scholarly journals Innovate Method for Friction Stir Welding of Al-Mg-Si Alloy Thin Plate

2019 ◽  
Vol 269 ◽  
pp. 02006
Author(s):  
Li Fu ◽  
Fenjun Liu
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Base Metal ◽  
High Speed ◽  
Thick Plate ◽  
Welding Parameters ◽  
Butt Joints ◽  
Friction Stir ◽  
High Rotation Speed ◽  
Precipitated Phases

Al-Mg-Si (6061-T6) alloy with 0.8 mm thick plate was welded successfully by use of high speed friction stir welding (FSW) technology. The microstructural characteristics and mechanical property of the butt joints prepared by high speed FSW were analyzed in detail, the influence of welding parameters, fixture condition and after welding heat treatment were also explored. The results shown that sound surface topography and defect-free bonding interface were observed in the nugget zone (NZ). The microhardness of the as-welded joint was lower than that of the base metal because of the welding heat effect. Compared with the conventional speed FSW, the number of β-Mg2Si, Al2CuMg and Al8Fe2Si precipitated phases existed in the high speed FSWed NZ increased, which made the microhardness in the NZ improved significantly. The rod-shaped precipitates (Mg2Si) have the greatest influence on the microhardness distributions. The maximum tensile strength of 301.8 MPa, which was 85.8% of the base metal, was obtained at high rotation speed of 8000 rpm and fast welding speed of 1500 mm/min. The tensile strength of the ultra-high speed FSWed butt joints were improved significantly by post-weld artificial aging, with a maximum joint efficiency of 90.4%.

scholarly journals Tensile Strength, Micro-hardness and Microstructure of Friction-Stir-Welding AA6061-T4 Joints

2018 ◽  
Vol 25 (4) ◽  
pp. 50-55
Author(s):  
Najeeb S. Abtan ◽  
Ataalah Hussain Jassim ◽  
Mustafa S. M. Al-Janabi
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Base Metal ◽  
High Hardness ◽  
Welding Parameters ◽  
Micro Hardness ◽  
Friction Stir ◽  
Wide Range

Welding of aluminum alloys by traditional welding methods creates some defects such as hot cracks, porosity, and void that led to decreasing of mechanical properties. Friction Stir Welding (FSW) gives good mechanical properties of aluminum alloy welds. In this paper, FSW worked in 4 mm thick plate of 6061-T4 aluminum alloy, with two welding parameters are used (tool rotational speed and feed rate) was investigated, were analyzed the microstructure and mechanical properties by carried out microstructural, micro-hardness, and tensile strength tests. From results are found defect-free of welds at a wide range of parameters. Stir zone shows a fine-equiaxed grain and high hardness, not significantly change between heat affected zone and base metal in size grain. Tensile strength of welds was lower than base metal and fracture location was occurred at a low hardness region for the welds.

Optimization of friction stir welding parameters of dissimilar aluminium alloys 6061 and 5083 by using response surface methodology

2021 ◽  
pp. 095440622110058
Author(s):  
Sanjeev Verma ◽  
Vinod Kumar
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Tilt Angle ◽  
Feed Rate ◽  
Aluminium Alloys ◽  
Welded Joint ◽  
Welding Parameters ◽  
Friction Stir ◽  
Industrial Sectors ◽  
Tool Pin

Aluminium and its alloys are lightweight, corrosion-resistant, affordable and high-strength material and find wide applications in shipbuilding, automotive, constructions, aerospace and other industrial sectors. In applications like aerospace, marine and automotive industries, there is a need to join components made of different aluminium alloys, viz. AA6061 and AA5083. In this study friction stir welding (FSW) is used to join dissimilar plates made of AA6061-T6 and AA5083-O. The effect of varying tool pin profile, tool rotation speed, tool feed rate and tilt angle of the tool has been investigated on the tensile strength and percentage elongation of the welded joints. Box-Behkan design, with four input parameters and three levels of each parameter has been employed to decide the set of experimental runs. The regression models have been developed to investigate the influence of welding variables on the tensile strength and elongation of the welded joint. It is revealed that with the increase in welding parameters like tool rpm, tool feed rate and tilt angle of the tool, both the mechanical properties increase, reach a maximum level, followed by a decrease with further increase in the value of parameters. Amongst different types of tool pin profiles used, the FSW tool having straight cylindrical (SC) pin profile is found to yield the maximum strength and elongation of the welded joint for different combinations of welding parameters. Multiple response optimization indicates that the maximum UTS (135.83 MPa) and TE (4.35%) are obtained for the welded joint fabricated using FSW tool having SC pin profile, tilted at 1.11° and operating at tool speed and feed rate of 1568 rpm and 39.53 mm/min., respectively.

Effect of Friction Stir Welding Parameters on Thermal and Tensile Behavior of Aluminum Weldments Using Double Shoulder Tools

2012 ◽  
Vol 622-623 ◽  
pp. 323-329
Author(s):  
Ebtisam F. Abdel-Gwad ◽  
A. Shahenda ◽  
S. Soher
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Welding Process ◽  
Tensile Behavior ◽  
Frictional Heat ◽  
Welding Parameters ◽  
Friction Stir ◽  
Aluminum Base ◽  
Tool Pin ◽  
Strength And Ductility

Friction stir welding (FSW) process is a solid state welding process in which the material being welded does not melt or recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters and tool pin profile play major roles in deciding the weld quality. In this investigation, an attempt has been made to understand effects of process parameters include rotation speeds, welding speeds, and pin diameters on al.uminum weldment using double shoulder tools. Thermal and tensile behavior responses were examined. In this direction temperatures distribution across the friction stir aluminum weldment were measured, besides tensile strength and ductility were recorded and evaluated compared with both single shoulder and aluminum base metal.

Features for friction stir welding of butt joints of casting VAL8 alloy with wrought 1565chN2 and AMg6M alloys

2021 ◽  
pp. 441-449
Author(s):  
V.A. Berezina ◽  
V.V. Ovchinnikov ◽  
E.V. Luk'yanenko
Keyword(s):  
Grain Size ◽  
Tensile Strength ◽  
Friction Stir Welding ◽  
Chemical Composition ◽  
Arc Welding ◽  
Butt Joints ◽  
Friction Stir ◽  
Discrete Nature ◽  
Casting Aluminum ◽  
Tool Rotation

The results of technological features for friction stir welding of butt joints of sheet blanks with thickness of 3 mm made of casting aluminum V AL8 alloy with wrought magnalium group 1565chN2 and AMg6M alloys are presented. It is established that the time resistance of the joints depends on the location of the welded alloys relative to the direction of tool rotation during friction stir welding. The ultimate strength of welded joints of VAL8 alloy with 1565chN2 and AMg6 alloys in automatic argon-arc welding is 0.82...0.84 of the ultimate tensile strength of VAL8 alloy. The grain size in the stir zone practically does not depend on the initial grain size in the alloys to be joined. The destruction of the joints made of VAL8 + 1565chH2 alloys under cyclic loading has multi-focal character and is initiated from irregularities on the surface of the weld. The discrete nature of the change in the chemical composition of the weld metal along the axis of the weld is revealed. The weld is formed by alternating strips of connected alloys with width of 30...90 microns.

Heat Transfer Simulations and Analysis of Joint Cross-Sectional Microstructure on Friction Stir Welding between Steel and Aluminium

2020 ◽  
Vol 863 ◽  
pp. 85-95
Author(s):  
Truong Minh Nhat ◽  
Truong Quoc Thanh ◽  
Tu Vinh Thong ◽  
Tran Trong Quyet ◽  
Luu Phuong Minh
Keyword(s):  
Tensile Strength ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Thermal Contact ◽  
Welding Process ◽  
Welding Parameters ◽  
Thermal Imager ◽  
Sem Images ◽  
Cross Sectional ◽  
Friction Stir

This study presents conducted heat simulations and experimental jointing flat-plate of aluminum alloy 6061 and SUS 304. Temperature is simulated by the COMSOL software in three states: (1) Preheat the Friction Stir Welding (FSW) by TIG welding, (2) Thermal contact resistance between Aluminium and steel, and (3) The welding process using stiring friction is simulated. The simulations intended to predicting the temperature which is used for preheat and welding process to ensuring the required solid-state welding. The temperature is also determined and checked by a thermal imager comparing with simulation results. Besides, the results of tensile strength is carried out. The Box - Behnken method is used to identify the relationship between the welding parameters (rotation, speed and offset), temperature and tensile strength. The maximum tensile strength is 77% compared to the strength of aluminum alloy. The optimal set of parameters for the process is n = 676 rpm, v = 46 mm / min and x = 0.6 mm. The optimizing welding parameters to achieving good quality of welding process are described. SEM images to determine some properties of welding materials. This is also the basis for initial research to identify some defects in welding of two different materials (IMC thickness and interconnected pores) and the cause of these defects.

scholarly journals Improvement on Mechanical Properties of Submerged Friction Stir Joining of Dissimilar Tailor Welded Aluminum Blanks

2021 ◽  
Vol 2021 ◽  
pp. 1-6
Author(s):  
R. Suryanarayanan ◽  
V. G. Sridhar ◽  
L. Natrayan ◽  
S. Kaliappan ◽  
Anjibabu Merneedi ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Friction Stir Welding ◽  
Mechanical Performance ◽  
Weld Zone ◽  
Tensile Tests ◽  
Welding Parameters ◽  
Negative Effects ◽  
Friction Stir ◽  
Tailor Welded Blanks ◽  
Secondary Precipitates

Friction stir welding is a solid-state welding method that produces joints with superior mechanical and metallurgical properties. However, the negative effects of the thermal cycle during welding dent the mechanical performance of the weld joint. Hence, in this research study, the joining of aluminum tailor welded blanks by friction stir welding is carried out in underwater conditions by varying the welding parameters. The tensile tests revealed that the underwater welded samples showed better results when compared to the air welded samples. Maximum tensile strength of 229.83 MPa was obtained at 1000 rpm, 36 mm/min. The improved tensile strength of the underwater welded samples was credited to the suppression of the precipitation of the secondary precipitates due to the cooling action provided by the water. The lowest hardness of 72 HV was obtained at the edge of the stir zone which indicated the weakest region in the weld zone.

Sign in / Sign up

Export Citation Format

Share Document