scholarly journals Preparation and Characterization of MWCNTs/PVDF Conductive Membrane with Cross-Linked Polymer PVA and Study on Its Anti-Fouling Performance

Membranes ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 703
Author(s):  
Yi Ding ◽  
Zhansheng Guo ◽  
Xinan Dong ◽  
Hong You ◽  
Junxue Mei ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Mass Loss Rate ◽  
Pure Water ◽  
Water Flux ◽  
Membrane Properties ◽  
Elongation Ratio ◽  
Functional Layer ◽  
Conductive Membranes ◽  
Pure Water Flux ◽  
Conductive Membrane

Based on carboxylated multi-walled carbon nanotubes (MWCNTs-COOH), a MWCNTs/PVDF conductive membrane was prepared by a vacuum filtration cross-linking method. The surface compositions and morphology of conductive membranes were studied by X-ray photoelectron spectroscopy and high-resolution field emission scanning electron microscopy, respectively. The effects of cross-linked polymeric polyvinyl alcohol (PVA) on the conductive membrane properties such as the porosity, pore size distribution, pure water flux, conductivity, hydrophilicity, stability and antifouling properties were investigated. Results showed that the addition of PVA to the MWCNTs/PVDF conductive membrane decreased the pure water flux, porosity and the conductivity. However, the hydrophilicity of the modified MWCNTs/PVDF conductive membrane was greatly improved, and the contact angle of pure water was reduced from 70.18° to 25.48° with the addition of PVA contents from 0 wt% to 0.05 wt%. Meanwhile, the conductive membranes with higher content had a relatively higher stability. It was found that the conductive functional layer of the conductive membrane had an average mass loss rate of 1.22% in the 30 min ultrasonic oscillation experiment. The tensile intensity and break elongation ratio of the conductive membrane are improved by the addition of PVA, and the durability of the conductive membrane with PVA was superior to that without PVA added. The electric assisted anti-fouling experiments of modified conductive membrane indicated that compared with the condition without electric field, the average flux attenuation of the conductive membrane was reduced by 11.2%, and the membrane flux recovery rate reached 97.05%. Moreover, the addition of PVA could accelerate the clean of the conductive membranes.

Composite Membrane with a Calixarene-Containing Polyamide Functional Layer

2018 ◽  
Vol 71 (5) ◽  
pp. 360 ◽  
Author(s):  
Shun Ren ◽  
Dong-Qing Liu ◽  
Rui-Xiang Miao ◽  
Ze-Xian Zhu ◽  
Yu-Feng Zhang
Keyword(s):  
Composite Membrane ◽  
Photoelectron Spectroscopy ◽  
Interfacial Polymerization ◽  
Film Formation ◽  
Pure Water ◽  
Water Flux ◽  
Metal Cations ◽  
Heat Treating ◽  
Skin Layer ◽  
Functional Layer

Monolayer thin films were prepared at the interface of hexane and water to investigate the film formation ability of monomers through interfacial polymerization (IP). A tetra-calix[4]arene chloride derivative (CC) and a diamino-terminated PEG-1000 (DAP) produced a high strength membrane among the tested monomers. IP is consequently proposed to prepare a composite membrane with CC and DAP on a polysulfone (PSF) bulk membrane used for ultrafiltration. The top layer was cross-linked by heat-treating at 60°C for 2 min, with DAP (2 wt.-%) in water and CC (0.05 wt.-%) in hexane. Attenuated total reflectance (ATR)-FTIR and X-ray photoelectron spectroscopy data confirmed that a polyamide was formed on the surface of the PSF substrate. The skin layer was a 3 μm thick smooth thin-film as determined by field emission scanning electron microscopy (FE-SEM), and was also compact without gaps. Pure water flux was ~80.5 L m−2 h−1 under 0.5 MPa. Rejection of MgSO4 was round 22 %, since the calixarene-containing network was a sparse grid, and also had an affinity for metal cations. Although the skin of the composite membrane was compact under SEM, it was easy for metal cations to transfer through. This composite membrane might have good performance in other separation areas as a result of the special structure imparted by using the calixarenes as cross-linking knots.

Excellent hydrophilicity of polyurethane modified polyvinylidene fluoride

2021 ◽  
pp. 1-8
Author(s):  
Jiale Qu ◽  
Shen Gao ◽  
Zhenghao Hou
Keyword(s):  
Polyvinylidene Fluoride ◽  
Pure Water ◽  
Water Flux ◽  
Membrane Properties ◽  
Pvdf Membrane ◽  
Sem Image ◽  
Low Surface Energy ◽  
Blending Method ◽  
Pure Water Flux ◽  
Pure Pvdf

Polyvinylidene fluoride (PVDF) is a promising membrane material in ultrafiltration (UF) applications; its extensive application however is limited due to the disadvantage in hydrophilicity and low surface energy. Herein, a sort of TPU-modified PVDF membrane is prepared by blending method and its hydrophilicity is compared with a series of pure/modified PVDF membranes. The contact angle and pure water flux (PWF) results demonstrate that the hydrophilicity of the TPU-modified PVDF membrane is enhanced, and the performance is not inferior to that of traditional pore-modified PVDF membranes. SEM image shows that the TPU-modified PVDF membrane maintains morphology of the pure PVDF membrane, indicating that TPU molecules have excellent compatibility with PVDF molecules and can maintain the mechanical property of PVDF membrane to a certain extent. Finally, we explore the effects of TPU molecules and PVDF molecules on water molecules, respectively, from a microscopic perspective involving first principles. This investigation not only establishes that PVDF membrane has been prepared with enhanced hydrophilicity, but also provides a novel avenue for the modification of membrane properties.

scholarly journals Preparation and Characterization of AgNp/PVDF Cmposite Ultrafiltration Membrane

2018 ◽  
Vol 24 (7) ◽  
pp. 50
Author(s):  
Mohammed Amer Abdul-Majeed
Keyword(s):  
Silver Nanoparticles ◽  
Composite Membrane ◽  
Ag Nanoparticles ◽  
Pure Water ◽  
Water Flux ◽  
Ultrafiltration Membrane ◽  
Membrane Properties ◽  
Inversion Method ◽  
Pvdf Membrane ◽  
Pure Water Flux

In this study, polymeric ultrafiltration (UF) membranes were prepared by phase inversion method to obtain both antibacterial and organic antifouling properties. The membranes were cast from a solution of polyvinylidene fluoride (PVDF) and formative silver (Ag) nanoparticles were successfully immobilized on a polymer. This was done using a solvent N, N-dimethylformamide (DMF) which is a solvent for the PVDF polymer meanwhile it is a reducing agent for silver ion. The effect of silver nanoparticles additives on the performance of polymeric ultrafiltration membrane was verified. Chemical composition and morphology of the surfaces of the membranes were characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscope (SEM). The antibacterial property of modified membrane and the influence of silver nanoparticles on pure water flux of composite membrane at 0.2 Mpa were also verified. The experimental results obtained concluded that the composite membrane properties have been improved by the integration of Ag nanoparticles. The grafted membrane with silver nanoparticles has shown a clear ability to inhibit the growth of E. coli, Pseudomonas Aeruginosa, and Bacillus Cereus. While the clean PVDF membrane (without any additives) did not show any effect of preventing the growth of these species of bacteria referred to above. The pure water flux, porosity and the mean pore size of composite membrane can reach 261.8 L/m2 h, 85.4%, and 0.0206 µm, respectively, and it was much more than that of pure PVDF membrane.  

Preparation and Characterization of Hydrophilic PVDF Hollow Fiber Ultrafiltration Membrane

2011 ◽  
Vol 480-481 ◽  
pp. 201-206
Author(s):  
Li Guo Wang ◽  
Xiu Ju Wang ◽  
Ai Min Wang ◽  
Wen Juan Liu ◽  
Shi Qi Guo ◽  
...  
Keyword(s):  
Acrylic Acid ◽  
Hollow Fiber ◽  
Polyvinylidene Fluoride ◽  
Breaking Strength ◽  
Pure Water ◽  
Water Flux ◽  
Technical Parameters ◽  
Rupture Pressure ◽  
Pure Water Flux

Hydrophilic Polyvinylidene fluoride (PVDF) hollow fiber ultrafiltration membranes were prepared by wet-spinning method. The effects of technical parameters of acrylic acid grafted onto PVDF on the performance of hydrophilic PVDF membranes were investigated via orthogonal test, the technical parameters of preparation of hydrophilic PVDF membranes were determined, and hydrophilic PVDF membranes were prepared. Then hydrophilic PVDF membranes were characterized in terms of breaking strength, breaking elongation, rupture pressure, pure water flux and rejection. The fouling properties and the conditions of acrylic acid grafted onto PVDF were also examined. The results showed that acrylic acid had been grafted onto PVDF, the breaking strength and rupture pressure improved greatly, and the fouling properties were better than PS hollow fiber UF membrane.

THE FEASIBILITY OF KAOLIN AS MAIN MATERIAL FOR LOW COST POROUS CERAMIC HOLLOW FIBRE MEMBRANE PREPARED USING COMBINED PHASE INVERSION AND SINTERING TECHNIQUE

2017 ◽  
Vol 79 (1-2) ◽  
Author(s):  
Siti Khadijah Hubadillah ◽  
Mohd Hafiz Dzarfan Othman ◽  
A. F. Ismail ◽  
Mukhlis A. Rahman ◽  
Juhana Jaafar
Keyword(s):  
Phase Inversion ◽  
Low Cost ◽  
Pure Water ◽  
Porous Ceramic ◽  
Water Flux ◽  
Hollow Fibre ◽  
Hollow Fibre Membrane ◽  
Fibre Membrane ◽  
Pure Water Flux ◽  
And Performance

Ceramic hollow fibre membrane (CHFM) demonstrated superior characteristics and performance in any separation application. The only problem associated with this kind of technology is the high cost. In order to effectively fabricate and produce low cost porous CHFM, a series of CHFMs made of kaolin were fabricated via combined phase inversion and sintering technique. The CHFMs from kaolin named as kaolin hollow fibre membranes (KHFMs) were studied at different kaolin contents of 35 wt.%, 37.5 wt.% and 40 wt.% sintered at 1200ºC. The result indicated that by varying kaolin contents, different morphologies were obtained due to changes in the viscosity of ceramic suspension containing kaolin. The optimum kaolin content for KHFM was identified. It was found that KHFM prepared at 37.5 wt% has a mechanical strength and pure water flux of A and B respectively.  

Influence of Hydrophilic Polymer on Pure Water Permeation, Permeability Coefficient, and Porosity of Polysulfone Blend Membranes

2014 ◽  
Vol 931-932 ◽  
pp. 168-172 ◽  
Author(s):  
Asmadi Ali ◽  
Mohamad Awang ◽  
Ramli Mat ◽  
Anwar Johari ◽  
Mohd Johari Kamaruddin ◽  
...  
Keyword(s):  
Permeability Coefficient ◽  
Pure Water ◽  
Polymer Concentration ◽  
Water Flux ◽  
Hydrophilic Polymer ◽  
Hydrophobic Property ◽  
Water Permeation ◽  
Blend Membranes ◽  
Wet Phase Inversion ◽  
Pure Water Flux

It is well known that membrane with hydrophobic property is a fouling membrane. Polysulfone (PSf) membrane has hydrophobic characteristic was blended with a hydrophilic polymer, cellulose acetate phthalate (CAP) in order to increase hydrophilicity property of pure PSf membrane. In this study, membrane casting solutions containing 17 wt% of polymer was prepared via wet phase inversion process. The pure PSf membrane was coded as PC-0. PSf/CAP blend membranes with blend composition of 95/5, 90/10, 85/15 and 80/20 wt% of total polymer concentration in the membrane casting solutions were marked as PC-5, PC-10, PC-15 and PC-20 respectively. All of the membranes were characterized in terms of pure water flux and permeability coefficient in order to study their hydrophilicity properties. The investigated results shows that increased of CAP composition in PSf blend membranes has increased pure water flux, permeability coefficient and porosity of the blend membrane which in turn formed membrane with anti-fouling property.

scholarly journals The Modification of PVDF Membrane via Crosslinking with Chitosan and Glutaraldehyde as the Crosslinking Agent

2018 ◽  
Vol 18 (1) ◽  
pp. 1
Author(s):  
Romaya Sitha Silitonga ◽  
Nurul Widiastuti ◽  
Juhana Jaafar ◽  
Ahmad Fauzi Ismail ◽  
Muhammad Nidzhom Zainol Abidin ◽  
...  
Keyword(s):  
Contact Angle ◽  
Vinylidene Fluoride ◽  
Membrane Surface ◽  
Pure Water ◽  
Water Flux ◽  
Crosslinking Agent ◽  
Hydrophobic Properties ◽  
Pvdf Membrane ◽  
Pure Water Flux ◽  
Modified Membrane

Poly(vinylidene fluoride) (PVDF) has outstanding properties such as high thermal stability, resistance to acid solvents and good mechanical strength. Due to its properties, PVDF is widely used as a membrane matrix. However, PVDF membrane is hydrophobic properties, so as for specific applications, the surface of membrane needs to be modified to become hydrophilic. This research aims to modify PVDF membrane surface with chitosan and glutaraldehyde as a crosslinker agent. The FTIR spectra showed that the modified membrane has a peak at 1655 cm-1, indicating the imine group (–N=C)- that was formed due to the crosslink between amine group from chitosan and aldehyde group from glutaraldehyde. Results showed that the contact angle of the modified membrane decreases to 77.22° indicated that the membrane hydrophilic properties (< 90°) were enhanced. Prior to the modification, the contact angle of the PVDF membrane was 90.24°, which shows hydrophobic properties (> 90°). The results of porosity, Ɛ (%) for unmodified PVDF membrane was 55.39%, while the modified PVDF membrane has a porosity of 81.99%. Similarly, by modifying the PVDF membrane, pure water flux increased from 0.9867 L/m2h to 1.1253 L/m2h. The enhancement of porosity and pure water flux for the modified PVDF membrane was due to the improved surface hydrophilicity of PVDF membrane.

The Optimization of RHS-polysulfone Membrane towards Operating Condition for Humic Acid Removal

2021 ◽  
Vol 02 (01) ◽  
Author(s):  
Mohd Riduan Jamalludin ◽  
◽  
Siti Khadijah Hubadillah ◽  
Zawati Harun ◽  
Muhamad Zaini Yunos ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Ionic Strength ◽  
Membrane Separation ◽  
Pure Water ◽  
Water Flux ◽  
Separation Process ◽  
Transmembrane Pressure ◽  
Polysulfone Membrane ◽  
Optimal Value ◽  
Pure Water Flux

This study investigates the effects of rice husk silica (RHS) as additive in the polysulfone membrane to enhance antifouling properties in membrane separation process. The performance (of what?) was evaluated in term of pure water flux (PWF), rejection and antifouling properties. The optimized of normalized flux (Jf /Jo) at different parameter in filtration (pH, ionic strength and tranmembrane-pressure) was carried out by using the response surface methodology (RSM). The results showed that the addition of 4 wt. % RHS give the highest flux at 300.50 L/m².hour (LMH). The highest rejection was found at 3 wt. % of RHS membrane with value 98% for UV254 and 96% for TOC. The optimal value of Jf/Jo was found at 0.62 with the condition of pH: 6.10, ionic strength: 0.05 mol/L and transmembrane-pressure: 2.67 bars. Optimize of RSM analysis from ANOVA also proved that the error of model is less than 0.05% which indicates that the model is significant.

scholarly journals Mixed-Matrix Membranes Comprising of Polysulfone and Porous UiO-66, Zeolite 4A, and Their Combination: Preparation, Removal of Humic Acid, and Antifouling Properties

Membranes ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 393
Author(s):  
Tanzila Anjum ◽  
Rahma Tamime ◽  
Asim Laeeq Khan
Keyword(s):  
Humic Acid ◽  
High Performance ◽  
Synergistic Effects ◽  
Pure Water ◽  
Water Flux ◽  
Mixed Matrix Membranes ◽  
Mixed Matrix ◽  
Zeolite 4A ◽  
Pure Water Flux ◽  
Matrix Membranes

High-performance Mixed-Matrix Membranes (MMMs) comprising of two kinds of porous fillers UiO-66 and Zeolite 4Aand their combination were fabricated with polysulfone (PSf) polymer matrix. For the very first time, UiO-66 and Zeolite 4A were jointly used as nanofillers in MMMs with the objective of complimenting synergistic effects. The individual and complimentary effects of nanofillers were investigated on membrane morphology and performance, pure water flux, humic acid rejection, static humic acid adsorption, and antifouling properties of membranes. Scanning Electron Microscopy (SEM) analysis of membranes confirmed that all MMMs possessed wider macrovoids with higher nanofiller loadings than neat PSf membranes and the MMMs (PSf/UiO-66 and PSf/Zeolite 4A-UiO-66) showed tendency of agglomeration with high nanofiller loadings (1 wt% and 2 wt%). All MMMs exhibited better hydrophilicity and lower static humic acid adsorption than neat PSf membranes. Pure water flux of MMMs was higher than neat PSf membranes but the tradeoff between permeability and selectivity was witnessed in the MMMs with single nanofiller. However, MMMs with combined nanofillers (PSf/Zeolite 4A-UiO-66) showed no such tradeoff, and an increase in both permeability and selectivity was achieved. All MMMs with lower nanofiller loadings (0.5 wt% and 1 wt%) showed improved flux recovery. PSf/Zeolite 4A-UiO-66 (0.5 wt%) membranes showed the superior antifouling properties without sacrificing permeability and selectivity.

scholarly journals Vanillin as an Antifouling and Hydrophilicity Promoter Agent in Surface Modification of Polyethersulfone Membrane

Membranes ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 56 ◽  
Author(s):  
Mohammadamin Esmaeili ◽  
Tiina Virtanen ◽  
Jussi Lahti ◽  
Mika Mänttäri ◽  
Mari Kallioinen
Keyword(s):  
Pure Water ◽  
Water Flux ◽  
Adsorption Potential ◽  
Exposure Concentration ◽  
Polyethersulfone Membrane ◽  
Pure Water Flux ◽  
Wood Extract ◽  
Surface Modified ◽  
Glycol Solution ◽  
Lower Contact

Fouling as an intricate process is considered as the main obstacle in membrane technologies, and its control is one of the main areas of attention in membrane processes. In this study, a commercial polyethersulfone ultrafiltration membrane (MWCO: 4000 g/mol) was surface modified with different concentrations of vanillin as an antifouling and hydrophilicity promoter to improve its performance. The presence of vanillin and its increasing adsorption potential trends in higher vanillin concentrations were clearly confirmed by observable changes in FTIR (Fourier transform infrared) spectra after modification. Membranes with better hydrophilicity (almost 30% lower contact angle in the best case) and higher polyethylene glycol solution (PEG) permeability were achieved after modification, where a 35–38% increase in permeability of aqueous solution of PEG was perceived when the membrane was modified at the highest exposure concentration of vanillin (2.8 g/L). After filtration of wood extract, surface modified membrane (2.8 g/L vanillin) showed better antifouling characteristics compared to unmodified membrane, as indicated by approximately 22% lower pure water flux reduction, which in turn improved the separation of lignin from the other organic compounds present in wood extract.

Sign in / Sign up

Export Citation Format

Share Document