Mesoscopic investigation of layered graded metallic foams under dynamic compaction

2018 ◽  
Vol 21 (14) ◽  
pp. 2081-2098 ◽  
Author(s):  
Jinhua Zhang ◽  
Yadong Zhang ◽  
Junyu Fan ◽  
Qin Fang ◽  
Yuan Long
Keyword(s):  
Impact Loading ◽  
Dynamic Properties ◽  
Three Dimensional ◽  
Metallic Foam ◽  
Layer By Layer ◽  
Metallic Foams ◽  
Mesoscopic Model ◽  
Layer Arrangement ◽  
Computed Tomography Images ◽  
Closed Cell

This article is aimed to reveal the dynamic response of layered graded metallic foam under impact loading using a three-dimensional mesoscopic model. First, a mesoscopic model for closed-cell metallic foam is proposed based on the X-ray computed tomography images. Second, a numerical analysis approach is presented and validated with test data. Third, it studies the dynamic behavior of the layered graded metallic foam under impact loading numerically. The metallic foam specimen is composed layer by layer. The porosity, which is a fraction of the voids volume over the total volume, is different with each other for the layers. Simulations are conducted to the specimen with increasing and decreasing porosity arrangement. Results show that the layer arrangement is critical to the dynamic properties. The mesoscopic deformation of cell walls and the energy absorption capability are also affected significantly. This article gives insights into the mechanical properties and mesoscopic deformation of layered graded metallic foam.

A 3D mesoscopic model for the closed-cell metallic foams subjected to static and dynamic loadings

2015 ◽  
Vol 82 ◽  
pp. 103-112 ◽  
Author(s):  
Qin Fang ◽  
Jinhua Zhang ◽  
Yadong Zhang ◽  
Hao Wu ◽  
Ziming Gong
Keyword(s):  
Metallic Foams ◽  
Mesoscopic Model ◽  
Closed Cell ◽  
Dynamic Loadings

Solidification Analysis of Density-Graded Closed-Cell Metallic Foam Under Constant Temperature Boundary Condition

2016 ◽  
Author(s):  
W. B. Wang ◽  
X. H. Yang ◽  
Q. C. Zhang ◽  
T. J. Lu
Keyword(s):  
Boundary Condition ◽  
Constant Temperature ◽  
Solidification Front ◽  
Metallic Foam ◽  
Metallic Foams ◽  
Closed Cell ◽  
Temperature Boundary ◽  
Solidification Speed ◽  
Temperature Boundary Condition ◽  
Real Density

In the industrial fabrication processes of density-graded closed-cell metallic foams, it is of great importance to control the solidification immediately after foams are formed so as to obtain the final products with well distributed density-graded pores and less defects. This paper presented an analytical work aiming to predict the solidification front of density-graded metallic foam under constant temperature boundary condition. Numerical simulations based on ideal density-graded circular pores demonstrated good agreement with the analytical solutions. The 2D porous morphology of a real density-graded aluminum foam was further reconstructed with microCT, on the basis of which the propagation of solidification front inside this real density-graded foam was numerically investigated. An equivalent shape factor for this real foam was calculated to provide an insight for the influence of different pore shapes on solidification. Compared with other pores, the solidification speed of elliptical pores (a common pore shape in real foams) is moderate, i.e., slower than circular pores but quicker than triangular pores for same porosity.

scholarly journals Fast Overlap Detection between Hard-Core Colloidal Cuboids and Spheres. The OCSI Algorithm

Algorithms ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 72
Author(s):  
Luca Tonti ◽  
Alessandro Patti
Keyword(s):  
Colloidal Particles ◽  
Dynamic Properties ◽  
Wide Spectrum ◽  
Three Dimensional ◽  
Hard Core ◽  
Detection Algorithm ◽  
Three Dimensional Objects ◽  
Aggregation Behaviour ◽  
Sphere Radius ◽  
User Friendly

Collision between rigid three-dimensional objects is a very common modelling problem in a wide spectrum of scientific disciplines, including Computer Science and Physics. It spans from realistic animation of polyhedral shapes for computer vision to the description of thermodynamic and dynamic properties in simple and complex fluids. For instance, colloidal particles of especially exotic shapes are commonly modelled as hard-core objects, whose collision test is key to correctly determine their phase and aggregation behaviour. In this work, we propose the Oriented Cuboid Sphere Intersection (OCSI) algorithm to detect collisions between prolate or oblate cuboids and spheres. We investigate OCSI’s performance by bench-marking it against a number of algorithms commonly employed in computer graphics and colloidal science: Quick Rejection First (QRI), Quick Rejection Intertwined (QRF) and a vectorized version of the OBB-sphere collision detection algorithm that explicitly uses SIMD Streaming Extension (SSE) intrinsics, here referred to as SSE-intr. We observed that QRI and QRF significantly depend on the specific cuboid anisotropy and sphere radius, while SSE-intr and OCSI maintain their speed independently of the objects’ geometry. While OCSI and SSE-intr, both based on SIMD parallelization, show excellent and very similar performance, the former provides a more accessible coding and user-friendly implementation as it exploits OpenMP directives for automatic vectorization.

scholarly journals Design, Fabrication, and Testing of a Novel 3D 3-Fingered Electrothermal Microgripper with Multiple Degrees of Freedom

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 444
Author(s):  
Guoning Si ◽  
Liangying Sun ◽  
Zhuo Zhang ◽  
Xuping Zhang
Keyword(s):  
Degrees Of Freedom ◽  
Dynamic Properties ◽  
Three Dimensional ◽  
Polyimide Film ◽  
Zebrafish Embryos ◽  
Multiple Degrees Of Freedom ◽  
Electrothermal Actuator ◽  
3D Space ◽  
Pick And Place

This paper presents the design, fabrication, and testing of a novel three-dimensional (3D) three-fingered electrothermal microgripper with multiple degrees of freedom (multi DOFs). Each finger of the microgripper is composed of a V-shaped electrothermal actuator providing one DOF, and a 3D U-shaped electrothermal actuator offering two DOFs in the plane perpendicular to the movement of the V-shaped actuator. As a result, each finger possesses 3D mobilities with three DOFs. Each beam of the actuators is heated externally with the polyimide film. The durability of the polyimide film is tested under different voltages. The static and dynamic properties of the finger are also tested. Experiments show that not only can the microgripper pick and place microobjects, such as micro balls and even highly deformable zebrafish embryos, but can also rotate them in 3D space.

scholarly journals 3D Printing of High Viscosity Reinforced Silicone Elastomers

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2239
Author(s):  
Nicholas Rodriguez ◽  
Samantha Ruelas ◽  
Jean-Baptiste Forien ◽  
Nikola Dudukovic ◽  
Josh DeOtte ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
New Technologies ◽  
Three Dimensional ◽  
High Viscosity ◽  
Layer By Layer ◽  
Silicone Elastomers ◽  
Uv Curable ◽  
Octet Truss ◽  
Tunable Mechanical Properties

Recent advances in additive manufacturing, specifically direct ink writing (DIW) and ink-jetting, have enabled the production of elastomeric silicone parts with deterministic control over the structure, shape, and mechanical properties. These new technologies offer rapid prototyping advantages and find applications in various fields, including biomedical devices, prosthetics, metamaterials, and soft robotics. Stereolithography (SLA) is a complementary approach with the ability to print with finer features and potentially higher throughput. However, all high-performance silicone elastomers are composites of polysiloxane networks reinforced with particulate filler, and consequently, silicone resins tend to have high viscosities (gel- or paste-like), which complicates or completely inhibits the layer-by-layer recoating process central to most SLA technologies. Herein, the design and build of a digital light projection SLA printer suitable for handling high-viscosity resins is demonstrated. Further, a series of UV-curable silicone resins with thiol-ene crosslinking and reinforced by a combination of fumed silica and MQ resins are also described. The resulting silicone elastomers are shown to have tunable mechanical properties, with 100–350% elongation and ultimate tensile strength from 1 to 2.5 MPa. Three-dimensional printed features of 0.4 mm were achieved, and complexity is demonstrated by octet-truss lattices that display negative stiffness.

scholarly journals Application of subject-specific adaptive mechanical loading for bone healing in a mouse tail vertebral defect

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Angad Malhotra ◽  
Matthias Walle ◽  
Graeme R. Paul ◽  
Gisela A. Kuhn ◽  
Ralph Müller
Keyword(s):  
Mechanical Loading ◽  
Bone Defect ◽  
Bone Healing ◽  
Three Dimensional ◽  
Patient Specific ◽  
Dependent Manner ◽  
Micro Computed Tomography ◽  
Computed Tomography Images ◽  
Bone Defect Healing ◽  
Subject Specific

AbstractMethods to repair bone defects arising from trauma, resection, or disease, continue to be sought after. Cyclic mechanical loading is well established to influence bone (re)modelling activity, in which bone formation and resorption are correlated to micro-scale strain. Based on this, the application of mechanical stimulation across a bone defect could improve healing. However, if ignoring the mechanical integrity of defected bone, loading regimes have a high potential to either cause damage or be ineffective. This study explores real-time finite element (rtFE) methods that use three-dimensional structural analyses from micro-computed tomography images to estimate effective peak cyclic loads in a subject-specific and time-dependent manner. It demonstrates the concept in a cyclically loaded mouse caudal vertebral bone defect model. Using rtFE analysis combined with adaptive mechanical loading, mouse bone healing was significantly improved over non-loaded controls, with no incidence of vertebral fractures. Such rtFE-driven adaptive loading regimes demonstrated here could be relevant to clinical bone defect healing scenarios, where mechanical loading can become patient-specific and more efficacious. This is achieved by accounting for initial bone defect conditions and spatio-temporal healing, both being factors that are always unique to the patient.

scholarly journals Immersive 3D virtual reality imaging in planning minimally invasive and complex adult cardiac surgery

2020 ◽  
Vol 1 (1) ◽  
pp. 62-70
Author(s):  
Amir H Sadeghi ◽  
Wouter Bakhuis ◽  
Frank Van Schaagen ◽  
Frans B S Oei ◽  
Jos A Bekkers ◽  
...  
Keyword(s):  
Computed Tomography ◽  
Virtual Reality ◽  
Cardiac Surgery ◽  
Heart Surgery ◽  
Preoperative Planning ◽  
Operating Time ◽  
Three Dimensional ◽  
Cardiothoracic Surgery ◽  
Planning Tool ◽  
Computed Tomography Images

Abstract Aims Increased complexity in cardiac surgery over the last decades necessitates more precise preoperative planning to minimize operating time, to limit the risk of complications during surgery and to aim for the best possible patient outcome. Novel, more realistic, and more immersive techniques, such as three-dimensional (3D) virtual reality (VR) could potentially contribute to the preoperative planning phase. This study shows our initial experience on the implementation of immersive VR technology as a complementary research-based imaging tool for preoperative planning in cardiothoracic surgery. In addition, essentials to set up and implement a VR platform are described. Methods Six patients who underwent cardiac surgery at the Erasmus Medical Center, Rotterdam, The Netherlands, between March 2020 and August 2020, were included, based on request by the surgeon and availability of computed tomography images. After 3D VR rendering and 3D segmentation of specific structures, the reconstruction was analysed via a head mount display. All participating surgeons (n = 5) filled out a questionnaire to evaluate the use of VR as preoperative planning tool for surgery. Conclusion Our study demonstrates that immersive 3D VR visualization of anatomy might be beneficial as a supplementary preoperative planning tool for cardiothoracic surgery, and further research on this topic may be considered to implement this innovative tool in daily clinical practice. Lay summary Over the past decades, surgery on the heart and vessels is becoming more and more complex, necessitating more precise and accurate preoperative planning. Nowadays, operative planning is feasible on flat, two-dimensional computer screens, however, requiring a lot of spatial and three-dimensional (3D) thinking of the surgeon. Since immersive 3D virtual reality (VR) is an upcoming imaging technique with promising results in other fields of surgery, we aimed in this study to explore the additional value of this technique in heart surgery. Our surgeons planned six different heart operations by visualizing computed tomography scans with a dedicated VR headset, enabling them to visualize the patient’s anatomy in an immersive and 3D environment. The outcomes of this preliminary study are positive, with a much more reality-like simulation for the surgeon. In such, VR could potentially be beneficial as a preoperative planning tool for complex heart surgery.

Total Wrist Arthroplasty Alignment and Its Potential Association with Clinical Outcomes

2021 ◽  
Author(s):  
Bardiya Akhbari ◽  
Kalpit N. Shah ◽  
Amy M. Morton ◽  
Janine Molino ◽  
Douglas C. Moore ◽  
...  
Keyword(s):  
Computed Tomography ◽  
Clinical Outcomes ◽  
Three Dimensional ◽  
Radial Component ◽  
Single Type ◽  
Radiographic Images ◽  
Computed Tomography Images ◽  
Total Wrist Arthroplasty ◽  
Flexion Extension ◽  
Wrist Arthroplasty

Abstract Purpose There is a lack of quantitative research that describes the alignment and, more importantly, the effects of malalignment on total wrist arthroplasty (TWA). The main goal of this pilot study was to assess the alignment of TWA components in radiographic images and compare them with measures computed by three-dimensional analysis. Using these measures, we then determined if malalignment is associated with range of motion (ROM) or clinical outcomes (PRWHE, PROMIS, QuickDash, and grip strength). Methods Six osteoarthritic patients with a single type of TWA were recruited. Radiographic images, computed tomography images, and clinical outcomes of the wrists were recorded. Using posteroanterior and lateral radiographs, alignment measurements were defined for the radial and carpal components. Radiographic measurements were validated with models reconstructed from computed tomography images using Bland–Altman analysis. Biplanar videoradiography (<1mm and <1 degree accuracy) was used to capture and compute ROM of the TWA components. Linear regression assessed the associations between alignment and outcomes. Results Radiographic measures had a 95% limit-of-agreement (mean difference ±  1.96 × SD) of 3 degrees and 3mm with three-dimensional values, except for the measures of the carpal component in the lateral view. In our small cohort, wrist flexion–extension and radial–ulnar deviation were correlated with volar–dorsal tilt and volar–dorsal offset of the radial component and demonstrated a ROM increase of 3.7 and 1.6 degrees per degree increase in volar tilt, and 10.8 and 4.2 degrees per every millimeter increase in volar offset. The carpal component's higher volar tilt was also associated with improvements in patient-reported pain. Conclusions We determined metrics describing the alignment of TWA, and found the volar tilt and volar offset of the radial component could potentially influence the replaced wrist's ROM. Clinical Relevance TWA component alignment can be measured reliably in radiographs, and may be associated with clinical outcomes. Future studies must evaluate its role in a larger cohort.

Sign in / Sign up

Export Citation Format

Share Document