New Approaches To the Design of Active Filters

SIMULATION ◽  
1966 ◽  
Vol 6 (5) ◽  
pp. 323-336 ◽  
Author(s):  
Peter D. Hansen
Keyword(s):  
High Performance ◽  
Impedance Matching ◽  
Analog Computer ◽  
Active Filters ◽  
Pass Band ◽  
Design Data ◽  
Low Pass ◽  
Band Pass ◽  
Low Pass Filters ◽  
High Pass

Operational amplifiers can greatly simplify the design of high performance signal filters because they elimi nate the need for inductors and for impedance matching. Furthermore, use of active filters can result in reduc tion of weight, size, and cost. Filters designed to satisfy sophisticated mathematical criteria can be realized without resort to "equalization" or trimming. In this issue we discuss the design of operational amplifier and analog computer circuits suitable for use as low pass filters. We also discuss the commonly used mathematically designed filters, i.e. Butterworth, Chebyshev, and Bessel. In addition, we present two new types of theoretical filters, the Paynter and the Aver aging filters. Design data necessary for realizing these theoretical filters with amplifier circuits is provided. In the next issue we shall discuss the design of band pass, band reject, high pass and all pass active filter circuits.

CURRENT-MODE ACTIVE-C FILTER EMPLOYING REDUCED NUMBER OF CCCII+s

2007 ◽  
Vol 16 (04) ◽  
pp. 507-516 ◽  
Author(s):  
SHAHRAM MINAEI ◽  
ERKAN YUCE
Keyword(s):  
Current Mode ◽  
Pass Band ◽  
Passive Component ◽  
Resistorless Filter ◽  
Low Pass ◽  
Component Matching ◽  
Band Pass ◽  
High Output Impedance ◽  
Quality Factor Q ◽  
High Pass

In this paper, a universal current-mode second-order active-C filter for simultaneously realizing low-pass, band-pass and high-pass responses is proposed. The presented filter employs only three plus-type second-generation current-controlled conveyors (CCCII+s). This filter needs no critical active and passive component matching conditions and no additional active and passive elements for realizing high output impedance low-pass, band-pass and high-pass characteristics. The angular resonance frequency (ω0) and quality factor (Q) of the proposed resistorless filter can be tuned electronically. To verify the theoretical analysis and to exhibit the performance of the proposed filter, it is simulated with SPICE program.

NOVEL VOLTAGE-MODE UNIVERSAL FILTER USING ONLY TWO CDBAs

2005 ◽  
Vol 14 (01) ◽  
pp. 159-164 ◽  
Author(s):  
SUDHANSHU MAHESHWARI ◽  
IQBAL A. KHAN
Keyword(s):  
Pass Band ◽  
Universal Filter ◽  
Input Selection ◽  
Voltage Mode ◽  
Single Output ◽  
Control Computer ◽  
Low Pass ◽  
Band Pass ◽  
Pass Through ◽  
High Pass

A novel voltage-mode universal filter employing only two current differencing buffered amplifiers (CDBAs) is proposed. The filter uses four inputs and single output to realize six responses, viz. low-pass, high-pass, inverting band-pass, noninverting band-pass, band-elimination, and all-pass through input selection with independent pole-Q control. Computer simulation results using SPICE are also given to verify the theory.

scholarly journals Design and Implementation of Digital Filters for ECG Data Based on Field Programmable Gate Array and MATLAB

2020 ◽  
pp. 17-19
Author(s):  
Emre Cancioglu ◽  
Gokberk Cakiroglu ◽  
Alkim Gokcen ◽  
Yilmaz Sefa Altanay
Keyword(s):  
Digital Filters ◽  
Pass Band ◽  
System Generator ◽  
Design And Implementation ◽  
Field Programmable ◽  
Low Pass ◽  
Band Pass ◽  
Database Platform ◽  
High Pass ◽  
Ecg Data

This study provides design and implementation of four digital filters (low pass, high pass, band pass and band stop) for ECG (electrocardiogram) data on FPGA with MATLAB by a serial communication. The study is conducted with using ECG data which is obtained from PhysioBank Database platform. SysGen (System Generator for DSP) which is a toolbox for MATLAB is used for designing and implementing the digital filters. The aim of the study is to perform four different digital filters with various blocks on the SysGen Toolbox. The study then examines the results of four different digital filters.

A New Tunable SISO Filter Designed in 40nm CMOS for Bilateral Inverse and Buffer Filtering Applications

2021 ◽  
pp. 2150240
Author(s):  
Umar Mohammad ◽  
Fang Tang ◽  
Shu Zhou ◽  
Mohd Yusuf Yasin
Keyword(s):  
Simulation Analysis ◽  
Pass Band ◽  
Single Input Single Output ◽  
Change Of Direction ◽  
Single Output ◽  
Low Pass ◽  
Single Input ◽  
Band Pass ◽  
Parasitic Components ◽  
High Pass

A new study imitating the design and implementation of single-input–single-output (SISO) filters as bilateral filters has been presented in this paper. Second generation current controlled current conveyor (CCCII), being a popular low power active element was considered for the realization of the proposed design. Complete design, analysis and implementation of the voltage mode SISO filter was done using only two CCCII’s and two passive parasitic components. The striking feature of this work is that the proposed design can be made to work at either the input node or the output node, as well as in the cases; the change of direction changes the filter into an inverse filter and buffer filter. Basic filter applications like low-pass, high-pass, band-pass and band-stop were aimed to check the uniformity of the proposed design at different frequencies. Results perceived from the simulation study were fare enough on both the side nodes of the proposed design. Categorically, the circuit can be aimed to work in lieu of a filter transceiver. The consistency of the circuit was analyzed by the nodal analysis. Whereas the working performance was enormously analyzed and evaluated during the simulation analysis. The proposed design was simulated in HSPICE tool to exhibit and exploit the delivery, using the 45[Formula: see text]nm predictive technology model (PTM) parameters, with [Formula: see text][Formula: see text]V rail to rail voltages. Maximum power consumption of the circuit is around 138.5[Formula: see text][Formula: see text]W. Finally, the design was also implemented in Cadence Virtuoso using 40[Formula: see text]nm SMIC parameters.

Second-Order Voltage-Mode Universal Filters Using Two DVCCs, Two Grounded Capacitors and Four Resistors

2016 ◽  
Vol 25 (12) ◽  
pp. 1650154 ◽  
Author(s):  
Ahmet Abaci ◽  
Erkan Yuce
Keyword(s):  
Integrated Circuit ◽  
Matching Condition ◽  
Second Order ◽  
Point Of View ◽  
Pass Band ◽  
Current Conveyors ◽  
Voltage Mode ◽  
Low Pass ◽  
Band Pass ◽  
High Pass

In this paper, two new second-order voltage-mode universal filters are proposed. Both of the proposed filters use only two differential voltage current conveyors (DVCCs), four resistors and two grounded capacitors which are advantageous from integrated circuit technology point of view. They can simultaneously provide second-order low-pass, high-pass, band-pass, notch and all-pass responses. They offer orthogonal control of angular resonance frequency and quality factor. However, they have a single matching condition for only all-pass responses. A number of simulations based on SPICE program are accomplished in order to demonstrate the performance of both filters.

A NEW ELECTRONICALLY-TUNABLE ACTIVE-ONLY UNIVERSAL BIQUAD

2011 ◽  
Vol 20 (03) ◽  
pp. 549-555 ◽  
Author(s):  
A. K. SINGH ◽  
R. SENANI ◽  
D. R. BHASKAR ◽  
R. K. SHARMA
Keyword(s):  
Pass Band ◽  
Voltage Mode ◽  
Op Amp ◽  
Op Amps ◽  
Reasonable Number ◽  
Low Pass ◽  
Band Pass ◽  
Electronically Tunable ◽  
High Pass ◽  
Realization Condition

A number of configurations for realizing voltage-mode (VM) biquads using op-amps and OTAs have been presented in the literature, however, none of these provide the following desirable properties simultaneously: (i) realizability of all the five standard filters (namely; low pass, high pass, band pass, band stop and all pass), (ii) tunability of all the three filter parameters (namely; ω0, bandwidth or Q0 and gain) and (iii) not requiring any realization condition in any of the five filter responses. This paper presents a new configuration which does possess all the above mentioned desirable properties simultaneously while using only two internally-compensated type op-amps and a reasonable number of OTAs. The workability of the new configuration has been demonstrated by SPICE simulations based upon CMOS Op-amp and CMOS OTAs.

scholarly journals Glass Patterns: Some Contrast Effects Re-Evaluated

Perception ◽  
1997 ◽  
Vol 26 (3) ◽  
pp. 253-268 ◽  
Author(s):  
Steven C Dakin
Keyword(s):  
Spatial Filtering ◽  
Contrast Effects ◽  
Visual Grouping ◽  
Relative Contrast ◽  
Low Pass ◽  
Band Pass ◽  
Opposite Contrast ◽  
Low Pass Filters ◽  
Glass Patterns ◽  
High Pass

The relative contrast of features is known to be important in determining if they can be grouped. Two manipulations of feature contrast have previously been used to criticise models of visual grouping based on spatial filtering: high-pass filtering and reversal of contrast polarity. The effects of these manipulations are considered in the context of the perception of Glass patterns. It is shown that high-pass filtering elements, whilst destroying structure in the output of low-pass filters, do not significantly disrupt the output of locally band-pass filters. The finding that subjects can perceive structure in Glass patterns composed of high-pass features therefore offers no evidence against such spatial filtering mechanisms. Band-pass filtering models are shown to explain the rotation of perceived structure in Glass patterns composed of opposite contrast features. However, structure is correctly perceived in patterns composed of two ‘interleaved’ opposite contrast patterns, which is problematic for oriented filtering mechanisms. Two possible explanations are considered: nonlinear contrast transduction prior to filtering, and integration of local orientation estimates from first-order and second-order mechanisms.

FIRST-ORDER FILTERS GENERALIZED TO THE FRACTIONAL DOMAIN

2008 ◽  
Vol 17 (01) ◽  
pp. 55-66 ◽  
Author(s):  
A. G. RADWAN ◽  
A. M. SOLIMAN ◽  
A. S. ELWAKIL
Keyword(s):  
Fractional Order ◽  
Pass Band ◽  
Integer Order ◽  
Continuous Time Filters ◽  
Passive Filters ◽  
Low Pass ◽  
Band Pass ◽  
Half Power ◽  
The Right ◽  
High Pass

Traditional continuous-time filters are of integer order. However, using fractional calculus, filters may also be represented by the more general fractional-order differential equations in which case integer-order filters are only a tight subset of fractional-order filters. In this work, we show that low-pass, high-pass, band-pass, and all-pass filters can be realized with circuits incorporating a single fractance device. We derive expressions for the pole frequencies, the quality factor, the right-phase frequencies, and the half-power frequencies. Examples of fractional passive filters supported by numerical and PSpice simulations are given.

Programmable Universal Filters Using Current Conveyor Transconductance Amplifiers

2017 ◽  
Vol 26 (07) ◽  
pp. 1750121 ◽  
Author(s):  
Thanat Nonthaputha ◽  
Montree Kumngern
Keyword(s):  
Transfer Functions ◽  
Current Mode ◽  
Current Conveyor ◽  
Pass Band ◽  
Cmos Process ◽  
Low Pass ◽  
Band Pass ◽  
Transconductance Amplifiers ◽  
Biquadratic Filters ◽  
High Pass

This paper presents new programmable universal biquadratic filters using current conveyor transconductance amplifiers (CCTAs) by which both voltage- and current-mode filters can be obtained. The proposed filters use second-generation current conveyor (CCII) which is the first stage of CCTA to operate as current conveyor analog switch (CCAS) and this CCAS will be used to program the filtering functions such as low-pass, high-pass, band-pass, band-stop and all-pass filters. Unlike previous universal filters, the filtering functions of the proposed filters can be programmed using the bias currents of CCTAs without changing any input and output connections. The natural frequency and quality factor of all filtering functions can be controlled electronically and orthogonally using the bias currents of transconductance amplifiers. Also gain response of all transfer functions can be adjusted. The active and passive sensitivities of the filters are low. The proposed programmable filters have been simulated using 0.18[Formula: see text][Formula: see text]m CMOS process from TSMC. PSPICE simulation results are included to confirm workability of the proposed circuits.

CDTAs Based Current-Mode Universal Biquad Filters with Orthogonal Control of Quality Factor and Pole Frequency

2013 ◽  
Vol 787 ◽  
pp. 501-507
Author(s):  
Saksit Summart ◽  
Chanchai Thongsopa
Keyword(s):  
Quality Factor ◽  
Integrated Circuit ◽  
Current Mode ◽  
Pass Band ◽  
Cascade Connection ◽  
Low Pass ◽  
Band Pass ◽  
High Output Impedance ◽  
Further Development ◽  
High Pass

This article presents current-mode universal biquad filters based on CDTAs. The filter circuits using four CDTAs and two grounded capacitors which are able to provide low-pass, high-pass, band-pass, band-reject and all-pass functions. The pole frequency can be orthogonally controlled from quality factor and the circuits have high output impedance appropriate for cascade connection application in current mode which is capable to directly drive load. This qualification is very appropriate for further development into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.

Sign in / Sign up

Export Citation Format

Share Document