scholarly journals Adsorption of penicillin by decaffeinated tea waste

2015 ◽  
Vol 17 (3) ◽  
pp. 95-99 ◽  
Author(s):  
Parvin Gharbani ◽  
Ali Mehrizad ◽  
Ismail Jafarpour
Keyword(s):  
High Performance ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Solution Ph ◽  
First Order ◽  
Tea Waste ◽  
Main Factor

Abstract Removal of penicillin has been investigated using decaffeinated tea waste (DCTW). Decaffeination of tea waste was investigated using different methods. Results indicate that ozonation was the most effective process for removal of penicillin. Batch adsorption experiments were completed at various temperatures (20, 30, and 40°C), DCTW dosages (2, 4, 6, 8, and 10 g per 250 mL), penicillin concentrations (4, 10, and 14 mg/L), and pH (3, 7, and 10) conditions. Studies showed that adsorption reaches equilibrium within 40 min. The main factor affecting adsorption of penicillin was the solution pH, with maximum adsorption occurring at pH 3. Higher adsorbent dosages and lower penicillin concentrations also resulted in higher percentages of penicillin removal. Results show that data obeyed the pseudo-first-order kinetic and Freundlich isotherm models. This process proves that low-cost DCTW could be used as a high performance adsorbent for removing penicillin from aqueous solutions.

scholarly journals Kinetics and adsorption studies of lead (II) onto activated carbon using low cost adsorbents

2018 ◽  
Vol 20 (2) ◽  
pp. 381-388 ◽  
Keyword(s):  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Rate Limiting Step ◽  
Bambusa Vulgaris ◽  
Order Kinetic Model ◽  
Pseudo Second Order ◽  
Fagopyrum Esculentum Moench

The removal of Lead (II) from aqueous solutions using Fagopyrum esculentum Moench (Buckwheat) and Bambusa vulgaris (common bamboo) as adsorbents was investigated. The effects of various experimental parameters such as initial concentration, contact time and pH have been studied using batch adsorption technique. All the Adsorption isotherm models fitted well with the adsorption data. However, Freundlich isotherm displayed a better fitting model than the other two isotherm models due to high correlation coefficient (R2). This indicates the applicability of multilayer coverage of the Pb (II) on the surface of adsorbent. The adsorption kinetics was studied using four simplified models and it was found to follow the pseudo-second-order kinetic model which confirmed the applicability of the model. The adsorption mechanism was found to be chemisorption and the rate-limiting step was mainly surface adsorption.

scholarly journals Experimental study of the adsorption of Zn2 + ions on Natural Calcium Carbonate

2019 ◽  
Vol 9 (1) ◽  
pp. 78-84
Author(s):  
Karima Abellaoui ◽  
Hassan EL Kafssaoui ◽  
Hakima Nassali ◽  
Otheman Amrhar ◽  
Mohammed S. Elyoubi ◽  
...  
Keyword(s):  
Kinetic Equation ◽  
Calcium Carbonate ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Adsorption Kinetic ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Solution Ph ◽  
Order Kinetic Equation

In this study, Natural Calcium Carbonate (NCC) that was characterised by X-ray diffraction has been used as an adsorbent in the removal of Zn2+, from aqueous solution by a batch adsorption technique. The effects of various experimental parameters such as solution PH, initial concentration of solution, contact time, adsorbent masses and stirring speed were investigated. The results showed that basic PH and the average stirring speed were favourable for the adsorption of Zn2+, and the adequate equilibrium time for the adsorption of Zn2+ onto Natural Calcium Carbonate was 80min. The experimental data were analysed by the linear form of Langmuir, Freundlich. Isotherm models and showed a good fit with the Langmuir isotherm model. Adsorption kinetic was studied using pseudo first order kinetic equation, second order kinetic equation. The adsorption kinetic followed the pseudo second order equation. 

scholarly journals A novel biochar derived from cauliflower (Brassica oleracea L.) roots could remove norfloxacin and chlortetracycline efficiently

2017 ◽  
Vol 76 (12) ◽  
pp. 3307-3318 ◽  
Author(s):  
Tingting Qin ◽  
Zhaowei Wang ◽  
Xiaoyun Xie ◽  
Chaoran Xie ◽  
Junmin Zhu ◽  
...  
Keyword(s):  
High Efficiency ◽  
Raw Materials ◽  
Low Cost ◽  
Energy Dispersive Spectrometer ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Solution Ph ◽  
Initial Ph ◽  
Intra Particle Diffusion

Abstract The biochar was prepared by pyrolyzing the roots of cauliflowers, at a temperature of 500 °C under oxygen-limited conditions. The structure and characteristics of the biochar were examined using scanning electron microscopy, an energy dispersive spectrometer, a zeta potential analyzer, and Fourier transform infrared spectroscopy. The effects of the temperature, the initial pH, antibiotic concentration, and contact time on the adsorption of norfloxacin (NOR) and chlortetracycline (CTC) onto the biochar were investigated. The adsorption kinetics of NOR and CTC onto the biochar followed the pseudo-second-order kinetic and intra-particle diffusion models. The adsorption isotherm experimental data were well fitted to the Langmuir and Freundlich isotherm models. The maximum adsorption capacities of NOR and CTC were 31.15 and 81.30 mg/g, respectively. There was little difference between the effects of initial solution pH (4.0–10.0) on the adsorption of NOR or CTC onto the biochar because of the buffering effect. The biochar could remove NOR and CTC efficiently in aqueous solutions because of its large specific surface area, abundant surface functional groups, and particular porous structure. Therefore, it could be used as an excellent adsorbent material because of its low cost and high efficiency and the extensive availability of the raw materials.

Preparation of graphite by thermal annealing of polyacrylamide precursor for adsorption of Cs(I) and Co(II) ions from aqueous solutions

2012 ◽  
Vol 90 (10) ◽  
pp. 843-850 ◽  
Author(s):  
H.S. Hassan ◽  
Elsayed K. Elmaghraby
Keyword(s):  
Aqueous Solutions ◽  
Freundlich Isotherm ◽  
Effect Of Temperature ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Equilibration Time ◽  
Thermodynamic Quantities ◽  
Order Kinetic ◽  
Solution Ph ◽  
Radical Chain

In the present work, graphite nanostructures are prepared by thermolysis of a prepared polyacrylamide gel. The gel was prepared by radical chain polymerization and the synthesis of the nanostructures was done by step annealing at different temperatures. The structural of the prepared materials was studied by X-ray diffraction (XRD). The presence of carboxylic and phenolic functional groups on the graphite surface was confirmed by FT-IR analysis. Batch adsorption experiments were conducted to study the effect of equilibration time, initial metal cation concentration, and solution pH for the removal of Cs(I) and Co(II) from aqueous solutions. Kinetic data of Cs(I) adsorption was found to be well fitted with a pseudo-first-order kinetic model. The obtained isotherm data were correlated with the Langumir and Freundlich isotherm models. The effect of temperature on the equilibrium distribution values was utilized to evaluate the change in the standard thermodynamic quantities of enthalpy (ΔH°), entropy (ΔS°), and Gibbs free energy (ΔG°).

scholarly journals Equilibrium, Kinetics, and Thermodynamics of the Removal of Nickel(II) from Aqueous Solution Using Cow Hooves

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
I. Osasona ◽  
O. O. Ajayi ◽  
A. O. Adebayo
Keyword(s):  
Aqueous Solution ◽  
Contact Time ◽  
Room Temperature ◽  
Physical Adsorption ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Equilibrium Studies ◽  
Equilibrium Data

The feasibility of using powdered cow hooves (CH) for removing Ni2+ from aqueous solution was investigated through batch studies. The study was conducted to determine the effect of pH, adsorbent dosage, contact time, adsorbent particle size, and temperature on the adsorption capacity of CH. Equilibrium studies were conducted using initial concentration of Ni2+ ranging from 15 to 100 mgL−1 at 208, 308, and 318 K, respectively. The results of our investigation at room temperature indicated that maximum adsorption of Ni2+ occurred at pH 7 and contact time of 20 minutes. The thermodynamics of the adsorption of Ni2+ onto CH showed that the process was spontaneous and endothermic. Langmuir, Freundlich, and Dubinin-Radushkevich (D-R) isotherm models were used to quantitatively analysed the equilibrium data. The equilibrium data were best fitted by Freundlich isotherm model, while the adsorption kinetics was well described by pseudo-second-order kinetic equation. The mean adsorption energy obtained from the D-R isotherm revealed that the adsorption process was dominated by physical adsorption. Powdered cow hooves could be utilized as a low-cost adsorbent at room temperature under the conditions of pH 7 and a contact time of 20 minutes for the removal of Ni(II) from aqueous solution.

scholarly journals Kush - A Potential Biosorbent in the removal of Cd (II) and Zn (II) from aqueous solution

2012 ◽  
Vol 27 ◽  
pp. 107-114
Author(s):  
Jagjit Kour ◽  
P. L. Homagai ◽  
M. R. Pokherel ◽  
K. N. Ghimire
Keyword(s):  
Low Cost ◽  
Freundlich Isotherm ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Waste Streams ◽  
Adsorption Capacities ◽  
Optimum Ph ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order

The industrial discharge of heavy metals into waters' course is one of the major pollution problems affecting water quality. Therefore, they must be removed prior to their discharge into waste streams. An efficient and low-cost bioadsorbent has been investigated from Desmostachya bipinnata (Kush) by charring with concentrated sulphuric acid and functionalized with dimethylamine.It was characterised by SEM, FTIR and elemental analysis. The effect of pH, initial concentration and contact time of the metal solution was monitered by batch method. The maximum adsorption capacities were determined for Cd and Zn at their optimum pH 6. The equilibrium data were analysed using Langmuir and Freundlich isotherm models. Langmuir isotherm model fitted well and the rate of adsorption followed the pseudo second order kinetic equation.DOI: http://dx.doi.org/10.3126/jncs.v27i1.6669 J. Nepal Chem. Soc., Vol. 27, 2011 107-114  

scholarly journals Comparative Study between Zn and Cu Nano Ferrite in Removal of Heavy Metals and Microorganisms from Water

2021 ◽  
Vol 17 (4) ◽  
pp. 1-19
Author(s):  
Azhar Jabbar Bohan ◽  
Ghaed Khalef Salman ◽  
Ghaidaa Majeed Jaid
Keyword(s):  
Heavy Metals ◽  
Composite Materials ◽  
Freundlich Isotherm ◽  
Nano Particles ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Order Kinetic ◽  
Adsorption Method ◽  
Nano Composite ◽  
Removal Of Heavy Metals

The effect of Nano composite materials (CuFe2O4 and ZnFe2O4) was studied for removal of heavy metals (Cd (II) and Pb (II)) from wastewater by batch adsorption method and explain their effect on the antimicrobial effectiveness on gram positive and negative bacteria. Nano composite materials were characterized by XRD where the result indicates that the average crystallite sizes were around 36.19 nm for ZnFe2O4 and 12.22 nm for CuFe2O4.The effect of contact time, adsorbent dose, pH and type of adsorbents was used to find the optimum condition for removal of Cd(II) and Pb(II) ions .The equilibrium adsorption data was good fitted to the Langmuir and Freundlich isotherm models, and the pseudo first-order kinetic model showed the excellent fit in adsorption equilibrium capacity. The best pH used for removal was 7. The good removal reaches at the time 45 min for cadmium and need more time for lead. When increasing dosage of adsorbents, the removal efficiency increases. Freundlich and Langmuir isotherm gave the best fit experimental data. Also, antibacterial effects of this nano particles demonstrated the effect of CuFe2O4 NPs on bacteria more than used ZnFe2O4 NPs, and the percentage of bacterial death was increased according to increase the concentration of this materials.

From coordination polymer to carbon nanotube: Preparation, characterization and rapid adsorption capacity toward organic pollutants

2020 ◽  
Vol 44 (7-8) ◽  
pp. 487-493
Author(s):  
Hong-Yan Lin ◽  
Yi-Fei Wang ◽  
Yuan Tian ◽  
Guo-Cheng Liu ◽  
Jian Luan
Keyword(s):  
Carbon Nanotubes ◽  
Coordination Polymer ◽  
High Performance ◽  
Low Cost ◽  
Freundlich Isotherm ◽  
Catalyst Precursor ◽  
Order Kinetic ◽  
Order Kinetic Model ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes

A CuI coordination polymer based on the N,N’-bis(3-pyridinecarboxamide)-1,4-butane (3-dpyb) ligand, namely [Cu(3-dpyb)0.5Cl], is hydrothermally synthesized and structurally characterized, and is used as a catalyst precursor to synthesize multi-walled carbon nanotubes. Interestingly, the as-grown multi-walled carbon nanotubes exhibit high performance in removing dyes from solution and can serve as a low-cost and fast adsorbent. In addition, the adsorption behavior of this new adsorbent fits well with the Freundlich isotherm and the pseudo-second-order kinetic model.

Adsorption of Aqueous Using Granular Adsorbents from Accanthospermum hispendum DC

2021 ◽  
Vol 13 (1) ◽  
Author(s):  
Sunusi A. Zubair ◽  
◽  
Umar Ibrahim Gaya ◽  
Keyword(s):  
Activated Carbons ◽  
Low Cost ◽  
Kinetic Scheme ◽  
Freundlich Isotherm ◽  
Sub Saharan Africa ◽  
Isotherm Models ◽  
Order Kinetic ◽  
Lead Uptake ◽  
Effects Of Ph ◽  
Sub Saharan

Granular activated carbons have been important adsorbents for the decontamination of aqueous environmental contaminants. Acanthospermum hispidum weed represents a ready available source of low-cost adsorbents in sub-Saharan Africa that has barely been paid attention. The effects of pH, contact time, concentration, adsorbent dosage, particle size and temperature on the adsorptive removal of Pb (II) from aqueous solutions over activated carbon granules from the thorns of Accanthospermum hispindum (AC-T) were for the first time investigated and compared with those of the leaves (L), the sodium hydroxide modified thorns (NaOH-T) and regular thorns (T) of this plant. These adsorbents were characterised by the surface charge analysis, scanning electron microscopy (SEM) and the Attenuated Total Reflectance Fourier Transform infrared (ATR FTIR) spectroscopy. The SEM revealed a wafer-like appearance for the AC-T with a large distribution of open pores. The adsorption data of lead uptake onto the adsorbents were examined using two pseudo-order kinetic schemes and three isotherm models. To fully understand the adsorption capacities of the adsorbents, batch desorption recoveries were studied. The FTIR depicted the various functionalities responsible for the adsorption. Adsorption over AC-T was found to agree with pseudo second-order kinetic scheme, the Langmuir and Freundlich isotherm. This material exhibited the highest adsorption capacity. The order of reusability of the adsorbents is T < AC-T < NaOH-T.

Parametric and adsorption kinetic studies of methylene blue removal from simulated textile water using durian (Durio zibethinus murray) skin

2015 ◽  
Vol 72 (6) ◽  
pp. 896-907 ◽  
Author(s):  
S. M. Anisuzzaman ◽  
Collin G. Joseph ◽  
D. Krishnaiah ◽  
A. Bono ◽  
L. C. Ooi
Keyword(s):  
Methylene Blue ◽  
Adsorption Capacity ◽  
Dye Adsorption ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Isotherm Models ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Durio Zibethinus

In this study, durian (Durio zibethinus Murray) skin was examined for its ability to remove methylene blue (MB) dye from simulated textile wastewater. Adsorption equilibrium and kinetics of MB removal from aqueous solutions at different parametric conditions such as different initial concentrations (2–10 mg/L), biosorbent dosages (0.3–0.7 g) and pH solution (4–9) onto durian skin were studied using batch adsorption. The amount of MB adsorbed increased from 3.45 to 17.31 mg/g with the increase in initial concentration of MB dye; whereas biosorbent dosage increased from 1.08 to 2.47 mg/g. Maximum dye adsorption capacity of the durian skin was found to increase from 3.78 to 6.40 mg/g, with increasing solution pH. Equilibrium isotherm data were analyzed according to Langmuir and Freundlich isotherm models. The sorption equilibrium was best described by the Freundlich isotherm model with maximum adsorption capacity of 7.23 mg/g and this was due to the heterogeneous nature of the durian skin surface. Kinetic studies indicated that the sorption of MB dye tended to follow the pseudo second-order kinetic model with promising correlation of 0.9836 &lt; R2 &lt; 0.9918.

Sign in / Sign up

Export Citation Format

Share Document