scholarly journals Movement Laws of Overlying Strata above a Fully Mechanized Coal Mining Face Backfilled with Gangue: A Case Study in Jiulishan Coal Mine in Henan Province, China

2021 ◽  
Vol 2021 ◽  
pp. 1-20
Author(s):  
Zhengkai Yang ◽  
Zhiheng Cheng ◽  
Zhenhua Li ◽  
Chunyuan Li ◽  
Lei Wang ◽  
...  
Keyword(s):  
Coal Mining ◽  
Main Roof ◽  
Surrounding Rock ◽  
Surface Subsidence ◽  
Key Strata ◽  
Key Stratum ◽  
Mining Face ◽  
Failure Depth ◽  
Gangue Backfilling ◽  
Overlying Strata

The aim of this study is to obtain movement laws of overlying strata above a fully mechanized coal mining face backfilled with gangue and solve the problem of surface subsidence during coal mining. This study was carried out based on gangue backfilling mining of Jiulishan Coal Mine (Jiaozuo City, Henan Province, China) from the perspectives of deformation of backfilled gangue under compaction, surrounding rock of a stope, and activities of key strata. The method combining with rock mechanics, viscoelastic mechanics, control theory of rock mass under mining, and numerical simulation was used based on physical and mechanical characteristics of backfilled gangue. On this basis, the research analyzed the temporal-spatial relationships of activities of surrounding rock of the stope, compressive deformation of backfilling body, failure depth of the floor, deformation characteristics of the main roof with laws of surface subsidence. The movement characteristics of overlying strata above the fully mechanized coal mining face backfilled with gangue and the traditional fully mechanized mining face were compared. It is found that, under the same conditions of overlying strata, movement laws of overlying strata are mainly determined by the mining height of coal seams and the heights of a caving zone and a fracture zone are nearly linearly correlated with the mining height. Through analysis based on thin-plate theory and key stratum theory, the location of the main roof of the fully mechanized coal mining face backfilled with gangue in coal seams first bending and sinking due to load of overlying strata was ascertained. Then, it was determined that there are two key strata and the main roof belongs to the inferior key stratum. By using the established mechanical model for the main roof of the fully mechanized coal mining face backfilled with gangue and the calculation formula for the maximum deflection of the main roof, this research presented the conditions for breaking of the main roof. In addition, based on the theoretical analysis, it is concluded that the main roof of the fully mechanized coal mining face backfilled with gangue does not break, but bends. The numerical simulation results demonstrate that, with the continuous increase of strength of backfilled gangue, the stress concentration degree of surrounding rock reduces constantly, so does its decrease amplitude. Moreover, the compressive deformation of backfilling, failure depth of the floor, and bending and subsidence of the main roof continuously decrease and tend to be stable. The mechanical properties of backfilling materials determine effects of gangue backfilling in controlling surface subsidence. Gangue backfilling can effectively control movement of overlying strata and surface subsidence tends to be stable with the increase of elastic modulus of gangue.

scholarly journals Stability Analysis of Roadway Groups under Multi-Mining Disturbances

2021 ◽  
Vol 11 (17) ◽  
pp. 7953
Author(s):  
Yuantian Sun ◽  
Ruiyang Bi ◽  
Qingliang Chang ◽  
Reza Taherdangkoo ◽  
Junfei Zhang ◽  
...  
Keyword(s):  
Coal Mining ◽  
Coal Pillar ◽  
Stability Control ◽  
Surrounding Rock ◽  
Key Strata ◽  
Working Face ◽  
Roadway Stability ◽  
Mining Disturbance ◽  
Mining Face ◽  
The Stability

The roadway stability has been regarded as the main challenging issue for safety and productivity of deep underground coal mines, particularly where roadways are affected by coal mining activities. This study investigates the −740 m main roadway in the Jining No. 2 Coal Mine to provide a theoretical basis for the stability control of the main deep roadway affected by disturbances of adjacent working activities. Field surveys, theoretical analyses, and numerical simulations are used to reveal mechanisms of the coal mining disturbance. The field survey shows that the deformation of roadway increases when the work face advances near the roadway group. Long working face mining causes the key strata to collapse based on the key strata theory and then disturbs the adjacent roadway group. When the working face is 100 m away from the stop-mining line, the roadway group is affected by the mining face, and the width roadway protection coal pillar is determined to be about 100 m. Flac3D simulations prove the accuracy of the theoretical result. Through reinforcement and support measures for the main roadway, the overall strength of the surrounding rock is enhanced, the stability of the surrounding rock of the roadway is guaranteed, and the safe production of the mine is maintained.

New Technology of Surface Subsidence Control and Environmental Protection Research in Coal Mining Region

2014 ◽  
Vol 675-677 ◽  
pp. 1385-1394
Author(s):  
Cheng Rong Jiang ◽  
Liu Yang ◽  
Hao Xie ◽  
Hua Yi Huang ◽  
De Ke Sun
Keyword(s):  
Coal Mining ◽  
New Technology ◽  
Mining Area ◽  
Industrial Test ◽  
Surface Subsidence ◽  
High Concentration ◽  
Geological Conditions ◽  
Surface Subsidence Control ◽  
Fissure Water ◽  
Overlying Strata

In combination with the geological conditions of Tie'er mining area in Tangshan coal mining, this paper not only analyzes the evolution of overlying strata structure in stope and the development law of overlying strata separation, also proposes a new continuous grouting technology with large flow and high concentration slurry. The industrial test showed that, when the grout-mining ratio of the whole mining area is 25.3%, the reducing subsidence ratio is 51.5%, the effect of reducing the surface subsidence is good. According to the chemical analysis of water quality ingredients of slurry, the test result showed, heavy metals contents in fly-ash slurry water do not exceed the standard, which has no bad effect on the fissure water in the bedrock.

scholarly journals Study on the Law of Surface Cracks While Coal Mining in the Thin Bedrock and Thick Unconsolidated Layer of Yu-Shen-Fu Mining Area

2018 ◽  
Vol 53 ◽  
pp. 03040
Author(s):  
Wu Zuoqi ◽  
Wang Guoku ◽  
Zhao Liqin
Keyword(s):  
Coal Mining ◽  
Ground Surface ◽  
Mining Area ◽  
Dynamic Evolution ◽  
Surface Cracks ◽  
Whole Process ◽  
Thin Bedrock ◽  
The Law ◽  
Mining Face ◽  
Overlying Strata

The law of surface cracks caused by coal mining in ther thin bedrock and thick unconsolidated layer was studied in Yu-Shen-Fu mining area. The crack development in the overlying strata of the coal mining face was detected by drilling survey technology, the whole process of the ground surface crack dynamic evolution was carried out by similar material simulation, and the law of surface cracks evolution was verified by on-site tracking measurement. The study reached the regulation of the overlying strata failure and dynamic evolution of surface cracks caused by coal mining under thin bedrock and thick unconsolidated layer in Yu-Shen-Fu mining area, which can provide theoretical support for the ecological restoration of western mining area.

scholarly journals Deformation Rules for Surrounding Rock in Directional Weakening of End Roofs of Thin Bedrocks and Ultrathick Seams

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Fei Liu ◽  
Zhanguo Ma ◽  
Yongsheng Han ◽  
Zhimin Huang
Keyword(s):  
Abutment Pressure ◽  
Main Roof ◽  
Stability Control ◽  
Surrounding Rock ◽  
Western China ◽  
Resource Exploitation ◽  
Failure Characteristics ◽  
Key Strata ◽  
Working Face ◽  
Geological Conditions

With the deployment of China’s energy strategy in the western regions, complex geological mining conditions such as thin bedrock and ultrathick seams in western China have caused a series of problems such as serious deformation of the surrounding rock at the ends of the working face and the increase in the lead abutment pressure of the roadways; the research on end roof deformation in the resource exploitation in western China has become one of the great demands of the industry. Based on the failure characteristics of rock mass, relying on the actual mining geological conditions of a coal mine in Inner Mongolia, the failure characteristics of the overlying rock strata under the influence of mining were simulated and analyzed using similar material simulation experiment, which intuitively reproduced the failure and deformation processes of the immediate roof, main roof, and key strata and revealed the mechanical mechanism of the directional weakening of the end roof. It is of great significance for the stability control of the surrounding rock at the end of the fully mechanized caving face in the thin bedrocks and ultrathick seams, reducing the abutment pressure of gate roadway and controlling the spontaneous combustion of residual coal in the goaf.

scholarly journals The Key Stratum Structure Morphology of Longwall Mechanized Top Coal Caving Mining in Extra-Thick Coal Seams: A Typical Case Study

2020 ◽  
Vol 2020 ◽  
pp. 1-13 ◽  
Author(s):  
Fulian He ◽  
Xiaobin Li ◽  
Wenrui He ◽  
Yongqiang Zhao ◽  
Zhuhe Xu ◽  
...  
Keyword(s):  
Coal Seam ◽  
Cantilever Beam ◽  
Coal Seams ◽  
Key Strata ◽  
Key Stratum ◽  
Structure Morphology ◽  
Coal Wall ◽  
Coal Seam Thickness ◽  
Longitudinal Cracks ◽  
Overlying Strata

Longwall mechanized top coal caving mining (LMTCCM) in extra-thick coal seams has its own characteristics. The law of mining pressure and overlying strata failure height in extra-thick coal seams are much larger than those of medium-thick and thick coal seams. The key stratum structure morphology also has an important influence on the law of overlying strata movement and stability of surrounding rock. Based on the engineering geological conditions, this paper used the method of theoretical analysis and numerical simulation to study the key stratum structure morphology of LMTCCM in extra-thick coal seams. The results show that under the condition of LMTCCM in extra-thick coal seams, the key stratum forms the structure of low cantilever beam and high hinged rock beam. With the increase of coal seam thickness, the breaking position of cantilever beam is closer to the coal wall. Through theoretical calculation, it is obtained that the breaking length of cantilever beam is 31.5 m and the breaking position of cantilever beam is 15.4 m away from coal wall. With the increase of cycle, key strata will undergo the evolution law from the generation of longitudinal cracks to the hinged structure and then to the cantilever beam structure. The breakage of key strata will cause the expansion of longitudinal cracks and the overall synchronous movement of overlying strata. With the increase of coal seam thickness, the distribution of longitudinal cracks will gradually transfer from the upper part of goaf to the deep part of coal body in space and increase in quantity. This research is of great significance for improving the stability of overlying strata and ensuring the safe and efficient mining of extra-thick coal seams.

scholarly journals The Study of Key Stratum Location and Characteristics on the Mining of Extremely Thick Coal Seam under Goaf

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Gaochuan Guo ◽  
Yongkang Yang
Keyword(s):  
Coal Seam ◽  
Longwall Mining ◽  
Maximum Principal Stress ◽  
Engineering Practice ◽  
Coal Seams ◽  
Thick Coal Seam ◽  
Key Strata ◽  
Key Stratum ◽  
Arch Structure ◽  
Overlying Strata

The basis of traditional ground pressure and strata control techniques is the key strata theory, wherein the position of the key stratum can easily be determined for coal seams with regular thickness and without goaf. However, in the case of mining ultrathick coal seams underneath goaf, the traditional methods used for the calculation of key stratum position need to be improved in order to account for the additional coal seam thickness and the presence of an upper goaf. This study analyzed the failure height and collapse characteristics of overlying strata during excavation for determining the structure of the failed overlying strata. The results indicate that the intercalation and overlying strata gradually evolve into a large “arch structure” and a small “arch structure” during longwall mining, respectively. A mechanical model of the bearing characteristics of the interlayer key strata structure was established according to the structure of the intercalation rock layer, which is a hinged block structure. The results of the model indicate that the maximum principal stress occurs when the key strata portion of the arch structure bears the overlying load. Consequently, the movement and position of the interlayer key strata can be evaluated throughout the mining process of the ultrathick coal seams underneath goaf. This method was used to determine the position of interlayer key stratum of overlying strata in Xiegou coal mine. And the results agree with that of the engineering practice. The results are significant to determine the key strata position during ultrathick coal seam underneath goaf longwall mining.

scholarly journals Multidirectional Anisotropic Total Variation and Its Application in the Tomography of the Surrounding Rock of Coal Mining Faces

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Bo Chen ◽  
Guowei Zhu ◽  
Zhenqiang Yang
Keyword(s):  
Coal Mining ◽  
Total Variation ◽  
Regularization Method ◽  
Surrounding Rock ◽  
Total Variation Regularization ◽  
Ct Reconstruction ◽  
Traveltime Tomography ◽  
Transmitted Waves ◽  
Mining Face ◽  
Anisotropic Total Variation

The computed tomography (CT) reconstruction algorithm is one of the crucial components of the CT system. To date, total variation (TV) has been widely used in CT reconstruction algorithms. Although TV utilizes the a priori information of the longitudinal and lateral gradient sparsity of an image, it introduces some staircase artifacts. To overcome the current limitations of TV and improve imaging quality, we propose a multidirectional anisotropic total variation (MATV) that uses multidirectional gradient information. The surrounding rock of coal mining faces uses principles of tomography similar to those of medical X-rays. The velocity distribution for the surrounding rock can be obtained by the first-arrival traveltime tomography of the transmitted waves in the coal mining face. Combined with the geological data, we can interpret the geological hazards in the coal mining face. To perform traveltime tomography, we first established the objective function of the first-arrival traveltime tomography of the transmitted waves based on the MATV regularization and then used the split Bregman method to solve the objective function. The simulated data and real data show that the MATV regularization method proposed in this paper can better maintain the boundaries of geological anomalies and reduce the artifacts compared with the isotropic total variation regularization method and the anisotropic total variation regularization method. Furthermore, this approach describes the distribution of geological anomalies more accurately and effectively and improves imaging accuracy.

Research on Supporting Technology of Roadway Driving along Next Goaf of Second Mining Strip Pillar

2012 ◽  
Vol 446-449 ◽  
pp. 1657-1660
Author(s):  
Wei Dong Lv ◽  
Nan Nan Zhao
Keyword(s):  
Abutment Pressure ◽  
High Strength ◽  
Main Roof ◽  
Surrounding Rock ◽  
Control Effect ◽  
General Stability ◽  
High Strength Bolt ◽  
Mining Face ◽  
The Stability ◽  
Surrounding Rock Deformation

For roadway driving along next goaf of strip pillar second mining, being influenced by the abutment pressure of previous coal mining face and main roof breaking rotary deformation, the surrounding rock deformation is serious and the control effect of ordinary bolt supporting on the general stability of roadway driving along next goaf is poorer. According to the concrete geological and technique condition of the 2351 second mining strip pillar in Daizhuang Colliery, adopting the united support pattern combined high strength bolt of levorotatory continuous thread and anchor of low relaxation prestress, the safety of the roadway can be ensured and the stability of the roadway surrounding rocks can be improved. It is of significant reference meaning for bolting support of roadway driving along next goaf of second mining strip pillar under similar condition.

Stress Shell Mechanical Mechanism of Fully-Mechanized Face Enhancing the Upper Limit for Coal Mining and Risk Analysis of Support Break-Off

2012 ◽  
Vol 524-527 ◽  
pp. 466-470
Author(s):  
Jun Ling Hou ◽  
Yan Sun
Keyword(s):  
Stress Distribution ◽  
Coal Seam ◽  
Coal Mining ◽  
Surrounding Rock ◽  
Mechanical Environment ◽  
Upper Limit ◽  
Working Face ◽  
Distribution Rule ◽  
Geological Conditions ◽  
Mining Face

Based on the geological conditions and specific mining technology conditions of the 11014 mining face of Panbei mine in HuaiNan mining group ,using the FLAC3D software, simulate the stress distribution rule and disruption field distribution rule of surrounding rock of Fully-Mechanized face enhancing the upper limit for coal mining along the tendency and trend of coal seam by different mining speed of 6 m/d, 4 m/d and 2 m/d. draw the conclusion that enhancing the mining speed can alleviate the pressure of the working face ,improve the working face mechanical environment,and reduce the extent of the failure field.It provides the theory basis and reference for Fully-Mechanized face enhancing the upper limit for coal mining under similar conditions.

Laws of Formation and Evolution of Pressure Arch in Coal Mining Adjoining Rock

2011 ◽  
Vol 243-249 ◽  
pp. 2596-2600
Author(s):  
Xiao Li Du ◽  
Hong Wei Song ◽  
Jie Chen
Keyword(s):  
Numerical Simulation ◽  
Coal Mining ◽  
Vertical Direction ◽  
Stress Transfer ◽  
Surrounding Rock ◽  
Coefficient Variation ◽  
Working Face ◽  
Formation And Evolution ◽  
Mining Face ◽  
Adjoining Rock

Based on numerical simulation of computing Software ANSYS, the curve of arching coefficient variation of pressure arch due to actual mining was analyzed aiming to a special mining face, the law of stress transfer and change in surrounding rock was discussed, and the evolving features and characteristics of pressure arch was obtained. The analysis and discussion show the following facts: Arch body will become thicker and stress in the arch body increases with working face’s driving distance increasing; the morphology of pressure arch transits from ellipsoid with long axis in the vertical direction to ellipsoid with long axis in the horizontal direction along the trend of working face; along the tendency of working face, the morphology of pressure arch is a ellipsoid with long axis in the vertical direction.

Sign in / Sign up

Export Citation Format

Share Document