scholarly journals Fabrication and Uniaxial Tensile Properties of Soldered Porous Copper Fiber-Sintered Sheets

2019 ◽  
Vol 2019 ◽  
pp. 1-8
Author(s):  
Ruiliang Liu ◽  
Wei Zhou ◽  
Shuangli Li ◽  
Dongsheng Xu
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Solid Phase ◽  
Uniaxial Tensile ◽  
Elongation At Break ◽  
Porous Copper ◽  
Fluxless Soldering ◽  
The Difference ◽  
Free Solder ◽  
Sintering Method

Porous copper fiber-sintered sheets (PCFSSs) with different porosities were fabricated through the solid-phase sintering method using cutting copper fibers. PCFSSs with the same porosity and different porosities were then joined via a fluxless soldering method. By analyzing the uniaxial tensile property of the PCFSSs, the formation mechanism of the soldered PCFSSs was investigated. The difference in the tensile properties between the soldered and original PCFSSs was examined. Experimental results indicated that, for the PCFSSs with homogeneous porosity, reducing the porosity increased the tensile strength and elongation at break significantly. The fluxless soldering method with the lead-free solder resulted in excellent joining of the PCFSSs with the same porosity and different porosities. Moreover, the final tensile strength of the soldered PCFSSs with the same porosity was nearly equal to that of their parent PCFSSs. The tensile strength of the soldered PCFSSs with different porosities depended on the higher-porosity section. After soldering the PCFSSs, Young’s modulus increased and the elongation at break reduced.

Tensile Properties of Polypropylene/Cocoa Pod Husk Biocomposites: Effect of Maleated Polypropylene

2013 ◽  
Vol 747 ◽  
pp. 645-648 ◽  
Author(s):  
Koay Seong Chun ◽  
Salmah Husseinsyah ◽  
Hakimah Osman
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Tensile Modulus ◽  
Melt Blending ◽  
Elongation At Break ◽  
Maleated Polypropylene ◽  
Matrix Interaction ◽  
Cocoa Pod Husk ◽  
Blending Process ◽  
Scanning Electron

Polypropylene/Cocoa Pod Husk (PP/CPH) biocomposites with different maleated polypropylene (MAPP) content were prepared via melt blending process using Brabender Plastrograph mixer. The tensile strength and tensile modulus of PP/CPH biocomposites increased with increasing of MAPP content. The PP/CPH biocomposites with 5 phr of MAPP showed the optimum improvement on tensile properties. However, the increased of MAPP content reduced the elongation at break of PP/CPH biocomposites. At 5 phr of MAPP content, PP/CPH biocomposites showed lowest elongation at break. Scanning electron microscope confirms the PP/CPH biocomposites with MAPP have better filler-matrix interaction and adhesion due to the effect of MAPP.

scholarly journals The effects of alkanolamide addition on cure characteristics, swelling behaviour and tensile properties of silica-filled natural rubber (NR) / chloroprene rubber (CR) blends

2018 ◽  
Vol 34 ◽  
pp. 01030 ◽  
Author(s):  
Indra Surya ◽  
Syahrul Fauzi Siregar ◽  
Hanafi Ismail
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Crosslink Density ◽  
Tensile Modulus ◽  
Palm Stearin ◽  
Swelling Behaviour ◽  
Elongation At Break ◽  
Cure Characteristics ◽  
Chloroprene Rubber

Effects of alkanolamide (ALK) addition on cure characteristics, swelling behaviour and tensile properties of silica-filled natural rubber (NR)/chloroprene rubber (CR) blends were investigated. The ALK was synthesized from Refined Bleached Deodorized Palm Stearin (RBDPS) and diethanolamine, and incorporated into the silica-filled NR/CR blends as a non-toxic rubber additive. The ALK loadings were 0.0, 1.0, 3.0, 5.0 and 7.0 phr. It was found that the ALK exhibited shorter scorch and cure times and higher elongation at break of the silica-filled NR/CR blends. The ALK also exhibited higher torque differences, tensile modulus and tensile strength at a 1.0 phr of ALK loading and then decreased with further increases in the ALK loading. The swelling measurement proved that the 1.0 phr loading of ALK caused the highest degree in crosslink density of the silica-filled NR/CR blends.

scholarly journals Kenaf Fibre Reinforced Polypropylene Composites: Effect of Cyclic Immersion on Tensile Properties

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
W. H. Haniffah ◽  
S. M. Sapuan ◽  
K. Abdan ◽  
M. Khalid ◽  
M. Hasan ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Room Temperature ◽  
Tap Water ◽  
Tensile Modulus ◽  
Polypropylene Composites ◽  
Preliminary Results ◽  
Kenaf Fibre ◽  
The Difference ◽  
Number Of Cycles

This research studied the degradation of tensile properties of kenaf fibre reinforced polypropylene composites due to cyclic immersion into two different solutions, as well as comparison of the developed composites’ tensile properties under continuous and cyclic immersion. Composites with 40% and 60% fibre loadings were immersed in tap water and bleach for 4 cycles. Each cycle consisted of 3 days of immersion and 4 days of conditioning in room temperature (28°C and 55% humidity). The tensile strength and modulus of composites were affected by fibre composition, type of liquid of immersion, and number of cycles. The number of immersion cycles and conditioning caused degradation to tensile strength and modulus of kenaf fibre reinforced polypropylene composites. Continuous and cyclic immersion in bleach caused tensile strength of the composites to differ significantly whereas, for tensile modulus, the difference was insignificant in any immersion and fibre loadings. However, continuous immersion in the bleach reduced the tensile strength of composites more compared to cyclic immersion. These preliminary results suggest further evaluation of the suitability of kenaf fibre reinforced polypropylene composites for potential bathroom application where the composites will be exposed to water/liquid in cyclic manner due to discontinuous usage of bathroom.

Effects of Polyvinylamine and Polyvinyl Alcohol on DOP Migration of PVC Film

2013 ◽  
Vol 411-414 ◽  
pp. 2993-2996
Author(s):  
Yu Pu Deng ◽  
Lin Xue Du ◽  
Xi Hong Li ◽  
Xia Liu ◽  
Hai Jiao Liu
Keyword(s):  
Tensile Strength ◽  
Thermogravimetric Analysis ◽  
Polyvinyl Alcohol ◽  
Tensile Properties ◽  
Migration Rate ◽  
Control Sample ◽  
Mixed Solution ◽  
The Novel ◽  
Elongation At Break ◽  
Pvc Film

The novel packaging was synthesised by coating polyvinyl chloride (PVC) film with Polyvinylamine/Polyvinyl alcohol (PVAm/PVA) mixture which can effectively inhibit the migration of DOP in this paper. The effect of PVAm/PVA mixture on inhibiting DOP migration was detected via extraction tests. The results showed that the novel packaging significantly reduced the migration rate of DOP compared with the control (PVC film). After 24h extracted by hexane 40% PVAm in mixture being coated on PVC had the lowest migration rate (6.20%) among the samples, while 7.60% is the migration rate of control sample. Tensile properties analysis indicated the elongation at break and tensile strength of samples coating PVAm/PVA higher than control sample. The thermogravimetric analysis demonstrated that the PVAm/PVA mixed solution can deduce thermogravimetric rate. Therefore, coating PVC with PVAm/PVA mixture is an effective approach to suppress the migration of DOP.

A Method for Estimating Uncertainty of Indentation Tensile Properties in Instrumented Indentation Test

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Eun-chae Jeon ◽  
Joo-Seung Park ◽  
Doo-Sun Choi ◽  
Kug-Hwan Kim ◽  
Dongil Kwon
Keyword(s):  
Tensile Strength ◽  
Yield Strength ◽  
Tensile Test ◽  
Tensile Properties ◽  
Indentation Test ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Test ◽  
Instrumented Indentation ◽  
Estimation Model ◽  
Instrumented Indentation Test

The instrumented indentation test, which measures indentation tensile properties, has attracted interest recently because this test can replace uniaxial tensile test. An international standard for instrumented indentation test has been recently legislated. However, the uncertainty of the indentation tensile properties has never been estimated. The indentation tensile properties cannot be obtained directly from experimental raw data as can the Brinell hardness, which makes estimation of the uncertainty difficult. The simplifying uncertainty estimation model for the indentation tensile properties proposed here overcomes this problem. Though the influence quantities are generally defined by experimental variances when estimating uncertainty, here they are obtained by calculation from indentation load-depth curves. This model was verified by round-robin test with several institutions. The average uncertainties were estimated as 18.9% and 9.8% for the indentation yield strength and indentation tensile strength, respectively. The values were independent of the materials’ mechanical properties but varied with environmental conditions such as experimental instruments and operators. The uncertainties for the indentation yield and tensile strengths were greater than those for the uniaxial tensile test. These larger uncertainties were caused by measuring local properties in the instrumented indentation test. The two tests had the same tendency to have smaller uncertainties for tensile strength than yield strength. These results suggest that the simplified model can be used to estimate the uncertainty in indentation tensile properties.

A fuzzy logic model for prediction of tensile properties of epoxy/glass fiber/silica nanocomposites

2017 ◽  
Vol 50 (6) ◽  
pp. 491-500 ◽  
Author(s):  
Sajjad Daneshpayeh ◽  
Amir Tarighat ◽  
Faramarz Ashenai Ghasemi ◽  
Mohammad Sadegh Bagheri
Keyword(s):  
Tensile Strength ◽  
Fuzzy Logic ◽  
Elastic Modulus ◽  
Glass Fiber ◽  
Tensile Properties ◽  
Fiber Content ◽  
Main Role ◽  
Elongation At Break ◽  
Silica Nanocomposites ◽  
Two Factors

The object of this work is to study and predict the tensile properties (tensile strength, elastic modulus, and elongation at break) of ternary nanocomposites based on epoxy/glass fiber/nanosilica using the fuzzy logic (FL). Two factors in three levels including glass fiber at 0, 5, and 10 wt% and nanosilica at 0, 0.5, and 1 wt% were chosen for adding to an epoxy matrix. From FL surfaces, it was found that the glass fiber content had a main role in the tensile properties of nanocomposites. The high levels of glass fiber content led to a significant increase in the elastic modulus and generally, the presence of glass fiber decreased the tensile strength and elongation at break. Also, addition of the nanosilica content resulted in an increased elastic modulus but decreased the elongation at break of nanocomposites. Finally, an FL model was obtained for each tensile property.

Tensile Properties and Morphology of Low Linear Density Polyethylene/Kapok Husk Eco-Composites

2015 ◽  
Vol 754-755 ◽  
pp. 161-165
Author(s):  
Nurul Fatin Syazwani binti Arshad ◽  
Salmah Husseinsyah ◽  
Lim Bee Ying
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Modulus Of Elasticity ◽  
Interfacial Adhesion ◽  
Linear Density ◽  
Filler Content ◽  
Rotor Speed ◽  
Elongation At Break ◽  
Morphology Study

This research focused on the utilization of kapok husk (KH) as filler in low linear density polyethylene (LLDPE). The effect of filler content on tensile properties and morphology of LLDPE/KH eco-composites were investigated. The eco-composites were prepared by using Brabender Plasticiser EC Plus at temperature 160 °C and rotor speed 50 rpm. The results indicated that the tensile strength and elongation at break decreased with KH content increased. However, the modulus of elasticity increased with increasing of KH content. The morphology study of eco-composites exhibit poor interfacial adhesion between KH and LLDPE.

scholarly journals Fishing efficiency of biodegradable PBSAT gillnets and conventional nylon gillnets used in Norwegian cod (Gadus morhua) and saithe (Pollachius virens) fisheries

2018 ◽  
Vol 75 (6) ◽  
pp. 2245-2256 ◽  
Author(s):  
Eduardo Grimaldo ◽  
Bent Herrmann ◽  
Jørgen Vollstad ◽  
Biao Su ◽  
Heidi Moe Føre ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Gadus Morhua ◽  
Plastic Pollution ◽  
Elongation At Break ◽  
Northern Norway ◽  
Before And After ◽  
Polybutylene Succinate ◽  
The Difference ◽  
Catch Rates

Abstract Fishing trials were carried out to compare the relative fishing efficiency of gillnets made of a new biodegradable resin (polybutylene succinate co-adipate-co-terephthalate, PBSAT) with conventional (nylon) nets. The fishing trials covered two consecutive fishing seasons (2016 and 2017) for cod (Gadus morhua) and saithe (Pollachius virens) in northern Norway. Results generally showed better catch rates for the nylon gillnets. The biodegradable PBSAT gillnets caught 50.0% and 26.6% fewer cod, and 41.0% and 22.5% fewer saithe than the nylon gillnets in 2016 and 2017, respectively. Even though the relative catch efficiency of the biodegradable gillnets was slightly better in 2017 than in 2016, the difference with respect to the catch efficiency of nylon gillnets may be too large for biodegradable gillnets to be accepted by fishermen if they were available commercially. Tensile strength measurements of the nylon and biodegradable PBSAT gillnets carried out before and after the fishing trials showed that the both types of gillnets had significant reductions in tensile strength and elongation at break, especially in 2017. Although less catch efficient than nylon gillnets, biodegradable PBSAT gillnets show great potential for reducing ghost fishing and plastic pollution at sea, which are major problems in these fisheries.

scholarly journals Mechanical and Thermal Properties of Poly(urethane urea) Nanocomposites Prepared with Diamine-Modified Laponite

2008 ◽  
Vol 2008 ◽  
pp. 1-9 ◽  
Author(s):  
Joe-Lahai Sormana ◽  
Santanu Chattopadhyay ◽  
J. Carson Meredith
Keyword(s):  
Tensile Strength ◽  
Thermal Properties ◽  
Tensile Properties ◽  
Particle Concentration ◽  
Chain Extender ◽  
Mechanical And Thermal Properties ◽  
Elongation At Break ◽  
Hard Domain ◽  
A Chain

Nanocomposites based on segmented poly(urethane urea) were prepared by reacting a poly(diisocyanate) with diamine-modified Laponite-RD nanoparticles that served as a chain extender. The nanocomposites were prepared at a constantNH2to NCO mole ratio of 0.95, while varying the fraction of diamine-modified Laponite relative to the free diamine chain extender. Compared to neat poly(urethane urea), all nanocomposites showed increased tensile strength and elongation at break. As Laponite loading increased, tensile properties passed through a maximum at a particle concentration of 1 mass%, at which a 300% increase in tensile strength and 40% increase in elongation at break were observed. A maximum in urea and urethane hard-domain melting endotherms was also observed at this Laponite loading. Optimal mechanical and thermal properties coincided with a minimum in the size of the inorganic Laponite phase. Nanocomposites containing diamine-modified Laponite had higher tensile strengths than those with nonreactive monoamine-modified Laponite or diamine-modified Cloisite.

Preparation and Properties of Sponge Rubber Based on Natural Rubber and Cassava Starch

2014 ◽  
Vol 931-932 ◽  
pp. 68-72
Author(s):  
Komsun Temna ◽  
Nitinart Saetung ◽  
Anuwat Saetung
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Cassava Starch ◽  
Interfacial Interaction ◽  
Morphological Properties ◽  
Elongation At Break ◽  
Cure Time ◽  
The Difference ◽  
Cure Characteristic

In this work, the sponge rubbers based on cassava starch masterbatch in latex phase with the difference technique (non-gelatinized and gelatinized cassava starch) were preformed. The cassava starch contents from 0 to 70 phr were also studied. The cure characteristic, mechanical and morphological properties were investigated. It was found that the scorch time and cure time were increased with an increasing of cassava starch contents in both techniques. The mechanical properties i.e., tensile strength, elongation at break and tear strength were decreased with an increasing of cassava starch contents, except 500% modulus. However, the sponge based on gelatinized technique gave the better mechanical properties than that of non-gelatinized cassava starch. The SEM micrographs of sponge NR from gelatinized technique were also able to confirm a good interfacial interaction between hydrophilic cassava starch and hydrophobic NR.

Sign in / Sign up

Export Citation Format

Share Document