scholarly journals Mechanical behaviour of acetylated rubber wood subjected to artificial weathering

Holzforschung ◽  
2019 ◽  
Vol 73 (11) ◽  
pp. 1005-1016 ◽  
Author(s):  
Samuel Oluyinka Olaniran ◽  
Cabane Etienne ◽  
Tobias Keplinger ◽  
Babatola Olufemi ◽  
Markus Rüggeberg
Keyword(s):  
Mechanical Properties ◽  
Reaction Times ◽  
Colour Change ◽  
Middle Lamella ◽  
Weight Percent ◽  
Mechanical Tests ◽  
Native Form ◽  
Rubber Wood ◽  
Strain Pattern ◽  
Over Exploitation

Abstract Rubber wood utilization in Nigeria has become a viable alternative because of over-exploitation of more durable species. The use of rubber wood in its native form has some disadvantages including dimensional instability, low durability and susceptibility to weathering in outdoor uses. However, it may be improved through chemical modification such as acetylation. In this study, we revealed the effectiveness of acetylation on the protection of rubber wood against weathering in terms of weight loss (WL), colour change, lignin degradation, and mechanical properties. Acetylation was carried out using two different reaction times to achieve weight percent gains (WPG) of around 7% and 10%. Understanding of the effect of acetylation and subsequent weathering on mechanical properties was enabled by analysing wood chemistry with Fourier transform infrared (FTIR) analysis and Raman spectroscopy. The mechanical tests of weathered unmodified and acetylated rubber wood revealed a decrease of tensile stiffness of the unmodified samples as a function of weathering time, while stiffness was retained for the acetylated samples. Weathered unmodified samples showed a bi-phasic stress-strain pattern with a high strain at breakage indicating a slippage of fibres under stress due to degradation of the middle lamella. This was hardly visible for acetylated samples. Thus, acetylation was shown to be effective for protecting rubber wood used in outdoor conditions.

Mechanical Properties of Glass–Fiber Polyester Reinforced Composites Filled with Nanometer Al2O3 Particles

2012 ◽  
Vol 586 ◽  
pp. 199-205
Author(s):  
Fatemeh Alavi ◽  
Ali Ashrafi
Keyword(s):  
Mechanical Properties ◽  
Glass Fiber ◽  
Fracture Behavior ◽  
Failure Modes ◽  
Glass Fibers ◽  
Weight Percent ◽  
Mechanical Tests ◽  
Nano Particles ◽  
Nano Particle ◽  
Particle Addition

In this research the effects of the nano-particle additions and two different fabric architectures of knitted E-glass fibers on the mechanical properties of polyester fiberglass composites were investigated. The particles selected was 50 nanometer in size Al2O3 particles. E-glass fibers were knitted using two different molds by two different arrangements. Specimens were machined and mechanical tests were conducted as per the accepted test standard. Tension, impact and fracture properties were measured and their associated failure modes were compared with each other. Fracture behavior of specimens with and without nano-particle addition in unidirectional tensile test was studied using Scanning Electron Microscopy (SEM). Results obtained showed that tensile strength of the composite is significantly dependent on nano-particle addition and E-glass fiber architecture. Addition of 0.2 weight percent nano-particles enhances the tensile properties of polyester fiberglass composites. It was found that fracture behavior of composite depends strongly on nano-particle addition.

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Effect of silver nitrate on some mechanical properties of heat polymerizing acrylic resins

2019 ◽  
Vol 14 (1) ◽  
pp. 110
Author(s):  
Assiss. Prof. Dr. Sabiha Mahdi Mahdi ◽  
Dr. Firas Abd K. Abd K.
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Silver Nitrate ◽  
Surface Hardness ◽  
Mechanical Tests ◽  
Hardness Tester ◽  
Acrylic Resins ◽  
The Difference

Aim: The aimed study was to evaluate the influence of silver nitrate on surfacehardness and tensile strength of acrylic resins.Materials and methods: A total of 60 specimens were made from heat polymerizingresins. Two mechanical tests were utilized (surface hardness and tensile strength)and 4 experimental groups according to the concentration of silver nitrate used.The specimens without the use of silver nitrate were considered as control. Fortensile strength, all specimens were subjected to force till fracture. For surfacehardness, the specimens were tested via a durometer hardness tester. Allspecimens data were analyzed via ANOVA and Tukey tests.Results: The addition of silver nitrate to acrylic resins reduced significantly thetensile strength. Statistically, highly significant differences were found among allgroups (P≤0.001). Also, the difference between control and experimental groupswas highly significant (P≤0.001). For surface hardness, the silver nitrate improvedthe surface hardness of acrylics. Highly significant differences were statisticallyobserved between control and 900 ppm group (P≤0.001); and among all groups(P≤0.001)with exception that no significant differences between control and150ppm; and between 150ppm and 900ppm groups(P>0.05).Conclusion: The addition of silver nitrate to acrylics reduced significantly the tensilestrength and improved slightly the surface hardness.

The Mechanical Properties of Organic Modified Epoxy Resin

2020 ◽  
Vol 43 (3) ◽  
pp. 10-14
Author(s):  
Georgel MIHU ◽  
Claudia Veronica UNGUREANU ◽  
Vasile BRIA ◽  
Marina BUNEA ◽  
Rodica CHIHAI PEȚU ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Epoxy Resin ◽  
Epoxy Matrix ◽  
Epoxy Resins ◽  
Mechanical Tests ◽  
Organic Modification ◽  
Three Point Bending ◽  
Modified Epoxy

Epoxy resins have been presenting a lot of scientific and technical interests and organic modified epoxy resins have recently receiving a great deal of attention. For obtaining the composite materials with good mechanical proprieties, a large variety of organic modification agents were used. For this study gluten and gelatin had been used as modifying agents thinking that their dispersion inside the polymer could increase the polymer biocompatibility. Equal amounts of the proteins were milled together and the obtained compound was used to form 1 to 5% weight ratios organic agents modified epoxy materials. To highlight the effect of these proteins in epoxy matrix mechanical tests as three-point bending and compression were performed.

scholarly journals Generation of Photopolymerized Microparticles Based on PEGDA Using Microfluidic Devices. Part 1. Initial Gelation Time and Mechanical Properties of the Material

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 293
Author(s):  
José M. Acosta-Cuevas ◽  
José González-García ◽  
Mario García-Ramírez ◽  
Víctor H. Pérez-Luna ◽  
Erick Omar Cisneros-López ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Gelation Time ◽  
Mesh Size ◽  
Microfluidic Devices ◽  
Future Generation ◽  
Mechanical Tests ◽  
Continuous Systems ◽  
Polyethylene Glycol Diacrylate ◽  
Glycol Diacrylate ◽  
Close Relationship

Photopolymerized microparticles are made of biocompatible hydrogels like Polyethylene Glycol Diacrylate (PEGDA) by using microfluidic devices are a good option for encapsulation, transport and retention of biological or toxic agents. Due to the different applications of these microparticles, it is important to investigate the formulation and the mechanical properties of the material of which they are made of. Therefore, in the present study, mechanical tests were carried out to determine the swelling, drying, soluble fraction, compression, cross-linking density (Mc) and mesh size (ξ) properties of different hydrogel formulations. Tests provided sufficient data to select the best formulation for the future generation of microparticles using microfluidic devices. The initial gelation times of the hydrogels formulations were estimated for their use in the photopolymerization process inside a microfluidic device. Obtained results showed a close relationship between the amount of PEGDA used in the hydrogel and its mechanical properties as well as its initial gelation time. Consequently, it is of considerable importance to know the mechanical properties of the hydrogels made in this research for their proper manipulation and application. On the other hand, the initial gelation time is crucial in photopolymerizable hydrogels and their use in continuous systems such as microfluidic devices.

scholarly journals Thermal, Physical and Mechanical Properties of Poly(Butylene Succinate)/Kenaf Core Fibers Composites Reinforced with Esterified Lignin

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2359
Author(s):  
Harmaen Ahmad Saffian ◽  
Masayuki Yamaguchi ◽  
Hidayah Ariffin ◽  
Khalina Abdan ◽  
Nur Kartinee Kassim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Loss Modulus ◽  
Physical And Mechanical Properties ◽  
Weight Percent Gain ◽  
Weight Percent ◽  
Esterification Reaction ◽  
Butylene Succinate ◽  
Kenaf Core ◽  
Modified Lignin

In this study, Kraft lignin was esterified with phthalic anhydride and was served as reinforcing filler for poly(butylene succinate) (PBS). Composites with different ratios of PBS, lignin (L), modified lignin (ML) and kenaf core fibers (KCF) were fabricated using a compounding method. The fabricated PBS composites and its counterparts were tested for thermal, physical and mechanical properties. Weight percent gain of 4.5% after lignin modification and the FTIR spectra has confirmed the occurrence of an esterification reaction. Better thermo-mechanical properties were observed in the PBS composites reinforced with modified lignin and KCF, as higher storage modulus and loss modulus were recorded using dynamic mechanical analysis. The density of the composites fabricated ranged from 1.26 to 1.43 g/cm3. Water absorption of the composites with the addition of modified lignin is higher than that of composites with unmodified lignin. Pure PBS exhibited the highest tensile strength of 18.62 MPa. Incorporation of lignin and KCF into PBS resulted in different extents of reduction in tensile strength (15.78 to 18.60 MPa). However, PBS composite reinforced with modified lignin exhibited better tensile and flexural strength compared to its unmodified lignin counterpart. PBS composite reinforced with 30 wt% ML and 20 wt% KCF had the highest Izod impact, as fibers could diverge the cracking propagation of the matrix. The thermal conductivity value of the composites ranged from 0.0903 to 0.0983 W/mK, showing great potential as a heat insulator.

scholarly journals Influence of a Natural Plant Antioxidant on the Ageing Process of Ethylene-norbornene Copolymer (Topas)

2021 ◽  
Vol 22 (8) ◽  
pp. 4018
Author(s):  
Anna Masek ◽  
Angelika Plota
Keyword(s):  
Mechanical Properties ◽  
Food Packaging ◽  
Colour Change ◽  
Good Alternative ◽  
Plant Origin ◽  
Aging Behavior ◽  
Current State ◽  
Ft Ir ◽  
Potential Use

In the field of polymer technology, a variety of mainly synthetic additives are used to stabilize the materials during processing. However, natural compounds of plant origin can be a green alternative to chemicals such as synthetic polyphenols. An analysis of the effect of hesperidin on the aging behavior of ethylene-norbornene copolymer was performed. The evaluation of changes in the tested samples was possible by applying the following tests: determination of the surface energy and OIT values, mechanical properties analysis, colour change measurements, FT-IR and TGA analyses. The obtained results proved that hesperidin can be effectively used as natural stabilizer for polymers. Furthermore, as a result of this compound addition to Topas-silica composites, their surface and physico-mechanical properties have been improved and the resistance to aging significantly increased. Additionally, hesperidin can act as a dye or colour indicator and only few scientific reports describe a possibility of using flavonoids to detect changes in products during their service life, e.g., in food packaging. In the available literature, there is no information about the potential use of hesperidin as a stabilizer for cycloolefin copolymers. Therefore, this approach may contribute not only to the current state of knowledge, but also presents an eco-friendly solution that can be a good alternative to synthetic stabilizers.

Mechanical Properties of Secondary Wall and Compound Corner Middle Lamella near the Phenol-Formaldehyde (PF) Adhesive Bond Line Measured by Nanoindentation

2011 ◽  
Vol 236-238 ◽  
pp. 1746-1751 ◽  
Author(s):  
Kun Liang ◽  
Guan Ben Du ◽  
Omid Hosseinaei ◽  
Si Qun Wang ◽  
Hui Wang
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Secondary Wall ◽  
Phenol Formaldehyde ◽  
Middle Lamella ◽  
Adhesive Bond ◽  
Cellular Level ◽  
Bond Line ◽  
Line Region ◽  
Penetration Behavior

To find out the penetration of PF into the wood cell wall and its effects onthe mechanical properties in the cellular level, the elastic modulus and hardness of secondary wall (S2layer) and compound corner middle lamella (CCML) near PF bond line region were determined by nanoindentation. Compare to the reference cell walls (unaffected by PF), PF penetration into the wood tissues showed improved elastic modulus and hardness. And the mechanical properties decreased slowly with the increasing the distance from the bond line, which are attributed to the effects of PF penetration into S2layer and CCML. The reduced elastic modulus variations were from18.8 to 14.4 GPa for S2layer, and from10.1 to 7.65 GPa for CCML. The hardness was from 0.67 to 0.52 GPa for S2layer, and from 0.65 to 0.52 GPa for CCML. In each test viewpoint place, the average hardness of CCML was almost as high as that of S2layer, but the reduced elastic modulus was about 50% less than that of S2layer. But the increase ratio of mechanical properties was close. All the results showed PF penetrates into the CCML. The penetration behavior and penetration depth from bond line were similar in both S2layer and CCML.

scholarly journals Fast Preparation of High-Performance Wood Materials Assisted by Ultrasonic and Vacuum Impregnation

Forests ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 567
Author(s):  
Hong Yang ◽  
Mingyu Gao ◽  
Jinxin Wang ◽  
Hongbo Mu ◽  
Dawei Qi
Keyword(s):  
Mechanical Properties ◽  
High Performance ◽  
Mechanical Tests ◽  
Vacuum Impregnation ◽  
Natural Forests ◽  
Ultrasonic Pretreatment ◽  
Fast Growing ◽  
Before And After ◽  
New Material ◽  
Ft Ir

In the absence of high-quality hardwood timber resources, we have gradually turned our attention from natural forests to planted fast-growing forests. However, fast-growing tree timber in general has defects such as low wood density, loose texture, and poor mechanical properties. Therefore, improving the performance of wood through efficient and rapid technological processes and increasing the utilization of inferior wood is a good way to extend the use of wood. Densification of wood increases the strength of low-density wood and extends the range of applications for wood and wood-derived products. In this paper, the effects of ultrasonic and vacuum pretreatment on the properties of high-performance wood were explored by combining sonication, vacuum impregnation, chemical softening, and thermomechanical treatments to densify the wood; then, the changes in the chemical composition, microstructure, and mechanical properties of poplar wood before and after treatment were analyzed comparatively by FT-IR, XRD, SEM, and mechanical tests. The results showed that with ultrasonic pretreatment and vacuum impregnation, the compression ratio of high-performance wood reached its highest level and the MOR and MOE reached their maximums. With the help of this method, fast-growing softwoods can be easily prepared into dense wood materials, and it is hoped that this new material can be applied in the fields of construction, aviation, and automobile manufacturing.

Sign in / Sign up

Export Citation Format

Share Document