scholarly journals Simulation and modeling of ultrasonic pitch-catch through-tubing logging

Geophysics ◽  
2016 ◽  
Vol 81 (4) ◽  
pp. D383-D393 ◽  
Author(s):  
Erlend Magnus Viggen ◽  
Tonni Franke Johansen ◽  
Ioan-Alexandru Merciu
Keyword(s):  
Wave Packet ◽  
Time Evolution ◽  
Structural Integrity ◽  
Wave Packets ◽  
Element Model ◽  
Sealing Material ◽  
Petroleum Wells ◽  
Second Wave ◽  
Good Agreement ◽  
Leaky Lamb Wave

Cased petroleum wells must be logged to determine the bonding and hydraulic isolation properties of the sealing material and to determine the structural integrity status. Although ultrasonic pitch-catch logging in single-casing geometries has been widely studied and is commercially available, this is not the case for logging in double-casing geometries despite its increasing importance in plug and abandonment operations. It is therefore important to investigate whether existing logging tools can be used in such geometries. Using a finite-element model of a double-casing geometry with a two-receiver pitch-catch setup, we have simulated through-tubing logging, with fluid between the two casings. We found that there appears a cascade of leaky Lamb wave packets on both casings, linked by leaked wavefronts. By varying the geometry and materials in the model, we have examined the effect on the pulse received from the second wave packet on the inner casing, sometimes known as the third interface echo. The amplitude of this pulse was found to contain information on the bonded material in the outer annulus. Much stronger amplitude variations were found with two equally thick casings than with a significant thickness difference; relative thickness differences of up to one-third were simulated. Finally, we have developed a simple mathematical model of the wave packets’ time evolution to encapsulate and validate our understanding of the wave packet cascade. This model shows a more complex time evolution in the later wave packets than the exponentially attenuated primary packet, which is currently used for single-casing logging. This indicates that tools with more than two receivers, which could measure wave packets’ amplitude at more than two points along their time evolution, would be able to draw more information from these later packets. The model was validated against simulations, finding good agreement when the underlying assumptions of the model were satisfied.

scholarly journals Spin-Orbit Entanglement in Time Evolution of Radial Wave Packets in Hydrogenic Systems

2004 ◽  
Vol 11 (04) ◽  
pp. 401-409
Author(s):  
Marcin Turek ◽  
Piotr Rozmej
Keyword(s):  
Wave Packet ◽  
Time Evolution ◽  
Time Scale ◽  
Degrees Of Freedom ◽  
Wave Packets ◽  
Characteristic Time Scale ◽  
Radial Wave ◽  
Mean Values ◽  
Breathing Motion ◽  
Wave Packet Revival

Time evolution of radial wave packets built from the eigenstates of Dirac equation for a hydrogenic system is considered. Radial wave packets are constructed from the states of different n quantum numbers and the same lowest angular momentum. In general they exhibit a kind of breathing motion with dispersion and (partial) revivals. Calculations show that for some particular preparations of the wave packet one can observe interesting effects in spin motion, coming from inherent entanglement of spin and orbital degrees of freedom. These effects manifest themselves through some oscillations in the mean values of spin operators and through changes of spatial probability density carried by upper and lower components of the wave function. It is also shown that the characteristic time scale of predicted effects (called T ls ) is much smaller for radial wave packets than in other cases, reaching values comparable to (or even less than) the time scale for the wave packet revival.

Modeling and Study of the Influence of Sealing on a Solid Oxide Fuel Cell

2008 ◽  
Vol 5 (1) ◽  
Author(s):  
Zacharie Wuillemin ◽  
N. Autissier ◽  
A. Nakajo ◽  
M. Luong ◽  
J. Van herle ◽  
...  
Keyword(s):  
Computational Cost ◽  
Element Model ◽  
Repeat Element ◽  
Solid Oxide ◽  
Oxide Fuel ◽  
Local Overheating ◽  
Sealing Material ◽  
Computational Fluid Dynamics Cfd ◽  
Energy Equations ◽  
Good Agreement

The properties of sealing materials are important for the performance and reliability of solid oxide fuel cells (SOFCs). Even if the properties of a sealing material can be studied separately, it remains difficult to quantify the effect of an imperfect seal on the repeat-element behavior. In this study, simulation is used to investigate the effects of an imperfect seal behavior on the performance and reliability of SOFCs. Diffusion through the sealing material and inherent local combustion of fuel are added to the computational fluid dynamics (CFD) repeat-element model, which also allows us to compute the flow field, the electrochemical reactions, and the energy equations. The results are in good agreement with experiments. The zones of parasitic combustion and local overheating are well reproduced. Furthermore, the model predicts a risk of reoxidation under polarization that is well observed. The model also shows the necessity to take into account the diffusion transport for the development of compressive seal materials, hence verifying the hypotheses made by other groups. The modeling approach presented here, which includes the imperfections of components, allows us to reproduce experiments with good accuracy and gives a better understanding of degradation processes. With its reasonable computational cost, it is a powerful tool for a design of SOFC based on reliability.

Nonlinear interaction of wave packets

1979 ◽  
Vol 22 (1) ◽  
pp. 15-26 ◽  
Author(s):  
J. T. Mendonça
Keyword(s):  
Dielectric Properties ◽  
Wave Packet ◽  
Frequency Shift ◽  
Doppler Shift ◽  
Nonlinear Interaction ◽  
Faraday Effect ◽  
Wave Packets ◽  
Inverse Faraday Effect ◽  
Stationary Plasma ◽  
Second Wave

We study the frequency shift suffered by a wave packet propagating in a homogeneous and stationary plasma, when subjected to the influence of a second wave packet which nonlinearly changes the dielectric properties of the plasma. The opposite cases of an adiabatic frequency shift and a relativistic Doppler shift are discussed in detail. The contribution of the inverse Faraday effect to the adiabatic situation is also taken into account. The results might be relevant in the search for new generators in the sub-millimetre ranges and for the understanding of spectral transfers of energy in a plasma.

scholarly journals Fatigue Modeling and Numerical Analysis of Re-Filling Probe Hole of Friction Stir Spot Welded Joints in Aluminum Alloys

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2171
Author(s):  
Armin Yousefi ◽  
Ahmad Serjouei ◽  
Reza Hedayati ◽  
Mahdi Bodaghi
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Fatigue Life ◽  
Fatigue Strength ◽  
Fatigue Behavior ◽  
Element Model ◽  
Plastic Strain Amplitude ◽  
Friction Stir ◽  
Probe Hole ◽  
Good Agreement

In the present study, the fatigue behavior and tensile strength of A6061-T4 aluminum alloy, joined by friction stir spot welding (FSSW), are numerically investigated. The 3D finite element model (FEM) is used to analyze the FSSW joint by means of Abaqus software. The tensile strength is determined for FSSW joints with both a probe hole and a refilled probe hole. In order to calculate the fatigue life of FSSW joints, the hysteresis loop is first determined, and then the plastic strain amplitude is calculated. Finally, by using the Coffin-Manson equation, fatigue life is predicted. The results were verified against available experimental data from other literature, and a good agreement was observed between the FEM results and experimental data. The results showed that the joint’s tensile strength without a probe hole (refilled hole) is higher than the joint with a probe hole. Therefore, re-filling the probe hole is an effective method for structures jointed by FSSW subjected to a static load. The fatigue strength of the joint with a re-filled probe hole was nearly the same as the structure with a probe hole at low applied loads. Additionally, at a high applied load, the fatigue strength of joints with a refilled probe hole was slightly lower than the joint with a probe hole.

The Spectrum Segmentation Algorithm of Multimode Vibration Signal Based on Spectral Clustering

2011 ◽  
Vol 121-126 ◽  
pp. 2372-2376
Author(s):  
Dan Dan Wang ◽  
Yu Zhou ◽  
Qing Wei Ye ◽  
Xiao Dong Wang
Keyword(s):  
Wave Packet ◽  
Frequency Domain ◽  
Spectral Clustering ◽  
Clustering Algorithm ◽  
Wave Packets ◽  
Vibration Signal ◽  
Segmentation Algorithm ◽  
Frequency Curve ◽  
Macroscopic Observation ◽  
Spectral Clustering Algorithm

The mode peaks in frequency domain of vibration signal are strongly interfered by strong noise, causing the inaccuracy mode parameters. According to this situation, this paper comes up with the thought of mode-peak segmentation based on the spectral clustering algorithm. First, according to the concept of wave packet, the amplitude-frequency of vibration signal is divided into wave packets. Taking each wave packet as a sample of clustering algorithm, the spectral clustering algorithm is used to classify these wave packets. The amplitude-frequency curve of a mode peak becomes a big wave packet in macroscopic. The experiment to simulation signals indicates that this spectral clustering algorithm could accord with the macroscopic observation of mode segmentation effectively, and has outstanding performance especially in strong noise.

Creep-Fatigue Interaction Effects On Pressure-Reducing Valve Under Cyclic Thermo-Mechanical Loadings Using Direct Cyclic Method

2021 ◽  
Author(s):  
Nak-Kyun Cho ◽  
Youngjae Choi ◽  
Haofeng Chen
Keyword(s):  
High Temperature ◽  
Power Plant ◽  
Fatigue Failure ◽  
Material Properties ◽  
Structural Integrity ◽  
Direct Method ◽  
Element Model ◽  
Critical Loading ◽  
Creep Fatigue ◽  
Pressure Reducing Valve

Abstract Supercritical boiler system has been widely used to increase efficiency of electricity generation in power plant industries. However, the supercritical operating condition can seriously affect structural integrity of power plant components due to high temperature that causes degradation of material properties. Pressure reducing valve is an important component being employed within a main steam line of the supercritical boiler, which occasionally thermal-fatigue failure being reported. This research has investigated creep-cyclic plastic behaviour of the pressure reducing valve under combined thermo-mechanical loading using a numerical direct method known as extended Direct Steady Cyclic Analysis of the Linear Matching Method Framework (LMM eDSCA). Finite element model of the pressure-reducing valve is created based on a practical valve dimension and temperature-dependent material properties are applied for the numerical analysis. The simulation results demonstrate a critical loading component that attributes creep-fatigue failure of the valve. Parametric studies confirm the effects of magnitude of the critical loading component on creep deformation and total deformation per loading cycle. With these comprehensive numerical results, this research provides engineer with an insight into the failure mechanism of the pressure-reducing valve at high temperature.

Rigid-Plastic Impact of Single Angular Particles

2021 ◽  
Author(s):  
Sandeep Dhar
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Orientation Dependence ◽  
Particle Orientation ◽  
Rigid Plastic ◽  
Plastic Model ◽  
Model Predictions ◽  
Good Agreement ◽  
Angular Particles

The trajectory of an angular particle as it cuts a ductile target is, in general, complicated because of its dependence not only on particle shape, but also on particle orientation at the initial instant of impact. This orientation dependence has also made experimental measurement of impact parameters of single angular particles very difficult, resulting in a relatively small amount of available experimental data in the literature. The current work is focused on obtaining measurements of particle kinematics for comparison to rigid plastic model developed by Papini and Spelt. Fundamental mechanisms of material removal are identified, and measurements of rebound parameters and corresponding crater dimensions of single hardened steel particles launched against flat aluminium alloy targets are presented. Also a 2-D finite element model is developed and a dynamic analysis is performed to predict the erosion mechanism. Overall, a good agreement was found among the experimental results, rigid-plastic model predictions and finite element model predictions.

Contribution of Lamb wave modes in the formation of higher order modes cluster (HOMC) guided waves

2021 ◽  
pp. 095440622110424
Author(s):  
Z Abbasi ◽  
F Honarvar
Keyword(s):  
Finite Element ◽  
Wave Packet ◽  
Lamb Wave ◽  
Guided Waves ◽  
Element Model ◽  
Higher Order ◽  
Guided Wave ◽  
Cross Sectional ◽  
Higher Order Modes ◽  
Wave Modes

In recent years, Higher Order Modes Cluster (HOMC) guided waves have been considered for ultrasonic testing of plates and pipes. HOMC guided waves consist of higher order Lamb wave modes that travel together as a single nondispersive wave packet. The objective of this paper is to investigate the effect of frequency-thickness value on the contribution of Lamb wave modes in an HOMC guided wave. This is an important issue that has not been thoroughly investigated before. The contribution of each Lamb wave mode in an HOMC guided wave is studied by using a two-dimensional finite element model. The level of contribution of various Lamb wave modes to the wave cluster is verified by using a 2D FFT analysis. The results show that by increasing the frequency-thickness value, the order of contributing modes in the HOMC wave packet increases. The number of modes that comprise a cluster also increases up to a specific frequency-thickness value and then it starts to decrease. Plotting of the cross-sectional displacement patterns along the HOMC guided wave paths confirms the shifting of dominant modes from lower to higher order modes with increase of frequency-thickness value. Experimental measurements conducted on a mild steel plate are used to verify the finite element simulations. The experimental results are found to be in good agreement with simulations and confirm the changes observed in the level of contribution of Lamb wave modes in a wave cluster by changing the frequency-thickness value.

scholarly journals Mechanical Strength Study of a Cranial Implant Using Computational Tools

2022 ◽  
Vol 12 (2) ◽  
pp. 878
Author(s):  
Pedro O. Santos ◽  
Gustavo P. Carmo ◽  
Ricardo J. Alves de Sousa ◽  
Fábio A. O. Fernandes ◽  
Mariusz Ptak
Keyword(s):  
Structural Integrity ◽  
Mechanical Performance ◽  
Skull Fracture ◽  
Human Head ◽  
Element Model ◽  
Von Mises Stress ◽  
Cranial Implant ◽  
Von Mises ◽  
Two Parameters ◽  
The Brain

The human head is sometimes subjected to impact loads that lead to skull fracture or other injuries that require the removal of part of the skull, which is called craniectomy. Consequently, the removed portion is replaced using autologous bone or alloplastic material. The aim of this work is to develop a cranial implant to fulfil a defect created on the skull and then study its mechanical performance by integrating it on a human head finite element model. The material chosen for the implant was PEEK, a thermoplastic polymer that has been recently used in cranioplasty. A6 numerical model head coupled with an implant was subjected to analysis to evaluate two parameters: the number of fixation screws that enhance the performance and ensure the structural integrity of the implant, and the implant’s capacity to protect the brain compared to the integral skull. The main findings point to the fact that, among all tested configurations of screws, the model with eight screws presents better performance when considering the von Mises stress field and the displacement field on the interface between the implant and the skull. Additionally, under the specific analyzed conditions, it is observable that the model with the implant offers more efficient brain protection when compared with the model with the integral skull.

Sign in / Sign up

Export Citation Format

Share Document