Investigation of experimental study of end milling of CFRP composite

2015 ◽  
Vol 22 (1) ◽  
pp. 89-95 ◽  
Author(s):  
Erol Kiliçkap ◽  
Ahmet Yardimeden ◽  
Yahya Hışman Çelik
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Forces ◽  
End Milling ◽  
Cutting Speed ◽  
Machining Process ◽  
Cnc Milling ◽  
End Mill ◽  
Cfrp Composite

AbstractCarbon fiber-reinforced plastic (CFRP) composites are materials that are difficult to machine due to the anisotropic and heterogeneous properties of the material and poor surface quality, which can be seen during the machining process. The machining of these materials causes delamination and surface roughness owing to excessive cutting forces. This causes the material not to be used. The reduction of damage and surface roughness is an important aspect for product quality. Therefore, the experimental study carried out on milling of CFRP composite material is of great importance. End milling tests were performed at CNC milling vertical machining center. In the experiments, parameters considered for the end milling of CFRP were cutting speed, feed rate, and flute number of end mill. The results showed that damage, surface roughness, and cutting forces were affected by cutting parameters and flute number of end mill. The best machining conditions were achieved at low feed rate and four-flute end mill.

Machining Apprenticeship Based on Experimental Training Practice

2011 ◽  
Vol 692 ◽  
pp. 83-92
Author(s):  
Pedro Jose Arrazola ◽  
A. Villar ◽  
R. Fernández ◽  
J. Aperribay
Keyword(s):  
Surface Roughness ◽  
Power Consumption ◽  
Feed Rate ◽  
Cutting Forces ◽  
Theoretical Calculations ◽  
Cutting Speed ◽  
Machining Process ◽  
Depth Of Cut ◽  
Practical Training ◽  
Input Parameters

This article describes a practical machining training aiming that the students acquire the theoretical-practical knowledge of chip formation process. The training takes place after theoretical lessons of machining processes. Thus, this practice allows strengthening the knowledge gained during the lessons. The practical training lasts for five hours, and the student assisted by the teacher analyses the influence of some machining entry parameters (cutting speed, feed rate...) on exit parameters like: (I) cutting forces and power consumption, (II) surface roughness, and (III) chip typology. The practical session is carried out on an experimental set-up (Lathe CNC Danobar 65) equipped with sensors and devices to measure forces (sensor Kistler 9121) and power consumption. In addition, a portable rugosimeter (Hommelwerke) is employed to perform surface roughness measurements. No especial devices are needed for the chip typology analysis. In the case of cutting forces and power consumption, the following input parameters influences are analysed: feed rate, depth of cut and cutting speed. In the case of surface roughness analysis, the following input parameters influences are analysed: feed rate and nose radius of the cutting insert. Finally, regarding chip typology feed rate and depth of cut are examined. The experimental results are compared with model predictions (theoretical calculations) for the three issues studied. The students have to compare both results: theoretical an empirical and they need to explain the reasons when discrepancies appear. Results obtained during the last years demonstrate the student acquires better knowledge of the machining process, and at the same time realises of the process complexity.

Experimental Study of Cutting Forces in Micro End-Milling

2012 ◽  
Vol 500 ◽  
pp. 357-362 ◽  
Author(s):  
Xiu Bing Jing ◽  
Huai Zhong Li ◽  
Jun Wang ◽  
Jong Leng Liow
Keyword(s):  
Experimental Study ◽  
Feed Rate ◽  
Cutting Forces ◽  
End Milling ◽  
Cutting Speed ◽  
Micro Milling ◽  
Planning And Control ◽  
Micro End Milling ◽  
And Control ◽  
Cutting Speeds

Micro-end-milling is an efficient and economical manufacturing operation that is capable of accurately producing high aspect ratio features and parts. It is important to study the cutting forces in micro-milling for the planning and control of the process. This paper presents an experimental study of the cutting forces in micro-end-milling of a 6160 aluminum alloy. The measured cutting forces are presented and discussed for different cutting conditions, such as various feeds per tooth, cutter diameters, and cutting speeds. It is found that the peak cutting forces increase with increasing cutting speed and feed rate. The effects of tool runout on the cutting forces were also analyzed based on the experimental results, from which the influences of feed rate and cutting speed are found to be obvious.

Surface Roughness Model when Machining Aluminum Nitride Ceramic with Two Flute Square End Micro Grain Solid Carbide End Mill

2013 ◽  
Vol 747 ◽  
pp. 282-286 ◽  
Author(s):  
Moola Mohan Reddy ◽  
Alexander Gorin ◽  
K.A. Abou-El-Hossein ◽  
D. Sujan
Keyword(s):  
Surface Roughness ◽  
Aluminum Nitride ◽  
Feed Rate ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
End Mill ◽  
Roughness Model ◽  
Solid Carbide

This research presents the performance of Aluminum Nitride ceramic in end milling using two flute square end micro grain solid carbide end mill under dry cutting. Surface finish is one of the important requirements in the machining process. This paper describes mathematically the effect of cutting parameters on surface roughness in end milling process. The quadratic model for the surface roughness has been developed in terms of cutting speed, feed rate, and axial depth of cut using the response surface methodology (RSM). Design of experiments approach was employed in developing the surface roughness model in relation to cutting parameters. The predicted results are in good agreement with the experimental results within the specified range of cutting conditions. Experimental results showed surface roughness increases with increase in the cutting speed, feed rate, and the axial depth of cut.

scholarly journals Influence of Chatter of VMC Arising During End Milling Operation and Cutting Conditions on Quality of Machined Surface

1970 ◽  
Vol 2 (1) ◽  
Author(s):  
A.K.M.N. Amin, M.A. Rizal, and M. Razman
Keyword(s):  
Surface Roughness ◽  
Metal Cutting ◽  
Metal Removal ◽  
End Milling ◽  
Cutting Speed ◽  
Cutting Conditions ◽  
End Mill ◽  
Machined Surface ◽  
Operating Cycle ◽  
Wide Range

Machine tool chatter is a dynamic instability of the cutting process. Chatter results in poor part surface finish, damaged cutting tool, and an irritating and unacceptable noise. Exten¬sive research has been undertaken to study the mechanisms of chatter formation. Efforts have been also made to prevent the occurrence of chatter vibration. Even though some progress have been made, fundamental studies on the mechanics of metal cutting are necessary to achieve chatter free operation of CNC machine tools to maintain their smooth operating cycle. The same is also true for Vertical Machining Centres (VMC), which operate at high cutting speeds and are capable of offering high metal removal rates. The present work deals with the effect of work materials, cutting conditions and diameter of end mill cutters on the frequency-amplitude characteristics of chatter and on machined surface roughness. Vibration data were recorded using an experimental rig consisting of KISTLER 3-component dynamometer model 9257B, amplifier, scope meters and a PC.  Three different types of vibrations were observed. The first type was a low frequency vibration, associated with the interrupted nature of end mill operation. The second type of vibration was associated with the instability of the chip formation process and the third type was due to chatter. The frequency of the last type remained practically unchanged over a wide range of cutting speed.  It was further observed that chip-tool contact processes had considerable effect on the roughness of the machined surface.Key Words: Chatter, Cutting Conditions, Stable Cutting, Surface Roughness.

Characterisation, Performance and Optimisation of Nanocellulose Metalworking Fluid (MWF) for Green Machining Process

2021 ◽  
Vol 18 (4) ◽  
pp. 9188-9207
Author(s):  
Mahendran Samykano ◽  
J. Kananathan ◽  
K. Kadirgama ◽  
A. K. Amirruddin ◽  
D. Ramasamy ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Surface Roughness ◽  
Tool Wear ◽  
Feed Rate ◽  
Cutting Speed ◽  
Machining Process ◽  
Alumina Nanoparticles ◽  
Working Fluid ◽  
Depth Of Cut ◽  
Nanoparticle Concentration

The present research attempts to develop a hybrid coolant by mixing alumina nanoparticles with cellulose nanocrystal (CNC) into ethylene glycol-water (60:40) and investigate the viability of formulated hybrid nanocoolant (CNC-Al2O3-EG-Water) towards enhancing the machining behavior. The two-step method has been adapted to develop the hybrid nanocoolant at various volume concentrations (0.1, 0.5, and 0.9%). Results indicated a significant enhancement in thermal properties and tribological behaviour of the developed hybrid coolant. The thermal conductivity improved by 20-25% compared to the metal working fluid (MWF) with thermal conductivity of 0.55 W/m℃. Besides, a reduction in wear and friction coefficient was observed with the escalation in the nanoparticle concentration. The machining performance of the developed hybrid coolant was evaluated using Minimum Quantity Lubrication (MQL) in the turning of mild steel. A regression model was developed to assess the deviations in the tool flank wear and surface roughness in terms of feed, cutting speed, depth of the cut, and nanoparticle concentration using Response Surface Methodology (RSM). The mathematical modeling shows that cutting speed has the most significant impact on surface roughness and tool wear, followed by feed rate. The depth of cut does not affect surface roughness or tool wear. Surface roughness achieved 24% reduction, 39% enhancement in tool length of cut, and 33.33% improvement in tool life span. From this, the surface roughness was primarily affected by spindle cutting speed, feed rate, and then cutting depth while utilising either conventional water or composite nanofluid as a coolant. The developed hybrid coolant manifestly improved the machining behaviour.

Cutting Forces and Surface Roughness in High-Speed End Milling of Ti6Al4V

2013 ◽  
Vol 589-590 ◽  
pp. 76-81
Author(s):  
Fu Zeng Wang ◽  
Jun Zhao ◽  
An Hai Li ◽  
Jia Bang Zhao
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Cutting Forces ◽  
High Speed ◽  
End Milling ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Wide Range ◽  
Radial Depth ◽  
Coated Carbide

In this paper, high speed milling experiments on Ti6Al4V were conducted with coated carbide inserts under a wide range of cutting conditions. The effects of cutting speed, feed rate and radial depth of cut on the cutting forces, chip morphologies as well as surface roughness were investigated. The results indicated that the cutting speed 200m/min could be considered as a critical value at which both relatively low cutting forces and good surface quality can be obtained at the same time. When the cutting speed exceeds 200m/min, the cutting forces increase rapidly and the surface quality degrades. There exist obvious correlations between cutting forces and surface roughness.

A Prediction Model of Surface Roughness in Micro End Milling

2015 ◽  
Vol 727-728 ◽  
pp. 354-357
Author(s):  
Mei Xia Yuan ◽  
Xi Bin Wang ◽  
Li Jiao ◽  
Yan Li
Keyword(s):  
Surface Roughness ◽  
Prediction Model ◽  
Feed Rate ◽  
End Milling ◽  
Orthogonal Experiment ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Micro Milling ◽  
Cutting Depth ◽  
Micro End Milling

Micro-milling orthogonal experiment of micro plane was done in mesoscale. Probability statistics and multiple regression principle were used to establish the surface roughness prediction model about cutting speed, feed rate and cutting depth, and the significant test of regression equation was done. On the basis of successfully building the prediction model of surface roughness, the diagram of surface roughness and cutting parameters was intuitively built, and then the effect of the cutting speed, feed rate and cutting depth on the small structure surface roughness was obtained.

scholarly journals Investigate the Effect of Cutting Parameters on Surface Roughness When Milling X12m Steel

2021 ◽  
pp. 258-263
Author(s):  
Do Thi Kim Lien ◽  
Nguyen Dinh Man ◽  
Phung Tran Dinh
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Feed Rate ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Face Milling ◽  
Negligible Effect ◽  
Depth Of Cut ◽  
The Relationship

In this paper, an experimental study on the effect of cutting parameters on surface roughness was conducted when milling X12M steel. The cutting tool used in this study is a face milling cutter. The material that is used to make the insert is the hard alloy T15K6. The cutting parameters covered in this study include the cutting speed, the feed rate and depth of cut. The experiments are performed in the form of a rotating center composite design. The analysis shows that for both Ra and Rz: (1) the feed rate has the greatest influence on the surface roughness while the depth of cut, the cutting speed has a negligible effect on the surface roughness. (2) only the interaction between the feed rate and the depth of the cut has a significant effect on both Ra and Rz while the interaction between the cutting speed and the feed rate, the interaction between the cutting speed and the depth of cut have a negligible effect on surface roughness. A regression equation showing the relationship between Ra, Rz, and cutting parameters has also been built in this study.

scholarly journals Analysis and Optimization of Machining Hardened Steel AISI 4140 with Self-Propelled Rotary Tools

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6106
Author(s):  
Waleed Ahmed ◽  
Hussien Hegab ◽  
Atef Mohany ◽  
Hossam Kishawy
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Inclination Angle ◽  
Feed Rate ◽  
Cutting Speed ◽  
Weight Ratio ◽  
Hardened Steel ◽  
Machining Process ◽  
Aisi 4140 ◽  
Steel Aisi

It is necessary to improve the machinability of difficult-to-cut materials such as hardened steel, nickel-based alloys, and titanium alloys as these materials offer superior properties such as chemical stability, corrosion resistance, and high strength to weight ratio, making them indispensable for many applications. Machining with self-propelled rotary tools (SPRT) is considered one of the promising techniques used to provide proper tool life even under dry conditions. In this work, an attempt has been performed to analyze, model, and optimize the machining process of AISI 4140 hardened steel using self-propelled rotary tools. Experimental analysis has been offered to (a) compare the fixed and rotary tools performance and (b) study the effect of the inclination angle on the surface quality and tool wear. Moreover, the current study implemented some artificial intelligence-based approaches (i.e., genetic programming and NSGA-II) to model and optimize the machining process of AISI 4140 hardened steel with self-propelled rotary tools. The feed rate, cutting velocity, and inclination angle were the selected design variables, while the tool wear, surface roughness, and material removal rate (MRR) were the studied outputs. The optimal surface roughness was obtained at a cutting speed of 240 m/min, an inclination angle of 20°, and a feed rate of 0.1 mm/rev. In addition, the minimum flank tool wear was observed at a cutting speed of 70 m/min, an inclination angle of 10°, and a feed rate of 0.15 mm/rev. Moreover, different weights have been assigned for the three studied outputs to offer different optimized solutions based on the designer’s interest (equal-weighted, finishing, and productivity scenarios). It should be stated that the findings of the current work offer valuable recommendations to select the optimized cutting conditions when machining hardened steel AISI 4140 within the selected ranges.

scholarly journals Effects of Turning Parameters and Parametric Optimization of the Cutting Forces in Machining SiCp/Al 45 wt% Composite

Metals ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 840 ◽  
Author(s):  
Rashid Ali Laghari ◽  
Jianguang Li ◽  
Mozammel Mia
Keyword(s):  
Mathematical Model ◽  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
Desirability Function ◽  
Interactive Effect ◽  
Cutting Speed ◽  
Experimental Results ◽  
Machining Process ◽  
Depth Of Cut

Cutting force in the machining process of SiCp/Al particle reinforced metal matrix composite is affected by several factors. Obtaining an effective mathematical model for the cutting force is challenging. In that respect, the second-order model of cutting force has been established by response surface methodology (RSM) in this study, with different cutting parameters, such as cutting speed, feed rate, and depth of cut. The optimized mathematical model has been developed to analyze the effect of actual processing conditions on the generation of cutting force for the turning process of SiCp/Al composite. The results show that the predicted parameters by the RSM are in close agreement with experimental results with minimal error percentage. Quantitative evaluation by using analysis of variance (ANOVA), main effects plot, interactive effect, residual analysis, and optimization of cutting forces using the desirability function was performed. It has been found that the higher depth of cut, followed by feed rate, increases the cutting force. Higher cutting speed shows a positive response by reducing the cutting force. The predicted and experimental results for the model of SiCp/Al components have been compared to the cutting force of SiCp/Al 45 wt%—the error has been found low showing a good agreement.

Sign in / Sign up

Export Citation Format

Share Document