scholarly journals Material microstructure effects in micro-endmilling of Cu99.9E

2016 ◽  
Vol 232 (7) ◽  
pp. 1143-1155 ◽  
Author(s):  
AM Elkaseer ◽  
SS Dimov ◽  
DT Pham ◽  
KP Popov ◽  
L Olejnik ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Grain Size ◽  
Chip Thickness ◽  
Micro Milling ◽  
Coarse Grained ◽  
Material Microstructure ◽  
Micro Cutting ◽  
Minimum Chip Thickness ◽  
Average Grain Size ◽  
Material Homogeneity

This article presents an investigation of the machining response of metallurgically and mechanically modified materials at the micro-scale. Tests were conducted that involved micro-milling slots in coarse-grained Cu99.9E with an average grain size of 30 µm and ultrafine-grained Cu99.9E with an average grain size of 200 nm, produced by equal channel angular pressing. A new method based on atomic force microscope measurements is proposed for assessing the effects of material homogeneity changes on the minimum chip thickness required for a robust micro-cutting process with a minimum surface roughness. The investigation has shown that by refining the material microstructure the minimum chip thickness can be reduced and a high surface finish can be obtained. Also, it was concluded that material homogeneity improvements lead to a reduction in surface roughness and surface defects in micro-cutting.

An experimental analysis of minimum chip thickness in micro-milling of two different titanium alloys

2020 ◽  
Vol 234 (12) ◽  
pp. 1486-1498 ◽  
Author(s):  
Kubilay Aslantas ◽  
Luqman KH Alatrushi ◽  
Fevzi Bedir ◽  
Yusuf Kaynak ◽  
Nihat Yılmaz
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Ti6al4v Alloy ◽  
Micro Milling ◽  
Depth Of Cut ◽  
Minimum Chip Thickness ◽  
Burr Width

Micro-milling is a micro-mechanical cutting method used to obtain complex and three-dimensional micro geometries. Micro-cutting tools are used in the manufacturing of micro-components and the type of workpiece is also important for good surface quality and minimum burr. In this study, micro machinability of Ti6Al4V alloy which is used most frequently in micro-component production is compared with Ti5553 alloy. Micro-milling of Ti5553 alloy and comparison of the minimum chip thickness with Ti6Al4V were performed for the first time in this study. Using different cutting parameters, the variation of surface roughness, burr width, and cutting forces were investigated. The cutting tests were carried out on a specially designed and high-precision micro-milling test system using a TiCN-coated two-flute end mill of 0.6 mm diameter. According to the results, minimum chip thickness is approximately 0.3 times the edge radius of the cutting tool and does not vary with the alloy type. At feed rates smaller than the minimum chip thickness, both the cutting forces increase and the surface quality decreases. For both alloys, reduced feed rate and increased depth of cut lead to increased burr width. The burr widths in Ti6Al4V alloy are higher. At the end of the study, the limits of the cutting parameters where plowing occurred for the both alloys are clearly determined. In addition, the limits of the cutting parameter causing plowing have been confirmed by cutting forces, surface roughness, and burr formation.

Mikrofräswerkzeuge mit Schneiden aus cBN*/Micro-cutting tools with cBN cutters

2018 ◽  
Vol 108 (11-12) ◽  
pp. 773-777
Author(s):  
E. Uhlmann ◽  
J. Polte ◽  
M. Polte ◽  
Y. Kuche ◽  
H. Wiesner
Keyword(s):  
Surface Roughness ◽  
Cubic Boron Nitride ◽  
Cutting Tools ◽  
High Strength ◽  
Hardened Steel ◽  
Micro Milling ◽  
Geometric Accuracy ◽  
Micro Cutting ◽  
Core Technology ◽  
Milling Tools

Die Mikrozerspanung ist eine Kerntechnologie bei der Fertigung von Mikrospritzgussformen. Die hohen Ansprüche an die geometrische Genauigkeit und Oberflächenrauheit erfordern den Einsatz hochfester Werkstoffe. Jedoch unterliegen aktuelle Fräswerkzeuge bei der Mikrozerspanung einem hohen Verschleiß. Einen Lösungsansatz bietet der erfolgreich in der Makrozerspanung eingesetzte Schneidstoff kubisch-kristallines Bornitrid (cBN). Ziel der Untersuchungen war es daher, detaillierte Informationen zur Bearbeitung von gehärtetem Stahl mit cBN-Mikrofräswerkzeugen bereitstellen zu können.   Micro-cutting is a core technology for producing micro-injection moulds. High demands on geometric accuracy and surface roughness require high-strength materials. However, current milling tools for micro-cutting suffer from excessiv tool wear. A solution is offered by cutting materials based on cubic Boron Nitride (cBN), which have been used successfully in macro-machining. This article contains detailed information on the machining of hardened steel with micro-milling tools and cutting edges made of cBN.

Grain Structure and Surface Roughness of Four Commercial NiTi Orthodontic Archwires

2017 ◽  
Vol 266 ◽  
pp. 257-263
Author(s):  
Wassana Wichai ◽  
Rutchadakorn Isarapatanapong ◽  
Niwat Anuwongnukroh ◽  
Surachai Dechkunakorn
Keyword(s):  
Surface Roughness ◽  
Grain Size ◽  
Optical Microscope ◽  
Grain Structure ◽  
Wire Surface ◽  
Average Grain Size ◽  
Electron Mode ◽  
The Mean ◽  
The Wire ◽  
Orthodontic Archwires

This study investigated four commercially available NiTi orthodontic archwires from different manufactures for their grain structure and surface roughness.Four commercially available pre-formed NiTi orthodontic archwire (Ormco, Sentalloy, Highland and NIC) with diameter 0.016 x 0.022 inch2 were tested. The wire samples were polished and etched to evaluate the morphology and structure of wire surface. Each NiTi archwire was investigated under a reflected light microscope of an Optical Microscope to analyze its grain structure and size, in longitudinal surfaces. The surfaces of wire were qualitatively examined in the secondary electron mode at common magnification (500X). The surface roughness was also evaluated by a surface roughness tester. The descriptive statistic was evaluated the mean and standard deviation of surface roughness and Medcale T-Test was to test the mean difference of the surface roughness in each brands. This study showed an average grain size of 2-8 μm for each NiTi archwire. The wire surface of Ormco and Highland showed straiations along the longitudinal axes, however Sentalloy and NIC showed small pores on the wire surface. The surface roughness was 0.09 μm for Highland, 0.25 μm for Sentalloy, 0.28 μm for Ormco and 0.46 μm for NIC archwire. The Highland was smoothest and NIC was the roughest. There were in significant (p < 0.05) difference of surface roughness of each brands. The results showed that the four manufactures NiTi archwires were different in grain size, wire surface and surface roughness. During clinical application, these archwires may exhibit different mechanical properties, such as strength, hardness, ductity, and friction because of their microstructure.

scholarly journals Effect of Ultrasonic Surface Rolling Treatment on Corrosion Behavior of Alloy 690

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 917 ◽  
Author(s):  
Jiang Liu ◽  
Junbiao Liu ◽  
Xuehui Zhang ◽  
Tahir Ahmad ◽  
Tongxiang Liang ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Layer ◽  
Corrosion Behavior ◽  
Electrochemical Corrosion ◽  
Coarse Grained ◽  
Alloy 690 ◽  
Average Grain Size ◽  
Before And After ◽  
Immersion Experiment ◽  
Secondary Side

The nanograins (NG) on the top surface layer of alloy 690 were successfully prepared by ultrasonic surface rolling treatment (USRT). The average grain size of NG alloy 690 was 55 nm, and the thickness of the NG surface layer was about 1 μm. Meanwhile, the surface roughness was significantly reduced after surface nanocrystalliztion. The corrosion behavior of alloy 690 before and after USRT was studied in a secondary side environment containing chloride. Electrochemical corrosion experiments demonstrated that the passive film generated by USRT was denser than that formed on coarse-grained (CG) alloy 690. Pitting corrosion was prone to occur in grain boundaries of CG alloy 690, and the pits on the surface of NG alloy 690 were smaller than those generated on CG alloy 690 after 1000 h of an immersion experiment.

Investigation on Mechanism of Ultra-Smoothed Surface with a Micro Slot on the Flank Face in Micro Cutting

2014 ◽  
Vol 651-653 ◽  
pp. 764-767
Author(s):  
Tao Zhang ◽  
Hou Jun Qi ◽  
Gen Li
Keyword(s):  
Surface Roughness ◽  
Chip Thickness ◽  
Cutting Edge ◽  
Back Side ◽  
Uncut Chip Thickness ◽  
Micro Cutting ◽  
Cutting Edge Radius ◽  
Edge Radius ◽  
Flank Face ◽  
Side Flow

Micro cutting is a promising manufacturing method to obtain good surface integrity. Surface roughness shows size effect when the uncut chip thickness is smaller than the cutting edge radius. A special micro slot on the flank face of cutting tools was manufactured with discharge. Two groups of micro orthogonal cutting were conducted. The surface roughness of machined surface was measured and compared to each other. The results show that surface roughness decreases first and then increases with the ratio of uncut chip thickness to cutting edge radius. The surface machined with micro slot is better than that of without micro slot due to the micro slot restrain the back side flow of work piece based on the finite element model.

Experimental Evaluation of Surface Roughness in Orthogonal Micro-Milling Processes

2012 ◽  
Vol 217-219 ◽  
pp. 1912-1916
Author(s):  
Ji Hua Wu
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Experimental Approach ◽  
Critical Role ◽  
Cutting Speed ◽  
Chip Thickness ◽  
Micro Milling ◽  
Surface Model ◽  
Material Grain Size

Surface roughness plays a critical role in evaluating and measuring the surface quality of a machined product. Two workpiece materials have been investigated by experimental approach in order to gain a better understanding of their influence on the obtained surface roughness in the micro-milling processes. The experimental results show that: surface topography is completely different for different materials at the same cutting speed and feed rate; surface roughness increases with an increase of material grain size. Surface roughness decreases to a lowest value, and then increases with an increase of the feed rate. A new surface model to illustrate the influence of material and uncut chip thickness was developed. The model has been experimentally validated and shows more promising results than Weule’s model.

Topography and Surface Roughness of Floor in Groove Micro Milling

2014 ◽  
Vol 30 (6) ◽  
pp. 667-678 ◽  
Author(s):  
S. Kouravand ◽  
B. M. Imani ◽  
J. Ni
Keyword(s):  
Surface Roughness ◽  
Elastic Recovery ◽  
Chip Thickness ◽  
Cutting Process ◽  
Micro Milling ◽  
Tool Geometry ◽  
Proposed Model ◽  
Milling Operation ◽  
Micro Parts ◽  
Finishing Processes

AbstractMicro milling operation is a fabrication process to create 3D parts from tens of micrometers to a few millimeters in size using a tool with diameter less than 1mm. Micro groove is one of the common features observed in the micro parts. The surface roughness of micro grooves plays an important role in their performance. Since most of the finishing processes could not be easily performed on the micro grooves, it is of extreme importance to find a relationship between micro milling parameters and the surface roughness profile. In this paper, in order to anticipate the profile and surface roughness of the groove floor a model is proposed based on the kinematic of cutting process and tool geometry. The effects of minimum chip thickness, elastic recovery, size effect and tool deflection are included in the model. Relationship between position of points on the floor surface of groove and kinematics of cutting process are derived. In next step, simulations of proposed model are performed in the ACIS environment. Finally, using the DOE method surface roughness is investigated stochastically. The simulated and measured surface roughnesses are compared together that confirm the validity of proposed model.

A Micromilling Experimental Study on AISI 4340 Steel

2009 ◽  
Vol 407-408 ◽  
pp. 335-338 ◽  
Author(s):  
Jin Sheng Wang ◽  
Da Jian Zhao ◽  
Ya Dong Gong
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Cutting Force ◽  
Spectrum Analysis ◽  
Chip Thickness ◽  
Experimental Results ◽  
Minimum Chip Thickness ◽  
Aisi 4340 Steel ◽  
4340 Steel ◽  
Aisi 4340

A micromilling experimental study on AISI 4340 steel is conducted to understand the micromilling principle deeply. The experimental results, especially on the surface roughness and cutting force, are discussed in detail. It has been found the minimum chip thickness influences the surface roughness and cutting force greatly. Meanwhile, the material elastic recover induces the increase of the axial micromilling force. The average cutting force and its spectrum analysis validate the minimum chip thickness approximation of AISI 4340 is about 0.35μm.

Influence of Grain Size on Mechanical Properties in a Fe-9Ni-12Mn-2.5Si-1.0C TWIP Steel

2011 ◽  
Vol 197-198 ◽  
pp. 655-661
Author(s):  
Ze Bin Yang ◽  
Ding Yi Zhu ◽  
Wei Fa Yi ◽  
Shu Mei Lin ◽  
Cheng Mei Du
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Strain Hardening ◽  
Twip Steel ◽  
Optical Microscope ◽  
Coarse Grained ◽  
Microstructure Observation ◽  
Transmission Electron ◽  
Average Grain Size

We investigate the influence of grain size on mechanical properties in a Fe-9Ni-12Mn-2.5Si-1.0C TWIP steel by unidirectional tensile. Meanwhile the microstructures of the TWIP steel were observed and analyzed by optical microscope (OM) and transmission electron microscope (TEM). The experimental results show that the TWIP steel’s yield strength and tensile strength decrease with the increasing of grain size, whereas the plasticity increases with it. When the average grain size reaches to 27μm, the tensile strength is 1080MPa, the elongation percentage is 77%, and the strength-plasticity product achieves the 83160MPa•%. Steel’s strain hardening rate can be changed from three-stage to four-stage with the increasing of grain sizes, the areas of strain hardening by twin deformation mechanism are expanded. Through the microstructure observation we found that, coarse-grained TWIP steel conducts to twinning formation, the high density twins can increase the alloy’s ductility by splitting the grain.

scholarly journals Microstructure-Based 3D FE Modeling for Micro Cutting Ferritic-Pearlitic Carbon Steels

2014 ◽  
Author(s):  
M. Abouridouane ◽  
F. Klocke ◽  
D. Lung
Keyword(s):  
Size Effects ◽  
Chip Thickness ◽  
Rake Angle ◽  
Carbon Steels ◽  
Micro Milling ◽  
Fe Model ◽  
Two Phase ◽  
Workpiece Material ◽  
Micro Cutting ◽  
Feed Force

The mechanics of the cutting process on the microscopic level differ fundamentally from the conventional macro cutting. For example, the tool edge radius influences the cutting mechanism in micro machining significantly with regard to the effective rake angle, the minimum chip thickness, the dominance of ploughing, and the related elasto-plastic deformation of the workpiece material. These phenomena, known as size effects, have a profound impact on the cutting force, process stability, and resulting surface finish in micro cutting. Therefore, microstructural effects in microscale cutting require quite different assumptions to be made concerning underlying material behaviour during micro cutting and have led to the need for new modeling approaches to account for such effects. This paper presents a three-dimensional finite element approach to incorporate microstructure into micro cutting simulation based on the concept of a representative volume element (RVE) and constitutive material modeling as well as using the Lagrangian formulation proposed in the implicit FE code Deform 3D™. Micro drilling and micro milling tests using solid carbide tools with different diameters (d = 50 μm − 1 mm) were performed on ferrite-pearlite two-phase steel AISI 1045 for the verification of the developed 3D multiphase FE computation model regarding chip formation, feed force, and torque. The developed 3D multiphase FE model was successfully used to predict size effects in micro cutting.

Sign in / Sign up

Export Citation Format

Share Document