scholarly journals Performance of an agricultural engine using blends of diesel and ethanol

2016 ◽  
Vol 46 (7) ◽  
pp. 1200-1205 ◽  
Author(s):  
Javier Solis Estrada ◽  
José Fernando Schlosser ◽  
Marcelo Silveira de Farias ◽  
Fabrício Azevedo Rodrigues ◽  
Alfran Tellechea Martini ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Alternative Fuel ◽  
Specific Fuel Consumption ◽  
Ethanol Content ◽  
Hydrous Ethanol ◽  
Agricultural Tractor ◽  
Engine Power

ABSTRACT: This research evaluated the performance of a diesel engine in an agricultural tractor, using Diesel S500 (B5) and mixture with 3% (ED3), 6% (ED6), 9% (ED9), 12% (ED12) and 15% (ED15) of hydrous ethanol. Variables evaluated were the power, torque, specific fuel consumption, torque reserve, speed reserve and elasticity index of engine. Results indicated that using B5 and ED3 the values of torque and engine power not differ, in addition, with the ED3 the fuel consumption was lower than 5.92%. Using ED12, power has reduced in 2.97%, compared with B5, while their fuel consumption had no difference. With ED15, the power was lower 6.30% and the fuel consumption increase 3.77%, both compared with B5. Torque reserve value was increased with increasing the ethanol content in B5, reducing the speed reserve and elasticity index of engine. Ethanol in Diesel S500 (B5) can be used as an alternative fuel in agricultural tractor engines without presenting high changes in the performance, since the ethanol content is at low percentages, up to 12%.

scholarly journals Air and fuel supercharge in the performance of a diesel cycle engine

2017 ◽  
Vol 47 (6) ◽  
Author(s):  
Marcelo Silveira de Farias ◽  
José Fernando Schlosser ◽  
Alfran Tellechea Martini ◽  
Gustavo Oliveira dos Santos ◽  
Javier Solis Estrada
Keyword(s):  
Fuel Consumption ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Supply System ◽  
Specific Fuel Consumption ◽  
Diesel Cycle ◽  
System Variables ◽  
Agricultural Tractor ◽  
Original Configuration ◽  
Engine Power

ABSTRACT: This paper aimed to evaluate the performance of a Diesel cycle engine, changing the configurations for the air and fuel supply system. Variables analyzed were torque, power, specific fuel consumption and thermal efficiency in four different engine configurations (aspirated, aspirated + service, turbocharged + service and turbocharged). For that, there were dynamometer experiments by power take-off of an agricultural tractor. The experimental outline used was entirely randomized, in a bifatorial design with three repetitions. Results indicated that the engine supercharge, compared to its original configuration, provided a significant increase of torque and power. Only the addition of turbo does not caused a significant effect in the engine performance. Application of turbocharger provides an improvement in the burning of the air/fuel mixture, which favors the increase of engine power and; consequently, reduced the specific fuel consumption.

scholarly journals Effects of Different Biodiesel-Diesel Blend Fuel on Combustion and Emission Characteristics of a Diesel Engine

Processes ◽  
2021 ◽  
Vol 9 (11) ◽  
pp. 1984
Author(s):  
Yanhui Zhang ◽  
Yunhao Zhong ◽  
Jie Wang ◽  
Dongli Tan ◽  
Zhiqing Zhang ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Combustion Process ◽  
Kinetic Mechanism ◽  
Alternative Fuel ◽  
Specific Fuel Consumption ◽  
Biodiesel Fuel ◽  
Emission Characteristics ◽  
Brake Specific Fuel Consumption ◽  
Blend Fuel

In this paper, biodiesel was used as an alternative fuel to investigate the combustion and emission characteristics of a four-stroke diesel engine, in terms of cylinder pressure, heat release rate, cylinder temperature, brake thermal efficiency, brake specific fuel consumption, nitrogen oxide, soot, carbon monoxide, and hydrocarbon. Firstly, a diesel engine cylinder model was developed by AVL-Fire software coupled with CHEMKIN code to simulate the injection and combustion of biodiesel with a kinetic mechanism with 106 species and 263 reactions. Then, the simulation model was validated by experimental results under 100% and 50% load conditions and used to simulate the combustion process of a diesel engine fueled with pure diesel, biodiesel, and biodiesel–diesel blends with 10%, 20%, 30% biodiesel by volume, respectively. The results showed that the brake specific fuel consumption increased with the increase of mixed biodiesel ratio. The brake specific fuel consumptions of B10, B20 and B30 increased by 1.1%, 2.3% and 3.3%, respectively, compared with that of D100. The combustion and emission characteristics of the diesel engine are improved. Therefore, biodiesel can be used as an alternative fuel for the diesel engine. The diesel–biodiesel fuel can improve the combustion and emission characteristics of the diesel engine.

The Performance of a Common Rail Diesel Engine Fueled with Different Blending Ratio of Biodiesels at Different Altitudes

2013 ◽  
Vol 860-863 ◽  
pp. 1685-1689
Author(s):  
Ze Fei Tan ◽  
Li Zhong Shen ◽  
De Cai Jin ◽  
Yang Wen Bin Ou
Keyword(s):  
High Pressure ◽  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Common Rail ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Gas Temperature ◽  
Engine Power ◽  
High Pressure Common Rail

To study the effect of the biodiesel on the performance of the high pressure common rail diesel engine performance, a experiment is conducted about the high pressure common rail diesel engine uses diesel fuel and different blending ratio of biodiesels. The results show that with the rising of the altitude, the engine power and the brake specific fuel consumption reduce, exhaust gas temperature increases; At the same altitude, the engine fueled with different blending ratio of bio-diesel has higher brake specific fuel consumption in comparison with fueled engine, but it has lower power, with the increase in bio-diesel blending ratio, engine power, fuel consumption increase.

scholarly journals Effects of Different Diesel-Ethanol Dual Fuel Ratio on Performance and Emission Characteristics of Diesel Engine

Processes ◽  
2021 ◽  
Vol 9 (7) ◽  
pp. 1135
Author(s):  
Zhiqing Zhang ◽  
Jiangtao Li ◽  
Jie Tian ◽  
Guangling Xie ◽  
Dongli Tan ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Combustion Process ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Cylinder Pressure ◽  
Brake Thermal Efficiency ◽  
Performance And Emission ◽  
Blended Fuel ◽  
Engine Power

In this paper, a four-stroke engine diesel was employed to investigate the effects of different fuel mixture ratios of diesel and ethanol on engine performance and emission characteristics in terms of cylinder temperature, heat release rate, brake power, brake thermal efficiency, brake specific fuel consumption, and cylinder pressure. The corresponding simulation model of diesel engine was developed by AVL-Fire coupled CHEMKIN code, and an improved chemical kinetics mechanism containing 34 reactions and 19 species was employed to simulate the fuel spray process and combustion process. The simulation model was validated by experimental results under 100% and 50% load conditions and used to simulate the combustion process of diesel engine fueled with pure diesel and diesel–ethanol blends with 10%, 20%, and 30% ethanol by volume, respectively. The results showed that the increase of ethanol content in the blended fuel had a certain negative impact on the performance characteristic of diesel engine and significantly improved the emission characteristic of the engine. With the ethanol proportion in the blended fuel increased to 10%, 20%, and 30%, the brake thermal efficiency of the engine increased by 2.24%, 4.33%, and 6.37% respectively. However, the brake-specific fuel consumption increased by 1.56%, 3.49%, and 5.74% and the power decreased by 1.58%, 3.46%, and 5.54% respectively. In addition, with the ethanol proportion in the blended fuel increased to 10%, 20%, and 30%, the carbon monoxide emission decreased by 34.69%, 47.60%, and 56.58%, and the soot emission decreased by 7.83%, 15.24%, and 22.52% respectively. Finally, based on the combining fuzzy and grey correlation theory, nitrogen oxide emission has the highest correlation with engine power and brake-specific fuel consumption. The values reach 0.9103 and 0.8945 respectively. It shows that nitrogen oxide emission and cylinder pressure have a significant relationship on engine power and brake-specific fuel consumption.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

scholarly journals Rancang Bangun dan Pengujian Penghalang Heliks sebagai Pencampur Udara-Biogas pada Motor Otto

2021 ◽  
Vol 8 (3) ◽  
pp. 89-96
Author(s):  
Herbert Hasudungan Siahaan ◽  
Armansyah H Tambunan ◽  
Desrial ◽  
Soni Solistia Wirawan
Keyword(s):  
Fuel Consumption ◽  
Performance Test ◽  
Engine Performance ◽  
Fuel Mixture ◽  
Specific Fuel Consumption ◽  
Combustion Reaction ◽  
Otto Cycle ◽  
Direct Use ◽  
Engine Power

A helical barrier as air-biogas mixing device was designed and tested for direct use of biogas from digester in otto cycle generator set. Homogeneity of the air-fuel mixture can give better combustion reaction and increase engine power. The design was based on simulation, which shows that a 0.039 m length of helical barrier gave a 5% increase in power compared to non-helical barrier. Likewise, the simulations also showed that the helical barrier reduced specific fuel consumption (SFC) by 8%. Accordingly, the mixer with helical barrier was designed, and fabricated. Its performance test confirms the improvement resulted by using helical barriers as air-biogas mixer in the engine. The experiment showed that the power increased by 5% when using helical barrier, while SFC decreased by 4.5%. It is concluded that the helical barrier can increase the homogeneity of the mixture resulting in better engine performance. Besides, emissions produced from the engine using a helical barrier also decreased.

scholarly journals Effects of Specific Fuel Consumption and Exhaust Emissions of Four Stroke Diesel Engine with CuO/Water Nanofluid as Coolant

2017 ◽  
Vol 64 (1) ◽  
pp. 111-121 ◽  
Author(s):  
S. Senthilraja ◽  
KCK. Vijayakumar ◽  
R. Gangadevi
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Load Condition ◽  
Exhaust Emissions ◽  
Cuo Nanoparticles ◽  
Specific Fuel Consumption ◽  
Gas Temperature ◽  
Step Method ◽  
Series Of Experiments ◽  
Exhaust Gas Temperature

Abstract This article reports the effects of CuO/water based coolant on specific fuel consumption and exhaust emissions of four stroke single cylinder diesel engine. The CuO nanoparticles of 27 nm were used to prepare the nanofluid-based engine coolant. Three different volume concentrations (i.e 0.05%, 0.1%, and 0.2%) of CuO/water nanofluids were prepared by using two-step method. The purpose of this study is to investigate the exhaust emissions (NOx), exhaust gas temperature and specific fuel consumption under different load conditions with CuO/water nanofluid. After a series of experiments, it was observed that the CuO/water nanofluids, even at low volume concentrations, have a significant influence on exhaust emissions. The experimental results revealed that, at full load condition, the specific fuel consumption was reduced by 8.6%, 15.1% and 21.1% for the addition of 0.05%, 0.1% and 0.2% CuO nanoparticles with water, respectively. Also, the emission tests were concluded that 881 ppm, 853 ppm and 833 ppm of NOx emissions were observed at high load with 0.05%, 0.1% and 0.2% volume concentrations of CuO/water nanofluids, respectively.

Effects of Micro-Emulsion Fuels on the Performance and Emissions of Diesel Engine

2011 ◽  
Vol 236-238 ◽  
pp. 151-154 ◽  
Author(s):  
Jia Quan Wang ◽  
Ping Sun ◽  
Zhen Chen ◽  
De Qing Mei
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Specific Fuel Consumption ◽  
Performance And Emissions ◽  
Micro Emulsion ◽  
Effects Of Temperature ◽  
The Stability

The micro-emulsion fuels were prepared with complex surfactant, and the effects of temperature on the stability of these fuels were investigated. The engine performance and the emissions were studied when the engine was fueled with diesel and micro-emulsion diesel respectively. Results showed that when the engine was fueled with micro-emulsion diesel, the NOXand smoke emissions were decreased obviously and HC and CO emissions were increased slightly. Discounting of surfactant and water, the specific fuel consumption of micro-emulsion diesel was lower than those of diesel under any load at the speed of 2900r/min.

scholarly journals Effect of cetane improver addition into diesel fuel: Methanol mixtures on performance and emissions at different injection pressures

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 555-566 ◽  
Author(s):  
Feyyaz Candan ◽  
Murat Ciniviz ◽  
Ilker Ors
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Injection Pressure ◽  
Specific Fuel Consumption ◽  
Exhaust Emission ◽  
Brake Specific Fuel Consumption ◽  
Consumption Values ◽  
Smoke Opacity

In this study, methanol in ratios of 5-10-15% were incorporated into diesel fuel with the aim of reducing harmful exhaust gasses of Diesel engine, di-tertbutyl peroxide as cetane improver in a ratio of 1% was added into mixture fuels in order to reduce negative effects of methanol on engine performance parameters, and isobutanol of a ratio of 1% was used as additive for preventing phase separation of all mixtures. As results of experiments conducted on a single cylinder and direct injection Diesel engine, methanol caused the increase of NOx emission while reducing CO, HC, CO2, and smoke opacity emissions. It also reduced torque and power values, and increased brake specific fuel consumption values. Cetane improver increased torque and power values slightly compared to methanol-mixed fuels, and reduced brake specific fuel consumption values. It also affected exhaust emission values positively, excluding smoke opacity. Increase of injector injection pressure affected performances of methanol-mixed fuels positively. It also increased injection pressure and NOx emissions, while reducing other exhaust emissions.

Sign in / Sign up

Export Citation Format

Share Document