Tensile Properties of Polypropylene/Cocoa Pod Husk Biocomposites: Effect of Maleated Polypropylene

2013 ◽  
Vol 747 ◽  
pp. 645-648 ◽  
Author(s):  
Koay Seong Chun ◽  
Salmah Husseinsyah ◽  
Hakimah Osman
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Tensile Modulus ◽  
Melt Blending ◽  
Elongation At Break ◽  
Maleated Polypropylene ◽  
Matrix Interaction ◽  
Cocoa Pod Husk ◽  
Blending Process ◽  
Scanning Electron

Polypropylene/Cocoa Pod Husk (PP/CPH) biocomposites with different maleated polypropylene (MAPP) content were prepared via melt blending process using Brabender Plastrograph mixer. The tensile strength and tensile modulus of PP/CPH biocomposites increased with increasing of MAPP content. The PP/CPH biocomposites with 5 phr of MAPP showed the optimum improvement on tensile properties. However, the increased of MAPP content reduced the elongation at break of PP/CPH biocomposites. At 5 phr of MAPP content, PP/CPH biocomposites showed lowest elongation at break. Scanning electron microscope confirms the PP/CPH biocomposites with MAPP have better filler-matrix interaction and adhesion due to the effect of MAPP.

The Effect of Different Sizes "Batu Reput" (Dolomite) as a Filler in SMR L and ENR-50

2013 ◽  
Vol 795 ◽  
pp. 383-387 ◽  
Author(s):  
J.N.M. Ridhwan ◽  
N.Z. Noimam ◽  
M.A.A. Mohd Salleh ◽  
S.T. Sam ◽  
L. Musa ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Epoxidized Natural Rubber ◽  
Morphological Properties ◽  
Elongation At Break ◽  
Matrix Interaction ◽  
Scanning Electron

The effects of different sizes of Batu Reput (Dolomite) filler which are smaller size (<63μm) and bigger size (75-150μm) on tensile and morphological properties of Batu Reput (Dolomite) filled SMR L and epoxidized natural rubber (ENR-50) blends were investigated. Results indicated that, the tensile properties, such as tensile strength (TS), elongation at break (Eb) and stress at 100% elongation (M100) of Batu Reput (Dolomite) filled SMR L higher than Batu Reput (Dolomite) filled ENR-50 blends, particularly, at 15 phr of smaller size of Batu Reput (Dolomite). The scanning electron microscopy studies proved, Batu Reput (Dolomite) filled SMR L illustrated a higher Batu Reput (Dolomite) - SMR L matrix interaction compared with Batu Reput (Dolomite) filled ENR-50.

scholarly journals The effects of alkanolamide addition on cure characteristics, swelling behaviour and tensile properties of silica-filled natural rubber (NR) / chloroprene rubber (CR) blends

2018 ◽  
Vol 34 ◽  
pp. 01030 ◽  
Author(s):  
Indra Surya ◽  
Syahrul Fauzi Siregar ◽  
Hanafi Ismail
Keyword(s):  
Tensile Strength ◽  
Natural Rubber ◽  
Tensile Properties ◽  
Crosslink Density ◽  
Tensile Modulus ◽  
Palm Stearin ◽  
Swelling Behaviour ◽  
Elongation At Break ◽  
Cure Characteristics ◽  
Chloroprene Rubber

Effects of alkanolamide (ALK) addition on cure characteristics, swelling behaviour and tensile properties of silica-filled natural rubber (NR)/chloroprene rubber (CR) blends were investigated. The ALK was synthesized from Refined Bleached Deodorized Palm Stearin (RBDPS) and diethanolamine, and incorporated into the silica-filled NR/CR blends as a non-toxic rubber additive. The ALK loadings were 0.0, 1.0, 3.0, 5.0 and 7.0 phr. It was found that the ALK exhibited shorter scorch and cure times and higher elongation at break of the silica-filled NR/CR blends. The ALK also exhibited higher torque differences, tensile modulus and tensile strength at a 1.0 phr of ALK loading and then decreased with further increases in the ALK loading. The swelling measurement proved that the 1.0 phr loading of ALK caused the highest degree in crosslink density of the silica-filled NR/CR blends.

Corn Cob Filled Chitosan Biocomposite Films

2013 ◽  
Vol 747 ◽  
pp. 649-652 ◽  
Author(s):  
Chan Ming Yeng ◽  
Husseinsyah Salmah ◽  
Sung Ting Sam
Keyword(s):  
Tensile Properties ◽  
Interfacial Adhesion ◽  
Tensile Modulus ◽  
Solvent Casting ◽  
Corn Cob ◽  
Casting Method ◽  
Elongation At Break ◽  
The Poor ◽  
Biocomposite Films ◽  
Scanning Electron

Recently, there has been renews interest in chitosan as materials in producing of biocomposite films. The chitosan (CS)/corn cob (CC) biocomposite films were prepared by solvent casting method. The effect of CC content on tensile properties of CS/CC biocomposite films was studied. The tensile strength and elongation at break of CS/CC biocomposite films decreased as increasing of CC content. However, the increasing of CC content was increased the tensile modulus of CS/CC biocomposite films. Scanning electron microscopy (SEM) was indicated that the deceasing of tensile properties was due to the poor interfacial adhesion between CC filler and CS matrix.

scholarly journals Investigation on tensile properties of epoxy/graphene nano-platelets/carboxylated nitrile butadiene rubber ternary nanocomposites using response surface methodology

2019 ◽  
Vol 9 ◽  
pp. 184798041985584 ◽  
Author(s):  
Mohammadhossein Saberian ◽  
Faramarz Ashenai Ghasemi ◽  
Ismail Ghasemi ◽  
Sajjad Daneshpayeh
Keyword(s):  
Tensile Strength ◽  
Response Surface Methodology ◽  
Tensile Properties ◽  
Response Surface ◽  
Tensile Modulus ◽  
Curing Temperature ◽  
Butadiene Rubber ◽  
Elongation At Break ◽  
Low Concentration ◽  
Nitrile Butadiene Rubber

In this study, the response surface methodology was used to investigate the tensile properties of epoxy/graphene nano-platelets/carboxylated nitrile butadiene rubber ternary nanocomposites. Box–Benhken method was used to design experiments for four factors consisting of graphene nano-platelets (at 0, 0.75, and 1.5 wt%), carboxylated nitrile butadiene rubber (0, 5, and 10 wt%), hardener contents (80, 90, and 100 phr), and also different post curing temperature (130, 140, and 150°C). After the samples were prepared, a tensile test was performed to obtain the tensile strength, tensile modulus, and elongation at break of nanocomposites. Moreover, field-emission scanning electron microscopy was used to observe the state of graphene nano-platelets dispersion. The results obtained from the tensile tests showed that increasing the graphene nano-platelets, carboxylated nitrile butadiene rubber, and hardener contents and high post curing temperature reduced the tensile strength. The optimum value of tensile modulus was achieved at low concentration of carboxylated nitrile butadiene rubber and high contents of graphene nano-platelets, whereas maximum elongation at break occurred at high content of carboxylated nitrile butadiene rubber and low concentration of graphene nano-platelets and hardener. In addition, a second-order polynomial model was used to correlate the tensile properties of ternary nanocomposites to the desired factors. Finally, contour plots were used to determine optimum values of the desired factors. It was seen that the presence of 10 wt% of carboxylated nitrile butadiene rubber in the epoxy matrix increased the elongation at break by the considerable amount of ∼49%.

scholarly journals Simultaneous Improvement in the Tensile and Impact Strength of Polypropylene Reinforced by Graphene

2020 ◽  
Vol 2020 ◽  
pp. 1-5
Author(s):  
Li Juan
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Tensile Strength ◽  
Fracture Surface ◽  
Impact Strength ◽  
Melt Blending ◽  
Elongation At Break ◽  
Morphological Behavior ◽  
Scanning Electron

The nanocomposites of polypropylene (PP)/graphene were prepared by melt blending. The effects of the dosage of graphene on the flow and mechanical properties of the nanocomposites were investigated. The morphologies of fracture surfaces were characterized through scanning electron microscopy (SEM). The graphene simultaneous enhanced tensile and impact properties of nanocomposites. A 3.22% increase in tensile strength, 39.8% increase in elongation at break, and 26.7% increase in impact strength are achieved by addition of only 1 wt.% of graphene loading. The morphological behavior indicates the fracture surface of PP/graphene is more rough than that of pure PP.

Effects of Impregnation Time on Physical and Tensile Properties of Impregnated Sugar Palm (Arenga pinnata) Fibres

2011 ◽  
Vol 471-472 ◽  
pp. 1147-1152 ◽  
Author(s):  
M.R. Ishak ◽  
Zulkiflle Leman ◽  
S.M. Sapuan ◽  
M.Z.A. Rahman ◽  
U.M.K. Anwar
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Phenol Formaldehyde ◽  
Unsaturated Polyester ◽  
Tensile Modulus ◽  
Elongation At Break ◽  
Strain Behavior ◽  
Significant Difference ◽  
Impregnation Time ◽  
Lower Tensile Strength

The aim of this study is to investigate the effect of impregnation time on physical and tensile properties of sugar palm (Arenga pinnata) fibres. The fibre was impregnated with phenol formaldehyde (PF) and unsaturated polyester (UP) with various impregnation times (0, 5, 10, 15, 20, 25 min) at constant impregnation pressure of 1000 mmHg, before it was released within 30 s. Significant improvement in physical properties was observed after being impregnated for 5 min especially for fibre impregnated with PF due to its low moisture content (MC) and water absorption (WA). However, no significant changes in specific gravity for both impregnated fibres were observed. Fibre impregnated with UP for 5 min shows notable improvement in tensile strength and better fibre toughness while the fibre impregnated with PF showed lower tensile strength and elongation at break and higher tensile modulus than un-impregnated fibre. Since the PF-impregnated fibre become brittle and results in lower fibre toughness as shown in the stress strain behavior, this causes for poor fibre properties. However, there was no significant difference (p≤0.05) between all impregnated fibres in physical and tensile properties after impregnation time was extended from 10 to 25 min. In general, by increasing time of impregnation did not give much effect in improving physical and tensile properties of fibres.

scholarly journals Effect of Soil Burial on Tensile Properties of Polypropylene/Plasticized Cassava Starch Blends

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
Henry C. Obasi ◽  
Isaac O. Igwe ◽  
Innocent C. Madufor
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Starch Content ◽  
Cassava Starch ◽  
Melt Blending ◽  
Elongation At Break ◽  
Soil Burial ◽  
Starch Blends ◽  
Plasticized Starch ◽  
Burial Time

Polypropylene (PP)/plasticized cassava starch (PCS) blended with and without compatibilizer (polypropylene-graft-maleic anhydride (PP-g-MA)) via melt blending were prepared for soil burial which lasted for 90 days. Plasticized starch loadings of 0, 10, 20, 30, 40, and 50 wt.% were used, while pp-g-ma was used at 10 wt.% based on starch weight. The PP/PCS and PP/PCS/PP-G-MA blends were evaluated for their tensile properties. It was observed that the tensile strength, elongation at break, and young’s modulus decreased with increases in soil burial time as well as starch content for PP/PCS blends. Similar treads for the tensile properties were observed for PP/PCS/PP-g-MA, but with higher properties as compared to uncompatibilized blends. However, the tensile properties for both PP/PCS and PP/PCS/PP-g-Ma decrease with increases in starch loading and also as the burial period progressed.

Study the Effect of the Addition of HAp from Crocodile Bones on the Mechanical Properties of PLA/HAp Composites

2013 ◽  
Vol 834-836 ◽  
pp. 237-240 ◽  
Author(s):  
Kanyakorn Pawarangkool ◽  
Wirunya Keawwattana
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Thermal Process ◽  
Weight Ratio ◽  
Melt Blending ◽  
Elongation At Break ◽  
X Ray ◽  
Infrared Spectrometer ◽  
Scanning Electron

In this work, hydroxyapatite (HAp) was produced from crocodile bones by thermal process at 900°C. X-ray diffractometer (XRD), Fourier transform infrared spectrometer (FTIR) and Scanning electron microscope (SEM) were used to characterize the obtained HAp. Polylactic acid (PLA)/HAp composites were prepared by melt blending as follows: 95/5, 90/10 and 85/15 (weight ratio). The effect of the amount of HAp on the mechanical properties including tensile strength, modulus, elongation at break and impact strength of PLA/HAp composites was undertaken. It was found that tensile strength and elongation at break of the composites decreased with an increase of HAp content, while modulus and impact strength showed no significant effect.

Properties of Compatibilized SAN/NR Blends

2012 ◽  
Vol 488-489 ◽  
pp. 62-66
Author(s):  
Jareenuch Rojsatean ◽  
Supakij Suttireungwong ◽  
Manus Seadan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Maleic Anhydride ◽  
Impact Strength ◽  
Melt Blending ◽  
Elongation At Break ◽  
Reactive Agents ◽  
Internal Mixer ◽  
Scanning Electron

The blend of poly(styrene-co-acrylonitrile) (SAN) and natural rubber (NR) is immiscible and incompatible which lead to poor mechanical properties. Many methods can be carried out to improve the compatibility. In this work, the potential of various reactive compatibilizers in SAN and NR blend was explored. The morphological and mechanical properties were compared. The melt blending of SAN and NR were prepared in an internal mixer with various types of reactive agent such as styrene-co-maleic anhydride (SMA), maleic anhydride (MA), peroxide and mixed reactive agents. The morphological textures of the blends were investigated by scanning electron microscope. Mechanical properties including tensile strength, impact strength and elongation at break were measured. The results of morphological observations revealed that SAN/NR blend with reactive agent, the mixture of SMA and MA show the smallest and the most uniform dispersed NR particles, where the size of NR particle is about 1 µm. The mechanical properties of the blends revealed impact strength and elongation at break were increased with addition of reactive agents. SAN/NR blend with the mixture of SMA and MA showed the highest elongation at break but it had lower impact strength than the blend with SMA.

The Study of Mechanical Properties and Morphology of Recycled Nitrile Glove Filled Epoxidized Natural Rubber Compounds (NBRr/ENR25)

2015 ◽  
Vol 754-755 ◽  
pp. 130-134 ◽  
Author(s):  
A.A. Afiratul ◽  
N.Z. Noimam ◽  
S.T. Sam ◽  
Hanafi Ismail ◽  
Mohamad Kahar Ab Wahab ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Properties ◽  
Room Temperature ◽  
Elongation At Break ◽  
Matrix Interaction ◽  
Rubber Compounds ◽  
Roll Mill ◽  
Increasing Trend ◽  
Fine Size ◽  
Scanning Electron

The effects of mechanical properties (tensile properties and resilience test) and morphology of recycled nitrile glove (NBRr) filled epoxidized natural rubbers (ENR25) were examined. Two different size ranges of NBRr particles, i.e., S1 (250μm-500μm) and S2(2cm-5cm) were used in this study. The NBRr/ENR25 compounds with five different compositions of NBRr (5, 15, 25, 35 and 50 phr) were prepared using a two roll-mill at room temperature. The result indicated that the tensile properties such as tensile strength and elongation at break decreased as the ratio of NBRr increased. Meanwhile stress at 100% elongation show an increasing trend with the addition of recycled nitrile glove in ENR25. The resilience properties of NBRr/ENR25 compounds decreased when NBRr loading increased. The scanning electron microscopy studies showed that the fine size, S1 of NBRr particles in NBRr/ENR25 compounds illustrated a better NBRr-ENR25 matrix interaction compared with coarse size, S2 of NBRr particles. The results overall indicated that the NBRr/ENR25 with fine size, S1 of NBRrparticles show better mechanical properties (tensile properties and resilience properties) and morphology compared to coarse size, S2 of NBRr particles.

Sign in / Sign up

Export Citation Format

Share Document