scholarly journals Experimental study of the adsorption of Zn2 + ions on Natural Calcium Carbonate

2019 ◽  
Vol 9 (1) ◽  
pp. 78-84
Author(s):  
Karima Abellaoui ◽  
Hassan EL Kafssaoui ◽  
Hakima Nassali ◽  
Otheman Amrhar ◽  
Mohammed S. Elyoubi ◽  
...  
Keyword(s):  
Kinetic Equation ◽  
Calcium Carbonate ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Adsorption Kinetic ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Solution Ph ◽  
Order Kinetic Equation

In this study, Natural Calcium Carbonate (NCC) that was characterised by X-ray diffraction has been used as an adsorbent in the removal of Zn2+, from aqueous solution by a batch adsorption technique. The effects of various experimental parameters such as solution PH, initial concentration of solution, contact time, adsorbent masses and stirring speed were investigated. The results showed that basic PH and the average stirring speed were favourable for the adsorption of Zn2+, and the adequate equilibrium time for the adsorption of Zn2+ onto Natural Calcium Carbonate was 80min. The experimental data were analysed by the linear form of Langmuir, Freundlich. Isotherm models and showed a good fit with the Langmuir isotherm model. Adsorption kinetic was studied using pseudo first order kinetic equation, second order kinetic equation. The adsorption kinetic followed the pseudo second order equation. 

scholarly journals Treatment of textile effluents by chloride-intercalated Zn-, Mg- and Ni-Al layered double hydroxides

2016 ◽  
Vol 7 (3) ◽  
pp. 307-318 ◽  
Author(s):  
F. Z. Mahjoubi ◽  
A. Khalidi ◽  
O. Cherkaoui ◽  
R. Elmoubarki ◽  
M. Abdennouri ◽  
...  
Keyword(s):  
Oxygen Demand ◽  
Freundlich Isotherm ◽  
Chloride Ions ◽  
Second Order ◽  
Cod Removal ◽  
Precipitation Method ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Solution Ph ◽  
Pseudo Second Order

This work involved the preparation, characterization and dyes removal ability of Zn-Al, Mg-Al and Ni-Al layered double hydroxide (LDH) minerals intercalated by chloride ions. The materials were synthetized by the co-precipitation method. X-ray diffraction, Fourier transform infrared, thermogravimetric-differential thermal analysis and transmission electron microscopy characterization exhibited a typical hydrotalcite structure for all the samples. Adsorption experiments for methyl orange were performed in terms of solution pH, contact time and initial dye concentration. Experimental results indicate that the capacity of dye uptake augmented rapidly within the first 60 min and then stayed practically the same regardless of the concentration. Maximum adsorption occurred with acidic pH medium. Kinetic data were studied using pseudo-first-order and pseudo-second-order kinetic models. Suitable correlation was acquired with the pseudo-second-order kinetic model. Equilibrium data were fitted to Langmuir and Freundlich isotherm models. The maximum Langmuir monolayer adsorption capacities were 2,758, 1,622 and 800 mg/g, respectively, for Zn-Al-Cl, Mg-Al-Cl and Ni-Al-Cl. The materials were later examined for the elimination of color and chemical oxygen demand (COD) from a real textile effluent wastewater. The results indicated that the suitable conditions for color and COD removal were acquired at pH of 5. The maximum COD removal efficiency from the effluent was noted as 92.84% for Zn-Al-Cl LDH.

scholarly journals Adsorption of Chromium Ions on Activated Carbon Produced from Cow Bones

2019 ◽  
Vol 20 (2) ◽  
pp. 23-32
Author(s):  
Marah Waleed Khalid ◽  
Sami D. Salman
Keyword(s):  
Surface Area ◽  
Kinetic Equations ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Raw Material ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Solution Ph ◽  
Chromium Ions ◽  
Pseudo Second Order

Due to the broad range uses of chromium for industrial purposes, besides its carcinogenic effect, an efficient, cost effective removal method should be obtained. In this study, cow bones as a cheap raw material were utilized to produce active carbon (CBAC) by physiochemical activation, which was characterized using: SEM to investigate surface morphology and BET to estimate the specific surface area. The best surface area of CBAC was 595.9 m2/gm which was prepared at 600 ᵒC activation temperature and impregnation ratio of 1:1.5. CBAC was used in aqueous chromium ions adsorption. The investigated factors and their ranges are: initial concentration (10-50 mg/L), adsorption time (30-300 min), temperature (20-50 ᵒC) and solution pH (2-11). Isotherm of adsorption and its kinetics were studied. The adsorption process was modeled statistically and was represented by an empirical model. Equilibrium data were fitted to the Langmuir and Freundlich isotherm models and the data best represented by Freundlich isotherm. Pseudo- first order and pseudo- second order kinetic equations were utilized to study adsorption kinetics, where chromium adsorption on CBAC fitted pseudo- second order fitted the data more adequately. The best removal efficiency was found to be 94.32%.

scholarly journals Adsorption of penicillin by decaffeinated tea waste

2015 ◽  
Vol 17 (3) ◽  
pp. 95-99 ◽  
Author(s):  
Parvin Gharbani ◽  
Ali Mehrizad ◽  
Ismail Jafarpour
Keyword(s):  
High Performance ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Solution Ph ◽  
First Order ◽  
Tea Waste ◽  
Main Factor

Abstract Removal of penicillin has been investigated using decaffeinated tea waste (DCTW). Decaffeination of tea waste was investigated using different methods. Results indicate that ozonation was the most effective process for removal of penicillin. Batch adsorption experiments were completed at various temperatures (20, 30, and 40°C), DCTW dosages (2, 4, 6, 8, and 10 g per 250 mL), penicillin concentrations (4, 10, and 14 mg/L), and pH (3, 7, and 10) conditions. Studies showed that adsorption reaches equilibrium within 40 min. The main factor affecting adsorption of penicillin was the solution pH, with maximum adsorption occurring at pH 3. Higher adsorbent dosages and lower penicillin concentrations also resulted in higher percentages of penicillin removal. Results show that data obeyed the pseudo-first-order kinetic and Freundlich isotherm models. This process proves that low-cost DCTW could be used as a high performance adsorbent for removing penicillin from aqueous solutions.

Preparation of graphite by thermal annealing of polyacrylamide precursor for adsorption of Cs(I) and Co(II) ions from aqueous solutions

2012 ◽  
Vol 90 (10) ◽  
pp. 843-850 ◽  
Author(s):  
H.S. Hassan ◽  
Elsayed K. Elmaghraby
Keyword(s):  
Aqueous Solutions ◽  
Freundlich Isotherm ◽  
Effect Of Temperature ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Equilibration Time ◽  
Thermodynamic Quantities ◽  
Order Kinetic ◽  
Solution Ph ◽  
Radical Chain

In the present work, graphite nanostructures are prepared by thermolysis of a prepared polyacrylamide gel. The gel was prepared by radical chain polymerization and the synthesis of the nanostructures was done by step annealing at different temperatures. The structural of the prepared materials was studied by X-ray diffraction (XRD). The presence of carboxylic and phenolic functional groups on the graphite surface was confirmed by FT-IR analysis. Batch adsorption experiments were conducted to study the effect of equilibration time, initial metal cation concentration, and solution pH for the removal of Cs(I) and Co(II) from aqueous solutions. Kinetic data of Cs(I) adsorption was found to be well fitted with a pseudo-first-order kinetic model. The obtained isotherm data were correlated with the Langumir and Freundlich isotherm models. The effect of temperature on the equilibrium distribution values was utilized to evaluate the change in the standard thermodynamic quantities of enthalpy (ΔH°), entropy (ΔS°), and Gibbs free energy (ΔG°).

scholarly journals Parametric, equilibrium and kinetic studies on the removal of mercury using ion exchange resin

2017 ◽  
Vol 12 (2) ◽  
pp. 305-313 ◽  
Author(s):  
N. Rajamohan ◽  
M. Rajasimman
Keyword(s):  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Strong Acid ◽  
Ion Exchange Resin ◽  
Second Order ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Acid Cation ◽  
Pseudo Second Order ◽  
Langmuir Constants

This experimental research was an investigation into removal of mercury by using a strong acid cation resin, 001 × 7. Parametric experiments were conducted to determine the optimum pH, resin dosage, agitation speed and the effect of change in concentration in the range of 50–200 mg/L. High resin dosages favoured better removal efficiency but resulted in lower uptakes. Equilibrium experiments were performed and fitted to Langmuir and Freundlich isotherm models. Langmuir model suited well to this study confirming the homogeneity of the resin surface. The Langmuir constants were estimated as qmax = 110.619 mg/g and KL = 0.070 L/g at 308 K. Kinetic experiments were modeled using Pseudo second order model and higher values of R2 (>0.97) were obtained. The Pseudo second order kinetic constants, namely, equilibrium uptake (qe) and rate constant (k2), were evaluated as 59.17 mg/g and 40.2 × 10−4 g mg−1 min−1 at an initial mercury concentration of 100 mg/L and temperature of 308 K.

scholarly journals Banana Fibers as Sorbent for Removal of Acid Green Dye from Water

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Siti Kartina Abdul Karim ◽  
Soh Fong Lim ◽  
S. N. David Chua ◽  
Shanti Faridah Salleh ◽  
Puong Ling Law
Keyword(s):  
Freundlich Isotherm ◽  
Sorption Process ◽  
Agitation Speed ◽  
Second Order ◽  
Order Kinetic ◽  
Solution Ph ◽  
Banana Fiber ◽  
Banana Fibers ◽  
Pseudo Second Order ◽  
Banana Leaves

In this study, banana fibers extracted from banana leaves, stem, and stalk were used to remove acid green dye from aqueous solution. Three initial concentrations (750, 1000, and 1500 ppm) were chosen to determine the kinetic characteristics of the banana fiber sorbents at 25°C, agitation speed of 200 rpm, and total contact time of 3 hours. The pseudo-first-order, pseudo-second-order, and Dunwald-Wagner kinetic models were applied to the experimental kinetic data. For isotherm study, the batch experiments were performed at 25°C, initial pH 2, agitation speed of 200 rpm, and initial concentrations between 100 and 2000 ppm. The experimental data was fitted to the Langmuir, Freundlich, Dubinin-Radushkevich, and Temkin isotherms. The equilibrium was achieved in less than 90 minutes. The removal of the acid green dye was found to be following closely the pseudo-second-order kinetic model. For equilibrium study, the Freundlich isotherm was found to fit well with adsorption of acid green dye on the banana leaves, stem, and stalk sorbents. The calculated mean free energy of 4–11 J/mol indicated that the sorption process was mostly physical in nature. Experimental results also showed the adsorption performance is greatly affected by the initial solution pH.

scholarly journals Itaconic acid-modified layered double hydroxide as a ‎novel adsorbent for effective removal of Congo red from aqueous solutions

2021 ◽  
Author(s):  
Mohammad Dinari ◽  
Shirin Shabani
Keyword(s):  
Layered Double Hydroxide ◽  
Itaconic Acid ◽  
Congo Red ◽  
Aqueous Media ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Order Kinetic ◽  
Solution Ph ◽  
Pseudo Second Order ◽  
Double Hydroxide

Abstract Herein, we report the synthesis of Cu-Ca-Al/NO3-based layered double hydroxide through co-precipitation methodology. The prepared layered double hydroxide was then modified with itaconic acid. The physicochemical properties of the prepared materials were studied using Fourier transform-infrared spectroscopy, scanning electron microscopy, X-ray diffraction analysis, thermogravimetric analysis, and nitrogen adsorption/desorption technique. The prepared materials were then applied as novel adsorbents for the removal of Congo red as a model of an anionic dye from aqueous media. To reach maximum adsorption, the effect of parameters including sample solution pH, adsorbent amount, contact time, and initial concentration of Congo red on the adsorption process was investigated. Kinetic studies were also conducted to study the mechanism of adsorption. In this regard, the kinetic models of pseudo-first-order, pseudo-second-order, Elovich, and intra-particle diffusion were studied. The results showed that the adsorption of Congo red onto Cu-Ca-Al-LDH and LDH-ITA adsorbents followed the pseudo-second-order kinetic model. To evaluate the equilibrium adsorption data, different isotherms including Langmuir, Freundlich, and Dubinin-Radushkevich were also applied. The data revealed that the Freundlich isotherm provided the best fit with the equilibrium data of both adsorbents. Maximum adsorption capacities of 81 and 84 mg g− 1 were obtained using Cu-Ca-Al-LDH and LDH-ITA adsorbents, respectively.

scholarly journals Prediction of adsorption efficiency for the removal malachite green and acid blue 161 dyes by marble sludge dust using ANN

2014 ◽  
Vol 16 (4) ◽  
pp. 676-689 ◽  
Keyword(s):  
Experimental Data ◽  
Malachite Green ◽  
Second Order ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Ann Model ◽  
Marble Dust ◽  
Pseudo Second Order ◽  
Acid Blue

<div> <p>In the present study, batch adsorption studies were performed for the removal of malachite green and acid blue 161 dyes from aqueous solutions by varying parameters such as contact time, waste marble dust amount, initial dye concentration and temperature. The equilibrium adsorption data were analyzed by Langmuir, Freundlich and Temkin adsorption isotherm models. The Langmuir and Freundlich adsorption models agree well with experimental data. The pseudo-second order, intraparticle intraparticle diffusion and Elovich kinetic models were applied to the experimental data in order to describe the removal mechanism of dye ions by waste marble dust. The pseudo-second order kinetic was the best fit kinetic model for the experimental data. Thermodynamics parameters such as Δ<em>G</em>, Δ<em>H</em> and Δ<em>S </em>were also calculated for the adsorption processes. The experimental data were used to construct an artificial neural network (ANN) model to predict removal of malachite green and acid blue 161 dyes by waste marble dust. A three-layer ANN, an input layer with four neurons, a hidden layer with 12 neurons, and an output layer with one neuron is constructed. Different training algorithms were tested on the model to obtain the proper weights and bias values for ANN model. The results show that waste marble dust is an efficient sorbent for malachite green dye and ANN network, which is easy to implement and is able to model the batch experimental system.</p> </div> <p>&nbsp;</p>

scholarly journals Comparative Study between Zn and Cu Nano Ferrite in Removal of Heavy Metals and Microorganisms from Water

2021 ◽  
Vol 17 (4) ◽  
pp. 1-19
Author(s):  
Azhar Jabbar Bohan ◽  
Ghaed Khalef Salman ◽  
Ghaidaa Majeed Jaid
Keyword(s):  
Heavy Metals ◽  
Composite Materials ◽  
Freundlich Isotherm ◽  
Nano Particles ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Adsorption Method ◽  
Nano Composite ◽  
Removal Of Heavy Metals

The effect of Nano composite materials (CuFe2O4 and ZnFe2O4) was studied for removal of heavy metals (Cd (II) and Pb (II)) from wastewater by batch adsorption method and explain their effect on the antimicrobial effectiveness on gram positive and negative bacteria. Nano composite materials were characterized by XRD where the result indicates that the average crystallite sizes were around 36.19 nm for ZnFe2O4 and 12.22 nm for CuFe2O4.The effect of contact time, adsorbent dose, pH and type of adsorbents was used to find the optimum condition for removal of Cd(II) and Pb(II) ions .The equilibrium adsorption data was good fitted to the Langmuir and Freundlich isotherm models, and the pseudo first-order kinetic model showed the excellent fit in adsorption equilibrium capacity. The best pH used for removal was 7. The good removal reaches at the time 45 min for cadmium and need more time for lead. When increasing dosage of adsorbents, the removal efficiency increases. Freundlich and Langmuir isotherm gave the best fit experimental data. Also, antibacterial effects of this nano particles demonstrated the effect of CuFe2O4 NPs on bacteria more than used ZnFe2O4 NPs, and the percentage of bacterial death was increased according to increase the concentration of this materials.

scholarly journals Biosorption of cationic and anionic dyes using the biomass of Aspergillus parasiticus CBS 100926T

2021 ◽  
Author(s):  
Hadj Daoud Bouras ◽  
Ahmed RédaYeddou ◽  
Noureddine Bouras ◽  
Abdelmalek Chergui ◽  
Lidia Favier ◽  
...  
Keyword(s):  
Aspergillus Parasiticus ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Isotherm Models ◽  
Phenol Red ◽  
Order Kinetic ◽  
Acid Dyes ◽  
Anionic Dyes ◽  
Adsorption Processes ◽  
Pseudo Second Order

Aspergillus parasiticus (A. parasiticus) CBS 100926T was used as a biosorbent for the removal of Methylene Blue (MB), Congo Red (CR), Sudan Black (SB), Malachite Green Oxalate (MGO), Basic Fuchsin (BF) and Phenol Red (PR) from aqueous solutions. The batch biosorption studies were carried out as a function of dye concentration and contact time. The biosorption process followed the pseudo-first-order and the pseudo-second-order kinetic models and the Freundlich and Langmuir isotherm models. The resulting biosorbent was characterized by Scanning Electron Microscopy (SEM), X-Ray Diffractometer and Fourier Transformer Infrared Spectroscopy (FTIR) techniques. The results of the present investigation suggest that A. parasiticus can be used as an environmentally benign and low cost biomaterial for the removal of basic and acid dyes from aqueous solution. HIGHLIGHTS Micro-fungi Aspergillus parasiticus CBS100926T was employed as a new biosorbent for the biosorption of six dyes. The maximum dye capacity was found to be 131.58 mg/g. Adsorption processes can reach equilibrium within 120 min. Adsorption processes follow the pseudo-second-order rate equation. The results of equilibrium sorption were described through Freundlich isotherm.

Sign in / Sign up

Export Citation Format

Share Document