powder

Ficus benghalensisL., a plant-based material leaf powder, is used as an adsorbent for the removal of lead ions from aqueous solution using the biosorption technique. The effects of process parameters such as contact time, adsorbent size and dosage, initial lead ion concentration, and pH of the aqueous solution on bio-sorption of lead byFicus benghalensisL. were studied using batch process. The Langmuir isotherm was more suitable for biosorption followed by Freundlich and Temkin isotherms with a maximum adsorption capacity of 28.63 mg/g of lead ion on the biomass ofFicus benghalensisL. leaves.

scholarly journals Phenol removal from aqueous solution using silica and activated carbon derived from rice husk

2019 ◽  
Vol 14 (4) ◽  
pp. 897-907 ◽  
Author(s):  
Hosseinali Asgharnia ◽  
Hamidreza Nasehinia ◽  
Roohollah Rostami ◽  
Marziah Rahmani ◽  
Seyed Mahmoud Mehdinia
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Water Treatment ◽  
Organic Pollutants ◽  
Rice Husk ◽  
Contact Time ◽  
Adsorption Process ◽  
Phenol Removal ◽  
Initial Concentration ◽  
Maximum Removal

Abstract Phenol and its derivatives are organic pollutants with dangerous effects, such as poisoning, carcinogenicity, mutagenicity, and teratogenicity in humans and other organisms. In this study, the removal of phenol from aqueous solution by adsorption on silica and activated carbon of rice husk was investigated. In this regard, the effects of initial concentration of phenol, pH, dosage of the adsorbents, and contact time on the adsorption of phenol were investigated. The results showed that the maximum removal of phenol by rice husk silica (RHS) and rice husk activated carbon (RHAC) in the initial concentration of 1 mgL−1 phenol, 2 gL−1 adsorbent mass, 120 min contact time, and pH 5 (RHS) or pH 6 (RHAC) were obtained up to 91% and 97.88%, respectively. A significant correlation was also detected between increasing contact times and phenol removal for both adsorbents (p < 0.01). The adsorption process for both of the adsorbents was also more compatible with the Langmuir isotherm. The results of this study showed that RHS and RHAC can be considered as natural and inexpensive adsorbents for water treatment.

scholarly journals Fast and Effective Route for Removing Methylene Blue from Aqueous Solution by Using Red Mud-Activated Graphite Composites

2019 ◽  
Vol 2019 ◽  
pp. 1-7
Author(s):  
Ha Xuan Linh ◽  
Ngo Thi Thu ◽  
Tran Quoc Toan ◽  
Do Tra Huong ◽  
Bui Thanh Giang ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Red Mud ◽  
Contact Time ◽  
Electrochemical Activation ◽  
Maximum Adsorption Capacity ◽  
Graphite Composite ◽  
Isotherm Equation ◽  
Langmuir Isotherm Equation ◽  
Graphite Composites

In this work, the mixture of red mud slurry and inorganic salt ((NH4)2SO4) has been used as an electrolyte for electrochemical activation of graphite. The red mud-activated graphite composite was then used as an adsorbent for removing methylene blue from aqueous solution by the batch method. The effect of pH, contact time, adsorbent dosage, and the initial concentration of methylene blue was investigated. The optimal condition was found at pH 6, contact time 120 min, and amount of adsorbent 1 mg/L. The maximum adsorption capacity was found to be 89.28 mg/g based on the Langmuir isotherm equation, suggesting that the red mud-activated graphite composite is a very potential adsorbent for removing methylene blue and is also used in other coloured wastewater treatments.

Sorption of Copper and Zinc from Aqueous Solutions by Microwave Incinerated Sugarcane Bagasse Ash (MISCBA)

2016 ◽  
Vol 835 ◽  
pp. 378-385 ◽  
Author(s):  
Ibrahim Umar Salihi ◽  
Shamsul Rahman Mohamed Kutty ◽  
Mohamed Hasnain Isa ◽  
Usman Aminu Umar ◽  
Emmanuel Olisa
Keyword(s):  
Heavy Metals ◽  
Aqueous Solution ◽  
Correlation Coefficient ◽  
Sugarcane Bagasse ◽  
Contact Time ◽  
Industrial Wastewater ◽  
Low Cost ◽  
Isotherm Model ◽  
Copper And Zinc ◽  
Sugarcane Bagasse Ash

Industrial wastewater containing toxic pollutants such as heavy metals tends to contaminate the environment once it is release without proper treatment. Heavy metals are toxic to both human and other living organisms. It is necessary to treat industrial wastewater polluted with heavy metals prior to its discharge into the receiving environment. In this study, low cost adsorbent was generated from sugarcane bagasse through incineration. The prepared adsorbent “microwave incinerated sugarcane bagasse ash” (MISCBA) was used in removing copper and zinc from aqueous solution. Parameters of importance such as pH, contact time and adsorbent dosages are studied to investigate their effects on the adsorption of copper and zinc. Maximum adsorption was observed at pH 6.0, contact time of 180 minutes and adsorbent dosage of 10 g/L. Zinc removal follows Langmuir isotherm model with correlation coefficient of 0.9291. Copper adsorption follows both Langmuir and Freundlich isotherm model with correlation coefficient of 0.9181 and 0.9742, respectively. Removal capacities of 38.4 mg/g and 20.4 mg/g were obtained for copper and zinc, respectively. Application of MISCBA as low - cost adsorbent have shown significant outcome in removal of copper and zinc from aqueous solution.

scholarly journals Benzene Sulfonate Modified ZnCr-LDH and Its Enhanced Adsorption Properties for Anionic Dyes

2021 ◽  
Author(s):  
Jia Lin ◽  
Yude Zhang ◽  
Qian Zhang ◽  
Jinli Shang ◽  
Fuyao Deng
Keyword(s):  
Aqueous Solution ◽  
Active Sites ◽  
Adsorption Process ◽  
Adsorption Behavior ◽  
Maximum Adsorption Capacity ◽  
Benzene Sulfonate ◽  
Dye Molecules ◽  
Anionic Dyes ◽  
One Pot ◽  
High Efficient

Abstract A benzene sulfonate modified hydrotalcite (SO3-LDH) was synthesized by a facile one-pot hydrothermal technique, which can efficiently remove methyl orange (MO), Congo red (CR) and orange II (OII) from aqueous solution. After modified by benzene sulfonate, the microstructure of hydrotalcite changes obviously, from the cellular structure to the stacking structure formed by the face-face contact of hydrotalcite nanosheets, which resulted in much more exchangeable nitrate ions to remain in the interlayer space. The pre-insertion of benzene sulfonate as a pillar expanded the interlayer gallery, which facilitated the pollutant anions (MO, CR and OII) into the interlayer of LDH in the subsequent adsorption process. The maximum adsorption capacity of SO3-LDH for MO, CR and OII was 4200.8 mg/g, 1252.0 mg/g and 1670.6 mg/g respectively, which is approximately 1.86 times, 1.8 times and 2.32 times that of the pristine NO3-LDH, respectively. The removal mechanism of anionic dyes was determined as anion exchange between NO3− ions and dye molecules. The adsorption behavior for MO and OII is multilayer adsorption, while the adsorption behavior for CR is monolayer adsorption. The adsorption process mainly was controlled by the chemical bonding between the dye molecules and adsorbent active sites. The benzene sulfonate modified LDH has a great potential to be used as a high-efficient adsorbent to remove anionic dyes from aqueous solution.

scholarly journals Adsorption Of Cd(II) Ions From Aqueous Solution By A Low-Cost Biosorbent Prepared From Ipomea Pes-Caprae Stem

2020 ◽  
Vol 9 (3) ◽  
pp. 197-206
Author(s):  
Thaharah Ramadhani ◽  
Faisal Abdullah ◽  
Indra Indra ◽  
Abrar Muslim ◽  
Suhendrayatna Suhendrayatna ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Optimal Condition ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Low Cost ◽  
Ph Values ◽  
Monolayer Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Ft Ir

The use of a low-cost biosorbent prepared from Ipomoea pes-caprae stem for the adsorption of Cd(II) ions from aqueous solution at different contact times, biosorbent sizes, pH values, and initial Cd(II) ions concentration solution was investigated. The biosorbent was analyzed using Fourier-transform infrared spectroscopy (FT-IR) to find important IR-active functional groups. A scanning electron microscope (SEM) was used to examine the biosorbent morphology. The experimental results showed the highest Cd(II) ions adsorption was 29.513 mg/g  under an optimal condition as initial Cd(II) ions concentration of 662.77 mg/L, 1 g dose, 80-min contact time, pH 5, 75 rpm of stirring speed, 1 atm, and 30 oC. Cd(II) ions' adsorption kinetics obeys the linearized pseudo-second-order kinetics (R2 = 0.996), and the adsorption capacity is based on the optimal condition, and the rate attained was 44.444 mg/g and 0.097 g/mg. Min, respectively. Besides, the adsorption isotherms were very well fitted by the linearized Langmuir isotherm model, and the monolayer adsorption capacity and pore volume determined was 30.121 mg/g and 0.129 L/mg, respectively. These results indicated the chemisorption nature

scholarly journals Adsorptive Removal of Congo red dye from wastewater using Fenugreek Powder

2020 ◽  
Author(s):  
Neha bhadauria ◽  
Arjun Suresh
Keyword(s):  
Aqueous Solution ◽  
Congo Red ◽  
Contact Time ◽  
Adsorption Process ◽  
Dye Adsorption ◽  
Textile Dye ◽  
Adsorptive Removal ◽  
Congo Red Dye ◽  
Red Dye ◽  
Maximum Removal

The present study analyzed the efficiency of a naturally derived fenugreek powder for removal of Congo red dye from the aqueous solution. The flocculation Studies on Congo Red (CR) a hazardous, textile dye onto Fenugreek Powder and its adsorption was analyzed. Fenugreek Powder is Eco-friendly, biodegradable and locally available in the market. The dye adsorption process was performed in different batches at varying pH, dye concentration, adsorbent concentration and contact time to get the best results. The result showed that the maximum removal of dye was 42.4% with 10mg/l of Fenugreek powder at pH 4.

scholarly journals Adsorptive Removal of Methyl Red from Aqueous Solution using Charred and Xanthated Sal (Shorea robusta) Sawdust

2020 ◽  
Vol 1 (1) ◽  
pp. 37-44
Author(s):  
Krishna Bahadur Dawadi ◽  
Mahesh Bhattarai ◽  
Puspa Lal Homagai
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Low Cost ◽  
Ion Concentration ◽  
Maximum Adsorption Capacity ◽  
Methyl Red ◽  
Adsorptive Removal ◽  
Shorea Robusta ◽  
Chemically Modified ◽  
Saw Dust

Adsorptive removal of methyl red (MR) from aqueous solution onto chemically modified Charred Sal (Shorea robusta) Saw-Dust (CSSD) and Xanthated Sal Saw-Dust (XSSD) has been investigated. The surface modification is characterized by Fourier transformed infra-red (FTIR) spectroscopy, scanning electron microscopy (SEM) and elemental Analysis. Different parameters are studied such as contact time, optimum pH, and initial ion concentration. Maximum dye removal is observed at pH 4 for charred and xanthated Sal saw dust. The dye can be quantitatively removed onto the surface of these adsorbent. At a contact time of 3-4 hours maximum adsorption capacity (qmax) for CSSD and XSSD are found to be 70 mg/g and 130 mg/g respectively. Adsorption kinetic data are best fitted onto pseudo second order. The obtained result indicated an excellent alternative for the treatment of dye contaminated waste water using such chemically modified Sal saw dust at low cost with better efficiency.

Sign in / Sign up

Export Citation Format

Share Document