scholarly journals Utilizing Recycled Concrete and Stone Aggregate as Replace-ment for Natural and Crushed Virgin Aggregate

2018 ◽  
Vol 7 (4.37) ◽  
pp. 90
Author(s):  
Zaid Al-Azzawi ◽  
. .
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Recycled Concrete ◽  
Modulus Of Rupture ◽  
Concrete Aggregate ◽  
Strength Increase ◽  
Lower Grade ◽  
Replacement Ratio ◽  
Alternative Choice

The mechanical properties of recycled concrete aggregate form Al-Anbar province in Iraq is presented in this paper. Recycled concrete and stone aggregates were utilized as replacements for both natural and crushed virgin aggregate. Four series of tests were conducted to study various replacement ratios (0.25, 0.50, 0.75 and 1.0) effect on compressive strength, splitting tensile strength and modulus of rupture. Density of concrete in addition to its water absorption were also investigated. Results of this work show that replacing natural and crushed virgin aggregate with waste concrete aggregate extracted from left-over concrete cubes and concrete barriers did not affect its mechanical properties significantly. In fact, in this study the general trend is that the compressive strength increases with increasing the replacement ratio from 0.0 to 1.0. However, the tensile strength showed different behaviour as there was a limit for the strength increase with replacement ratio where beyond it the strength started decreasing again. This limit varied between 0.50 and 0.75 depending on the type of aggregate used and the type of the test. The age of test did not affect the behaviour of the trialled mixes significantly. In addition to that, recycled stone aggregate proved to be an alternative choice only for lower grade concrete because it reduced both compressive and tensile strength in comparison to the reference mix. 

Experimental Study on Strength of Recycled Concrete

2013 ◽  
Vol 357-360 ◽  
pp. 1282-1285
Author(s):  
Hai Yong Cai ◽  
Li Bin Fu ◽  
Ling Bo Dang
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Great Influence ◽  
Recycled Concrete ◽  
Replacement Ratio ◽  
Cement Ratio ◽  
Water Cement Ratio ◽  
Concrete Mechanical Properties

Influence of replacement ratio and water-cement ratio on the recycled concrete mechanical properties were analyzed by testing the compressive strength and tensile strength of the recycled concrete. Results show that the mechanical properties of recycled concrete, compared with common concrete, can meet the requirements of the project. Water-cement ratio has great influence on compressive strength and tensile strength, replacement ratio has obvious influence on compressive strength but little on tensile.

scholarly journals Roller Compacted Concrete with Recycled Concrete Aggregate for Paving Bases

2020 ◽  
Vol 12 (8) ◽  
pp. 3154 ◽  
Author(s):  
Hedelvan Emerson Fardin ◽  
Adriana Goulart dos Santos
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Modulus Of Elasticity ◽  
Splitting Tensile Strength ◽  
Recycled Concrete ◽  
Concrete Aggregate ◽  
Recycled Concrete Aggregate ◽  
Roller Compacted Concrete ◽  
Flexural Tensile Strength ◽  
Mechanical And Physical Properties

This research aimed to investigate the mechanical and physical properties of Roller Compacted Concrete (RCC) used with Recycled Concrete Aggregate (RCA) as a replacement for natural coarse aggregate. The maximum dry density method was adopted to prepare RCC mixtures with 200 kg/m³ of cement content and coarse natural aggregates in the concrete mixture. Four RCC mixtures were produced from different RCA incorporation ratios (0%, 5%, 15%, and 30%). The compaction test, compressive strength, splitting tensile strength, flexural tensile strength, and modulus of elasticity, porosity, density, and water absorption tests were performed to analyze the mechanical and physical properties of the mixtures. One-way Analysis of Variance (ANOVA) was used to identify the influences of RCA on RCC’s mechanical properties. As RCA increased in mixtures, some mechanical properties were observed to decrease, such as modulus of elasticity, but the same was not observed in the splitting tensile strength. All RCCs displayed compressive strength greater than 15.0 MPa at 28 days, splitting tensile strength above 1.9 MPa, flexural tensile strength above 2.9 MPa, and modulus of elasticity above 19.0 GPa. According to Brazilian standards, the RCA added to RCC could be used for base layers.

scholarly journals Effect of the Alkalized Rice Straw Content on Strength Properties and Microstructure of Cemented Tailings Backfill

2021 ◽  
Vol 8 ◽  
Author(s):  
Shi Wang ◽  
Xuepeng Song ◽  
Meiliang Wei ◽  
Wu Liu ◽  
Xiaojun Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Rice Straw ◽  
Low Cost ◽  
Strength Properties ◽  
Hydration Reaction ◽  
Strength Increase ◽  
Improvement Effect ◽  
Naoh Solution

The tailings and rice straw are waste by-products, and the storage of tailings on the ground and the burning of rice straws will seriously damage the ecological environment. In this study, the effect of different contents of alkalized rice straw (ARS; rice straw was alkalized with 4% NaOH solution) on the mechanical properties and microstructure of cemented tailings backfill (CTB; ARSCTB) was studied through uniaxial compressive strength (UCS), scanning electron microscopy (SEM), and X-ray diffraction (XRD) tests. The results indicated that 1) the UCS of ARSCTB could be improved by ARS. However, with the increase in the ARS content from 0.1 to 0.4 wt%, the UCS showed a monotonous decreasing trend. The UCS improvement effect was best when the ARS content was 0.1 wt%, and at 7, 14, and 28 days curing ages, the UCS increased rate was 6.0, 8.3, 14.7% respectively. 2) The tensile strength of ARSCTB was generally higher than that of CTB and positively correlated with the ARS content. The tensile strength increase rate was 24.1–34.2% at 28 days curing age. 3) The SEM test indicated that the ARS was wrapped by cement hydration products, which improves its connection with the ARSCTB matrix. ARS performed a bridging role, inhibited cracks propagation, and provided drag or pulling force for the block that is about to fall off. Therefore, the mechanical properties of ARSCTB were enhanced. However, under high ARS content, the inhibition of ARS on hydration reaction and the overlap between ARS were not conducive to the improvement of the UCS of ARSCTB. 4) The post-peak residual strength and integrity effect of ARSCTB were greater. It is recommended to add 0.1–0.2 wt% ARS to the backfill with high compressive strength requirements such as the empty field subsequent filling mining method and the artificial pillar. 0.3–0.4 wt% ARS is incorporated into backfill with high tensile strength requirements such as high-stage filling with lateral exposure and artificial roof. This study further makes up for the blank of the application of plant fiber in the field of mine filling and helps to improve the mechanical properties of backfill through low-cost materials.

scholarly journals Effect of Steel Fibers on Heat of Hydration and Mechanical Properties of Concrete Containing Fly Ash

2019 ◽  
Vol 38 (1) ◽  
pp. 83-94 ◽  
Author(s):  
Sajid Mehmood ◽  
Faheem Butt
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Construction Projects ◽  
Heat Of Hydration ◽  
Steel Fibers ◽  
Modulus Of Rupture ◽  
Consistent Increase ◽  
Lower Heat

This study investigated the effects of steel fibers on the fresh and hardened properties, and heat of hydration of concrete containing FA (Fly Ash). A total of 192 samples were cast comprising cubes, cylinders, and prisms, for six concrete mixes with varying contents of steel fibers by volume and a fixed content of FA i.e. 15% by weight of cement. The semi adiabatic setup was used to monitor temperature rise due to the heat of hydration in the concrete mixes for fourteen days. The use of FA increased workability, and decreased early compressive strength, tensile strength and heat of hydration of concrete. However, an increase in the compressive strength of FA concrete was observed by the addition of steel fibers up to 0.9% whereas a consistent increase in the splitting tensile strength and modulus of rupture was observed with the addition of the steel fibers from 0.4-1.8%. Further the test results showed that increasing steel fibers content decrease the evolution of heat due to hydration. It was concluded that the FA concrete with steel fibers can be used in precast industry and mass construction projects due to the improved mechanical properties and lower heat of hydration.

scholarly journals Mechanical Properties of Macro Polypropylene Fibre-Reinforced Concrete

Polymers ◽  
2021 ◽  
Vol 13 (23) ◽  
pp. 4112
Author(s):  
Rajab Abousnina ◽  
Sachindra Premasiri ◽  
Vilive Anise ◽  
Weena Lokuge ◽  
Vanissorn Vimonsatit ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Reinforced Concrete ◽  
Plain Concrete ◽  
Modulus Of Rupture ◽  
Fibre Reinforced Concrete ◽  
Empirical Formulas ◽  
Pull Out ◽  
Mechanical And Microstructural Properties

Adding fibers to concrete helps enhance its tensile strength and ductility. Synthetic fibres are preferable to steel ones which suffer from corrosion that reduces their functionality with time. More consideration is given to synthetic fibres as they can be sourced from waste plastics and their incorporation in concrete is considered a new recycling pathway. Thus, this work investigates the potential engineering benefits of a pioneering application using extruded macro polyfibres in concrete. Two different fiber dosages, 4 kg/m3 and 6 kg/m3, were used to investigate their influence based on several physical, mechanical and microstructural tests, including workability, compressive strength, modulus of elasticity, splitting-tensile strength, flexural test, CMOD, pull-out test and porosity. The test results revealed a slight decrease in the workability of the fibre-reinforced concrete, while all the mechanical and microstructural properties were enhanced significantly. It was observed that the compressive, splitting tensile and bonding strength of the concrete with 6 kg/m3 fibre dosage increased by 19.4%, 41.9% and 17.8% compared to the plain concrete specimens, respectively. Although there was no impact of the fibres on the modulus of rupture, they significantly increased the toughness, resulting in a progressive type of failure instead of the sudden and brittle type. Moreover, the macroporosity was reduced by the fibre addition, thus increasing the concrete compressive strength. Finally, simplified empirical formulas were developed to predict the mechanical properties of the concrete with fibre addition. The outcome of this study will help to increase the implementation of the recycled plastic waste in concrete mix design and promote a circular economy in the waste industry.

scholarly journals Mechanical and Structural Properties of a Lightweight Concrete with Different Types of Recycling Coarse Aggregate

2019 ◽  
Vol 26 (1) ◽  
pp. 33-40
Author(s):  
Muyasser M. Jomaa’h ◽  
Baraa Thaer Kamil ◽  
Omer S. Baghabra
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
High Efficiency ◽  
Coarse Aggregate ◽  
Splitting Tensile Strength ◽  
Modulus Of Rupture ◽  
Unit Weight ◽  
Dry Density ◽  
Total Density

The light of the world’s technological development in the construction field and the continuous need to apply of a high-efficiency building materials because old methods is no longer is used after the advent of the solutions that characterized by fast applications and maximum protection in addition to reducing costs and increase the sustainability of the establishment and its design age. The lightweights of various installations are an urgent need to decrease the dead loads. Therefore, this study is specie locally focus on replacing the normal coarse aggregate with lightweight coarse aggregate (claystone (bonza), rubber, thermostone and polystyrene) in various volumetric ratios of (25, 50 and 75) % in addition to a preparation reference mix. For the purpose identifying and studying the important specifications the new concrete which contributes to the self-load reduction of the concrete by reducing the total density of the mixture, were prepared models of cylinders and standard prisms, to evaluate the compressive strength and the splitting tensile strength respectively, Also the modulus of rupture and the unit weight, where carried out. The results tests indicated that a drop in the mechanical properties of the concrete with increasing the lightweight coarse aggregate , mechanical properties values : compressive strength , rupture modulus, splitting tensile strength and flexural strength were between (10.66-28.99) MPa (1.122-3.372) MPa, (3.606-6.83) MPa and (20.101-25.874)MPa compared with a reference mixes (38.44MPa), (3.969MPa), (10.476MPa) and (26.940)MPa respectively for mixes of (25, 50 and75)% with different light coarse aggregate , also the values of an oven dry density were between (1665.5-2287.58)kg/m3 compared with reference mixes (2426.41kg/m³). The best concrete mix was (M7, M10) of low density (1598.4 kg/m3) and (1580.4) kg /m3 and the compression strength within the permissible limits (15.47) MPa.

scholarly journals The influence of recycled concrete aggregate on the properties of concrete

2018 ◽  
Vol 162 ◽  
pp. 02020 ◽  
Author(s):  
Nisreen Mohammed ◽  
Kaiss Sarsam ◽  
Mazin Hussien
Keyword(s):  
Compressive Strength ◽  
Coarse Aggregate ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Modulus Of Rupture ◽  
Concrete Aggregate ◽  
Hardened Concrete ◽  
Recycled Coarse Aggregate ◽  
Natural Aggregates

Use of Recycled Coarse Aggregate (RCA) in concrete can be described in terms of environmental protection and economy. This paper deals with the mechanical properties of concrete compressive strength, splitting tensile strength, modulus of elasticity, and modulus of rupture. Three kinds of concrete mixtures were tested, concrete made with Natural Coarse Aggregate (NCA) as a control concrete and two types of concrete made with recycled coarse aggregate (50% and 100% replacement level of coarse recycled aggregate). These kinds of concrete were made with different targets of compressive strength of concrete f ’c (35MPa) and (70 MPa). Fifty specimens were tested of the fresh and hardened properties of concrete. The waste concrete from laboratory test cubes was crushed to produce the Recycled Coarse Aggregate used in recycled concrete. A comparative between the experimental results of the properties for fresh and hardened concrete is presented in the paper. Recycled aggregate concrete (RCA) had a satisfactory performance despite the replacement ratios. It was found using the size of Recycled Coarse Aggregate (RCA) of (5-14) mm has quite similar in performance with the same size of Natural Coarse Aggregate (NCA), it is necessary to use high quality of recycled concrete (with low levels of impurities). Recycled aggregate as an alternative to natural aggregates -seems quite successful.

scholarly journals Concrete Properties using Treated Recycled EPS

2021 ◽  
Vol 877 (1) ◽  
pp. 012028
Author(s):  
Hasan Jasim Mohammed ◽  
Yasir Gaib Hussein
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Silica Fume ◽  
Coarse Aggregate ◽  
Splitting Tensile Strength ◽  
The Other ◽  
Modulus Of Rupture ◽  
Normal Concrete ◽  
Concrete Properties

Abstract The study explores the mechanical properties of treated recycled extended polystyrene (TEPS) concrete, treated by two methods, one by heating, and the other by immersed recycled EPS in cement neat. By substituting 0 %, 15 %, 25 %, and 35 % of the coarse aggregate volume with treated recycled EPS, (for both method). Treated recycled TEPS concrete ratios are experimentally prepared, while the cement is substituted thru 10 % silica fume (SF). Tests were carried out, like compressive strength, splitting tensile strength, modulus of rupture, and density. The outcomes display the decreasing of the compressive strength, tensile strength and modulus of rupture of TEPS concretes with rise TEPS percentage around 26 %, 17 % and 32 %, respectively (35% TEPS) related to standard concrete. They also show that TEPS concrete density decrease about 30 % of normal concrete. The TEPS is suitable in concrete and meets provisions.

scholarly journals Mechanical Performance of Recycled Aggregate Concrete Containing Lathe Waste Steel Fibre

2021 ◽  
Vol 17 (4) ◽  
pp. 306-311
Author(s):  
S.A. Alabi ◽  
C. Arum
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Building Materials ◽  
Steel Fibre ◽  
Mechanical Performance ◽  
Recycled Concrete ◽  
Recycled Aggregate Concrete ◽  
Recycled Aggregate ◽  
Concrete Aggregate ◽  
Aggregate Concrete

The increasing demand, diminishing supplies, and growing pressure on natural resources have necessitated recycling and reusing waste. Several kinds of research have been done on the reuse and recycling of debris from building projects. Thus, with a view to the reuse of waste materials, the elimination of environmental contamination, the reduction of overhead costs of concrete, and the extension of the service life of concrete structures, this research aimed to study the feasibility of utilizing recycled concrete aggregate (RCA) with constant inclusion of waste steel fibre (LWSF) in concrete by evaluating its workability, compressive and splitting tensile strengths. A concrete mix ratio of 1:2:4 by weight of cement, sand, and granite was adopted with a water-cement ratio of 0.45. Five different concrete mixes were prepared in this study; one normal aggregate concrete (NAC) and four (4) other mixes with 25%, 50%, 75%, and 100% recycled aggregate content with a constant 1.5% addition of LWSF. The result of workability shows a reduction with an increase in the percentage replacement level. The recycled aggregate concrete (RAC) was characterized by lower compressive strength as compared with the NAC. When the replacement ratio increased from 25% to 50%, a significant reduction of about 14% and 30% were observed in the compressive strength at 7-days, but at 28-days slight increase in the compressive strength was observed. Also, a decrease in splitting tensile strength as the percentage replacement of crushed granite (CG) with RCA is increased was observed. Overall, the findings showed that the RAC-containing LWSF is environmentally sustainable and would significantly reduce the global greenhouse impact and building materials' overall quality. Keywords: Recycled concrete, lathe waste, steel fibre, compressive strength, tensile strength

EFFECT OF RECYCLED CONCRETE AGGREGATE QUALITY ON PROPERTIES OF CONCRETE

2020 ◽  
Vol 15 (2) ◽  
pp. 57-69
Author(s):  
Daniel Hatungimana ◽  
Şemsi Yazıcı ◽  
Ali Mardani-Aghabaglou
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Recycled Concrete ◽  
Recycled Aggregates ◽  
Concrete Aggregate ◽  
Hardened Concrete ◽  
Recycled Concrete Aggregate ◽  
Waste Concrete ◽  
Concrete Production

ABSTRACT The possibility of the use of recycled aggregates from the construction industry in green concrete production is of increasing importance to reduce the negative environmental impact associated with construction and demolition wastes. The objective of this study is to investigate the effect of recycled concrete aggregate (RCA) quality on the properties of hardened concrete properties such as compressive strength, splitting tensile strength, density, water absorption capacity and porosity accessible to water. The RCA used in this study was obtained from the crushing of waste concrete with two different compressive strengths (LRCA obtained from the crushing of waste concrete having compressive strengths below 30 MPa and HRCA obtained from the crushing of waste concrete having compressive strengths above 30 MPa). The natural coarse limestone aggregate was 100% replaced with coarse LRCA and HRCA. As a result of the study, the use of 100% HRCA and %100 LRCA instead of limestone coarse aggregate in the concrete adversely affected its mechanical and physical properties. In addition, HRCA showed better performance in terms of compressive strength, tensile strength, water absorption and porosity compared to the use of LRCA. Furthermore, the percentage of adhered mortar on the surface of LRCA and HRCA was analyzed using a computerized micro tomography device, and it was found that the percentages of attached mortar and aggregates are 61% and 35.5% for LRCA, whilst the attached mortar and aggregate contents for HRCA are 45.9% and 53.7%, respectively.

Sign in / Sign up

Export Citation Format

Share Document