scholarly journals Efficiency of Sawdust as Low-Cost Adsorbent for Dyes Removal

2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
R. Chikri ◽  
N. Elhadiri ◽  
M. Benchanaa ◽  
Y. El maguana
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Base Material ◽  
Isotherm Models ◽  
Extensive Literature ◽  
Effective Technique ◽  
Adsorption Isotherm Models ◽  
Harmful Effects ◽  
Dyes Removal

In recent years, the removal of dyes from wastewater has attracted considerable attention due to their harmful effects to ecosystem and human health. Adsorption as a facile and effective technique has been widely used to eliminate a large variety of dyes from aqueous solutions. Activated carbon is the most preferred adsorbent to treat wastewater but its use is limited because of high cost. Therefore, several low-cost and natural materials and wastes have been used as precursors for the preparation of alternative adsorbents. Among them, sawdust as an abundant and low-cost by-product has been explored as adsorbent for the removal of dyes from wastewater. This review focuses on the various sawdust used as a precursor for the preparation of activated carbons. Extensive literature information about sawdust, its compositions, activation methods, its efficiency for dyes removal, and environmental conditions effects has been reviewed. The applicability of various adsorption kinetic models and adsorption isotherm models for dye removal by sawdust-derived activated carbons has been also reported. Finally, this paper highlights the use of sawdust as base material for various composites and mixture which can be used as granular activated carbon.

Removal of Dyes From Wastewater by Adsorption Onto Low-Cost Adsorbents

2020 ◽  
pp. 239-257
Author(s):  
Victor Odhiambo Shikuku ◽  
George Oindo Achieng' ◽  
Chrispin O. Kowenje
Keyword(s):  
Activated Carbons ◽  
Low Cost ◽  
Dye Adsorption ◽  
Environmental Parameters ◽  
Isotherm Models ◽  
Treatment Technique ◽  
Operational Conditions ◽  
Adsorption Isotherm Models ◽  
Inorganic Adsorbents

This chapter describes an up-to-date critique of the use of adsorption as a wastewater treatment technique for the removal of dyes. The topics range from the classification of dyes, their occurrence in water and toxicity, various treatment methods, and dye adsorption dynamics onto agricultural wastes and inorganic adsorbents such as clay and metal oxides and adsorption onto microbial biomass under varying operational conditions. It is demonstrated that the discussed materials form alternative adsorbents for dye adsorption from aqueous solutions with comparable or better removal efficiencies relative to the non-renewable coal-based granular activated carbons; they are cheap and abundant. The relative performance of the adsorbents under different environmental parameters for dye removal has also presented. The deductions made and alluded to from various kinetic and adsorption isotherm models are also discussed. The chapter presents the past, present, and suggestions for future considerations in search of non-conventional adsorbents for dye sequestration from aqueous solution.

Dynamic Study of Adsorption for the Removal of Bismark Brown – Using Activated Carbons

2011 ◽  
Vol 671 ◽  
pp. 187-204
Author(s):  
A. Xavier ◽  
R Sathya ◽  
J. Gandhi Rajan ◽  
R. Nagarathnam
Keyword(s):  
Activated Carbon ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Low Cost ◽  
Kinetic Equations ◽  
Dye Adsorption ◽  
Industrial Wastes ◽  
Isotherm Models ◽  
Before And After ◽  
Intra Particle Diffusion

Many industries use dyes and pigments to colorize their products. Large amount different types of dyes enter in to the environment. These dyes are invariably left in the industrial wastes. As a part of removal of Bismark Brown dye from textile and leather industrial wastes, using activated carbon as adsorbents namely, commercial activated carbon (CAC), rose apple carbon (RAC), coconut shell carbon (CSC) and saw dust carbon (SDC). The percentage removal of Bismark-Brown adsorbed increases with decrease in initial concentration and particle size of adsorbent and increased with increase in contact time, temperature and dose of adsorbent. The pH is highly sensitive for dye adsorption process. The adsorption process followed first order kinetics and the adsorption data with Freundlich and Langmuir isotherm models. The first kinetic equations like Natarajan Khalaf, Lagergren, Bhattacharya and Venkobhachar and intra-particle diffusion were found to be applicable. A comparative account of the adsorption capacity of various carbons has been made. These activated carbons are alternative to commercial AC for the removal dyes in General and Bismark-brown (BB) is particular. These results are reported highly efficient and effective and low cost adsorbent for the BB. The thermodynamics parameters are also studied and it obeys spontaneous process. The results are confirmed by before and after adsorption process with the help of the following instrumental techniques viz., FT-IR, UV-Visible Spectrophotometer and SEM analyze.

scholarly journals Removal of Ni (II) from Aqueous Solution by Adsorption onto Activated Carbon Prepared from Lapsi (Choerospondias axillaris) Seed Stone

2014 ◽  
Vol 9 (1) ◽  
pp. 166-174 ◽  
Author(s):  
Rajeshwar M. Shrestha ◽  
Margit Varga ◽  
Imre Varga ◽  
Amar P. Yadav ◽  
Bhadra P. Pokharel ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Characterization ◽  
Maximum Adsorption Capacity ◽  
Adsorption Data ◽  
Optimum Ph ◽  
Nickel Adsorption

Activated carbons were prepared from Lapsi seed stone by the treatment with H2SO4 and HNO3 for the removal of Ni (II) ions from aqueous solution. Two activated carbon have been prepared from Lapsi seed stones by treating with conc.H2SO4 and a mixture of H2SO4 and HNO3 in the ratio of 1:1 by weight for removal of Ni(II) ions. Chemical characterization of the resultant activated carbons was studied by Fourier Transform Infrared Spectroscopy and Boehm titration which revealed the presence of oxygen containing surface functional groups like carboxyl, lactones and phenols in the carbons. The optimum pH for nickel adsorption is found to be 5. The adsorption data were better fitted with the Langmuir equations than Freundlich adsorption equation to describe the equilibrium isotherms. The maximum adsorption capacity of Ni (II) on the resultant activated carbons was 28.25.8 mg g-1 with H2SO4 and 69.49 mg g-1 with a mixture of H2SO4 and HNO3. The waste material used in the preparation of the activated carbons is inexpensive and readily available. Hence the carbons prepared from Lapsi seed stones can act as potential low cost adsorbents for the removal of Ni (II) from water. DOI: http://dx.doi.org/10.3126/jie.v9i1.10680Journal of the Institute of Engineering, Vol. 9, No. 1, pp. 166–174

Point-of-entry adsorbers for the removal of fumigants

1995 ◽  
Vol 22 (1) ◽  
pp. 106-120
Author(s):  
Roberto M. Narbaitz ◽  
Frances Z. Parsons ◽  
Tsong-Yih Tzeng
Keyword(s):  
Organic Matter ◽  
Activated Carbon ◽  
Low Cost ◽  
Scale Up ◽  
Extensive Literature ◽  
Limited Data ◽  
Ethylene Dibromide ◽  
Point Of Entry ◽  
Naturally Occurring ◽  
Adsorption Data

Point-of-entry systems with granular activated carbon filters have been used extensively to provide safe water to rural homes with wells contaminated with synthetic organic chemicals. Because of the low cost of these systems, their design is generally based on the equilibrium column model, the isotherm data from the literature, and a scale-up factor. This paper analyzes the necessary scale-up factors for point-of-entry adsorbers based on fumigant adsorption data gathered through an extensive literature review. The fumigants evaluated are 1,2-dichloropropane, 1,2-dibromo-3-chloropropane, and ethylene dibromide. It was impossible to thoroughly assess the scale-up factors for 1,2-dichloropropane because of the limited data. Column data for the other two fumigants were sufficient to generate column loading lines, which can be used directly without resorting to scale-up factors. Column data showed that the scale-up factors are greatly affected by competitive adsorption with the naturally occurring background organic matter and by preloading of these organic matter. As these phenomena are not well understood, it is presently impossible to accurately predict the appropriate scale-up factors. A recommended design approach is outlined. Key words: adsorption, activated carbon, fumigants, point-of-entry.

scholarly journals Optimisation of durian peel based activated carbon preparation conditions for dye removal

2013 ◽  
Vol 16 (1) ◽  
pp. 22-31
Author(s):  
Phung Thi Kim Le ◽  
Kien Anh Le
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Surface Area ◽  
Dye Removal ◽  
Activated Carbons ◽  
Low Cost ◽  
Waste Water Treatment ◽  
Impregnation Ratio ◽  
Carbon Production ◽  
Removal Capacity

Agricultural wastes are considered to be a very important feedstock for activated carbon production as they are renewable sources and low cost materials. This study present the optimize conditions for preparation of durian peel activated carbon (DPAC) for removal of methylene blue (MB) from synthetic effluents. The effects of carbonization temperature (from 673K to 923K) and impregnation ratio (from 0.2 to 1.0) with potassium hydroxide KOH on the yield, surface area and the dye adsorbed capacity of the activated carbons were investigated. The dye removal capacity was evaluated with methylene blue. In comparison with the commercial grade carbons, the activated carbons from durian peel showed considerably higher surface area especially in the suitable temperate and impregnation ratio of activated carbon production. Methylene blue removal capacity appeared to be comparable to commercial products; it shows the potential of durian peel as a biomass source to produce adsorbents for waste water treatment and other application. Optimize condition for preparation of DPAC determined by using response surface methodology was at temperature 760 K and IR 1.0 which resulted the yield (51%), surface area (786 m2/g), and MB removal (172 mg/g).

scholarly journals A Comparative Study of COD Removal Efficacy from Pharmaceutical Wastewater by Areca Nut Husk Produced and Commercially Available Activated Carbons

2021 ◽  
pp. 47-56
Author(s):  
Sharmin Akter ◽  
Ferdousi Sultana ◽  
Md. Rakibul Kabir ◽  
Partha Pratim Brahma ◽  
Atkeeya Tasneem ◽  
...  
Keyword(s):  
Experimental Data ◽  
Activated Carbon ◽  
Organic Contaminants ◽  
Activated Carbons ◽  
Low Cost ◽  
Oxygen Demand ◽  
Areca Nut ◽  
Pharmaceutical Wastewater ◽  
Adsorption Processes ◽  
Pharmaceutical Industries

Pharmaceutical industries in Bangladesh are considered as one major industrial as well as environmental pollution problems which discharge a significant amount of organic contaminants in the environment hence require advanced treatment technologies to decontaminate pharmaceutical wastewater. In the present investigation, areca nut husk treated activated carbon (ANHC) was used as an adsorbent to remove chemical oxygen demand (COD) from pharmaceutical effluent as well as a comparative adsorption efficiency with commercial activated carbon (CAC) was performed.  The batch experiments were carried out in a laboratory scale. The materials also evaluated for different adsorbent dosages and contact times. The experiment revealed a removal percentage up to 70% for ANHC and 90% for CAC for 3g of adsorbents in 180 min. The adsorption processes were satisfactorily described by pseudo-second-order (PSO) kinetic model which shows a better fitting with the maximum regression coefficient for both adsorbents. The results show that Langmuir model best described the experimental data with a highest correlation coefficient (R2=0.9856 for ANHC and 0.9993 for CAC) compared to Freundlich model and the experimental data showed asorption capacity of 36.549 and 64.935 mg/g for ANHC and CAC, correspondingly. According to the adsorption studies, the results revealed that COD adsorption process followed by the monolayer chemisorption mechanisms. The results revealed that ANHC adsorbent is potentially low cost and environmental friendly adsorbent for the removal of organic matter from pharmaceutical effluent.

scholarly journals Waste biomass as sources for activated carbon production-A review

2013 ◽  
Vol 47 (4) ◽  
pp. 347-364 ◽  
Author(s):  
MS Islam ◽  
MA Rouf
Keyword(s):  
Activated Carbon ◽  
Process Parameters ◽  
Activated Carbons ◽  
Low Cost ◽  
Process Conditions ◽  
Waste Biomass ◽  
Active Carbons ◽  
Carbon Production ◽  
Surface Areas ◽  
Physical And Chemical

A review of the production of activated carbons from waste biomass has been presented. The effects of various process parameters on the pyrolysis stage have been reviewed. Influences of activating conditions, physical and chemical, on the active carbon properties have been discussed. Under certain process conditions several active carbons with BET surface areas, ranging between 250 and 2410 m2/g and pore volumes of 0.022 and 91.4 cm3/g, have been produced. A comparison in characteristics and uses of activated carbons from waste biomass with those of commercial carbons has been made. Waste biomass being highly efficient, low cost and renewable sources of activated carbon production. Bangladesh J. Sci. Ind. Res. 47(4), 347-364, 2012 DOI: http://dx.doi.org/10.3329/bjsir.v47i4.14064

scholarly journals Removal of Methylene Blue from Waste Water Using Activated Carbon Prepared from Rice Husk

2012 ◽  
Vol 60 (2) ◽  
pp. 185-189 ◽  
Author(s):  
Mohammad Arifur Rahman ◽  
S. M. Ruhul Amin ◽  
A. M. Shafiqul Alam
Keyword(s):  
Waste Water ◽  
Methylene Blue ◽  
Activated Carbon ◽  
Aqueous Solutions ◽  
Rice Husk ◽  
Flow Rate ◽  
Activated Carbons ◽  
Low Cost ◽  
Waste Water Treatment ◽  
Blue Dye

The possible utilization of rice husk activated carbon as an adsorbent for the removal of methylene blue dye from aqueous solutions has been investigated. In this study, activated carbons, prepared from low-cost rice husk by sulfuric acid and zinc chloride activation, were used as the adsorbent for the removal of methylene blue, a basic dye, from aqueous solutions. Effects of various experimental parameters, such as adsorbent dosage and particle size, initial dye concentration, pH and flow rate were investigated in column process. The maximum uptakes of methylene blue by activated rice husk carbon at optimized conditions (particle sizes: 140 ?m; Flow rate: 1.4 mL/min; pH: 10.0; initial volume of methylene blue: 50 mL and initial concentration of methylene blue: 4.0 mg/L etc.) were found to 97.15%. The results indicate that activated carbon of rice husk could be employed as low-cost alternatives to commercial activated carbon in waste water treatment for the removal of basic dyes. This low cost and effective removal method may provide a promising solution for the removal of crystal violet dye from wastewater.DOI: http://dx.doi.org/10.3329/dujs.v60i2.11491 Dhaka Univ. J. Sci. 60(2): 185-189, 2012 (July)

Removal of Methylene Blue by Adsorption Process - A Comparative Study

2011 ◽  
Vol 699 ◽  
pp. 245-264 ◽  
Author(s):  
A. Xavier ◽  
J. Gandhi Rajan ◽  
D. Usha ◽  
R Sathya
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Process ◽  
Activated Carbons ◽  
Low Cost ◽  
Kinetic Equations ◽  
Dye Adsorption ◽  
Industrial Wastes ◽  
Blue Dye ◽  
Molecular Formula

Methylene blue is a heterocyclic aromatic chemical compound with the molecular formula C16H18N3SCl. It has used in the biology and chemistry field. At room temperature, it appears as a solid, odourless dark green powder that yields blue solution when dissolved in water. As a part of removal of methylene blue dye from textile and leather industrial wastes, using activated carbon as adsorbents namely, commercial activated carbon (CAC), rose apple carbon (RAC), coconut shell carbon (CSC) and saw dust carbon (SDC). The percentage of Methylene blue adsorbed increases with decrease in initial concentration and particle size of adsorbent and increased with increase in contact time, temperature and dose of adsorbents. The pH is highly sensitive for dye adsorption process. The adsorption process followed first order kinetics and the adsorption data the modeled with Freundlich and Langmuir isotherms. The first kinetic equations like Natarajan Khalaf, Lagergren, Bhattacharya and Venkobhachar and intra particle diffusion were found to be applicable. A comparative account of the adsorption capacity of various carbons has been made. These activated carbons are alternative to commercial AC for the removal dyes in General and MB is particular. These results are reported highly efficient and effective and low cost adsorbent for the MB. The thermodynamics parameters are also studied and it obeys spontaneous process. The results are confirmed by before and after adsorption process with the help of the following instrumental techniques viz., FT-IR, UV-Visible Spectrophotometer and SEM photos.

scholarly journals Comparison of Surface and Structural Properties of Carbonaceous Materials Prepared by Chemical Activation of Tomato Paste Waste: The Effects of Activator Type and Impregnation Ratio

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Nurgul Ozbay ◽  
Adife Seyda Yargic
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Low Cost ◽  
Chemical Activation ◽  
Nitrogen Adsorption ◽  
Xrd Analysis ◽  
Point Of Zero Charge ◽  
Activation Process ◽  
X Ray ◽  
Tomato Paste

Activated carbons were prepared by carbonization of tomato paste processing industry waste at 500°C followed by chemical activation with KOH, K2CO3, and HCl in N2 atmosphere at low temperature (500°C). The effects of different activating agents and impregnation ratios (25, 50, and 100 wt.%) on the materials’ characteristics were examined. Precursor, carbonized tomato waste (CTW), and activated carbons were characterized by using ultimate and proximate analysis, thermogravimetric analysis (TG/DTG), Fourier transform-infrared (FT-IR) spectroscopy, X-ray fluorescence (XRF) spectroscopy, point of zero charge measurements (pHPZC), particle size analyzer, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) spectroscopy, nitrogen adsorption/desorption isotherms, and X-ray diffraction (XRD) analysis. Activation process improved pore formation and changed activated carbons’ surface characteristics. Activated carbon with the highest surface area (283 m3/g) was prepared by using 50 wt.% KOH as an activator. According to the experimental results, tomato paste waste could be used as an alternative precursor to produce low-cost activated carbon.

Sign in / Sign up

Export Citation Format

Share Document