Preparation, characterization and catalytic properties of yttrium-zirconium-pillared montmorillonite and their application in supported Ce catalysts

Clay Minerals ◽  
2015 ◽  
Vol 50 (2) ◽  
pp. 211-219 ◽  
Author(s):  
Bo Xue ◽  
Hongmei Guo ◽  
Lujie Liu ◽  
Min Chen
Keyword(s):  
Catalytic Activity ◽  
Ethyl Acetate ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Active Sites ◽  
Industrial Applications ◽  
High Catalytic Activity ◽  
Total Oxidation ◽  
Pillared Montmorillonite

AbstractA new yttrium-zirconium-pillared montmorillonite (Y-Zr-MMT), was synthesized, characterized and used as a Ce catalyst support. The Y-Zr-MMT is a good support for dispersing cerium active sites and it is responsible for the high activity in the total oxidation of acetone, toluene and ethyl acetate. The Y-Zr-MMT shows greater advantages than the conventional alumina/cordierite honeycomb supports such as large specific surface area, lower cost and easier preparation. Catalytic tests demonstrated that Ce/Y-Zr-MMT (Ce loading 8.0%) was the most active, with the total oxidation of acetone, toluene and ethyl acetate being achieved at 220, 300 and 220°C, respectively. The catalyst displayed better activity for the oxidation of acetone and ethyl acetate than a conventional, supported Pd-catalyst under similar conditions. The special structure of the yttrium-doped zirconium-pillared montmorillonite can strengthen the interaction between the CeO2 and Zr-MMT support and improve the dispersion of the Ce particles, which enhances the catalytic activity for the oxidation of VOCs. The new catalyst, 8.0%Ce/Y-Zr-MMT, could be promising for industrial applications due to its high catalytic activity and low cost. The support and the catalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET specific surface area measurements.

The Influence of Fe/Al Molar Ratio on Microreactor-Based Catalyst Preparation and Carbon Nanotube Preparation

2021 ◽  
Vol 1036 ◽  
pp. 130-136
Author(s):  
Ting Qun Tan ◽  
Lei Geng ◽  
Yan Lin ◽  
Yan He
Keyword(s):  
Carbon Nanotubes ◽  
Catalytic Activity ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Small Diameter ◽  
High Specific Surface Area ◽  
Detection Methods ◽  
Molar Ratio ◽  
High Catalytic Activity

In order to prepare carbon nanotubes with high specific surface area, small diameter, low resistivity, high purity and high catalytic activity, the Fe-Mo/Al2O3 catalyst was prepared based on the microreactor. The influence of different Fe/Al molar ratios on the catalyst and the carbon nanotubes prepared was studied through BET, SEM, TEM and other detection methods. Studies have shown that the pore structure of the catalyst is dominated by slit pores at a lower Fe/Al molar ratio. The catalytic activity is the highest when the Fe/Al molar ratio is 1:1, reaching 74.1%. When the Fe/Al molar ratio is 1:2, the catalyst has a higher specific surface area, the maximum pore size is 8.63 nm, and the four-probe resistivity and ash content of the corresponding carbon nanotubes are the lowest. The higher the proportion of aluminum, the higher the specific surface area of the catalyst and the carbon nanotubes, and the finer the diameter of the carbon nanotubes, which gradually tends to relax. The results show that when the Fe/Al molar ratio is 1:2, although the catalytic activity of the catalyst is not the highest, the carbon nanotubes prepared have the best performance.

scholarly journals Syngas Production via CO2 Reforming of Methane Over SrNiO3 and CeNiO3 Perovskites

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2928
Author(s):  
Naushad Ahmad ◽  
Fahad Alharthi ◽  
Manawwer Alam ◽  
Rizwan Wahab ◽  
Salim Manoharadas ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Active Sites ◽  
Catalyst Deactivation ◽  
Dry Reforming Of Methane ◽  
Volume Number ◽  
Syngas Production

The development of a transition-metal-based catalyst with concomitant high activity and stability due to its distinguishing characteristics, yielding an abundance of active sites, is considered to be the bottleneck for the dry reforming of methane (DRM). This work presents the catalytic activity and durability of SrNiO3 and CeNiO3 perovskites for syngas production via DRM. CeNiO3 exhibits a higher specific surface area, pore volume, number of reducible species, and nickel dispersion when compared to SrNiO3. The catalytic activity results demonstrate higher CH4 (54.3%) and CO2 (64.8%) conversions for CeNiO3, compared to 22% (CH4 conversion) and 34.7% (CO2 conversion) for SrNiO3. The decrease in catalytic activity after replacing cerium with strontium is attributed to a decrease in specific surface area and pore volume, and nickel active sites covered with strontium carbonate. The stability results reveal the deactivation of both the catalysts (SrNiO3 and CeNiO3) but SrNiO3 showed more deactivation than CeNiO3, as demonstrated by deactivation factors. The catalyst deactivation is mainly attributed to carbon deposition and these findings are verified by characterizing the spent catalysts.

scholarly journals High-Level Oxygen Reduction Catalysts Derived from the Compounds of High-Specific-Surface-Area Pine Peel Activated Carbon and Phthalocyanine Cobalt

Nanomaterials ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 3429
Author(s):  
Lei Zhao ◽  
Ziwei Lan ◽  
Wenhao Mo ◽  
Junyu Su ◽  
Huazhu Liang ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Active Sites ◽  
High Performance ◽  
Low Cost ◽  
Specific Area ◽  
High Specific Surface Area ◽  
High Catalytic Activity

Non-platinum carbon-based catalysts have attracted much more attention in recent years because of their low cost and outstanding performance, and are regarded as one of the most promising alternatives to precious metal catalysts. Activated carbon (AC), which has a large specific surface area (SSA), can be used as a carrier or carbon source at the same time. In this work, stable pine peel bio-based materials were used to prepare large-surface-area activated carbon and then compound with cobalt phthalocyanine (CoPc) to obtain a high-performance cobalt/nitrogen/carbon (Co-N-C) catalyst. High catalytic activity is related to increasing the number of Co particles on the large-specific-area activated carbon, which are related with the immersing effect of CoPc into the AC and the rational decomposed temperature of the CoPc ring. The synergy with N promoting the exposure of CoNx active sites is also important. The Eonset of the catalyst treated with a composite proportion of AC and CoPc of 1 to 2 at 800 °C (AC@CoPc-800-1-2) is 1.006 V, higher than the Pt/C (20 wt%) catalyst. Apart from this, compared with other AC/CoPc series catalysts and Pt/C (20 wt%) catalyst, the stability of AC/CoPc-800-1-2 is 87.8% in 0.1 M KOH after 20,000 s testing. Considering the performance and price of the catalyst in a practical application, these composite catalysts combining biomass carbon materials with phthalocyanine series could be widely used in the area of catalysts and energy storage.

Bifunctional electrocatalysts of MOF-derived Co–N/C on bamboo-like MnO nanowires for high-performance liquid- and solid-state Zn–air batteries

2018 ◽  
Vol 6 (20) ◽  
pp. 9716-9722 ◽  
Author(s):  
Ya-Nan Chen ◽  
Yibo Guo ◽  
Huijuan Cui ◽  
Zhaojun Xie ◽  
Xin Zhang ◽  
...  
Keyword(s):  
Catalytic Activity ◽  
Solid State ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Active Sites ◽  
High Performance ◽  
High Specific Surface Area ◽  
Bifunctional Electrocatalysts ◽  
Nanowire Structure

MnO@Co–N/C composites were fabricated with excellent bifunctional catalytic activity and outstanding performance for both liquid- and solid-state Zn–air batteries. The excellent electrocatalytic activities are attributed to the unique 1D nanowire structure with abundant Co–Nx active sites and a high specific surface area.

scholarly journals SrFe1−xSnxO3−δ nanoparticles with enhanced redox properties for catalytic combustion of benzene

2020 ◽  
Vol 10 (18) ◽  
pp. 6342-6349
Author(s):  
Kazutaka Hashimoto ◽  
Ryoichi Otomo ◽  
Yuichi Kamiya
Keyword(s):  
Catalytic Activity ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Catalytic Combustion ◽  
Redox Properties ◽  
Partial Substitution ◽  
High Catalytic Activity

A series of SrFe1−xSnxO3−δ showed high catalytic activity for benzene combustion. The partial substitution of Fe with Sn increased specific surface area and accelerated redox rates of Fe, resulting in the improvement of the catalytic activity.

scholarly journals Preparation of Palladium Nanoparticles Decorated Polyethyleneimine/Polycaprolactone Composite Fibers Constructed by Electrospinning with Highly Efficient and Recyclable Catalytic Performances

Catalysts ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 559 ◽  
Author(s):  
Cuiru Wang ◽  
Juanjuan Yin ◽  
Shiqi Han ◽  
Tifeng Jiao ◽  
Zhenhua Bai ◽  
...  
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Palladium Nanoparticles ◽  
Active Sites ◽  
Pd Nanoparticles ◽  
Solid Substrate ◽  
High Catalytic Activity ◽  
Efficient Catalyst ◽  
Highly Efficient

Nano-sized palladium nanoparticles showed high catalytic activity with severe limitations in catalytic field due to the tendency to aggregate. A solid substrate with large specific surface area is an ideal carrier for palladium nanoparticles. In present work, polyethyleneimine/polycaprolactone/Pd nanoparticles (PEI/PCL@PdNPs) composite catalysts were successfully designed and prepared by electrospinning and reduction methods using PEI/PCL elexctrospun fiber as carrier. The added PEI component effectively regulated the microscopic morphology of the PEI/PCL fibers, following a large number of pit structures which increased the specific surface area of the electrospun fibers and provided active sites for loading of the palladium particles. The obtained PEI/PCL@PdNPs catalysts for reductions of 4-nitrophenol (4-NP) and 2-nitroaniline (2-NA) exhibited extremely efficient, stable, and reusable catalytic performance. It was worth mentioning that the reaction rate constant of catalytic reduction of 4-NP was as high as 0.16597 s−1. Therefore, we have developed a highly efficient catalyst with potential applications in the field of catalysis and water treatment.

scholarly journals Simple Synthesis of Molybdenum Carbides from Molybdenum Blue Nanoparticles

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 873
Author(s):  
Natalia Gavrilova ◽  
Maria Myachina ◽  
Victor Nazarov ◽  
Valery Skudin
Keyword(s):  
Catalytic Activity ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Molybdenum Carbide ◽  
Synthesis Method ◽  
High Catalytic Activity ◽  
Molybdenum Blue ◽  
Molybdenum Carbides ◽  
Vis Spectroscopy

In recent years, much attention has been paid to the development of a new flexible and variable method for molybdenum carbide (Mo2C) synthesis. This work reports the applicability of nano-size clusters of molybdenum blue to molybdenum carbide production by thermal treatment of molybdenum blue xerogels in an inert atmosphere. The method developed made it possible to vary the type (glucose, hydroquinone) and content of the organic reducing agent (molar ratio R/Mo). The effect of these parameters on the phase composition and specific surface area of molybdenum carbides and their catalytic activity was investigated. TEM, UV–VIS spectroscopy, DTA, SEM, XRD, and nitrogen adsorption were performed to characterize nanoparticles and molybdenum carbide. The results showed that, depending on the synthesis conditions, variants of molybdenum carbide can be formed: α-Mo2C, η-MoC, or γ-MoC. The synthesized samples had a high specific surface area (7.1–203.0 m2/g) and meso- and microporosity. The samples also showed high catalytic activity during the dry reforming of methane. The proposed synthesis method is simple and variable and can be successfully used to obtain both Mo2C-based powder and supports catalysts.

Preparation of Fe/N co-doped hierarchical porous carbon nanosheets derived from chitosan nanofibers for high-performance supercapacitors

2021 ◽  
pp. 1-16
Author(s):  
Yaqi Yang ◽  
Ziqiang Shao ◽  
Feijun Wang
Keyword(s):  
Specific Surface ◽  
Specific Capacitance ◽  
Surface Area ◽  
Double Layer ◽  
Specific Surface Area ◽  
Porous Carbon ◽  
Active Sites ◽  
Transport Pathway ◽  
Carbon Nanosheets ◽  
Hierarchical Porous

Abstract Due to the low specific capacitance and small specific surface area of conventional carbon materials used as electrode materials for double-layer capacitors, the search for more ideal materials and ingenious preparation methods remains a major challenge. In this study, fractional porous carbon nanosheets were prepared by co-doping Fe and N with chitosan as nitrogen source. The advantage of this method is that the carbon nanosheets can have a large number of pore structures and produce a large specific surface area. The presence of Fe catalyzes the graphitization of carbon in the carbon layer during carbonization process, and further increases the specific surface area of the electrode material. This structure provides an efficient ion and electron transport pathway, which enables more active sites to participate in the REDOX reaction, thus significantly enhancing the electrochemical performance of SCs. The specific surface area of CS-800 is up to 1587 m2 g−1. When the current density is 0.5 A g−1, the specific capacitance of CS-800 reaches 308.84 F g−1, and remains 84.61 % of the initial value after 10,000 cycles. The Coulomb efficiency of CS-800 is almost 100 % after a long cycle, which indicates that CS-800 has more ideal double-layer capacitance and pseudo capacitance.

Three-dimensional graphene encapsulated hollow CoSe2-SnSe2 nanoboxes for high performance asymmetric supercapacitors

2022 ◽  
Author(s):  
Kainan Li ◽  
Ke Zheng ◽  
Zhifang Zhang ◽  
Kuan Li ◽  
Ziyao Bian ◽  
...  
Keyword(s):  
Electrochemical Performance ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Active Sites ◽  
Specific Capacity ◽  
Three Dimensional ◽  
Hollow Structure ◽  
Large Specific Surface Area ◽  
Composite Aerogel

Abstract Construction of metal selenides with a large specific surface area and a hollow structure is one of the effective methods to improve the electrochemical performance of supercapacitors. However, the nano-material easily agglomerates due to the lack of support, resulting in the loss of electrochemical performance. Herein, we successfully design a three-dimensional graphene (3DG) encapsulation-protected hollow nanoboxes (CoSe2-SnSe2) composite aerogel (3DG/CoSe2-SnSe2) via a co-precipitation method coupled with self-assembly route, followed by a high temperature selenidation strategy. The obtained aerogel possesses porous 3DG conductive network, large specific surface area and plenty of reactive active sites. It could be used as a flexible and binder-free electrode after a facile mechanical compression process, which provided a high specific capacitance of 460 F g-1 at 0.5 A g-1, good rate capability of 212.7 F g-1 at 10 A g-1, and excellent cycle stability due to the fast electron/ion transfer and electrolyte diffusion. With the as-prepared 3DG/CoSe2-SnSe2 as positive electrodes and the AC (activated carbon) as negative electrodes, an asymmetric supercapacitor (3DG/CoSe2-SnSe2//AC) was fabricated, which delivered a high specific capacity of 38 F g-1 at 1A g-1 and an energy density of 11.89 W h kg-1 at 749.9 W kg-1, as well as a capacitance retention of 91.1% after 3000 cycles. This work provides a new method for preparing electrode material.

Sign in / Sign up

Export Citation Format

Share Document