Effects of polymer blend composition on membrane properties and separation performance of PEES/PEI blend membrane

2016 ◽  
Vol 29 (4) ◽  
pp. 467-475 ◽  
Author(s):  
R Saranya ◽  
JS Beril ◽  
D Mohan
Keyword(s):  
Thermal Stability ◽  
Contact Angle ◽  
Protein Separation ◽  
Pure Water ◽  
Water Flux ◽  
Membrane Properties ◽  
Separation Performance ◽  
Blend Membrane ◽  
Blend Membranes ◽  
Protein Rejection

In this work, an attempt has been made for protein rejection from aqueous solution using ultrafiltration blend membrane based on poly(phenylene ether ether sulfone) (PEES) and polyetherimide (PEI) was prepared in various blend compositions. Prepared membranes were characterized in terms of pure water flux, water content, membrane hydraulic resistance, porosity, contact angle, scanning electron microscopy, thermogravimetric analysis, and attenuated total reflectance-Fourier transform infrared spectroscopy. Studies were carried out to find out the rejection of proteins such as trypsin, pepsin, egg albumin, and bovine serum albumin. The extent of protein separation is directly proportional to molecular weight of protein. Pristine PEES membrane exhibited high-percentage protein rejection of BSA (92.7%), EA (88.2%), pepsin (85.8%), and trypsin (82.2%) compared to PEES/PEI blend membranes. PEES/PEI blend membranes have better hydrophilic property compared to pristine PEES membrane. Pristine PEES has a contact angle of 97.8°, embedded with PEI and reduced to 67.9°. The thermal stability of the membrane was slightly decreased when the percentage of PEI composition into the PEES/PEI blend increased and observed that the pure PEES membrane has superior thermal stability than PEES/PEI blend membranes

scholarly journals Removal of Dye from a Leather Tanning Factory by Flat-Sheet Blend Ultrafiltration (UF) Membrane

Membranes ◽  
2020 ◽  
Vol 10 (3) ◽  
pp. 47 ◽  
Author(s):  
Maryam Y. Ghadhban ◽  
Hasan Shaker Majdi ◽  
Khalid T. Rashid ◽  
Qusay F. Alsalhy ◽  
D. Shanthana Lakshmi ◽  
...  
Keyword(s):  
Contact Angle ◽  
Pure Water ◽  
Composite Membranes ◽  
Membrane Properties ◽  
Inversion Method ◽  
Average Roughness ◽  
Structural Formation ◽  
Blend Membrane ◽  
Flat Sheet ◽  
Pes Membrane

In this work, a flat-sheet blend membrane was fabricated by a traditional phase inversion method, using the polymer blends poly phenyl sulfone (PPSU) and polyether sulfone (PES) for the ultrafiltration (UF) application. It was hypothesized that adding PES to the PPSU polymer blend would improve the properties of the PPSU membrane. The effect of the PES concentration on the blend membrane properties was investigated extensively. The characteristics of PPSU-PES blend membranes were investigated using atomic force microscopy (AFM), scanning electron microscopy (SEM), contact angle measure, and contaminant (dye) elimination efficiency. This study showed that PES clearly affected the structural formation of the blended membranes. A considerable increase in the average roughness (about 93%) was observed with the addition of 4% PES, with a higher mean pore size accompanied by a rise in the pores’ density on the surface of the membrane. The addition of up to 4% PES had a significant influence on the hydrophilic character of the PPSU-PES membrane, by lowering the value of the contact angle (CA) (i.e., to 56.9°). The performance of the PPSU-PES composite membranes’ UF performance was systematically investigated, and the membrane pure water permeability (PWP) was enhanced by 25% with the addition of 4% PES. The best separation removal factor achieved in the current investigation for dye (Drupel Black NT) was 96.62% for a PPSU-PES (16:4 wt./wt.%) membrane with a 50% feed dye concentration.

Hydrophilicity Effect of Rice Husk Silica on Mixed Matrix PSF Membrane Properties

2014 ◽  
Vol 70 (2) ◽  
Author(s):  
Zawati Harun ◽  
Muhamad Fikri Shohur ◽  
Mohd Riduan Jamalludin ◽  
Muhamad Zaini Yunos ◽  
Hatijah Basri
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Rice Husk ◽  
Pure Water ◽  
Water Flux ◽  
Membrane Properties ◽  
Mixed Matrix Membrane ◽  
Mixed Matrix ◽  
Rice Husk Silica ◽  
Phase Inversion Technique

The effects of two types of additives rice husk silica (RHS) towards membrane hydrophilicity and flux performance were investigated. Different percentages or concentrations of rice husk silica (RHS) additive were used to form a mixed matrix membrane. This flat sheet mixed matrix membrane was prepared via phase inversion technique. The fabricated membrane was characterized by contact angle and surface roughness measurements, whereas the flux permeation was measured using pure water flux. The result demonstrated that the addition both types of rice husk silica have increased the hydrophilicity properties of the mixed matrix membrane. Stronger effect of hydrophilicity is shown upon addition of amorphous rice husk particle where both contact angle and surface roughness were reduced and increased, respectively.   

Hydrophilically Modified Poly(vinylidene fluoride) Membrane for Removal of Methylene Blue Dye

2020 ◽  
Vol 17 (2) ◽  
pp. 1499-1502
Author(s):  
J. Hamdan ◽  
H. Hasbullah ◽  
M. N. M. Sokri ◽  
N. S. M. Sabri ◽  
M. A. F. Suran ◽  
...  
Keyword(s):  
Methylene Blue ◽  
Contact Angle ◽  
Polyvinylidene Fluoride ◽  
Pure Water ◽  
Water Flux ◽  
Blue Dye ◽  
Separation Performance ◽  
Methylene Blue Dye ◽  
Pvdf Membrane ◽  
Pure Water Flux

Polyvinylidene Fluoride (PVDF) has been used as a membrane’s base material for wastewater treatment for quite some time. Due to PVDF hydrophobic nature, fouling will occur, thus, reducing the membrane performance. The main objective of this study was to investigate the effect of various chitosan loadings on membrane hydrophilicity and overall liquid separation performance. The loadings of chitosan (wt.%) used were neat PVDF, 0.25%, 0.5%, 0.75% and 1% in PVDF mixed matrix membrane. It was found that 0.75% chitosan membrane had the lowest contact angle of 63° making it the most hydrophilic. The pure water flux test on the membranes also showed the same trend where the lowest contact angle resulting in the highest pure water flux. The PVDF membrane containing 0.75% chitosan possessed the highest pure water flux of 43.5 Lm−2h−1. With the rejection of dye of over 43.12%. The study proved that adding chitosan into PVDF membrane certainly improved the membrane hydrophilicity and the percentage removal of methylene blue dye.

Influence of Hydrophilic Polymer on Pure Water Permeation, Permeability Coefficient, and Porosity of Polysulfone Blend Membranes

2014 ◽  
Vol 931-932 ◽  
pp. 168-172 ◽  
Author(s):  
Asmadi Ali ◽  
Mohamad Awang ◽  
Ramli Mat ◽  
Anwar Johari ◽  
Mohd Johari Kamaruddin ◽  
...  
Keyword(s):  
Permeability Coefficient ◽  
Pure Water ◽  
Polymer Concentration ◽  
Water Flux ◽  
Hydrophilic Polymer ◽  
Hydrophobic Property ◽  
Water Permeation ◽  
Blend Membranes ◽  
Wet Phase Inversion ◽  
Pure Water Flux

It is well known that membrane with hydrophobic property is a fouling membrane. Polysulfone (PSf) membrane has hydrophobic characteristic was blended with a hydrophilic polymer, cellulose acetate phthalate (CAP) in order to increase hydrophilicity property of pure PSf membrane. In this study, membrane casting solutions containing 17 wt% of polymer was prepared via wet phase inversion process. The pure PSf membrane was coded as PC-0. PSf/CAP blend membranes with blend composition of 95/5, 90/10, 85/15 and 80/20 wt% of total polymer concentration in the membrane casting solutions were marked as PC-5, PC-10, PC-15 and PC-20 respectively. All of the membranes were characterized in terms of pure water flux and permeability coefficient in order to study their hydrophilicity properties. The investigated results shows that increased of CAP composition in PSf blend membranes has increased pure water flux, permeability coefficient and porosity of the blend membrane which in turn formed membrane with anti-fouling property.

scholarly journals The Modification of PVDF Membrane via Crosslinking with Chitosan and Glutaraldehyde as the Crosslinking Agent

2018 ◽  
Vol 18 (1) ◽  
pp. 1
Author(s):  
Romaya Sitha Silitonga ◽  
Nurul Widiastuti ◽  
Juhana Jaafar ◽  
Ahmad Fauzi Ismail ◽  
Muhammad Nidzhom Zainol Abidin ◽  
...  
Keyword(s):  
Contact Angle ◽  
Vinylidene Fluoride ◽  
Membrane Surface ◽  
Pure Water ◽  
Water Flux ◽  
Crosslinking Agent ◽  
Hydrophobic Properties ◽  
Pvdf Membrane ◽  
Pure Water Flux ◽  
Modified Membrane

Poly(vinylidene fluoride) (PVDF) has outstanding properties such as high thermal stability, resistance to acid solvents and good mechanical strength. Due to its properties, PVDF is widely used as a membrane matrix. However, PVDF membrane is hydrophobic properties, so as for specific applications, the surface of membrane needs to be modified to become hydrophilic. This research aims to modify PVDF membrane surface with chitosan and glutaraldehyde as a crosslinker agent. The FTIR spectra showed that the modified membrane has a peak at 1655 cm-1, indicating the imine group (–N=C)- that was formed due to the crosslink between amine group from chitosan and aldehyde group from glutaraldehyde. Results showed that the contact angle of the modified membrane decreases to 77.22° indicated that the membrane hydrophilic properties (< 90°) were enhanced. Prior to the modification, the contact angle of the PVDF membrane was 90.24°, which shows hydrophobic properties (> 90°). The results of porosity, Ɛ (%) for unmodified PVDF membrane was 55.39%, while the modified PVDF membrane has a porosity of 81.99%. Similarly, by modifying the PVDF membrane, pure water flux increased from 0.9867 L/m2h to 1.1253 L/m2h. The enhancement of porosity and pure water flux for the modified PVDF membrane was due to the improved surface hydrophilicity of PVDF membrane.

scholarly journals Preparation and Characterization of MWCNTs/PVDF Conductive Membrane with Cross-Linked Polymer PVA and Study on Its Anti-Fouling Performance

Membranes ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 703
Author(s):  
Yi Ding ◽  
Zhansheng Guo ◽  
Xinan Dong ◽  
Hong You ◽  
Junxue Mei ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Mass Loss Rate ◽  
Pure Water ◽  
Water Flux ◽  
Membrane Properties ◽  
Elongation Ratio ◽  
Functional Layer ◽  
Conductive Membranes ◽  
Pure Water Flux ◽  
Conductive Membrane

Based on carboxylated multi-walled carbon nanotubes (MWCNTs-COOH), a MWCNTs/PVDF conductive membrane was prepared by a vacuum filtration cross-linking method. The surface compositions and morphology of conductive membranes were studied by X-ray photoelectron spectroscopy and high-resolution field emission scanning electron microscopy, respectively. The effects of cross-linked polymeric polyvinyl alcohol (PVA) on the conductive membrane properties such as the porosity, pore size distribution, pure water flux, conductivity, hydrophilicity, stability and antifouling properties were investigated. Results showed that the addition of PVA to the MWCNTs/PVDF conductive membrane decreased the pure water flux, porosity and the conductivity. However, the hydrophilicity of the modified MWCNTs/PVDF conductive membrane was greatly improved, and the contact angle of pure water was reduced from 70.18° to 25.48° with the addition of PVA contents from 0 wt% to 0.05 wt%. Meanwhile, the conductive membranes with higher content had a relatively higher stability. It was found that the conductive functional layer of the conductive membrane had an average mass loss rate of 1.22% in the 30 min ultrasonic oscillation experiment. The tensile intensity and break elongation ratio of the conductive membrane are improved by the addition of PVA, and the durability of the conductive membrane with PVA was superior to that without PVA added. The electric assisted anti-fouling experiments of modified conductive membrane indicated that compared with the condition without electric field, the average flux attenuation of the conductive membrane was reduced by 11.2%, and the membrane flux recovery rate reached 97.05%. Moreover, the addition of PVA could accelerate the clean of the conductive membranes.

IMPACTS OF HYDROPHILIC NANOFILLERS ON SEPARATION PERFORMANCE OF THIN FILM NANOCOMPOSITE REVERSE OSMOSIS MEMBRANE

2016 ◽  
Vol 78 (12) ◽  
Author(s):  
C. Y. Chong ◽  
G. S. Lai ◽  
W. J. Lau ◽  
N. Yusof ◽  
P. S. Goh ◽  
...  
Keyword(s):  
Thin Film ◽  
Water Permeability ◽  
Interfacial Polymerization ◽  
Pure Water ◽  
Water Flux ◽  
Water Desalination ◽  
Separation Performance ◽  
Salt Rejection ◽  
Tfc Membrane ◽  
Thin Film Nanocomposite

The membrane technology is still considered a costly method to produce potable water. In view of this, RO membrane with enhanced water permeability without trade-off in salt rejection is desirable as it could further reduce the cost for water desalination. In this study, thin film nanocomposite (TFN) membranes containing 0.05 or 0.10 w/v% hydrophilic nanofillers in polyamide layer were synthesized via interfacial polymerization of piperazine and trimesoyl chloride monomers. The resultant TFN membranes were characterized and compared with a control thin film composite (TFC) membrane. Results from the filtration experiments showed that TFN membranes exhibited higher water permeability, salt rejection and fouling resistance compared to that of the TFC membrane. Excessive amount of nanofillers incorporated in the membrane PA layer however negatively affected the cross-linking in the polymer matrix, thus deteriorating the membrane salt rejection. TFN membrane containing 0.05 w/v% of nanofillers showed better performances than the TFC membrane, recording a pure water flux of 11.2 L/m2∙h, and salt rejection of 95.4%, 97.3% and 97.5% against NaCl, Na2SO4 and MgSO4, respectively. 

Morphology and Properties of a Series of PVDF Blend Membranes

2013 ◽  
Vol 750-752 ◽  
pp. 1941-1944
Author(s):  
Jiao Jiao Dong ◽  
Yu Feng Zhang ◽  
Dong Qing Liu
Keyword(s):  
Mechanical Properties ◽  
Pure Water ◽  
Water Flux ◽  
Transformation Method ◽  
Mass Ratio ◽  
Pvdf Membrane ◽  
Blend Membranes ◽  
Pure Water Flux ◽  
And Performance ◽  
Pure Pvdf

In this article, a series of the PVDF/PPTA blend membranes with porous structure and excellent performance were successfully prepared by the phase transformation method. The effect of the mass ratio of W(PVDF)/W(PPTA) was systematically investigated.The morphology of the blend membranes were examined using scanning electron microscope (SEM). The permeation performance was characterized by measuring pure water flux. Meanwhile, the mechanical properties of membranes were researched. The experiment results confirmed that the blending ratio is a major factor to influence the structure and performance of PVDF/PPTA blend membrane. The blend membranes possess much better permeability than pure PVDF membrane and fairly good the mechanical properties especially for the membrane made by PVDF : PPTA=6 : 1.

scholarly journals ENHANCING HYDROPHILICITY OF POLYSULFONE MEMBRANE SURFACE BY UV IRRADIATION OF DIFFERENT WAVELENGTHS AND BY PEG GRAFTING

2021 ◽  
Vol 83 (4) ◽  
pp. 111-117
Author(s):  
Soraya Ruangdit ◽  
Suksawat Sirijaruku ◽  
Thawat Chittrakarn ◽  
Chaiporn Kaew-on
Keyword(s):  
Contact Angle ◽  
Membrane Surface ◽  
Water Flux ◽  
Separation Performance ◽  
Poly Ethylene Glycol ◽  
Uv Treatment ◽  
Water Contact ◽  
Polysulfone Membrane ◽  
Membrane Surfaces ◽  
Poly Ethylene

Polysulfone polymer (PSF) membrane has disadvantages due to its hydrophobicity, which may cause fouling and reduce separation performance. Therefore, this study aimed to enhance the hydrophilicity of PSF membranes by using irradiation at different ultraviolet (UV) wavelengths, followed by Poly(ethylene glycol) (PEG) grafting on the PSF surfaces. The hydrophilicity of the treated membrane surfaces was examined by measuring water contact angle (WCA), surface energy (SE), surface morphology, functional groups, salt rejection, and water flux in a filtration instrument. The results show that with long UV treatment for up to 72 h, the 312 nm wavelength gave lesser WCA than treatment at 254 nm. The treated PSF membrane irradiated at 312 nm for 72 h, followed by PEG grafting, was effectively improved and retained increased hydrophilicity for up to thirty days.

scholarly journals Effect of Polyvinyl Pyrolidone on Morphology and Performance of Cellulose Acetate Based Dialysis Membrane

2019 ◽  
Vol 9 (1) ◽  
pp. 3744-3749
Author(s):  
H. Waheed ◽  
A. Hussain
Keyword(s):  
Contact Angle ◽  
Cellulose Acetate ◽  
Membrane Surface ◽  
Pure Water ◽  
Water Flux ◽  
Mixed Matrix Membrane ◽  
Mixed Matrix ◽  
Urea Clearance ◽  
And Performance ◽  
Operation Phase

Polyvinyl pyrolidone (PVP) was added as filler in cellulose acetate (CA) to produce mixed matrix membrane (MMM) for hemodialysis operation. Phase separation induced by diffusion (DIPS) was used for fabrication of mixed matrix CA/PVP flat sheet membranes. The effect of adding PVP was investigated on the morphology and permeation efficiencies of CA membranes. The surface arrangement of polymer and additives in pure and blended membrane was studied by FTIR, contact angle and SEM. Results revealed homogenous and significant mixing of PVP content into pure CA matrix. Performance efficiency of blended membranes was investigated by means of pure water flux (PWF), urea clearance and % rejection of bovine serum albumin (BSA). The observable decrease of contact angle from 83° to 69° in CA/PVP MMM membranes of varying composition effectively revealed enhancement in hydrophilicity of MMM membrane surface. For protein rejection, all CA/PVP membranes rejected>90% of BSA relative to 25% for pure CA membrane. Furthermore, urea clearance behavior for CA/PVP membranes was 62.4% in comparison to 52% for pure CA membrane. The incorporation PVP i.e 1% by weight (Mpvp1) significantly improved the hydrophilicity, PWF, BSA rejection and urea clearance percentages of modified CA membrane for dialysis application.

Sign in / Sign up

Export Citation Format

Share Document