Net flow generation in closed-loop valveless pumping

2020 ◽  
Vol 234 (11) ◽  
pp. 2126-2142 ◽  
Author(s):  
Christos Manopoulos ◽  
Sokrates Tsangaris ◽  
Dimitrios Mathioulakis
Keyword(s):  
Flow Rate ◽  
Closed Loop ◽  
Simultaneous Recording ◽  
Elastic Tube ◽  
Fluid Medium ◽  
Flexible Tube ◽  
Flow Generation ◽  
Valveless Pumping ◽  
Valveless Pump ◽  
Flexible Walls

Net flow generation in valveless pumping, met in many physiological applications and recently in micropumping devices, constitutes an open fluid dynamics issue due to the complex interaction between the fluid medium and the flexible walls of the pump. In the context of the present experimental work, the conditions of the net flow generation are examined in a closed-loop horizontal valveless pump, which consists of a rigid and an elastic tube of equal diameters and lengths, and a pincher that forces the liquid within the tube to oscillate at Reynolds and Womersley numbers up to 7800 and 48, respectively. Pinching off as well as at the mid-length of the pump flexible tube, net flow is generated at certain pinching frequencies for which details are presented based on simultaneous recording of the pressure at the two tube junctions, the flow rate and the displacement of the pincher. Pinching off the mid-length of the pump at low pinching frequencies, net flow rate is practically null due to the almost identical pressure waveforms at the tube junctions, which vary in phase with the pincher motion. However, close to the first natural frequency of the hydraulic loop, the reflection of the pressure waves at the tube junctions combined with their increased phase difference cause high axial pressure gradients, which when they increase simultaneously with the squeezing of the tube, net flow rate maximization occurs. Pinching at the flexible tube mid-length area, nonzero net flow rates can also be generated, the sign of which changes when the pincher mid-point crosses the tube mid-length without being nullified.

Impedance Induce Valve Pump in Closed Loop System

2013 ◽  
Vol 393 ◽  
pp. 747-752 ◽  
Author(s):  
M. Mazwan Mahat ◽  
M. Arif Sulaiman ◽  
Chee Sheng Ow ◽  
Rosnadiah Bahsan ◽  
N. Merlisa Ali ◽  
...  
Keyword(s):  
Flow Rate ◽  
Liquid Velocity ◽  
Supply Voltage ◽  
Volume Flow Rate ◽  
Elastic Tube ◽  
Closed Loop System ◽  
Flexible Tube ◽  
Impedance Pump ◽  
Pump Mechanism ◽  
Set Up

This paper summarises a study which aims to develop and analyze the performance of the valveless impedance pump. Mechanism of valveless impedance pump is to apply acoustic impedance mismatch in order to drive the flow and also consists of a flexible connection at the ends to the more rigid sections. Characteristics of liquid velocity and pressure at the pump base valveless impedance at various supply voltage and different frequencies have been discovered through experimentation. Secondly, this research also aims to discuss the effect volume flow rate (millitres / min) in the elastic tube impedance based on different parameters of the pump pinch. The variation of pinch location and pinch width are also available through the results of this study. This study begins with the design set up to use the software and followed by installing all equipment used for the experiments. Then, this study continues to get results and make an analysis of the impedance pump by experimentation. Results found that all the parameters used in this experiment affect the flow rate in the impedance pump. Additional experiments on the effect of the thickness of the flexible tube on the flow rate gave lower values when the flexible tube is relatively thicker.

Valveless Pump in Closed Loop Tube System

2014 ◽  
Vol 607 ◽  
pp. 561-564
Author(s):  
M. Mazwan Mahat ◽  
Izdihar Tharazi ◽  
Liyana Roslan ◽  
Mohd Fakrul Jasni
Keyword(s):  
Flow Rate ◽  
Supply Voltage ◽  
Volume Flow Rate ◽  
Research Work ◽  
Maximum Flow ◽  
Elastic Tube ◽  
Working Fluid ◽  
Future Design ◽  
Valveless Pump ◽  
Impedance Pump

This research work aims to identify the characteristic of flow in valveless impedance pump which uses acoustic impedance mismatch to drive flow. The experimental setup mainly focuses on the elastic section connected between two ends of rigid tube. Fluid flow rate resulting from the pumping mechanism were measured at different supply voltage. Meanwhile, the volume flow rate (ml / min) in the elastic tube section were also determined based upon different pinch location and width using water as a working fluid. In order to achieve these parameters quantification, the experimental test rig was designed and the set of equipments were successfully assembled. Then, the measured parameters resulting from the experiment of the impedance pump are presented in significant findings of four curves plots. It is found that the maximum flow rate occurred at voltage setting equal to 4 V. Significantly, results obtained could beneficial future design as a mimics model for novel Ventricular Assist Device use in cardiac patient as well as further explanation about the factor that influence the characteristic of valveless impedance pump.

scholarly journals Modelling an unconventional closed-loop deep borehole heat exchanger (DBHE): sensitivity analysis on the Newberry volcanic setting

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Hannah R. Doran ◽  
Theo Renaud ◽  
Gioia Falcone ◽  
Lehua Pan ◽  
Patrick G. Verdin
Keyword(s):  
Sensitivity Analysis ◽  
Heat Exchanger ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Energy Flow ◽  
Closed Loop ◽  
Working Fluid ◽  
Valuable Insight ◽  
Deep Borehole

AbstractAlternative (unconventional) deep geothermal designs are needed to provide a secure and efficient geothermal energy supply. An in-depth sensitivity analysis was investigated considering a deep borehole closed-loop heat exchanger (DBHE) to overcome the current limitations of deep EGS. A T2Well/EOS1 model previously calibrated on an experimental DBHE in Hawaii was adapted to the current NWG 55-29 well at the Newberry volcano site in Central Oregon. A sensitivity analysis was carried out, including parameters such as the working fluid mass flow rate, the casing and cement thermal properties, and the wellbore radii dimensions. The results conclude the highest energy flow rate to be 1.5 MW, after an annulus radii increase and an imposed mass flow rate of 5 kg/s. At 3 kg/s, the DBHE yielded an energy flow rate a factor of 3.5 lower than the NWG 55-29 conventional design. Despite this loss, the sensitivity analysis allows an assessment of the key thermodynamics within the wellbore and provides a valuable insight into how heat is lost/gained throughout the system. This analysis was performed under the assumption of subcritical conditions, and could aid the development of unconventional designs within future EGS work like the Newberry Deep Drilling Project (NDDP). Requirements for further software development are briefly discussed, which would facilitate the modelling of unconventional geothermal wells in supercritical systems to support EGS projects that could extend to deeper depths.

scholarly journals In situ measurement and closed-loop control for powder supply processes

2021 ◽  
Author(s):  
Philipp Peter Breese ◽  
Tobias Hauser ◽  
Daniel Regulin ◽  
Stefan Seebauer ◽  
Christian Rupprecht
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Closed Loop ◽  
In Situ Measurement ◽  
Closed Loop Control ◽  
Loop Control ◽  
Powder Feeder ◽  
Powder Mass

AbstractThe powder mass flow rate is one of the main parameters regarding the geometrical precision of built components in the additive manufacturing process of laser metal deposition. However, its accuracy, constancy, and repeatability over the course of the running process is not given. Reasons among others are the performance of the powder conveyors, the complex nature of the powder behavior, and the resulting issues with existing closed-loop control approaches. Additionally, a direct in situ measurement of the powder mass flow rate is only possible with intrusive methods. This publication introduces a novel approach to measure the current powder mass flow rate at a frequency of 125 Hz. The volumetric powder flow evaluation given by a simple optical sensor concept was transferred to a mass flow rate through mathematical dependencies. They were found experimentally for a nickel-based powder (Inconel 625) and are valid for a wide range of mass flow rates. With this, the dynamic behavior of a vibration powder feeder was investigated and a memory effect dependent on previous powder feeder speeds was discovered. Next, a closed-loop control with the received sensor signal was implemented. The concept as a whole gives a repeatable and accurate powder mass flow rate while being universally retrofittable and applicable. In a final step, the improved dynamic and steady performance of the powder mass flow rate with closed-loop control was validated. It showed a reduction of mean relative errors for step responses of up to 81% compared to the uncontrolled cases.

Influence of convective conditions on the peristaltic mechanism of power-law fluid through a slippery elastic porous tube with different waveforms

2019 ◽  
Vol 16 (2) ◽  
pp. 340-358 ◽  
Author(s):  
Manjunatha Gudekote ◽  
Rajashekhar Choudhari ◽  
Hanumesh Vaidya ◽  
Prasad K.V. ◽  
Viharika J.U.
Keyword(s):  
Power Law ◽  
Flow Rate ◽  
Velocity Slip ◽  
Elastic Tube ◽  
Slip Parameter ◽  
Convective Conditions ◽  
Power Law Fluid ◽  
Porous Tube ◽  
Content Type ◽  
Similarity Transformations

Purpose The purpose of this paper is to emphasize the peristaltic mechanism of power-law fluid in an elastic porous tube under the influence of slip and convective conditions. The effects of different waveforms on the peristaltic mechanism are taken into account. Design/methodology/approach The governing equations are rendered dimensionless using the suitable similarity transformations. The analytical solutions are obtained by using the long wavelength and small Reynold’s number approximations. The expressions for velocity, flow rate, temperature and streamlines are obtained and analyzed graphically. Furthermore, an application to flow through an artery is determined by using a tensile expression given by Rubinow and Keller. Findings The principal findings from the present model are as follows. The axial velocity increases with an expansion in the estimation of velocity slip parameter and fluid behavior index, and it diminishes for a larger value of the porous parameter. The magnitude of temperature diminishes with an expansion in the Biot number. The flux is maximum for trapezoidal wave and minimum for the triangular wave when compared with other considered waveforms. The flow rate in an elastic tube increases with an expansion in the porous parameter, and it diminishes with an increment in the slip parameter. The volume of tapered bolus enhances with increasing values of the porous parameter. Originality/value The current study finds the application in designing the heart-lung machine and dialysis machine. The investigation further gives a superior comprehension of the peristaltic system associated with the gastrointestinal tract and the stream of blood in small or microvessels.

scholarly journals An Intelligent Multi-Sensor Variable Spray System with Chaotic Optimization and Adaptive Fuzzy Control

Sensors ◽  
2020 ◽  
Vol 20 (10) ◽  
pp. 2954 ◽  
Author(s):  
Lepeng Song ◽  
Jinpen Huang ◽  
Xianwen Liang ◽  
Simon X. Yang ◽  
Wenjin Hu ◽  
...  
Keyword(s):  
Control System ◽  
Flow Rate ◽  
Rise Time ◽  
Closed Loop ◽  
Closed Loop Control ◽  
Loop Control ◽  
Adaptive Fuzzy ◽  
Spray System ◽  
Adjustment Time ◽  
Spray Droplets

During the variable spray process, the micro-flow control is often held back by such problems as low initial sensitivity, large inertia, large hysteresis, nonlinearity as well as the inevitable difficulties in controlling the size of the variable spray droplets. In this paper, a novel intelligent double closed-loop control with chaotic optimization and adaptive fuzzy logic is developed for a multi-sensor based variable spray system, where a Bang-Bang relay controller is used to speed up the system operation, and adaptive fuzzy nonlinear PID is employed to improve the accuracy and stability of the system. With the chaotic optimization of controller parameters, the system is globally optimized in the whole solution space. By applying the proposed double closed-loop control, the variable pressure control system includes the pressure system as the inner closed-loop and the spray volume system as the outer closed-loop. Thus, the maximum amount of spray droplets deposited on the plant surface may be achieved with the minimum medicine usage for plants. Multiple sensors (for example: three pressure sensors and two flow rate sensors) are employed to measure the system states. Simulation results show that the chaotic optimized controller has a rise time of 0.9 s, along with an adjustment time of 1.5 s and a maximum overshoot of 2.67% (in comparison using PID, the rise time is 2.2 s, the adjustment time is 5 s, and the maximum overshoot is 6.0%). The optimized controller parameters are programmed into the hardware to control the established variable spray system. The experimental results show that the optimal spray pressure of the spray system is approximately 0.3 MPa, and the flow rate is approximately 0.08 m3/h. The effective droplet rate is 89.4%, in comparison to 81.3% using the conventional PID control. The proposed chaotically optimized composite controller significantly improved the dynamic performance of the control system, and satisfactory control results are achieved.

Experimental Study on the Effect of Pinch Parameters and Fluid Viscosity to Flow in Closed Loop Impedance Pump

2014 ◽  
Vol 660 ◽  
pp. 932-936
Author(s):  
M. Mazwan Mahat ◽  
R.N. Izzati ◽  
Ilya Izyan Shahrul Azhar ◽  
Izdihar Tharazi
Keyword(s):  
Fluid Flow ◽  
Flow Rate ◽  
Supply Voltage ◽  
Maximum Flow ◽  
Elastic Tube ◽  
Fluid Viscosity ◽  
Ventricular Assist ◽  
Tube Section ◽  
Impedance Pump ◽  
Device Use

This paper aims to analyse the performance of impedance pump that uses energy mismatch to drive fluid flow. The experimental setup mainly focus to establish the relationship between the fluids flow rates in elastic tube section connected between two ends of solid tube and pinch mechanism location as well as fluid viscosity. Measurement of fluid flow rate or representation of its velocities resulting from the pumping mechanism is measured using two different supply voltage and constant pincher width. These measured parameters resulting from the pinch mechanism of the elastic tube section were varied at different pinch location along itsx-axis direction; divided into two main cases namely (1) 2 V and (2) 3 V at 40 mm to 140 mm pinch location. From the voltage variation, it is found that the maximum flow rate given by voltage 3.0 V at pinch location 40 mm while for the effect of viscosity, the highest flow rate is 93 ml/min. The profiles obtained revealed the characteristic of valve less pump to be the new model of new Ventricular Assist Device use in cardiac patient as well as further explanation about the factor that influence the characteristic of elastic tube.

Feedforward model-inverse position control of three-stage servo-valve using zero magnitude error tracking control

2018 ◽  
Vol 233 (7) ◽  
pp. 2340-2348 ◽  
Author(s):  
Kyeong Ha Lee ◽  
Seung Guk Baek ◽  
Hyouk Ryeol Choi ◽  
Hyungpil Moon ◽  
Sang-Hoon Ji ◽  
...  
Keyword(s):  
Flow Rate ◽  
Tracking Control ◽  
Closed Loop ◽  
Position Control ◽  
Control Method ◽  
Least Squares Method ◽  
Flow Direction ◽  
Recursive Least Squares ◽  
Servo Valve ◽  
Model Inverse

Three-stage servo-valves are popularly used in hydraulic systems that require large flow rate and high pressure. For a proper control of flow direction and flow rate fed into a hydraulic actuator, securing a proper position control bandwidth is a critical task for the servo-valve. In this paper, a set of popular control methods are systematically studied and a control method is selected. It is proven that the feedforward model-inverse control is the most effective method in terms of the control bandwidth. In the present work, the feedforward closed-loop architecture is adopted and the closed-loop system is estimated in a linear discrete-time transfer function by recursive least squares method. On recognizing a nonminimum phase zero problem, this work implements the zero magnitude error tracking control, an approximate model-inverse technique, in order to overcome the problem. As a result, the effectiveness of the proposed feedforward model-inverse position control strategy is verified.

Sign in / Sign up

Export Citation Format

Share Document