Grain Structure and Surface Roughness of Four Commercial NiTi Orthodontic Archwires

2017 ◽  
Vol 266 ◽  
pp. 257-263
Author(s):  
Wassana Wichai ◽  
Rutchadakorn Isarapatanapong ◽  
Niwat Anuwongnukroh ◽  
Surachai Dechkunakorn
Keyword(s):  
Surface Roughness ◽  
Grain Size ◽  
Optical Microscope ◽  
Grain Structure ◽  
Wire Surface ◽  
Average Grain Size ◽  
Electron Mode ◽  
The Mean ◽  
The Wire ◽  
Orthodontic Archwires

This study investigated four commercially available NiTi orthodontic archwires from different manufactures for their grain structure and surface roughness.Four commercially available pre-formed NiTi orthodontic archwire (Ormco, Sentalloy, Highland and NIC) with diameter 0.016 x 0.022 inch2 were tested. The wire samples were polished and etched to evaluate the morphology and structure of wire surface. Each NiTi archwire was investigated under a reflected light microscope of an Optical Microscope to analyze its grain structure and size, in longitudinal surfaces. The surfaces of wire were qualitatively examined in the secondary electron mode at common magnification (500X). The surface roughness was also evaluated by a surface roughness tester. The descriptive statistic was evaluated the mean and standard deviation of surface roughness and Medcale T-Test was to test the mean difference of the surface roughness in each brands. This study showed an average grain size of 2-8 μm for each NiTi archwire. The wire surface of Ormco and Highland showed straiations along the longitudinal axes, however Sentalloy and NIC showed small pores on the wire surface. The surface roughness was 0.09 μm for Highland, 0.25 μm for Sentalloy, 0.28 μm for Ormco and 0.46 μm for NIC archwire. The Highland was smoothest and NIC was the roughest. There were in significant (p < 0.05) difference of surface roughness of each brands. The results showed that the four manufactures NiTi archwires were different in grain size, wire surface and surface roughness. During clinical application, these archwires may exhibit different mechanical properties, such as strength, hardness, ductity, and friction because of their microstructure.

Annealing Treatment for Superplastic Forming of Twin Roll Casted AZ31 Magnesium Sheet

2011 ◽  
Vol 239-242 ◽  
pp. 50-54 ◽  
Author(s):  
Guo Dong Shi ◽  
Jun Qiao
Keyword(s):  
Grain Size ◽  
Grain Growth ◽  
Mechanical Test ◽  
Dynamic Balance ◽  
Annealing Treatment ◽  
Optical Microscope ◽  
Grain Structure ◽  
Average Grain Size ◽  
Az31 Sheet ◽  
Twin Roll

Annealing treatments at 200°C, 250 °C, 300°C, and 350°C were conducted on a twin-roll casted AZ31 sheet with an initial average grain size of 10.11 mm. Microstructure and mechanical behaviors were studied by optical microscope observation and tensile mechanical test. Expermeintal results show that grain size experienced three stage evolution during 180 min annealing at each temperature: recrystallization refinement, stabilization under dynamic balance of recrystallization and grain growth, and grain growth. The minimum average grain size of 5.96 μm was achieved after 120 min annealing at 200°C. The refined grain structure causes a decrease of ultimate tensile strength and an increase of elongation, and facilitates superplastic deformation of the material.

Isothermal Oxidation Behavior of Fe-33Ni-18Cr Alloy in Different Heat Treatment Temperature

2020 ◽  
Vol 1010 ◽  
pp. 46-51
Author(s):  
Zahraa Zulnuraini ◽  
Noraziana Parimin
Keyword(s):  
Heat Treatment ◽  
Grain Size ◽  
Heat Treatment Temperature ◽  
Minimum Weight ◽  
Isothermal Oxidation ◽  
Optical Microscope ◽  
Treatment Temperature ◽  
Grain Structure ◽  
X Ray ◽  
Average Grain Size

This research study describes the influence of different heat treatment temperature on isothermal oxidation of Fe-33Ni-18Cr alloy. The Fe-33Ni-18Cr alloy was undergone heat treatment at three different temperatures, namely 1000 °C, 1100 °C and 1200 °C for 3h soaking time followed by water quench to vary the grain size of the alloy. This alloy was ground by using several grit of silicon carbide papers as well as weighed by using analytical balance and measured by using Vernier caliper before oxidation test. The heat-treated Fe-33Ni-18Cr alloy was isothermally oxidized at 800 °C for 150h. The characterization of oxidized samples was carried out using optical microscope, scanning electron microscope equipped with energy dispersive x-ray (SEM-EDX) and x-ray diffraction (XRD). The results showed that, increasing the heat treatment temperature was increased the average grain size. The kinetics of oxidation followed the parabolic rate law which represents diffusion-controlled oxide growth rate. Fine grain structure of 1000 °C sample shows minimum weight gain and lower oxidation rate compared to samples of 1100 °C and 1200 °C that indicated oxide spallation and porous structure. Besides, phase analysis showed that the oxidized sample formed several oxide phases.

Effect of Heat Treatment on Isothermal Oxidation of Fe-33Ni-18Cr Alloy at 1000°C

2020 ◽  
Vol 1010 ◽  
pp. 9-14
Author(s):  
Zahraa Zulnuraini ◽  
Noraziana Parimin
Keyword(s):  
Heat Treatment ◽  
Grain Size ◽  
Minimum Weight ◽  
Isothermal Oxidation ◽  
Optical Microscope ◽  
Grain Structure ◽  
Treatment Result ◽  
Oxidation Test ◽  
Heat Treated ◽  
Average Grain Size

This research study was focused on the effect of heat treatment on the isothermal oxidation of Fe-33Ni-18Cr alloy at 1000 °C. The Fe-33Ni-18Cr alloy was undergone heat treatment at three different temperatures, namely 1000 °C, 1100 °C and 1200 °C for 3 hours soaking time followed by water quench to vary the grain size of the alloy. The heat-treated alloys was prepared for further isothermal oxidation test. The heat-treated alloys was ground by using several grit of silicon carbide papers as well as weighed by using analytical balance and measured by using Vernier caliper before the oxidation test. The heat-treated Fe-33Ni-18Cr alloys was isothermally oxidized at 1000 °C for 150 hours exposure time. The characterization of the oxidized samples was carried out using optical microscope and scanning electron microscope (SEM). The heat treatment result shows that, increasing the heat treatment temperature was increased the average grain size of the alloy. The kinetics of oxidation was followed the parabolic rate law which represent the diffusion-controlled oxide growth rate. Fine grain structure of 1000i-1000 sample shows minimum weight gain and lower oxidation rate compared to samples of 1000i-1100 and 1000i-1200. On the other hand, 1000i-1100 and 1000i-1200 samples indicate the formation of oxide spallation and crack propagation on the oxidized surface, respectively.

scholarly journals Comparison between diffraction contrast tomography and high-energy diffraction microscopy on a slightly deformed aluminium alloy

IUCrJ ◽  
2016 ◽  
Vol 3 (1) ◽  
pp. 32-42 ◽  
Author(s):  
Loïc Renversade ◽  
Romain Quey ◽  
Wolfgang Ludwig ◽  
David Menasche ◽  
Siddharth Maddali ◽  
...  
Keyword(s):  
Grain Size ◽  
High Energy ◽  
Grain Structure ◽  
Data Sets ◽  
Relative Deviation ◽  
Diffraction Contrast ◽  
Average Grain Size ◽  
The Mean ◽  
Diffraction Microscopy

The grain structure of an Al–0.3 wt%Mn alloy deformed to 1% strain was reconstructed using diffraction contrast tomography (DCT) and high-energy diffraction microscopy (HEDM). 14 equally spaced HEDM layers were acquired and their exact location within the DCT volume was determined using a generic algorithm minimizing a function of the local disorientations between the two data sets. The microstructures were then compared in terms of the mean crystal orientations and shapes of the grains. The comparison shows that DCT can detect subgrain boundaries with disorientations as low as 1° and that HEDM and DCT grain boundaries are on average 4 µm apart from each other. The results are important for studies targeting the determination of grain volume. For the case of a polycrystal with an average grain size of about 100 µm, a relative deviation of about ≤10% was found between the two techniques.

Surface Modification and its Influence on the Microstructure and Creep Resistance of Nickel Based Superalloy René 77 / Modyfikacja Powierzchniowa Oraz Jej Wpływ Na Mikrostrukture I Wytrzymałosc Na Pełzanie Odlewów Z Nadstopu Niklu Ren´E 77

2013 ◽  
Vol 58 (1) ◽  
pp. 95-98 ◽  
Author(s):  
M. Zielinska ◽  
J. Sieniawski
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Surface Modification ◽  
Turbine Blades ◽  
Processing Parameters ◽  
Grain Structure ◽  
Creep Tests ◽  
Cobalt Aluminate ◽  
Nickel Based Superalloy ◽  
Average Grain Size

Superalloy René 77 is very wide used for turbine blades, turbine disks of aircraft engines which work up to 1050°C. These elements are generally produced by the investment casting method. Turbine blades produced by conventional precision casting methods have coarse and inhomogeneous grain structure. Such a material often does not fulfil basic requirements, which concern mechanical properties for the stuff used in aeronautical engineering. The incorporation of controlled grain size improved mechanical properties. This control of grain size in the casting operation was accomplished by the control of processing parameters such as casting temperature, mould preheating temperature, and the use of grain nucleates in the face of the mould. For nickel and cobalt based superalloys, it was found that cobalt aluminate (CoAl2O4) has the best nucleating effect. The objective of this work was to determine the influence of the inoculant’s content (cobalt aluminate) in the surface layer of the ceramic mould on the microstructure and mechanical properties at high temperature of nickel based superalloy René 77. For this purpose, the ceramic moulds were made with different concentration of cobalt aluminate in the primary slurry was from 0 to 10% mass. in zirconium flour. Stepped and cylindrical samples were casted for microstructure and mechanical examinations. The average grain size of the matrix ( phase), was determined on the stepped samples. The influence of surface modification on the grain size of up to section thickness was considered. The microstructure investigations with the use of light microscopy and scanning electron microscopy (SEM) enable to examine the influence of the surface modification on the morphology of ’ phase and carbides precipitations. Verification of the influence of CoAl2O4 on the mechanical properties of castings were investigated on the basis of results obtained form creep tests.

Improvement of Strength and Ductility by Combining Static Recrystallization and Unique Heat Treatment in Co-20Cr-15W-10Ni Alloy for Stent Application

2021 ◽  
Vol 1016 ◽  
pp. 1503-1509
Author(s):  
Kosuke Ueki ◽  
Soh Yanagihara ◽  
Kyosuke Ueda ◽  
Masaaki Nakai ◽  
Takayoshi Nakano ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Grain Size ◽  
Static Recrystallization ◽  
High Strength ◽  
Small Variation ◽  
Grain Structure ◽  
Fine Grain ◽  
High Temperature Short Time ◽  
Average Grain Size ◽  
Strength And Ductility

The Co-20Cr-15W-10Ni (CCWN, mass%) alloy has excellent corrosion resistance and strength-ductility balance and is applied in almost all balloon-expandable stent platforms. To further reduce the invasiveness of stent placement, it is necessary to reduce the diameter of the stent. That is, both high strength and high ductility should be achieved while maintaining a low yield stress. In our previous studies, it was discovered that low-temperature heat-treatment (LTHT) at 873 K improves the elongation of the CCWN alloy. In this study, we focused on the grain refinement by swaging and static recrystallization to improve the strength of the alloy. The as-swaged alloy was recrystallized at 1373–1473 K for 100–300 s, followed by LTHT. A fine grain structure with an average grain size of 3–17 μm was obtained by static recrystallization. The η-phase (M12X-M6X type precipitates, M: metallic elements, X: C and/or N) formed during the recrystallization at 1373–1448 K. The alloys recrystallized at 1448 and 1473 K had a homogeneous structure with a small variation in the grain size. On the other hand, the alloys recrystallized at 1373 and 1423 K had an inhomogeneous structure in which fine and coarse grains were mixed. Both the strength and ductility of the CCWN alloy were improved by combining high-temperature short-time recrystallization and LTHT.

Effect of Warm Rolling on Microstructure and High Temperature Mechanical Behavior of a Nano-Structured Al-8Fe-2Mo-2V-1Zr Alloy

2005 ◽  
Vol 486-487 ◽  
pp. 411-414 ◽  
Author(s):  
Won Yong Kim ◽  
Jae Sung Park ◽  
Mok Soon Kim
Keyword(s):  
Particle Size ◽  
Grain Size ◽  
Elevated Temperatures ◽  
Hot Extrusion ◽  
Warm Rolling ◽  
Spray Forming ◽  
Grain Structure ◽  
Average Grain Size ◽  
Two Samples ◽  
Additional Process

Mechanical properties of a nano-structured Al-8Fe-2Mo-2V-1Zr alloy produced by spray forming and subsequent hot-extrusion at 420°C were investigated in terms of tensile test as a function of temperature. Warm rolling was adapted as an additional process to expect further refinement in microstructure. Well-defined equiaxed grain structure and finely distributed dispersoids with nano-scale in particle size were observed in the spray formed and hot extruded sample (as-received sample). The average grain size and particle size were measured to 500 nm and 50 nm, respectively. While it was found that warm rolling gives rise to precipitate fine dispersoids less than 10 nm without influencing the grain size of matrix phase, in the temperature range of RT∼150°C, distinguishable changes in ultimate tensile strength were not found between the as-received and warm-rolled samples. At elevated temperatures ranging from 350 to 550°C, warm-rolled sample showed a higher value of elongation than as-received one although similar values of elongation were observed between two samples at temperatures lower than 350°C.

scholarly journals Evaluation of Cryogenic Mechanical Properties of Resistance Seam-Welded Invar Alloy Sheet by Instrumented Indentation Test

2020 ◽  
Vol 8 (12) ◽  
pp. 1009
Author(s):  
Seunghun Choi ◽  
Jongho Won ◽  
Jung-Jun Lee ◽  
Hee-Keun Lee ◽  
Seong-Min Kim ◽  
...  
Keyword(s):  
Grain Size ◽  
Plastic Zone ◽  
Base Material ◽  
Indentation Test ◽  
Welding Current ◽  
Optical Microscope ◽  
Alloy Sheet ◽  
Invar Alloy ◽  
Instrumented Indentation ◽  
Average Grain Size

Invar alloy sheet was welded by resistance seam welding (RSW) with a constant electrode force and three different welding currents. Tensile properties were evaluated using instrumented indentation testing (IIT) with a spherical indenter and microstructure observations were obtained under an optical microscope. IIT performed on the base material at room temperature (RT) and −163 °C, a cryogenic temperature (CT), gave results in good agreement with those of tensile testing. The strength of each zone was higher in the order of heat-affected zone (HAZ) < weld nugget (WN) < base material (BM) because the amount of cold working was least in the BM, heavy metal elements and carbon vaporized during melting, and the WN was formed more tightly than the HAZ, effectively constraining the plastic zone generated by the indentation. As for the welding current, the nugget, which becomes larger and tighter as the current increases, more effectively constrained the plastic zone in the indentation, and this soon increased the strength. Generally, Invar is known to consist of single-phase austenite, and microstructure observations have confirmed that the average grain size is ordered as BM < HAZ < WN. Fan-like columnar grains developed in the direction of the temperature gradient, and equiaxed grains were observed near the BM. It was confirmed that the grain size in the WN also increases as the current is increased. Interestingly, the constraint effect with increasing nugget size was more important for strength than the grain size.

Investigating the Relationships Between Structures and Properties of Al Alloys Incorporated With Ti and Mg Inclusions

2016 ◽  
Vol 138 (3) ◽  
Author(s):  
Halil Ibrahim Kurt ◽  
Ibrahim H. Guzelbey ◽  
Serdar Salman ◽  
Razamzan Asmatulu ◽  
Mustafa Dere
Keyword(s):  
Solid Solution ◽  
Grain Size ◽  
Elevated Temperatures ◽  
Solidification Process ◽  
Optical Microscope ◽  
Industrial Applications ◽  
Al Alloys ◽  
Average Grain Size ◽  
Solidification Processes ◽  
Grain Size And Shape

This study investigates the influence of titanium (Ti) and magnesium (Mg) additions on aluminum (Al) alloys in order to evaluate the relationship between the structure and properties of the new alloys. The alloys obtained at elevated temperatures mainly consist of Al–2Mg–1Ti, Al–2Mg–3Ti, Al–4Mg–2Ti, and Al–6Mg–2Ti alloys, as well as α and τ solid solution phases of intermetallic structures. Microstructural analyses were performed using X-ray diffraction (XRD), optical microscope, and energy dispersive spectrometry (EDS) techniques. Test results show that the average grain size of the alloys decreased with the addition of Ti inclusions during the casting and solidification processes, and the smallest grain size was found to be 90 μm for the Al–6Mg–3Ti alloy. In addition, tensile properties of the Al–Mg–Ti alloys were initially improved and then worsened after the addition of higher concentrations of Ti. The highest tensile and hardness values of the alloys were Al–4Mg–2Ti (205 MPa) and Al–6Mg–3Ti (80 BHN). The primary reasons for having higher mechanical properties may be attributed to strengthening of the solid solution and refinement of the grain size and shape during the solidification process. For this study, the optimum concentrations of Ti and Mg added to the Al alloys were 4 and 2 wt.%, respectively. This study may be useful for field researchers to develop new classes of Al alloys for various industrial applications.

Influence of Grain Size on Mechanical Properties in a Fe-9Ni-12Mn-2.5Si-1.0C TWIP Steel

2011 ◽  
Vol 197-198 ◽  
pp. 655-661
Author(s):  
Ze Bin Yang ◽  
Ding Yi Zhu ◽  
Wei Fa Yi ◽  
Shu Mei Lin ◽  
Cheng Mei Du
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Strain Hardening ◽  
Twip Steel ◽  
Optical Microscope ◽  
Coarse Grained ◽  
Microstructure Observation ◽  
Transmission Electron ◽  
Average Grain Size

We investigate the influence of grain size on mechanical properties in a Fe-9Ni-12Mn-2.5Si-1.0C TWIP steel by unidirectional tensile. Meanwhile the microstructures of the TWIP steel were observed and analyzed by optical microscope (OM) and transmission electron microscope (TEM). The experimental results show that the TWIP steel’s yield strength and tensile strength decrease with the increasing of grain size, whereas the plasticity increases with it. When the average grain size reaches to 27μm, the tensile strength is 1080MPa, the elongation percentage is 77%, and the strength-plasticity product achieves the 83160MPa•%. Steel’s strain hardening rate can be changed from three-stage to four-stage with the increasing of grain sizes, the areas of strain hardening by twin deformation mechanism are expanded. Through the microstructure observation we found that, coarse-grained TWIP steel conducts to twinning formation, the high density twins can increase the alloy’s ductility by splitting the grain.

Sign in / Sign up

Export Citation Format

Share Document