scholarly journals OPTIMIZATION OF METHODS AND PARAMETERS OF PRE-START THERMAL PREPARATION OF THE ENGINE FOR STARTING DEPENDING ON THE AMBIENT TEMPERATURE

2022 ◽  
Vol 16 (4) ◽  
pp. 53-58
Author(s):  
Evgenii Potapov ◽  
Dmitriy Vahrameev ◽  
Stanislav Sinickiy ◽  
Vladimir Medvedev ◽  
Alexey Terentyev
Keyword(s):  
Diesel Engine ◽  
Ambient Temperature ◽  
Correction Factor ◽  
Compression Ratio ◽  
Theoretical Calculations ◽  
Operating Conditions ◽  
Engine Oil ◽  
Correction Coefficient ◽  
Reduced Pressure ◽  
Start Up

Due to the lack of a generally accepted methodology for calculating the starting processes of automotive diesel engines, today it is not possible to calculate their temperature parameters with a sufficient degree of accuracy during start-up, which determine the condition of a guaranteed start-up process. The main problem in applying theoretical calculations is that they take into account the compression ratio of the engine. But the compression ratio and the value of the actual pressure in the engine cylinders during the start-up are completely different indicators. The purpose of this work is to correct the generally accepted dependencies for determining the temperature parameters of a diesel engine by introducing a correction factor that takes into account the reduced pressure in the engine cylinders during start-up, as well as calculating the temperature parameters during start-up according to the proposed calculation method. The correction factor is determined experimentally and depends on the engine temperature. When applying the correction factor, it becomes possible to accurately calculate the temperature of the fuel-air mixture, which determines the possibility of a guaranteed start-up process and at the same time allows you to set the minimum necessary requirements for the means of thermal pre-start preparation. A group of graduate students and teachers (Izhevsk State Agricultural Academy and Kazan Agrarian University) conducted a number of practical studies on the basis of one of the leading agricultural enterprises of the Udmurt Republic JSC "Ilyich's Way". The MTZ-82 tractor was taken as the object of the study. The subject of the study was the launch of its D-243 engine at low temperatures in real operating conditions. The choice of this model of diesel engine is due to its wide application on tractors. The studies were carried out according to the approved test program, which consists in starting the D-243 engine of the MTZ-82 tractor at temperatures from - 30 ° C with an interval of 5 ° C to +5 ° C (engine temperature is equal to ambient temperature), as well as from +5 ° C to +90 ° C with an interval of 20 ° C (ambient temperature +20 ° C). Measurements were carried out to determine the amount of compression in the engine cylinders and the speed of rotation of the crankshaft at certain temperatures. The experiments were carried out using a starter charger that provides the full electric power of the diesel starter. As a result of the experimental work carried out, a change in the value of the correction coefficient from the engine temperature was established, and in accordance with the modified methodology of theoretical calculations, the values of the temperature of the fuel-air mixture at the end of the compression stroke of the diesel engine at start-up are given. It is established that the minimum required pre-start temperature of the diesel engine should be at least +5 ° C. Based on the results of the analysis of calculations, the directions of ensuring a guaranteed start of the diesel engine by simultaneously heating the coolant and engine oil are proposed. These requirements can be provided by a thermal storage system that does not require additional energy sources for its operation

scholarly journals Modification of a Direct Injection Diesel Engine in Improving the Ignitability and Emissions of Diesel–Ethanol–Palm Oil Methyl Ester Blends

Energies ◽  
2019 ◽  
Vol 12 (14) ◽  
pp. 2644 ◽  
Author(s):  
Norhidayah Mat Taib ◽  
Mohd Radzi Abu Mansor ◽  
Wan Mohd Faizal Wan Mahmood
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Ambient Temperature ◽  
Palm Oil ◽  
Compression Ratio ◽  
Direct Injection ◽  
Cetane Number ◽  
Engine Performance ◽  
Injection Timing ◽  
Injection Strategies

Blending diesel with biofuels, such as ethanol and palm oil methyl ester (PME), enhances the fuel properties and produces improved engine performance and low emissions. However, the presence of ethanol, which has a small cetane number and low heating value, reduces the fuel ignitability. This work aimed to study the effect of injection strategies, compression ratio (CR), and air intake temperature (Ti) modification on blend ignitability, combustion characteristics, and emissions. Moreover, the best composition of diesel–ethanol–PME blends and engine modification was selected. A simulation was also conducted using Converge CFD software based on a single-cylinder direct injection compression ignition Yanmar TF90 engine parameter. Diesel–ethanol–PME blends that consist of 10% ethanol with 40% PME (D50E10B40), D50E25B25, and D50E40B10 were selected and conducted on different injection strategies, compression ratios, and intake temperatures. The results show that shortening the injection duration and increasing the injected mass has no significant effect on ignition. Meanwhile, advancing the injection timing improves the ignitability but with weak ignition energy. Therefore, increasing the compression ratio and ambient temperature helps ignite the non-combustible blends due to the high temperature and pressure. This modification allowed the mixture to ignite with a minimum CR of 20 and Ti of 350 K. Thus, blending high ethanol contents in a diesel engine can be applied by advancing the injection, increasing the CR, and increasing the ambient temperature. From the emission comparison, the most suitable mixtures that can be operated in the engine without modification is D50E25B25, and the most appropriate modification on the engine is by increasing the ambient temperature at 350 K.

Effect of the altitude on the combustion characteristics of a low-compression-ratio diesel engine during the start-up process

2016 ◽  
Vol 231 (13) ◽  
pp. 1838-1847 ◽  
Author(s):  
Ze-chao Kan ◽  
Zhi-yuan Hu ◽  
Di-ming Lou ◽  
Zhi-yi Cao ◽  
Jie Cao
Keyword(s):  
Diesel Engine ◽  
Compression Ratio ◽  
Peak Pressure ◽  
Direct Injection ◽  
Test System ◽  
Combustion Characteristics ◽  
Indicated Mean Effective Pressure ◽  
Start Up ◽  
Combustion Duration ◽  
Intake Pressure

One of the ways to meet future emission standards for cars and to limit the peak pressure of a heavy-duty, highly supercharged diesel engine is to reduce the compression ratio. Nevertheless, complications appear because stringent limitations to a reduction in the diesel compression ratio are the start-up requirements, in particular at high altitudes. An experimental study was conducted on the effect of the altitude on the combustion characteristics during the start-up process of a direct-injection midspeed intercooled turbocharged diesel engine with a compression ratio of 14.25:1. Specialized testing was conducted on the low-compression-ratio diesel engine, the intake pressure and the exhaust pressure of which were controlled by a plateau simulation test system to simulate the conditions at altitudes of 0 m, 1000 m, 2000 m, 3000 m, 3750 m and 4500 m. The results indicated that the pressure in the cylinder was lower during the cranking period as the altitude increased and that this caused the ignition operation to become difficult at altitudes above 3000 m. The combustion characteristics are significantly impacted by altitudes above 2000 m. At an altitude of 0–1000 m, the curve pattern of the cycle cylinder pressure had mainly a single peak during the start-up period. When the altitude increased to 2000 m, twin peaks and afterburn appeared in the cycles. Misfire appeared during the start-up period when the altitude increased to 3000 m, the combustion instability increased and the average indicated mean effective pressure decreased rapidly. When the altitude increases, the cycle-to-cycle variations in the peak pressure increased during idle, the ignition and the crank angle position at 50% of the cumulative heat release rate were delayed and the combustion duration was extended.

scholarly journals Thermal Impact of Operating Conditions on the Performance of a Combined Cycle Gas Turbine

2012 ◽  
Vol 10 (4) ◽  
Author(s):  
Thamir K. Ibrahim ◽  
M.M. Rahman
Keyword(s):  
Ambient Temperature ◽  
Gas Turbine ◽  
Flow Rate ◽  
Compression Ratio ◽  
Combined Cycle ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Overall Efficiency

The combined cycle gas-turbine (CCGT) power plant is a highly developed technology which generates electrical power at high efficiencies. The first law of thermodynamics is used for energy analysis of the performance of the CCGT plant. The effects of varying the operating conditions (ambient temperature, compression ratio, turbine inlet temperature, isentropic compressor and turbine efficiencies, and mass flow rate of steam) on the performance of the CCGT (overall efficiency and total output power) were investigated. The programming of the performance model for CCGT was developed utilizing MATLAB software. The simulation results for CCGT show that the overall efficiency increases with increases in the compression ratio and turbine inlet temperature and with decreases in ambient temperature. The total power output increases with increases in the compression ratio, ambient temperature, and turbine inlet temperature. The peak overall efficiency was reached with a higher compression ratio and low ambient temperature. The overall efficiencies for CCGT were very high compared to the thermal efficiency of GT plants. The overall thermal efficiency of the CCGT quoted was around 57%; hence, the compression ratios, ambient temperature, turbine inlet temperature, isentropic compressor and turbine efficiencies, and mass flow rate of steam have a strong influence on the overall performance of the CCGT cycle.

scholarly journals Methodology for the numerical solution of problems in relation to the coil-type electric heat exchangers for heating fuel

2021 ◽  
Vol 1 (4) ◽  
pp. 45-54
Author(s):  
G.M. Krokhta ◽  
◽  
YE.N. Khomchenko ◽  
N.A. Usatykh ◽  
◽  
...  
Keyword(s):  
Diesel Engine ◽  
Operating Conditions ◽  
Industrial Complex ◽  
Fuel Temperature ◽  
Engine Operation ◽  
Incomplete Combustion ◽  
Ambient Temperatures ◽  
Start Up ◽  
Electric Heat ◽  
Agricultural Tractors

The specificity of the operating conditions of agricultural tractors in the agro-industrial complex requires the provision of reliable engine start at low ambient temperatures. Improving the starting qualities of a diesel engine and reducing incomplete combustion in the post-start period can be achieved by increasing the exergy of the air charge at the end of the compression stroke or increas-ing the exergy of the fuel injected into the combustion chamber. The purpose of the study is to re-duce the expenditure of exergy for prestarting a diesel engine, improve starting qualities and reduce incomplete combustion in the post-start period. To achieve this goal, the design of an electric heat exchanger was developed in the form of a coil from a high-pressure fuel line, into which a heating element is inserted. A method for calculating its main parameters was developed. Calculations showed that in order to ensure reliable start-up of a diesel engine in winter, it is necessary to heat the fuel in the nozzle to a temperature of 240 ° C in the thermal boost mode. A heater of about 98 Watts is required to reach this temperature within 270 seconds of priming. However, in order to maintain such a fuel temperature during the start-up process, it is necessary to make changes in the nozzle design in order to minimize heat losses into the walls of the fuel channel by applying a heat-insulating coating. With further engine operation in the post-start heating mode, the fuel temperature in the injector is reduced to 85-95 ° C.

scholarly journals The Emission Characteristics of a Diesel Engine During Start-Up Process at Different Altitudes

Energies ◽  
2019 ◽  
Vol 12 (18) ◽  
pp. 3556
Author(s):  
Liang Fang ◽  
Diming Lou ◽  
Zhiyuan Hu ◽  
Piqiang Tan
Keyword(s):  
Diesel Engine ◽  
Compression Ratio ◽  
Particle Diameter ◽  
Cold Start ◽  
Particulate Emissions ◽  
Heavy Duty ◽  
Voc Emissions ◽  
Start Up ◽  
Carbon Dioxide Co2 ◽  
Different Altitudes

With increasingly stringent emission regulations, the cold start emissions have become more important than ever. Using a low compression ratio is a feasible way to improve a heavy-duty engine’s efficiency and emissions. However, cold start performance restricts the development of this technology, especially at high altitudes. In response, we conducted a study of the emissions of a heavy-duty low-compression-ratio diesel engine during start-up process at different altitudes. A plateau simulation system controlled the inlet and exhaust pressure to create altitude environments of 0 m, 1000 m, 2000 m, 3000 m, 3750 m and 4500 m. The gas, particulate and volatile organic compound (VOC) emissions were analyzed with speed and cycle during the start-up process. The results indicated that cold start performance and combustion characteristics became worse as altitudes increased. The gas and particulate emissions of carbon monoxide (CO), carbon dioxide (CO2), total hydrocarbon (THC) and nitrous oxide (NOX) almost all increased as the engine speed and altitude increased, and was much higher than in idle conditions. The PN and PM emissions in each particle diameter also increased as the altitude increased, which was the same as the nucleation mode and the accumulation mode particles. VOC emissions were also measured, which increased during the start-up process as altitudes increased.

Cake Formation in Cross-Flow Microfiltration Systems

1992 ◽  
Vol 25 (10) ◽  
pp. 149-162 ◽  
Author(s):  
V. L. Pillay ◽  
C. A. Buckley
Keyword(s):  
Cross Flow ◽  
Operating Conditions ◽  
Waste Waters ◽  
Domestic Waste ◽  
Time Curve ◽  
Good Correspondence ◽  
Operating Variables ◽  
Start Up ◽  
Turbulent Flow Regime ◽  
Cake Formation

Cross-flow microfiltration (CFMF) has potentially wide application in the processing of industrial and domestic waste waters. Optimum design and operation of CFMF systems necessitates a knowledge of the characteristic system behaviour, and an understanding of the mechanisms governing this behaviour. This paper is a contribution towards the elucidation and understanding of the behaviour of a woven fibre CFMF operated in the turbulent flow regime. The characteristic flux-time curve and effects of operating variables on flux are presented for a limestone suspension cross-flow filtered in a 25 mm woven fibre tube. The phenomena contributing to the shape of the flux-time curve are discussed. A model of the mechanisms governing cake growth and limit is presented. Predicted steady-state fluxes show a notably good correspondence with experimentally measured values. It is also found that the flux may not be uniquely defined by the operating conditions, but may also be a function of the operating path taken to reach the operating point. This is of significance in the start-up and operation of CFMF units.

scholarly journals Applications of Biocatalysts for Sustainable Oxidation of Phenolic Pollutants: A Review

2021 ◽  
Vol 13 (15) ◽  
pp. 8620
Author(s):  
Sanaz Salehi ◽  
Kourosh Abdollahi ◽  
Reza Panahi ◽  
Nejat Rahmanian ◽  
Mozaffar Shakeri ◽  
...  
Keyword(s):  
Phenolic Compounds ◽  
Operating Conditions ◽  
Phenolic Pollutants ◽  
Petroleum Refinery Wastewater ◽  
Start Up ◽  
Low Concentrations ◽  
Effective Removal ◽  
Wide Range ◽  
Loading Effects ◽  
Spent Caustic

Phenol and its derivatives are hazardous, teratogenic and mutagenic, and have gained significant attention in recent years due to their high toxicity even at low concentrations. Phenolic compounds appear in petroleum refinery wastewater from several sources, such as the neutralized spent caustic waste streams, the tank water drain, the desalter effluent and the production unit. Therefore, effective treatments of such wastewaters are crucial. Conventional techniques used to treat these wastewaters pose several drawbacks, such as incomplete or low efficient removal of phenols. Recently, biocatalysts have attracted much attention for the sustainable and effective removal of toxic chemicals like phenols from wastewaters. The advantages of biocatalytic processes over the conventional treatment methods are their ability to operate over a wide range of operating conditions, low consumption of oxidants, simpler process control, and no delays or shock loading effects associated with the start-up/shutdown of the plant. Among different biocatalysts, oxidoreductases (i.e., tyrosinase, laccase and horseradish peroxidase) are known as green catalysts with massive potentialities to sustainably tackle phenolic contaminants of high concerns. Such enzymes mainly catalyze the o-hydroxylation of a broad spectrum of environmentally related contaminants into their corresponding o-diphenols. This review covers the latest advancement regarding the exploitation of these enzymes for sustainable oxidation of phenolic compounds in wastewater, and suggests a way forward.

Sign in / Sign up

Export Citation Format

Share Document