scholarly journals A slow pyrolysis biochar derived from Tetrapanax papyriferum petiole as an effective sorbent for removing copper ions from aqueous solution

BioResources ◽  
2019 ◽  
Vol 14 (2) ◽  
pp. 4430-4453
Author(s):  
Wenqi Li ◽  
Liping Zhang ◽  
Ying Guan ◽  
Zhihan Tong ◽  
Xiang Chen ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Mechanism ◽  
Adsorption Process ◽  
Copper Ions ◽  
Maximum Adsorption Capacity ◽  
Transmission Electron ◽  
Tetrapanax Papyriferum ◽  
Pseudo Second Order ◽  
Nanopore Structure ◽  
Effective Sorbent

Biochar derived from Tetrapanax papyriferum petioles at different pyrolysis temperatures was used to remove copper from aqueous solution. Abundant porous structures were observed with scanning electron microscopy, and transmission electron microscope images revealed a unique layered nanopore structure. A high pyrolytic temperature resulted in a biochar with a higher surface area, ash content, and mineral element content. The maximum adsorption capacity of T. papyriferum petiole biochar (TBC) was 182 mg/g. The Langmuir adsorption isotherm model and pseudo-second-order kinetics model were most suitable for describing the adsorption process, indicating that adsorption takes place at specific homogeneous sites within the adsorbent. The calculated ΔH° values indicated that the adsorption process was endothermic. The adsorption mechanism for TBC was attributed to precipitation, ion exchange, C-π interactions, and complexation. Thus, the biochar used in this study is a promising environmentally friendly and effective adsorbent for removing Cu2+ ions from an aqueous solution.

scholarly journals Removal of Chrysoidine Y from water by Graphene-based Nanocomposite Derivatives with Magnetic Chitosa Nanocomposite

2019 ◽  
Vol 4 (02) ◽  
pp. 17-33
Author(s):  
Farid Abu Shammala ◽  
Barry Chiswell
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Maximum Adsorption Capacity ◽  
Order Model ◽  
Intraparticle Diffusion Model ◽  
First Order ◽  
Transmission Electron ◽  
Pseudo Second Order ◽  
Adsorption Kinetics And Isotherm ◽  
Nanocomposite Adsorbent

This article describes a novel and efficient MCTS/GO nanocomposite for the accumulation and removal of a hazardous azo dye (Chrysoidine Y) from its aqueous solutions. Magnetic Chitosan /graphene oxide (MCTS/GO) nanocomposite adsorbent was prepared by wet-spinning technique, was used as accumulation and removal of Chrysoidine Y from aqueous solution. The structure and morphology of MCTS/GO nanocomposites were investigated using transmission electron microscope (TEM) and Fourier transform infrared (FTIR) spectroscopy were carried out on the MCTS/GO before the Chrysoidine Y (CY) accumulation experiments. The adsorption kinetics and isotherm studies were conducted under different conditions (pH = 3-7 and CY concentration = 100-400 mg/L) to examine the accumultion efficiency of the MCTS/GO towards CY in aqueous solution. The kinetics data of the adsorption process were analyzed using different kinetic models in order to investigate the adsorption behavior of CY on MCTS/GO. The results showed that the maximum adsorption capacity of the MCTS/GO nanocomposites towards CY can achieve up to ~700 mg/g for the adsorption at 300 mg/L CY. Kinetic data of adsorption process were found to fit pseudo-second order model as compared with pseudo-first-order model. The intraparticle diffusion model suggested that the adsorption process of MCTS/GO towards CY was dominated by the external mass transfer of CY molecules to the surface of MCTS/GO.

Preparation of bio-based magnetic adsorbent and application for efficient removal of Cd(II) from water

2018 ◽  
Vol 77 (5) ◽  
pp. 1313-1323 ◽  
Author(s):  
Jianjun Zhou ◽  
Xionghui Ji ◽  
Xiaohui Zhou ◽  
Jialin Ren ◽  
Yaochi Liu
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Maximum Adsorption Capacity ◽  
Magnetic Adsorbent ◽  
Order Model ◽  
Efficient Removal ◽  
Adsorption Ability ◽  
Adsorption Sites ◽  
Pseudo Second Order

Abstract A novel magnetic bio-adsorbent (MCIA) was developed, characterized and tested for its Cd(II) removal from aqueous solution. MCIA could be easily separated from the solution after equilibrium adsorption due to its super-paramagnetic property. The functional and magnetic bio-material was an attractive adsorbent for the removal of Cd(II) from aqueous solution owing to the abundant adsorption sites, amino-group and oxygen-containing groups on the surface of Cyclosorus interruptus. The experimental results indicated that the MCIA exhibited excellent adsorption ability and the adsorption process was spontaneous and endothermic. The adsorption isotherm was consistent with the Langmuir model. The adsorption kinetic fitted the pseudo-second-order model very well. The maximum adsorption capacity of Cd(II) onto MCIA was 40.8, 49.4, 54.6 and 56.6 mg/g at 293, 303, 313 and 323 K, respectively. And the MCIA exhibited an excellent reusability and impressive regeneration. Therefore, MCIA could serve as a sustainable, efficient and low-cost magnetic adsorbent for Cd(II) removal from aqueous solution.

Adsorptive removal of PPCPs by biomorphic HAP templated from cotton

2016 ◽  
Vol 74 (1) ◽  
pp. 276-286 ◽  
Author(s):  
Bin Huang ◽  
Dan Xiong ◽  
Tingting Zhao ◽  
Huan He ◽  
Xuejun Pan
Keyword(s):  
Adsorption Mechanism ◽  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Kinetic Studies ◽  
Precipitation Method ◽  
Adsorptive Removal ◽  
Transmission Electron ◽  
Initial Ph ◽  
Pseudo Second Order ◽  
Co Precipitation

Biomorphic nano-hydroxyapatite (HAP) was fabricated by a co-precipitation method using cotton as bio-templates and employed in adsorptive removal of ofloxacin (OFL) and triclosan (TCS) that are two representative pharmaceuticals and personal care products (PPCPs). The surface area and porosity, crystal phase, functional group, morphology and micro-structure of the synthesized HAP were characterized by Brunauer–Emmett–Teller isotherm, X-ray powder diffraction, Fourier transform infrared spectroscopy, scanning electron macroscopic and transmission electron microscopy. The effects of initial pH, ionic strength, initial concentration, contact time and temperature on the removal of PPCPs were studied in a batch experiment. The adsorption of OFL and TCS was rapid and almost accomplished within 50 min. Kinetic studies indicated that the adsorption process of OFL and TCS followed the pseudo-first-order and pseudo-second-order models, respectively. The Freundlich isotherm described the OFL adsorption process well but the adsorption of TCS fitted the Langmuir isotherm better. Thermodynamics and isotherm parameters suggested that both OFL and TCS adsorption were feasible and spontaneous. Hydrogen bond and Lewis acid–base reaction may be the dominating adsorption mechanism of OFL and TCS, respectively. Compared to other adsorbents, biomorphic HAP is environmentally friendly and has the advantages of high adsorption capacity, exhibiting potential application for PPCPs removal.

scholarly journals REMOVAL OF Pb2+ FROM AQUEOUS SOLUTION BY ADSORPTION ONTO COMPOSITE BASED ON EUCALYPTUS LEAF AND POLYANILINE

2017 ◽  
Vol 55 (1) ◽  
pp. 54
Author(s):  
Le Cao The ◽  
Vu Minh Tan ◽  
Phan Thi Binh
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Sem Images ◽  
Adsorption Data ◽  
Freundlich Adsorption Isotherm ◽  
Pseudo Second Order ◽  
Ir Analysis ◽  
Polymerization Method

Composite based on eucalyptus leaf and polyaniline (EL-PANi) was prepared by chemical polymerization method. It showed that the function groups belonging to polyaniline and eucalyptus leaf were found through IR analysis and the nanostructure of composite was explained by SEM images. The adsorption of  Pb2+ was carried out onto composite in aqueous solution via varying pH, contact time, and its initial concentration. The experimental adsorption data fitted well into Freundlich adsorption isotherm model (r2 = 0.9873). The adsorption process followed pseudo-second order kinetic with r2 = 0.9995. The maximum adsorption capacity of Pb2+ onto that composite was 172.4138 mg/g  by Langmuir equation and KF was 58.7527 mg/g by Freundlich one.

scholarly journals Treatment of effluent from fertilizer industry by adsorption on willow sawdust-removal of Ni(II) and Cd(II) from the effluent

2021 ◽  
pp. 1-12
Author(s):  
Raafia Najam ◽  
Syed Muzaffar Ali Andrabi
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
The World ◽  
Pseudo Second Order ◽  
Almost All ◽  
Willow Tree

Sawdust of willow has been investigated as an adsorbent for the removal of Ni(II), and Cd(II) ions from aqueous solution. Since willow tree is widely grown in almost all parts of Kashmir, it can be a common most easily available, sustainable, low cost adsorbent for the treatment of wastewaters in this part of the world where growing industrialization is affecting water quality like elsewhere in the world. Therefore, it is worthwhile to investigate the potential of sawdust of willow tree as an adsorbent for the removal of Ni(II) and Cd(II) ions from aqueous solution as a first step. Batch experiments were conducted to study the effect of some parameters such as contact time, initial concentration of metal ions, solution pH and temperature. Langmuir and Freundlich models were employed for the mechanistic analysis of experimental data obtained. Results reveal that in our system adsorption follows the Langmuir isotherm. The maximum adsorption capacity of Ni(II) and Cd(II) were found to be 7.98 and 7.11 mg/g respectively at optimum conditions. The pseudo-first-order and pseudo-second-order models were employed for kinetic analysis of adsorption process. The adsorption process follows pseudo-second-order kinetics. The efficacy of the adsorbent in the treatment of effluent from fertilizer factory has been investigated and the results have been found encouraging.

Fabrication of a novel graphene oxide/β-FeOOH composite and its adsorption behavior for copper ions from aqueous solution

2015 ◽  
Vol 44 (22) ◽  
pp. 10448-10456 ◽  
Author(s):  
Tingshun Jiang ◽  
Lu Yan ◽  
Lei Zhang ◽  
Yingying Li ◽  
Qian Zhao ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Graphene Oxide ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Copper Ions ◽  
Removal Rate ◽  
Second Order ◽  
Adsorption Behavior ◽  
Kinetics Model ◽  
Pseudo Second Order

A graphene oxide/β-FeOOH composite was prepared and its adsorption capacity was evaluated by Cu2+removal. The adsorption process was well fitted with the pseudo-second-order kinetics model. The removal rate of Cu2+reached 93.8%.

Research on Lead (II) Adsorption Mechanism from Aqueous Solution by Calcium Carbonate Modified Diatomite Absorbent

2018 ◽  
Vol 921 ◽  
pp. 21-28 ◽  
Author(s):  
Li Li Ma ◽  
Qing Lin Xie ◽  
Nan Chun Chen ◽  
Hui Xu ◽  
Hai Miao Zhou ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Calcium Carbonate ◽  
Adsorption Isotherms ◽  
Adsorption Mechanism ◽  
Adsorption Process ◽  
Analytical Techniques ◽  
X Ray Diffraction ◽  
X Ray ◽  
Pseudo Second Order ◽  
Modified Diatomite

In this study, calcium carbonate was used to coat and link the surface of diatomite for the formation of a novel modified adsorbent (referred to as Ca–diatomite). Various analytical techniques were used to characterize structure and mechanisms of modification and adsorption process, like Scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD). Results showed that that Calcium carbonate had been successful grafted onto the surface of diatomite after modification, and Calcium carbonate modification improved the adsorption performance of diatomite for the removal of lead (II) ions from aqueous solution. Ca–diatomite adsorption isotherms and adsorption kinetics were also been studied. The adsorption isotherms and the kinetic data were best fitted with the Langmuir model and pseudo-second-order kinetics, respectively.

scholarly journals Removal of Methylene Blue Dye From Aqueous Solution Using PDADMAC Modified ZSM-5 Zeolite as a Novel Adsorbent 

2021 ◽  
Author(s):  
Sabarish Radoor ◽  
Jasila Karayil ◽  
Aswathy Jayakumar ◽  
Jyotishkumar Parameswaranpillai ◽  
Suchart Siengchin
Keyword(s):  
Aqueous Solution ◽  
Methylene Blue ◽  
Contact Time ◽  
Adsorption Process ◽  
Nitrogen Adsorption ◽  
Second Order ◽  
Blue Dye ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Pseudo Second Order

Abstract In the present work, we modified ZSM-5 zeolite using a bio polymer poly (diallyl dimethyl ammonium chloride) and employed it for the removal of cationic dye, methylene blue from aqueous solution. The chemical and physical properties of the modified ZSM-5 zeolite were investigated using XRD, FTIR, SEM, TEM, nitrogen adsorption, TGA and 27Al NMR. Modified ZSM-5 zeolite possesses high surface area and pore diameter which was confirmed from SEM, TEM and nitrogen adsorption analysis. Adsorption of methylene blue on zeolite was investigated by batch adsorption technique. The effect of different parameters such as zeolite dosage, initial methylene blue concentration, temperature, pH and contact time on the adsorption process was discussed. Maximum adsorption capacity (4.31 mg/g) was achieved using 0.1g of modified ZSM-5 zeolite at the optimum conditions (initial dye concentration: 10 mg/L, pH: 10, temperature:30oC and contact time: 300 min). The experimental data were fitted into Langmuir and Freundlich models and the results indicate that the adsorption process followed Freundlich isotherm. Kinetic data were investigated using pseudo-first-order and pseudo-second-order models. Kinetic analysis indicates that pseudo-second-order model is more suitable to describe adsorption of MB on modified ZSM-5 zeolite. The reusability test suggests that the adsorbent could be reused at least six times without significant loss in removal efficiency.

Adsorption of Cu 2+ Ions from Aqueous Solution by NaOH Activated ZSM-5 Zeolite

2012 ◽  
Vol 482-484 ◽  
pp. 2568-2572
Author(s):  
Xu Zhuo Sun ◽  
Dong Jin Wan ◽  
Bo Li ◽  
Li Li Wang ◽  
Ning Wang ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Langmuir Model ◽  
Maximum Adsorption Capacity ◽  
Kinetics Study ◽  
Adsorption Efficiency ◽  
Equilibrium Isotherm ◽  
Naoh Solution ◽  
Pseudo Second Order

ZSM-5 zeolite was chemical activated by using NaOH solution to enhance the adsorption efficiency to Cu2+ in aqueous solution. The equilibrium isotherm of NaOH activated ZSM-5 zeolite showed that the Langmuir model gave a better fit to the experimental data. The maximum adsorption capacity of NaOH activated ZSM-5 zeolite was 40.49 mg/g. The adsorption capacity was increased nearly 3.3 times than unactivated zeolite by using 0.4M NaOH. The kinetics study showed that the pseudo-second-order kinetics model could be used to describe the adsorption process satisfactorily. The research also found that the coexisting of Pb2+ ion would greatly decrease the adsorption efficiency of activated zeolite from 99.35% decreased to 56.52%. Both ZSM-5 zeolite and NaOH activated ZSM-5 zeolite was characterized by SEM.

Adsorption of Phosphate onto Slag from Aqueous Solution

2012 ◽  
Vol 550-553 ◽  
pp. 2255-2258
Author(s):  
Bing Bing Liu ◽  
Hua Yong Zhang ◽  
Lu Yi Zhang
Keyword(s):  
Aqueous Solution ◽  
Adsorption Capacity ◽  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Langmuir Model ◽  
Phosphate Adsorption ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
High Adsorption ◽  
Pseudo Second Order

Phosphate adsorption from aqueous solution using slag was investigated as the function of pH, contact time and adsorbent dosage. The results showed that the optimum value of pH was 2. Both Langmuir isotherm and Freundlich isotherm model were fit to describe the phosphate adsorption, and the maximum adsorption capacity from Langmuir model calculated was 9.09 mg/L. The adsorption process on slag followed pseudo second-order kinetic. Due to the relatively high adsorption capacity, the slag has the potential for application to removal phosphate from wastewater.

Sign in / Sign up

Export Citation Format

Share Document