Influence of Friction Stir Welding Parameters on Tensile Strength of Semi-solid Cast 2024 Aluminum Alloy Butt Joints

2020 ◽  
Vol 31 (2) ◽  
Author(s):  
Angkarn Kamruan ◽  
Somsak Siwadamrongpong ◽  
Ukrit Thanasubtawee ◽  
Prapas Muangjunburee
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Welding Parameters ◽  
Butt Joints ◽  
2024 Aluminum Alloy ◽  
Friction Stir ◽  
Semi Solid

scholarly journals Innovate Method for Friction Stir Welding of Al-Mg-Si Alloy Thin Plate

2019 ◽  
Vol 269 ◽  
pp. 02006
Author(s):  
Li Fu ◽  
Fenjun Liu
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Base Metal ◽  
High Speed ◽  
Thick Plate ◽  
Welding Parameters ◽  
Butt Joints ◽  
Friction Stir ◽  
High Rotation Speed ◽  
Precipitated Phases

Al-Mg-Si (6061-T6) alloy with 0.8 mm thick plate was welded successfully by use of high speed friction stir welding (FSW) technology. The microstructural characteristics and mechanical property of the butt joints prepared by high speed FSW were analyzed in detail, the influence of welding parameters, fixture condition and after welding heat treatment were also explored. The results shown that sound surface topography and defect-free bonding interface were observed in the nugget zone (NZ). The microhardness of the as-welded joint was lower than that of the base metal because of the welding heat effect. Compared with the conventional speed FSW, the number of β-Mg2Si, Al2CuMg and Al8Fe2Si precipitated phases existed in the high speed FSWed NZ increased, which made the microhardness in the NZ improved significantly. The rod-shaped precipitates (Mg2Si) have the greatest influence on the microhardness distributions. The maximum tensile strength of 301.8 MPa, which was 85.8% of the base metal, was obtained at high rotation speed of 8000 rpm and fast welding speed of 1500 mm/min. The tensile strength of the ultra-high speed FSWed butt joints were improved significantly by post-weld artificial aging, with a maximum joint efficiency of 90.4%.

Heat Transfer Simulations and Analysis of Joint Cross-Sectional Microstructure on Friction Stir Welding between Steel and Aluminium

2020 ◽  
Vol 863 ◽  
pp. 85-95
Author(s):  
Truong Minh Nhat ◽  
Truong Quoc Thanh ◽  
Tu Vinh Thong ◽  
Tran Trong Quyet ◽  
Luu Phuong Minh
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Thermal Contact ◽  
Welding Process ◽  
Welding Parameters ◽  
Thermal Imager ◽  
Sem Images ◽  
Cross Sectional ◽  
Friction Stir

This study presents conducted heat simulations and experimental jointing flat-plate of aluminum alloy 6061 and SUS 304. Temperature is simulated by the COMSOL software in three states: (1) Preheat the Friction Stir Welding (FSW) by TIG welding, (2) Thermal contact resistance between Aluminium and steel, and (3) The welding process using stiring friction is simulated. The simulations intended to predicting the temperature which is used for preheat and welding process to ensuring the required solid-state welding. The temperature is also determined and checked by a thermal imager comparing with simulation results. Besides, the results of tensile strength is carried out. The Box - Behnken method is used to identify the relationship between the welding parameters (rotation, speed and offset), temperature and tensile strength. The maximum tensile strength is 77% compared to the strength of aluminum alloy. The optimal set of parameters for the process is n = 676 rpm, v = 46 mm / min and x = 0.6 mm. The optimizing welding parameters to achieving good quality of welding process are described. SEM images to determine some properties of welding materials. This is also the basis for initial research to identify some defects in welding of two different materials (IMC thickness and interconnected pores) and the cause of these defects.

Optimizing friction stir welding parameters to maximize tensile strength of AA2219 aluminum alloy joints

2009 ◽  
Vol 15 (2) ◽  
pp. 321-330 ◽  
Author(s):  
S. Babu ◽  
K. Elangovan ◽  
V. Balasubramanian ◽  
M. Balasubramanian
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Welding Parameters ◽  
Friction Stir ◽  
Aa2219 Aluminum Alloy

Researching on hybrid friction stir welding between two differential materials as steel and aluminium

2020 ◽  
Vol 3 (SI1) ◽  
pp. First
Author(s):  
Truong Minh Nhat ◽  
Truong Quoc Thanh ◽  
Tran Trong Quyet ◽  
Luu Phuong Minh
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Solid State ◽  
Welding Process ◽  
Welding Parameters ◽  
Thermal Imager ◽  
Friction Stir ◽  
Hybrid Techniques ◽  
State Process

Friction stir welding exploits its solid-state process behavior to join aluminum to steel, which differs in thermal and mechanical properties, and where a combination of these metallic alloys by fusion welding prompts a deleterious reaction as a result of the melting and resolidification phases. Recently, hybrid techniques have been employed in FSW for several materials and alloys, particularly for steel–steel joining. These methods are generally aimed to pre-heat the steel plate materials. This study presents conducted heat simulations and experimental jointing flat-plate of aluminum alloy 6061 and SUS 304. Temperature is simulated by the COMSOL software in three states: (1) Preheat the Friction Stir Welding (FSW) by TIG welding, (2) Thermal contact resistance between aluminum and steel, and (3) The welding process using stirring friction is simulated. The simulations intended to predict the temperature, which is used for the preheating and welding process to ensuring the required solid-state welding. The temperature is also determined and checked by a thermal imager comparing with simulation results. Besides, the results of tensile strength are carried out. The Box - Behnken method is used to identify the relationship between the welding parameters (rotation, speed, and offset), temperature, and tensile strength. The maximum tensile strength is 77% compared to the strength of the aluminum alloy. The optimal set of parameters for the process is n = 676 rpm, v = 46 mm / min and x = 0.6 mm. The optimizing welding parameters to achieving a good quality of the welding process are described. SEM images to determine some properties of welding materials. This is also the basis for initial research to identify some defects in the welding of two different materials (IMC thickness and interconnected pores) and the cause of these defects.

scholarly journals Evaluation of Optimization Parameters of Semi-Solid Metal 6063 Aluminum Alloy from Friction Stir Welding Process Using Factorial Design Analysis

2020 ◽  
Vol 4 (4) ◽  
pp. 123
Author(s):  
Chaiyoot Meengam ◽  
Kittima Sillapasa
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Rotation Speed ◽  
Welding Process ◽  
Solid Metal ◽  
Stir Zone ◽  
Friction Stir ◽  
6063 Aluminum Alloy ◽  
Semi Solid

The semi-solid-metal 6063 aluminum alloy was developed for the automotive industry. The objective of this research was to optimize parameters in friction stir welding process that can provide the highest tensile strength. The ANOVA factorial design was used to analyze rotation speed, welding speed, and tool geometry at different factor levels of experimentation. The results showed that the optimized tensile strength was 120.7 MPa from the cylindrical tool, rotation speed was from 1300 to 2100 rpm, and welding speed less than 75 mm/min in the coefficient of determination R2 was 95.09%, as can be considered from the regression equation. The examination of the stir-zone and thermal mechanical affected zone using SEM and EDX showed that the new recrystallization of the microstructure causes fine grain in the stir-zone, coarse grain in advancing-side thermal mechanical affected zone, and equiaxed grain in the retracting-side thermal-mechanical affect zone. The intermetallic compounds of β-Al5FeSi phase transformation phase were formed to three types, i.e., β″-Al5Fe, Mg2Si, and Al8Fe2Si phase were observed. Moreover, in the stir-zone and thermal-mechanical-affected zone, defects were found such as flash defects, void or cavity defects, crack defects, lack of penetration defects, tunnel defects, kissing bond defects, and dendrite formation defects affecting weldability.

A Study on Grain Size, Mechanical Properties and First Mode of Metal Transfer in Underwater Friction Stir Welded AA5052-O

2018 ◽  
Vol 775 ◽  
pp. 466-472 ◽  
Author(s):  
K. Tejonadha Babu ◽  
S. Muthukumaran ◽  
C. Bharat Kumar
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Metal Transfer ◽  
Welding Parameters ◽  
Friction Stir ◽  
Second Mode ◽  
Underwater Friction Stir Welding

Friction stir welding (FSW), a new joining process is finding extensive use in the welding of aluminum alloy sheets. The metal transfer modes in the FSW cause the quality of the weld and its properties. The first mode of metal transfer is accomplished by the tool and shoulder, while the second mode occurs around the pin. In the present study, two different welding conditions, which were friction stir welding in the air (CFSW) and underwater friction stir welding (UWFSW) carried out at various welding parameters to weld the AA5052-O aluminum alloy sheets and determine the consequence of the first mode on the tensile strength of welded joints. Considerable grain refinement and enhanced mechanical properties were obtained in UWFSW joints. It Is observed that the first mode affect the tensile strength of the joint, also found that a linear correlation between the first mode and the tensile strength.

scholarly journals Optimized Parameter for Butt Joint in Friction Stir Welding of Semi-Solid Aluminum Alloy 5083 Using Taguchi Technique

2021 ◽  
Vol 5 (3) ◽  
pp. 88
Author(s):  
Konkrai Nakowong ◽  
Kittima Sillapasa
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Butt Joint ◽  
Grain Structure ◽  
Shipbuilding Industry ◽  
Friction Stir ◽  
Semi Solid ◽  
5083 Aluminum Alloy

The semi-solid metal (SSM) 5083 aluminum alloy was developed for part manufacturing in the marine shipbuilding industry. This study aimed to optimize the parameters for the friction stir welding process of SSM 5083 aluminum alloy using the Taguchi and analysis of variance (ANOVA) techniques. Our analyses included tensile strength, hardness value, and the microstructure. The results revealed that the optimal parameters obtained for the tensile strength and hardness value in the stir zone (SZ) were A1B1C2 (1000 rpm, 10 mm/min, with a threaded cylindrical tool) with a tensile strength of 235.22 MPa and A2B1C2 (1200 rpm, 10 mm/min, with a threaded cylindrical tool) with a hardness value of 80.64 HV. According to the results obtained by ANOVA, it was found that the welding speed was the most significant process parameter in terms of influencing the tensile strength. Contrarily, no parameter influenced the hardness at a 95% confidence level. The examination using scanning electron microscopy (SEM) and an energy dispersive X-ray spectroscope (EDS) revealed an elongated grain structure and a void defect at the pin tip on the advancing side (AS) in the SZ. The particle distribution was uniform with Al2O3 and small porous SiO2 phases. Moreover, the quantities of C, O, Al, F, and Mg decreased.

scholarly journals Identifying Combination of Friction Stir Welding Parameters to Maximize Strength of Lap Joints of AA2014-T6 Aluminum Alloy

2017 ◽  
Vol 37 (1) ◽  
pp. 6-21 ◽  
Author(s):  
C. Rajendrana ◽  
K. Srinivasan ◽  
V. Balasubramanian ◽  
H. Balaji ◽  
P. Selvaraj
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Weight Ratio ◽  
Welding Process ◽  
Lap Joints ◽  
Fusion Welding ◽  
Welding Parameters ◽  
Friction Stir

AbstractAA2014 aluminum alloy (Al-Cu alloy) has been widely utilized in fabrication of lightweight structures like aircraft structures, demanding high strength to weight ratio and good corrosion resistance. The fusion welding of these alloys will lead to solidification problems such as hot cracking. Friction stir welding is a new solid state welding process, in which the material being welded does not melt and recast. Lot of research works have been carried out by many researchers to optimize process parameters and establish empirical relationships to predict tensile strength of friction stir welded butt joints of aluminum alloys. However, very few investigations have been carried out on friction stir welded lap joints of aluminum alloys. Hence, in this investigation, an attempt has been made to optimize friction stir lap welding (FSLW) parameters to attain maximum tensile strength using statistical tools such as design of experiment (DoE), analysis of variance (ANOVA), response graph and contour plots. By this method, it is found that maximum tensile shear fracture load of 12.76 kN can be achieved if a joint is made using tool rotational speed of 900 rpm, welding speed of 110 mm/min, tool shoulder diameter of 12 mm and tool tilt angle of 1.5°.

scholarly journals Tensile Strength, Micro-hardness and Microstructure of Friction-Stir-Welding AA6061-T4 Joints

2018 ◽  
Vol 25 (4) ◽  
pp. 50-55
Author(s):  
Najeeb S. Abtan ◽  
Ataalah Hussain Jassim ◽  
Mustafa S. M. Al-Janabi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Base Metal ◽  
High Hardness ◽  
Welding Parameters ◽  
Micro Hardness ◽  
Friction Stir ◽  
Wide Range

Welding of aluminum alloys by traditional welding methods creates some defects such as hot cracks, porosity, and void that led to decreasing of mechanical properties. Friction Stir Welding (FSW) gives good mechanical properties of aluminum alloy welds. In this paper, FSW worked in 4 mm thick plate of 6061-T4 aluminum alloy, with two welding parameters are used (tool rotational speed and feed rate) was investigated, were analyzed the microstructure and mechanical properties by carried out microstructural, micro-hardness, and tensile strength tests. From results are found defect-free of welds at a wide range of parameters. Stir zone shows a fine-equiaxed grain and high hardness, not significantly change between heat affected zone and base metal in size grain. Tensile strength of welds was lower than base metal and fracture location was occurred at a low hardness region for the welds.

Optimization of friction stir welding parameters of dissimilar aluminium alloys 6061 and 5083 by using response surface methodology

2021 ◽  
pp. 095440622110058
Author(s):  
Sanjeev Verma ◽  
Vinod Kumar
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Tilt Angle ◽  
Feed Rate ◽  
Aluminium Alloys ◽  
Welded Joint ◽  
Welding Parameters ◽  
Friction Stir ◽  
Industrial Sectors ◽  
Tool Pin

Aluminium and its alloys are lightweight, corrosion-resistant, affordable and high-strength material and find wide applications in shipbuilding, automotive, constructions, aerospace and other industrial sectors. In applications like aerospace, marine and automotive industries, there is a need to join components made of different aluminium alloys, viz. AA6061 and AA5083. In this study friction stir welding (FSW) is used to join dissimilar plates made of AA6061-T6 and AA5083-O. The effect of varying tool pin profile, tool rotation speed, tool feed rate and tilt angle of the tool has been investigated on the tensile strength and percentage elongation of the welded joints. Box-Behkan design, with four input parameters and three levels of each parameter has been employed to decide the set of experimental runs. The regression models have been developed to investigate the influence of welding variables on the tensile strength and elongation of the welded joint. It is revealed that with the increase in welding parameters like tool rpm, tool feed rate and tilt angle of the tool, both the mechanical properties increase, reach a maximum level, followed by a decrease with further increase in the value of parameters. Amongst different types of tool pin profiles used, the FSW tool having straight cylindrical (SC) pin profile is found to yield the maximum strength and elongation of the welded joint for different combinations of welding parameters. Multiple response optimization indicates that the maximum UTS (135.83 MPa) and TE (4.35%) are obtained for the welded joint fabricated using FSW tool having SC pin profile, tilted at 1.11° and operating at tool speed and feed rate of 1568 rpm and 39.53 mm/min., respectively.

Sign in / Sign up

Export Citation Format

Share Document