scholarly journals Performance of an agricultural engine using turbocharger and intercooler

2021 ◽  
Vol 29 ◽  
pp. 100-106
Author(s):  
Marcelo Silveira de Farias ◽  
José Fernando Schlosser ◽  
Giácomo Müller Negri ◽  
Leonardo Casali ◽  
Gilvan Moisés Bertollo ◽  
...  
Keyword(s):  
Fuel Consumption ◽  
Engine Performance ◽  
Specific Fuel Consumption ◽  
Engine Torque ◽  
Fuel Flow ◽  
Randomized Design ◽  
Completely Randomized Design ◽  
Agricultural Tractor ◽  
Original Configuration

This paper aimed to evaluate the effects of air and fuel supercharging in an agricultural engine. The analyzed variables consisted of torque, power, and specific fuel consumption. Tests were carried out using a dynamometer through the power take-off of an agricultural tractor. The experiment was carried out at a laboratory in a completely randomized design arranged under a two-factorial scheme, with three replications. Six engine configurations (natural aspiration, natural aspiration + service, turbocharger, turbocharger + service, turbocharger + intercooler, and turbocharger + service + intercooler) and 10 engine speeds (1,200, 1,300, 1,400, 1,500, 1,600, 1,700, 1,800, 1,900, 2,000, and 2,100 rpm) were evaluated. The turbocharger alone did not increase engine torque and power. The increase in fuel flow enhanced engine performance for the evaluated configurations. Turbocharger + service and turbocharger + service + intercooler configurations reduced specific fuel consumption by up to 10% and increased torque and power by approximately 30% compared to the original configuration (natural aspiration).

scholarly journals Air and fuel supercharge in the performance of a diesel cycle engine

2017 ◽  
Vol 47 (6) ◽  
Author(s):  
Marcelo Silveira de Farias ◽  
José Fernando Schlosser ◽  
Alfran Tellechea Martini ◽  
Gustavo Oliveira dos Santos ◽  
Javier Solis Estrada
Keyword(s):  
Fuel Consumption ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Supply System ◽  
Specific Fuel Consumption ◽  
Diesel Cycle ◽  
System Variables ◽  
Agricultural Tractor ◽  
Original Configuration ◽  
Engine Power

ABSTRACT: This paper aimed to evaluate the performance of a Diesel cycle engine, changing the configurations for the air and fuel supply system. Variables analyzed were torque, power, specific fuel consumption and thermal efficiency in four different engine configurations (aspirated, aspirated + service, turbocharged + service and turbocharged). For that, there were dynamometer experiments by power take-off of an agricultural tractor. The experimental outline used was entirely randomized, in a bifatorial design with three repetitions. Results indicated that the engine supercharge, compared to its original configuration, provided a significant increase of torque and power. Only the addition of turbo does not caused a significant effect in the engine performance. Application of turbocharger provides an improvement in the burning of the air/fuel mixture, which favors the increase of engine power and; consequently, reduced the specific fuel consumption.

scholarly journals Comparative study of alternative biofuels on aircraft engine performance

2016 ◽  
Vol 231 (8) ◽  
pp. 1509-1521 ◽  
Author(s):  
Muhammad Hanafi Azami ◽  
Mark Savill
Keyword(s):  
Fuel Consumption ◽  
Engine Performance ◽  
Aircraft Engine ◽  
Specific Fuel Consumption ◽  
Energy Crisis ◽  
Mixing Ratio ◽  
Heating Value ◽  
Fuel Flow ◽  
Lower Heating Value ◽  
Lower Heating

Aviation industries are vulnerable to the energy crisis and simultaneously posed environmental concerns. Proposed engine technology advancements could reduce the environmental impact and energy consumption. Substituting the source of jet fuel from fossil-based fuel to biomass-based fuel will help reduce emissions and minimize the energy crisis. The present paper addresses the analysis of aircraft engine performance in terms of thrust, fuel flow and specific fuel consumption at different mixing ratio percentages (20%, 40%, 50%, 60% and 80%) of alternative biofuel blends already used in flight test (Algae biofuel, Camelina biofuel and Jatropha biofuel) at different flight conditions. In-house computer software codes, PYTHIA and TURBOMATCH, were used for the analysis and modeling of a three-shaft high-bypass-ratio engine which is similar to RB211-524. The engine model was verified and validated with open literature found in the test program of bio-synthetic paraffinic kerosene in commercial aircraft. The results indicated that lower heating value had a significant influence on thrust, fuel flow and specific fuel consumption at every flight condition and at all mixing ratio percentages. Wide lower heating value differences between two fuels give a large variation on the engine performances. Blended Kerosene–Jatropha biofuel and Kerosene–Camelina biofuel showed an improvement on gross thrust, net thrust, reduction of fuel flow and specific fuel consumption at every mixing ratio percentage and at different flight conditions. Moreover, the pure alternative of Jatropha biofuel and Camelina biofuel gave much better engine performances. This was not the case for the Kerosene–Algae blended biofuel. This study is a crucial step in understanding the influence of different blended alternative biofuels on the performance of aircraft engines.

New Design of a Low Cost Small Engine Dynamometer for Engine Testing

2014 ◽  
Vol 699 ◽  
pp. 642-647 ◽  
Author(s):  
M.A. Ammar Alfaiz ◽  
M. Tahir Musthafah ◽  
Abu Bakar Rosli ◽  
M. Shahir Ali ◽  
Abdul Muhaimin
Keyword(s):  
Fuel Consumption ◽  
Low Cost ◽  
Pressure Gauge ◽  
Engine Performance ◽  
Control Valve ◽  
Angular Speed ◽  
Specific Fuel Consumption ◽  
Engine Torque ◽  
Engine Testing ◽  
Engine Power

This paper discusses the design and development of a low cost small engine dynamometer for engine testing to measure engine performance i.e. power, torque and specific fuel consumption. The data and result were achieved by using a small hydraulic engine dynamometer with specific considerations and standard followed in order to have good engine dynamometer. Small engine was used by coupling it with the hydraulic pump that come with the control valve and pressure gauge. Control valve was set to build back pressure inside the pumping area. When the engine starts, the pressure gauge will give a reading which can be used to calculate the engine torque. By using the engine torque, engine power can be obtained by multiplying the angular speed with engine torque. Specific fuel consumption can be defined, by dividing the brake engine power with the fuel rate. From the experiment data, the brake power of the single cylinder engine showed that it is almost similar to the specification given by the manufacturer. The low cost hydraulic engine dynamometer, which is less than RM 15,000 can be used to measure an engine performance. The engine power, torque, engine speed and air fuel ratio data can be achieved from our developed engine dynamometer.

Exergy analysis of a turboprop engine at different flight altitude and speeds using novel consideration

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Ali Dinc ◽  
Yousef Gharbia
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Exergy Efficiency ◽  
Specific Fuel Consumption ◽  
Flight Altitude ◽  
Fuel Flow ◽  
Turboprop Engine ◽  
Shaft Power ◽  
Two Parameters ◽  
The Relationship

Abstract In this study, exergy efficiency calculations of a turboprop engine were performed together with main performance parameters such as shaft power, specific fuel consumption, fuel flow, thermal efficiency etc., for a range of flight altitude (0–14 km) and flight speeds (0–0.6 Mach). A novel exergy efficiency formula was derived in terms of specific fuel consumption and it is shown that these two parameters are inversely proportional to each other. Moreover, a novel exergy efficiency and thermal efficiency relation was also derived. The relationship showed that these two parameters are linearly proportional to each other. Exergy efficiency of the turboprop engine was found to be in the range of 23–33%. Thermal efficiency of the turboprop engine was found to be around 25–35%. Exergy efficiency is higher at higher speeds and altitude where the specific fuel consumption is lower. Conversely, exergy efficiency of the engine is lower for lower speeds and altitude where the specific fuel consumption is higher.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Characteristics of Water-in-Diesel Emulsions in a Single Cylinder Compression Ignition Engine

2014 ◽  
Author(s):  
Teja Gonguntla ◽  
Robert Raine ◽  
Leigh Ramsey ◽  
Thomas Houlihan
Keyword(s):  
Fuel Consumption ◽  
Direct Injection ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Compression Ignition Engine ◽  
Oil Emulsion ◽  
Single Cylinder ◽  
Performance And Emission

The objective of this project was to develop both engine performance and emission profiles for two test fuels — a 6% water-in-diesel oil emulsion (DOE-6) fuel and a neat diesel (D100) fuel. The testing was performed on a single cylinder, direct-injection, water-cooled diesel engine coupled to an eddy current dynamometer. Output parameters of the engine were used to calculate Brake Specific Fuel Consumption (BSFC) and Engine Efficiency (η) for each test fuel. DOE-6 fuels generated a 24% reduction in NOX and a 42% reduction in Carbon Monoxide emissions over the tested operating conditions. DOE-6 fuels presented higher ignition delays — between 1°-4°, yielded 1%–12% lower peak cylinder pressures and produced up to 5.5% lower exhaust temperatures. Brake Specific Fuel consumption increased by 6.6% for the DOE-6 fuels as compared to the D100 fuels. This project is the first research done by a New Zealand academic institution on water-in-diesel emulsion fuels.

Optimization of Turbofan Propulsion Cycle Using a Genetic Algorithm

2010 ◽  
Author(s):  
Adel Ghenaiet
Keyword(s):  
Genetic Algorithm ◽  
Fuel Consumption ◽  
Pressure Ratio ◽  
Engine Performance ◽  
Optimization Procedure ◽  
Specific Fuel Consumption ◽  
High Mass ◽  
Design Parameters ◽  
Inlet Temperature ◽  
Simplifying Assumptions

This paper presents an evolutionary approach as the optimization framework to design for the optimal performance of a high-bypass unmixed turbofan to match with the power requirements of a commercial aircraft. The parametric analysis had the objective to highlight the effects of the principal design parameters on the propulsive performance in terms of specific fuel consumption and specific thrust. The design optimization procedure based on the genetic algorithm PIKAIA coupled to the developed engine performance analyzer (on-design and off-design) aimed at finding the propulsion cycle parameters minimizing the specific fuel consumption, while meeting the required thrusts in cruise and takeoff and the restrictions of temperatures limits, engine size and weight as well as pollutants emissions. This methodology does not use engine components’ maps and operates on simplifying assumptions which are satisfying the conceptual or early design stages. The predefined requirements and design constraints have resulted in an engine with high mass flow rate, bypass ratio and overall pressure ratio and a moderate turbine inlet temperature. In general, the optimized engine is fairly comparable with available engines of equivalent power range.

scholarly journals Control of Exhaust Emissions Using Piston Coating on Two-StrokeSI Engines with Gasoline Blends

2021 ◽  
Vol 8 (1) ◽  
pp. H16-H20
Author(s):  
A.V.N.S. Kiran ◽  
B. Ramanjaneyulu ◽  
M. Lokanath M. ◽  
S. Nagendra ◽  
G.E. Balachander
Keyword(s):  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Specific Fuel Consumption ◽  
Thermal Barrier ◽  
Piston Crown ◽  
Barrier Coating

An increase in fuel utilization to internal combustion engines, variation in gasoline price, reduction of the fossil fuels and natural resources, needs less carbon content in fuel to find an alternative fuel. This paper presents a comparative study of various gasoline blends in a single-cylinder two-stroke SI engine. The present experimental investigation with gasoline blends of butanol and propanol and magnesium partially stabilized zirconium (Mg-PSZ) as thermal barrier coating on piston crown of 100 µm. The samples of gasoline blends were blended with petrol in 1:4 ratios: 20 % of butanol and 80 % of gasoline; 20 % of propanol and 80 % of gasoline. In this work, the following engine characteristics of brake thermal efficiency (BTH), specific fuel consumption (SFC), HC, and CO emissions were measured for both coated and non-coated pistons. Experiments have shown that the thermal efficiency is increased by 2.2 % at P20. The specific fuel consumption is minimized by 2.2 % at P20. Exhaust emissions are minimized by 2.0 % of HC and 2.4 % of CO at B20. The results strongly indicate that the combination of thermal barrier coatings and gasoline blends can improve engine performance and reduce exhaust emissions.

scholarly journals Rancang Bangun dan Pengujian Penghalang Heliks sebagai Pencampur Udara-Biogas pada Motor Otto

2021 ◽  
Vol 8 (3) ◽  
pp. 89-96
Author(s):  
Herbert Hasudungan Siahaan ◽  
Armansyah H Tambunan ◽  
Desrial ◽  
Soni Solistia Wirawan
Keyword(s):  
Fuel Consumption ◽  
Performance Test ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Specific Fuel Consumption ◽  
Combustion Reaction ◽  
Otto Cycle ◽  
Direct Use ◽  
Engine Power

A helical barrier as air-biogas mixing device was designed and tested for direct use of biogas from digester in otto cycle generator set. Homogeneity of the air-fuel mixture can give better combustion reaction and increase engine power. The design was based on simulation, which shows that a 0.039 m length of helical barrier gave a 5% increase in power compared to non-helical barrier. Likewise, the simulations also showed that the helical barrier reduced specific fuel consumption (SFC) by 8%. Accordingly, the mixer with helical barrier was designed, and fabricated. Its performance test confirms the improvement resulted by using helical barriers as air-biogas mixer in the engine. The experiment showed that the power increased by 5% when using helical barrier, while SFC decreased by 4.5%. It is concluded that the helical barrier can increase the homogeneity of the mixture resulting in better engine performance. Besides, emissions produced from the engine using a helical barrier also decreased.

scholarly journals Performance of an agricultural engine using blends of diesel and ethanol

2016 ◽  
Vol 46 (7) ◽  
pp. 1200-1205 ◽  
Author(s):  
Javier Solis Estrada ◽  
José Fernando Schlosser ◽  
Marcelo Silveira de Farias ◽  
Fabrício Azevedo Rodrigues ◽  
Alfran Tellechea Martini ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Alternative Fuel ◽  
Specific Fuel Consumption ◽  
Ethanol Content ◽  
Hydrous Ethanol ◽  
Agricultural Tractor ◽  
Engine Power

ABSTRACT: This research evaluated the performance of a diesel engine in an agricultural tractor, using Diesel S500 (B5) and mixture with 3% (ED3), 6% (ED6), 9% (ED9), 12% (ED12) and 15% (ED15) of hydrous ethanol. Variables evaluated were the power, torque, specific fuel consumption, torque reserve, speed reserve and elasticity index of engine. Results indicated that using B5 and ED3 the values of torque and engine power not differ, in addition, with the ED3 the fuel consumption was lower than 5.92%. Using ED12, power has reduced in 2.97%, compared with B5, while their fuel consumption had no difference. With ED15, the power was lower 6.30% and the fuel consumption increase 3.77%, both compared with B5. Torque reserve value was increased with increasing the ethanol content in B5, reducing the speed reserve and elasticity index of engine. Ethanol in Diesel S500 (B5) can be used as an alternative fuel in agricultural tractor engines without presenting high changes in the performance, since the ethanol content is at low percentages, up to 12%.

Sign in / Sign up

Export Citation Format

Share Document