Enhancing output power of rotational electret energy harvester by synchronized switch harvesting on inductor

2021 ◽  
pp. 1045389X2110116
Author(s):  
Yiran Liu ◽  
Adrien Badel ◽  
Yuji Suzuki
Keyword(s):  
Power Dissipation ◽  
Energy Harvester ◽  
Series Resistance ◽  
Voltage Divider ◽  
Spice Simulation ◽  
Interface Circuit ◽  
Energy Harvesters ◽  
Bridge Rectifier ◽  
Nonlinear Interface ◽  
Good Agreement

A nonlinear interface circuit, known as synchronized switch harvesting on inductor (SSHI), for in-plane rotational electret kinetic energy harvesters (EHs) was developed. An explicit generator model is derived to verify the applicability of SSHI, which was originally proposed for the piezoelectric EH, on an in-plane electret EH. Experimentally, 505 μW was harvested with SSHI at a rectified voltage of 142 V for an in-plane rotational electret EH rotating at 1 rps, which is 2.47 times of that with a full-bridge rectifier, and which is in good agreement with the simulation result. The circuit efficiency and criteria for the inductor selection were clarified through circuit analysis based on spice simulation. It is found that the power dissipation of voltage-divider and rectification diodes becomes pronounced as the load voltage increases, constraining the efficiency. The inductor, which usually dominates the circuit volume, can be miniaturized for electret EHs, because the voltage inversion ratio, a benchmark of the SSHI performance, turns out to be insensitive to the series resistance of the inductor. The self-powering ability of the proposed circuit is also presented.

Sensors and energy harvesters based on (1–x)PMN-xPT piezoelectric ceramics

2019 ◽  
Vol 88 (1) ◽  
pp. 10901 ◽  
Author(s):  
Houda Lifi ◽  
Chouaib Ennawaoui ◽  
Abdelowahed Hajjaji ◽  
Samira Touhtouh ◽  
Said Laasri ◽  
...  
Keyword(s):  
Energy Harvester ◽  
Proof Mass ◽  
Piezoelectric Ceramics ◽  
Piezoelectric Bimorph ◽  
Mechanical Vibrations ◽  
Energy Harvesters ◽  
Hot Air ◽  
Simulation Results ◽  
Piezoelectric Performance ◽  
Good Agreement

With recent advancements in energy conversion mechanisms, piezoelectric ceramics (1–x)PbMg1/3 Nb2/3Ο3-xPbTiΟ3 (1–x)PMN-xPT have demonstrated their abilities for converting mechanical vibrations into electricity. Three (1–x)PMN-xPT compositions were used in the present work with (x = 0.25, 0.31 and 0.33). The purpose of this paper is to investigate their piezoelectric performance as generators for energy harvesting applications. The energy harvester is numerically analyzed in this work. It consists of a piezoelectric bimorph clamped at one end to vibrating machinery, and a proof mass mounted on its other end. The energy harvester is also analyzed and experimental measurements of the harvested power are compared to the simulation results. A good agreement was observed between the experimental and the simulations results. According the application to exploit the vibrations of a hot air extractor, the results show that the harvested energy density of solid ceramics (1–x)PMN-xPT is 0.043 W/m2.

Modeling and Experimental Verification of a Hybrid Energy Harvester Using Piezoelectric and Electromagnetic Technologies

2012 ◽  
Vol 569 ◽  
pp. 529-532 ◽  
Author(s):  
Zhen Long Xu ◽  
Xiao Xi Wang ◽  
Xiao Biao Shan ◽  
Tao Xie
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Experimental Results ◽  
Maximum Output ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Hybrid Energy Harvester ◽  
Theoretical Results ◽  
Good Agreement

This paper presents a hybrid energy harvester using piezoelectric (PZT) and electromagnetic (EM) technologies. A mathematical model of the output power for this generator was developed. Experiments were carried out to verify the numerical analysis. The theoretical results were in good agreement with the experimental results. The experimental results showed that the maximum output power of the separate PZT and EM energy harvesters were 0.667 mW and 0.32 mW, while that of the hybrid harvester was 0.845 mW under the vibration acceleration of 9.8 m/s2 at 66 Hz. It shows that the hybrid energy harvester can effectively increase the output power.

scholarly journals Compact Modelling of Electrical, Optical and Thermal Properties of Multi-Colour Power LEDs Operating on a Common PCB

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1286
Author(s):  
Krzysztof Górecki ◽  
Przemysław Ptak
Keyword(s):  
Integrated Circuits ◽  
Optical Model ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Junction Temperature ◽  
Optical Parameters ◽  
Spice Simulation ◽  
Light Emitting ◽  
Proposed Model ◽  
Good Agreement

This paper concerns the problem of modelling electrical, thermal and optical properties of multi-colour power light-emitting diodes (LEDs) situated on a common PCB (Printed Circuit Board). A new form of electro-thermo-optical model of such power LEDs is proposed in the form of a subcircuit for SPICE (Simulation Program with Integrated Circuits Emphasis). With the use of this model, the currents and voltages of the considered devices, their junction temperature and selected radiometric parameters can be calculated, taking into account self-heating phenomena in each LED and mutual thermal couplings between each pair of the considered devices. The form of the formulated model is described, and a manner of parameter estimation is also proposed. The correctness and usefulness of the proposed model are verified experimentally for six power LEDs emitting light of different colours and mounted on an experimental PCB prepared by the producer of the investigated devices. Verification was performed for the investigated diodes operating alone and together. Good agreement between the results of measurements and computations was obtained. It was also proved that the main thermal and optical parameters of the investigated LEDs depend on a dominant wavelength of the emitted light.

scholarly journals A Low Power AC/DC Interface for Wind-Powered Sensor Nodes

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1823
Author(s):  
Mohammad Haidar ◽  
Hussein Chible ◽  
Corrado Boragno ◽  
Daniele D. Caviglia
Keyword(s):  
Low Power ◽  
Power Supply ◽  
Energy Harvester ◽  
Optimization Techniques ◽  
Sensor Nodes ◽  
Wireless Sensor ◽  
Constant Voltage ◽  
Interface Circuit ◽  
Switching Converter ◽  
Input Signals

Sensor nodes have been assigned a lot of tasks in a connected environment that is growing rapidly. The power supply remains a challenge that is not answered convincingly. Energy harvesting is an emerging solution that is being studied to integrate in low power applications such as internet of things (IoT) and wireless sensor networks (WSN). In this work an interface circuit for a novel fluttering wind energy harvester is presented. The system consists of a switching converter controlled by a low power microcontroller. Optimization techniques on the hardware and software level have been implemented, and a prototype is developed for testing. Experiments have been done with generated input signals resulting in up to 67% efficiency for a constant voltage input. Other experiments were conducted in a wind tunnel that showed a transient output that is compatible with the target applications.

scholarly journals Load Resistance Optimization of a Broadband Bistable Piezoelectric Energy Harvester for Primary Harmonic and Subharmonic Behaviors

2021 ◽  
Vol 13 (5) ◽  
pp. 2865 ◽  
Author(s):  
Sungryong Bae ◽  
Pilkee Kim
Keyword(s):  
Energy Harvester ◽  
Load Resistance ◽  
Oscillation Period ◽  
Ambient Vibration ◽  
Ambient Vibrations ◽  
Frequency Dependency ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Bistable Energy Harvester

In this study, optimization of the external load resistance of a piezoelectric bistable energy harvester was performed for primary harmonic (period-1T) and subharmonic (period-3T) interwell motions. The analytical expression of the optimal load resistance was derived, based on the spectral analyses of the interwell motions, and evaluated. The analytical results are in excellent agreement with the numerical ones. A parametric study shows that the optimal load resistance depended on the forcing frequency, but not the intensity of the ambient vibration. Additionally, it was found that the optimal resistance for the period-3T interwell motion tended to be approximately three times larger than that for the period-1T interwell motion, which means that the optimal resistance was directly affected by the oscillation frequency (or oscillation period) of the motion rather than the forcing frequency. For broadband energy harvesting applications, the subharmonic interwell motion is also useful, in addition to the primary harmonic interwell motion. In designing such piezoelectric bistable energy harvesters, the frequency dependency of the optimal load resistance should be considered properly depending on ambient vibrations.

scholarly journals Power Density Improvement of Piezoelectric Energy Harvesters via a Novel Hybridization Scheme with Electromagnetic Transduction

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 803
Author(s):  
Zhongjie Li ◽  
Chuanfu Xin ◽  
Yan Peng ◽  
Min Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Power Density ◽  
Output Power ◽  
Energy Harvester ◽  
Hybrid Energy ◽  
Energy Harvesters ◽  
Piezoelectric Patch ◽  
Piezoelectric Energy ◽  
Electromagnetic Transduction ◽  
Self Powered ◽  
Power Densities

A novel hybridization scheme is proposed with electromagnetic transduction to improve the power density of piezoelectric energy harvester (PEH) in this paper. Based on the basic cantilever piezoelectric energy harvester (BC-PEH) composed of a mass block, a piezoelectric patch, and a cantilever beam, we replaced the mass block by a magnet array and added a coil array to form the hybrid energy harvester. To enhance the output power of the electromagnetic energy harvester (EMEH), we utilized an alternating magnet array. Then, to compare the power density of the hybrid harvester and BC-PEH, the experiments of output power were conducted. According to the experimental results, the power densities of the hybrid harvester and BC-PEH are, respectively, 3.53 mW/cm3 and 5.14 μW/cm3 under the conditions of 18.6 Hz and 0.3 g. Therefore, the power density of the hybrid harvester is 686 times as high as that of the BC-PEH, which verified the power density improvement of PEH via a hybridization scheme with EMEH. Additionally, the hybrid harvester exhibits better performance for charging capacitors, such as charging a 2.2 mF capacitor to 8 V within 17 s. It is of great significance to further develop self-powered devices.

Enhanced frequency synchronization for concurrent aeroelastic and base vibratory energy harvesting using a softening nonlinear galloping energy harvester

2021 ◽  
pp. 1045389X2110263
Author(s):  
Shun Chen ◽  
David Eager ◽  
Liya Zhao
Keyword(s):  
Energy Harvesting ◽  
Electromechanical Coupling ◽  
Energy Harvester ◽  
Poor Performance ◽  
Effective Bandwidth ◽  
Frequency Synchronization ◽  
Periodic Oscillations ◽  
Energy Harvesters ◽  
Paper Form ◽  
Excited Oscillation

This paper proposes a softening nonlinear aeroelastic galloping energy harvester for enhanced energy harvesting from concurrent wind flow and base vibration. Traditional linear aeroelastic energy harvesters have poor performance with quasi-periodic oscillations when the base vibration frequency deviates from the aeroelastic frequency. The softening nonlinearity in the proposed harvester alters the self-excited galloping frequency and simultaneously extends the large-amplitude base-excited oscillation to a wider frequency range, achieving frequency synchronization over a remarkably broadened bandwidth with periodic oscillations for efficient energy conversion from dual sources. A fully coupled aero-electro-mechanical model is built and validated with measurements on a devised prototype. At a wind speed of 5.5 m/s and base acceleration of 0.1 g, the proposed harvester improves the performance by widening the effective bandwidth by 300% compared to the linear counterpart without sacrificing the voltage level. The influences of nonlinearity configuration, excitation magnitude, and electromechanical coupling strength on the mechanical and electrical behavior are examined. The results of this paper form a baseline for future efficiency enhancement of energy harvesting from concurrent wind and base vibration utilizing monostable stiffness nonlinearities.

Performance analysis of a lever piezoelectric energy harvester for roadway applications

2021 ◽  
pp. 1045389X2110014
Author(s):  
Guangya Ding ◽  
Hongjun Luo ◽  
Jun Wang ◽  
Guohui Yuan
Keyword(s):  
Output Power ◽  
Energy Harvester ◽  
Open Circuit ◽  
Traffic Load ◽  
Energy Harvesters ◽  
Speed Sensor ◽  
Piezoelectric Energy ◽  
Optimal Load ◽  
Self Powered ◽  
Output Characteristics

A novel lever piezoelectric energy harvester (LPEH) was designed for installation in an actual roadway for energy harvesting. The model incorporates a lever module that amplifies the applied traffic load and transmits it to the piezoelectric ceramic. To observe the piezoelectric growth benefits of the optimized LPEH structure, the output characteristics and durability of two energy harvesters, the LPEH and a piezoelectric energy harvester (PEH) without a lever, were measured and compared by carrying out piezoelectric performance tests and traffic model experiments. Under the same loading condition, the open circuit voltages of the LPEH and PEH were 20.6 and 11.7 V, respectively, which represents a 76% voltage increase for the LPEH compared to the PEH. The output power of the LPEH was 21.51 mW at the optimal load, which was three times higher than that of the PEH (7.45 mW). The output power was linearly dependent on frequency and load, implying the potential application of the module as a self-powered speed sensor. When tested during 300,000 loading cycles, the LPEH still exhibited stable structural performance and durability.

Sign in / Sign up

Export Citation Format

Share Document