scholarly journals Preparation and moisture management performance of double guide bar warp-knitted fabric based on special covering structure

2021 ◽  
Vol 16 ◽  
pp. 155892502110469
Author(s):  
Xinhua Liang ◽  
Xuliang Yu ◽  
Zhijia Dong ◽  
Honglian Cong

This article provides a knitting method for warp-knitted fabrics with good moisture management performance. By adjusting of the warp knitting machine (mainly the bar), the design of lay-up method of the yarn, the selection of the yarn, and the warp let-off tension, the yarn covering relationship has been adjusted. By using two kinds of fineness polyester DTY, cotton yarn and spandex, designing two kinds of warp-knitting structures, six different warp-knitted fabrics have been knitted. The moisture management performance of these knitted samples was compared and evaluated. The study found that the greater the difference between the inner yarn and the outer yarn, the better the moisture management ability of the fabric. Polyester DTY with 50D/14F on the inner side and polyester DTY with 75D/288F on the outer side have the best moisture management performance. The polyester DTY with 50D/14F on the inside and 9.83Tex cotton yarn on the outside have higher wetting time and absorption rate.

2021 ◽  
pp. 004051752098497
Author(s):  
Ning Mao ◽  
Xiaohong Qin ◽  
Liming Wang ◽  
Jianyong Yu

Wet comfort is a critical performance for fabrics, especially when human bodies release sweat in daily life. Despite excellent moisture absorption performance, cotton yarns are still limited in the moisture release/transfer ability. Here, based on a novel electrospinning technology, polyacrylonitrile and polystyrene (PS) electrospun nanofiber/cotton composite yarns were produced, respectively. Under fluorescence microscopic observation, electrospun fibers within the composite yarns showed a uniform distribution. As a result, these composite yarn-based knitted fabrics obtained a good water transport ability and a fast water evaporation rate. According to the moisture management test, PS electrospun nanofiber composite yarn-based fabrics exhibited a relatively high one-way transport index R (400%), claiming an enhanced moisture management performance. Finally, specific surface area tests and finite element analyses were used to analyze the water transport mechanism inside the yarns. The results proved that a small number of electrospun fibers played a predominant role in enhancing the moisture management ability of the composite yarns.


2016 ◽  
Vol 47 (5) ◽  
pp. 897-920 ◽  
Author(s):  
T Karthik ◽  
P Senthilkumar ◽  
R Murugan

The search for sustainable renewable source of fibre is the need of the hour for the textile industry. In this aspect, milkweed fibres are considered to be one of the potential fibre crops. Plated knit fabrics are designed and engineered with correct selection of fibre and yarn constituents in the distinct bottom and top layer (next to sin) can serve well for next-to-skin applications. In this research work, the potential application of milkweed/polyester plated knitted fabrics for next-to-skin end uses were analysed by changing the inner and outer layers of plated fabrics and with different polyester/milkweed blend proportion. From the results of various moisture management indices of plated knitted fabrics, it is observed that except polyester/polyester and polyester/60% milkweed samples, which are exhibited as water penetration fabric, all other samples are showed as moisture management fabric. The hydrophobic fibre (polyester) in the top layer and hydrophilic fibres (milkweed) in the bottom layer exhibits higher bottom absorption rate, bottom spreading speed and one-way liquid transport leading to higher overall moisture management index. By considering the moisture management indices and grades of various samples, it could be observed that the plated fabric made from 40% milkweed/polyester could be an efficient moisture management fabric when used in either-way compared with other fabrics. One-way analysis of variance carried out at 95% confidence level showed that the results are statistically significant. The pair wise strength and association between various moisture management indices was analysed using Pearson correlation coefficient and observed that one-way transport capacity and overall moisture management capacity was found to be positively and linearly related to each other.


2010 ◽  
Vol 123-125 ◽  
pp. 1247-1250
Author(s):  
Raul Manuel Esteves Sousa Fangueiro ◽  
Hélder Filipe da Cunha Soutinho ◽  
Carla Freitas

Blends of wool and moisture management fibres such as Coolmax and Finecool have been prepared to produce innovative yarns with specific functionalities. These yarns have been used to produce knitted fabrics and their performance was evaluated, including vertical and horizontal wicking. The influence of wool fibre proportion on the performance of each blend is analyzed. It is observed that the Coolmax based fabrics show the best capillarity performance, and the wool fibre based fabrics show lower water absorption performance.


2011 ◽  
Vol 6 (4) ◽  
pp. 155892501100600 ◽  
Author(s):  
Elena Onofrei ◽  
Ana Maria Rocha ◽  
André Catarino

This paper studies the influence of fabric's structure on the thermal and moisture management properties of knitted fabrics made of two types of yarns with thermo-regulating effect: Coolmax® and Outlast®. The main purpose of this study was the selection of the most adequate fabric, to be used in summer and winter sportswear. The results demonstrated that some properties, such as, thermal properties, diffusion ability, air and water vapor permeability are influenced by both raw material type and knitted structure parameters. Wicking ability is influenced to a greater extent by the knitted structure, while the drying ability is primarily determined by raw material and to a lesser extent by the knitted structure parameters. Outlast® fabrics are preferred candidates for warmer climate sportswear, particularly due to their lower thermal resistance, higher thermal conductivity and absorptivity, air and water vapor permeability. When considering sportswear for colder weather, Coolmax® based structures seem to be the best choice. These findings are an important tool in the design of a sportswear product tailored to the different body areas thermal and moisture management requirements.


2019 ◽  
Vol 19 (2) ◽  
pp. 97-103 ◽  
Author(s):  
Sajid Hussainn ◽  
Viera Glombikova ◽  
Nasrullah Akhtar ◽  
Adnan Mazari ◽  
Tariq Mansoor ◽  
...  

Abstract This study investigates the effect of material composition on moisture management properties. Fiber type has significant influence on the moisture management properties of knitted fabrics. In this article, single jerseys knitted fabric samples with different yarn compositions were prepared. Liquid moisture transportation properties including wetting time, absorption rate, spreading speed, one-way transportation capability, and OMMC were evaluated by Moisture Management Tester (MMT) and vertical wicking was evaluated using thermography system and image analysis. Knitted sample having fine cotton yarns with coolmax and micro denier multifilament polypropylene showed best liquid transportation properties. There is a strong co-relation between OMMC and accumulative oneway transport index with vertical wicking of knitted samples.


2017 ◽  
Vol 4 (3) ◽  
pp. 162
Author(s):  
D. B. Patel ◽  
K. J. Patel ◽  
P. D. Bharadia

Objective: The objective of present research work was to develop formulation of orodispersible tablets of Ivabradine HCl and evaluate it for different evaluation parameters.Methods: The tablets were prepared by direct compression method. The formulation of the tablets were evaluated before compression for characterization of flow properties and after compression for different parameters of orodispersible tablet formulation.Results: Ivabradine hydrochloride orodispersible tablets were developed with considerable increase in drug release as compared to marketed formulations; nine formulations were developed and studied. The difference in drug release values was found to be 100.88 ± 0.10 respectively. The drug was characterized according to different compendial methods, on the basis of identification by HPLC, pH, organoleptic properties and other tests. Parameters evaluated were within prescribed limits and indicated good free flowing properties. The F6 batch with disintegration time 21 ± 3.0 and dissolution 99.29% was selected as optimized formulation. This was compared with conventional marketed formulation and was found superior. Batch F6 was also subjected to stability studies for two months and was tested for its hardness, wetting time, disintegration time, drug contents and dissolution behaviour monthly.Conclusions: By appropriate selection of excipients, it was possible to develop orodispersible tablets of Ivabradine HCl.


2020 ◽  
Vol 7 (2) ◽  
pp. 34-41
Author(s):  
VLADIMIR NIKONOV ◽  
◽  
ANTON ZOBOV ◽  

The construction and selection of a suitable bijective function, that is, substitution, is now becoming an important applied task, particularly for building block encryption systems. Many articles have suggested using different approaches to determining the quality of substitution, but most of them are highly computationally complex. The solution of this problem will significantly expand the range of methods for constructing and analyzing scheme in information protection systems. The purpose of research is to find easily measurable characteristics of substitutions, allowing to evaluate their quality, and also measures of the proximity of a particular substitutions to a random one, or its distance from it. For this purpose, several characteristics were proposed in this work: difference and polynomial, and their mathematical expectation was found, as well as variance for the difference characteristic. This allows us to make a conclusion about its quality by comparing the result of calculating the characteristic for a particular substitution with the calculated mathematical expectation. From a computational point of view, the thesises of the article are of exceptional interest due to the simplicity of the algorithm for quantifying the quality of bijective function substitutions. By its nature, the operation of calculating the difference characteristic carries out a simple summation of integer terms in a fixed and small range. Such an operation, both in the modern and in the prospective element base, is embedded in the logic of a wide range of functional elements, especially when implementing computational actions in the optical range, or on other carriers related to the field of nanotechnology.


2020 ◽  
Vol 30 (Supplement_5) ◽  
Author(s):  
T M Mikkola ◽  
H Kautiainen ◽  
M Mänty ◽  
M B von Bonsdorff ◽  
T Kröger ◽  
...  

Abstract Purpose Mortality appears to be lower in family caregivers than in the general population. However, there is lack of knowledge whether the difference in mortality between family caregivers and the general population is dependent on age. The purpose of this study was to analyze all-cause mortality in relation to age in family caregivers and to study their cause-specific mortality using data from multiple Finnish national registers. Methods The data included all individuals, who received family caregiver's allowance in Finland in 2012 (n = 42 256, mean age 67 years, 71% women) and a control population matched for age, sex, and municipality of residence (n = 83 618). Information on dates and causes of death between 2012 and 2017 were obtained from the Finnish Causes of Death Register. Flexible parametric survival modeling and competing risk regression adjusted for socioeconomic status were used. Results The total follow-up time was 717 877 person-years. Family caregivers had lower all-cause mortality than the controls over the follow-up (8.1% vs. 11.6%) both among women (hazard ratio [HR]: 0.64, 95% CI: 0.61-0.68) and men (HR: 0.73, 95% CI: 0.70-0.77). Younger adult caregivers had equal or only slightly lower mortality than their controls, but after age 60, the difference increased markedly resulting in over 10% lower mortality in favor of the caregivers in the oldest age groups. Caregivers had lower mortality for all the causes of death studied, namely cardiovascular, cancer, neurological, external, respiratory, gastrointestinal and dementia than the controls. Of these, the lowest was the risk for dementia (subhazard ratio=0.29, 95%CI: 0.25-0.34). Conclusions Older family caregivers have lower mortality than the age-matched controls from the general population while younger caregivers have similar mortality to their peers. This age-dependent advantage in mortality is likely to reflect selection of healthier individuals into the family caregiver role. Key messages The difference in mortality between family caregivers and the age-matched general population varies considerably with age. Advantage in mortality observed in family caregiver studies is likely to reflect the selection of healthier individuals into the caregiver role, which underestimates the adverse effects of caregiving.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yağmur Demircan Yalçın ◽  
Taylan Berkin Töral ◽  
Sertan Sukas ◽  
Ender Yıldırım ◽  
Özge Zorlu ◽  
...  

AbstractWe report the development of a lab-on-a-chip system, that facilitates coupled dielectrophoretic detection (DEP-D) and impedimetric counting (IM-C), for investigating drug resistance in K562 and CCRF-CEM leukemia cells without (immuno) labeling. Two IM-C units were placed upstream and downstream of the DEP-D unit for enumeration, respectively, before and after the cells were treated in DEP-D unit, where the difference in cell count gave the total number of trapped cells based on their DEP characteristics. Conductivity of the running buffer was matched the conductivity of cytoplasm of wild type K562 and CCRF-CEM cells. Results showed that DEP responses of drug resistant and wild type K562 cells were statistically discriminative (at p = 0.05 level) at 200 mS/m buffer conductivity and at 8.6 MHz working frequency of DEP-D unit. For CCRF-CEM cells, conductivity and frequency values were 160 mS/m and 6.2 MHz, respectively. Our approach enabled discrimination of resistant cells in a group by setting up a threshold provided by the conductivity of running buffer. Subsequent selection of drug resistant cells can be applied to investigate variations in gene expressions and occurrence of mutations related to drug resistance.


2019 ◽  
Vol 9 (10) ◽  
pp. 2065 ◽  
Author(s):  
Jonguk Kim ◽  
Hafeezur Rehman ◽  
Wahid Ali ◽  
Abdul Muntaqim Naji ◽  
Hankyu Yoo

In extensively used empirical rock-mass classification systems, the rock-mass rating (RMR) and tunneling quality index (Q) system, rock-mass quality, and tunnel span are used for the selection of rock bolt length and spacing and shotcrete thickness. In both systems, the rock bolt spacing and shotcrete thickness selection are based on the same principle, which is used for the back-calculation of the rock-mass quality. For back-calculation, there is no criterion for the selection of rock-bolt-spacing-based rock-mass quality weightage and shotcrete thickness along with tunnel-span-based rock-mass quality weightage. To determine this weightage effect during the back-calculation, five weightage cases are selected, explained through example, and applied using published data. In the RMR system, the weightage effect is expressed in terms of the difference between the calculated and back-calculated rock-mass quality in the two versions of RMR. In the Q system, the weightage effect is presented in plots of stress reduction factor versus relative block size. The results show that the weightage effect during back-calculation not only depends on the difference in rock-bolt-spacing-based rock-mass quality and shotcrete along with tunnel-span-based rock-mass quality, but also on their corresponding values.


Sign in / Sign up

Export Citation Format

Share Document