scholarly journals Properties of modified wood according to treatment technology and thermo-vacuum process for birch (Betula pendula Roth) veneers

BioResources ◽  
2020 ◽  
Vol 15 (2) ◽  
pp. 4150-4164
Author(s):  
Anete Meija-Feldmane ◽  
Ignazia Cuccui ◽  
Ilze Irbe ◽  
Andris Morozovs ◽  
Uldis Spulle
Keyword(s):  
Mass Loss ◽  
Betula Pendula ◽  
Brown Rot ◽  
Strength Loss ◽  
Decay Resistance ◽  
Treatment Technology ◽  
Betula Pendula Roth ◽  
Treatment Regimes ◽  
Brown Rot Fungus ◽  
Modified Wood

Thermally modified birch (Betula pendula Roth) veneers that had been subjected to wood treatment technology (WTT) or thermo vacuum (TV) processes were compared in this study. After modification of veneers in the range of temperatures from 160 °C to 218 °C and times from 0.5 h to 3 h, the color, mass loss, density, tensile strength, hygroscopicity, and decay resistance against brown rot fungus Coniophora puteana were determined. Treatment regimes with the greatest mass loss were at 217 °C for 3.0 h in TV (7.8%) and 160 °C for 0.8 h in the WTT (6.7%). As expected, wood mass loss correlated well with moisture exclusion efficiency (MEE) in all relative humidity (RH) environments (r = 0.95 to 0.99). Strength loss in the WTT was considerable compared to the TV process (57% and 40%, respectively). The resistance against brown rot fungus was moderate with a mass loss of 12% to 33%. Among the investigated samples, the regime 217/3.0/TV showed the best resistance against brown rot fungus and acceptable other properties.

Genetic variation in the decay resistance of Scots pine wood against brown rot fungus

2001 ◽  
Vol 31 (7) ◽  
pp. 1244-1249 ◽  
Author(s):  
Anni M Harju ◽  
Martti Venäläinen ◽  
Egbert Beuker ◽  
Pirkko Velling ◽  
Hannu Viitanen
Keyword(s):  
Genetic Variation ◽  
Mass Loss ◽  
Scots Pine ◽  
Brown Rot ◽  
Decay Resistance ◽  
Phenotypic Variance ◽  
Increment Core ◽  
Genetic Components ◽  
Brown Rot Fungus ◽  
The Mean

The role of genotype in the durability of Scots pine (Pinus sylvestris L.) wood against decay by brown rot fungus (Coniophora puteana (Schum. ex Fr.) Karst. (strain Bam EBW 15)) was studied in a laboratory test. The wood material was obtained from 32-year-old half-sib progenies of Scots pine. The increment core samples of sapwood and juvenile heartwood were decayed using a modification of the standardized EN 113 method. The mean densities of the sapwood and heartwood samples were 391 and 337 mg·cm–3, respectively, and the mean mass losses were 114 and 80 mg·cm–3, respectively. The additive genetic components were small compared with the total phenotypic variance, which resulted in small narrow-sense heritabilities in mass loss. The most marked feature was the wide phenotypic variation in mass loss observed in heartwood (range 199 mg·cm–3) compared with sapwood (range 72 mg·cm–3) samples. Low heritability, together with the relatively high coefficient of additive genetic variation (CVA) in heartwood mass loss, suggests that advances in breeding can only be made through intensive testing in the environments which the studied experiment represents.

Decay resistance of anhydride-modified Corsican pine sapwood exposed to the brown rot fungus Coniophora puteana

Holzforschung ◽  
2006 ◽  
Vol 60 (6) ◽  
pp. 625-629 ◽  
Author(s):  
Callum A.S. Hill ◽  
Michael D. Hale ◽  
Graham A. Ormondroyd ◽  
Jin H. Kwon ◽  
Simon C. Forster
Keyword(s):  
Brown Rot ◽  
Pinus Nigra ◽  
Decay Resistance ◽  
Exposure Test ◽  
Weight Percentage ◽  
Coniophora Puteana ◽  
Chemically Modified ◽  
Brown Rot Fungus ◽  
The Relationship ◽  
Modified Wood

Abstract Corsican pine (Pinus nigra) sapwood was chemically modified with acetic or hexanoic anhydride to a variety of weight gains. The modified wood was exposed to the brown rot fungus Coniophora puteana, and the relationship between weight loss due to decay and weight percentage gain, or degree of hydroxyl substitution, was determined in a 16-week exposure test. The effect of exposure time and the strain of C. puteana upon the decay protection threshold of acetylated Corsican pine was also examined.

Growth behavior of wood-destroying fungi in chemically modified wood: wood degradation and translocation of nitrogen compounds

Holzforschung ◽  
2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Lukas Emmerich ◽  
Maja Bleckmann ◽  
Sarah Strohbusch ◽  
Christian Brischke ◽  
Susanne Bollmus ◽  
...  
Keyword(s):  
Protective Action ◽  
Treated Wood ◽  
Untreated Wood ◽  
Brown Rot ◽  
Decay Resistance ◽  
White Rot ◽  
Decay Fungi ◽  
Chemically Modified ◽  
Decay Tests ◽  
Modified Wood

Abstract Chemical wood modification has been used to modify wood and improve its decay resistance. However, the mode of protective action is still not fully understood. Occasionally, outdoor products made from chemically modified timber (CMT) show internal decay while their outer shell remains intact. Hence, it was hypothesized that wood decay fungi may grow through CMT without losing their capability to degrade non-modified wood. This study aimed at developing a laboratory test set-up to investigate (1) whether decay fungi grow through CMT and (2) retain their ability to degrade non-modified wood. Acetylated and 1,3-dimethylol-4,5-dihydroxyethyleneurea (DMDHEU) treated wood were used in decay tests with modified ‘mantle specimens’ and untreated ‘core dowels’. It became evident that white rot (Trametes versicolor), brown rot (Coniophora puteana) and soft rot fungi can grow through CMT without losing their ability to degrade untreated wood. Consequently, full volume impregnation of wood with the modifying agent is required to achieve complete protection of wooden products. In decay tests with DMDHEU treated specimens, significant amounts of apparently non-fixated DMDHEU were translocated from modified mantle specimens to untreated wood cores. A diffusion-driven transport of nitrogen and DMDHEU seemed to be responsible for mass translocation during decay testing.

scholarly journals Particleboards from Recycled Thermally Modified Wood

Forests ◽  
2021 ◽  
Vol 12 (11) ◽  
pp. 1462
Author(s):  
Ján Iždinský ◽  
Zuzana Vidholdová ◽  
Ladislav Reinprecht
Keyword(s):  
Mechanical Properties ◽  
Urea Formaldehyde ◽  
Brown Rot ◽  
Decay Resistance ◽  
Raw Material ◽  
Modulus Of Rupture ◽  
Negative Effect ◽  
Serpula Lacrymans ◽  
Thermally Modified Wood ◽  
Modified Wood

In recent years, the production and consumption of thermally modified wood (TMW) has been increasing. Offcuts and other waste generated during TMWs processing into products, as well as already disposed products based on TMWs can be an input recycled raw material for production of particleboards (PBs). In a laboratory, 16 mm thick 3-layer PBs bonded with urea-formaldehyde (UF) resin were produced at 5.8 MPa, 240 °C and 8 s pressing factor. In PBs, the particles from fresh spruce wood and mixed particles from offcuts of pine, beech, and ash TMWs were combined in weight ratios of 100:0, 80:20, 50:50 and 0:100. Thickness swelling (TS) and water absorption (WA) of PBs decreased with increased portion of TMW particles, i.e., TS after 24 h maximally about 72.3% and WA after 24 h maximally about 64%. However, mechanical properties of PBs worsened proportionally with a higher content of recycled TMW—apparently, the modulus of rupture (MOR) up to 55.5% and internal bond (IB) up to 46.2%, while negative effect of TMW particles on the modulus of elasticity (MOE) was milder. Decay resistance of PBs to the brown-rot fungus Serpula lacrymans (Schumacher ex Fries) S.F.Gray increased if they contained TMW particles, maximally about 45%, while the mould resistance of PBs containing TMW particles improved only in the first days of test. In summary, the recycled TMW particles can improve the decay and water resistance of PBs exposed to higher humidity environment. However, worsening of their mechanical properties could appear, as well.

scholarly journals Resistance of thermally modified and pressurized hot water extracted Scots pine sapwood against decay by the brown-rot fungus Rhodonia placenta

2019 ◽  
Vol 78 (1) ◽  
pp. 161-171 ◽  
Author(s):  
Michael Altgen ◽  
Suvi Kyyrö ◽  
Olli Paajanen ◽  
Lauri Rautkari
Keyword(s):  
Cell Wall ◽  
Mass Loss ◽  
Scots Pine ◽  
Elevated Temperatures ◽  
Brown Rot ◽  
Decay Resistance ◽  
Hot Water ◽  
Decay Fungi ◽  
Effective Reduction ◽  
Cell Wall Porosity

AbstractThe thermal degradation of wood is affected by a number of process parameters, which may also cause variations in the resistance against decay fungi. This study compares changes in the chemical composition, water-related properties and decay resistance of Scots pine sapwood that was either thermally modified (TM) in dry state at elevated temperatures (≥ 185 °C) or treated in pressurized hot water at mild temperatures (≤ 170 °C). The thermal decomposition of easily degradable hemicelluloses reduced the mass loss caused by Rhodonia placenta, and it was suggested that the cumulative mass loss is a better indicator of an actual decay inhibition. Pressurized hot water extraction (HWE) did not improve the decay resistance to the same extent as TM, which was assigned to differences in the wood-water interactions. Cross-linking reactions during TM caused a swelling restraint and an effective reduction in moisture content. This decreased the water-swollen cell wall porosity, which presumably hindered the transport of degradation agents through the cell wall and/or reduced the accessibility of wood constituents for degradation agents. This effect was absent in hot water-extracted wood and strong decay occurred even when most hemicelluloses were already removed during HWE.

Effect of Heat Treatment on Decay Resistance of Chinese Fir and Pine

2012 ◽  
Vol 468-471 ◽  
pp. 1118-1122
Author(s):  
Yan Jun Li ◽  
Lan Xing Du ◽  
Gou Ying Hu ◽  
Xing Xia Ma
Keyword(s):  
Heat Treatment ◽  
Moisture Content ◽  
Treatment Time ◽  
Brown Rot ◽  
Decay Resistance ◽  
Chinese Fir ◽  
Heat Treatment Time ◽  
White Rot ◽  
Heat Treated ◽  
Brown Rot Fungus

To enhance decay resistance, the effect of heat treatment and the variation of chemical composition on Chinese Fir and Pine were investigated in this study — heat treatment temperature was 170°C, 190°C and 210°C, respectively, heat treatment time was 2, 3 and 4hours, respectively. Both of them were subsequently exposed to white-rot fungus and brown-rot fungus. The results showed that:(1) With the increasing of the heat treatment, decay resistance of Chinese Fir and Pine were improved, anti-corrosion of Pine after being heat treated at 190°C which were exposed to write-rot fungus can reach I, anti-corrosion of Chinese Fir after being heat treated at 170°C treated which were exposed to brown-rot fungus could reach I yet, After being heat treated at 210°C for 3 hours , the Chinese fir samples had no measurable weight loss when exposed to the write-rot fungus.(2) There was no remarkable influence on both Chinese Fir and Pine by heat treatment time.(3) The moisture content of Chinese Fir and Pine were lower than the moisture content that the rot fungus need, macromolecule chains such as cellulose and hemicellulose broke down, their contents decreased, and the hemicellulose decomposed into acetic acid, they prevented the growth of rot fungus.

scholarly journals Mode of action of brown rot decay resistance in modified wood: a review

Holzforschung ◽  
2014 ◽  
Vol 68 (2) ◽  
pp. 239-246 ◽  
Author(s):  
Rebecka Ringman ◽  
Annica Pilgård ◽  
Christian Brischke ◽  
Klaus Richter
Keyword(s):  
Cell Wall ◽  
Mode Of Action ◽  
Wood Decay ◽  
Brown Rot ◽  
Decay Resistance ◽  
Hydroxyl Groups ◽  
Decay Fungi ◽  
Brown Rot Decay ◽  
Thermally Modified Wood ◽  
Modified Wood

Abstract Chemically or physically modified wood materials have enhanced resistance to wood decay fungi. In contrast to treatments with traditional wood preservatives, where the resistance is caused mainly by the toxicity of the chemicals added, little is known about the mode of action of nontoxic wood modification methods. This study reviews established theories related to resistance in acetylated, furfurylated, dimethylol dihydroxyethyleneurea-treated, and thermally modified wood. The main conclusion is that only one theory provides a consistent explanation for the initial inhibition of brown rot degradation in modified wood, that is, moisture exclusion via the reduction of cell wall voids. Other proposed mechanisms, such as enzyme nonrecognition, micropore blocking, and reducing the number of free hydroxyl groups, may reduce the degradation rate when cell wall water uptake is no longer impeded.

scholarly journals Leachates of Thermally Modified Pine (Pinus sylvestris L.) Wood

2015 ◽  
Vol 34 (329) ◽  
pp. 26-31 ◽  
Author(s):  
Anete Meija-Feldmane
Keyword(s):  
Pinus Sylvestris ◽  
Mass Loss ◽  
Tannic Acid ◽  
Environmentally Friendly ◽  
Hazardous Substances ◽  
Environmental Aspects ◽  
Treatment Technology ◽  
Thermally Modified Wood ◽  
Main Components ◽  
Modified Wood

Abstract During the last decades, thermally modified wood has become an object of interest among the wood scientists as an environmentally friendly material, because nowadays environmental aspects of materials have become more and more significant. Leaching is one of the processes that occurs in outdoor use. The aim of this study was to evaluate concentration of potentially hazardous substances in leachates of thermally modified pine wood. Scots pine (Pinus sylvestris L.) wood was thermally modified using Wood Treatment Technology (WTT) company device at 170 °C for 1 hour (TMP170/1) and at 160 °C for 3 hours (TMP160/3) and the mass loss was calculated. Material preparation and leaching procedure was made according to standard LVS EN 84:2000. In obtained leachates, the content of sugars, acetic acid, furfural and tannic acid were determined. Results showed that the total wood mass loss was 7.1 ± 1.4% (n=20) for TMP170/1 and 4.0 ± 1.6% (n=20) for TMP160/3. The initial leaching velocity differs between both modes and is higher for TMP160/3. The velocity decreases exponentially with immersion time and reaches plateau after 7th (5 days) immersion, but leaching still continues after the 9th immersion (14 days). The main components in leachates were tannic acid and pentoses. Among all studied compounds furfural is the hardest leachable one. Thermally modified wood treated at TMP170/1 is more environmentally friendly due to less water leachable substances. It is worth looking forward by investigating volatile organic compounds emissions in the air as it also could give high impact on human health.

scholarly journals Fungal decay resistance of wood reacted with phosphorus pentoxide-amine system

Holzforschung ◽  
2004 ◽  
Vol 58 (3) ◽  
pp. 311-315 ◽  
Author(s):  
H.-L. Lee ◽  
G.C. Chen ◽  
R.M. Rowell
Keyword(s):  
Brown Rot ◽  
Decay Resistance ◽  
Phosphorus Pentoxide ◽  
White Rot ◽  
White Rot Fungus ◽  
Gloeophyllum Trabeum ◽  
Brown Rot Fungus ◽  
Nitro Derivatives ◽  
Amine System

Abstract Resistance of wood reacted in situ with phosphorus pentoxide-amine to the brown-rot fungus Gloeophyllum trabeum and white-rot fungus Trametes versicolor was examined. Wood reacted with either octyl, tribromo, or nitro derivatives were more resistant to both fungi. Threshold retention values of phosphoramide-reacted wood to white-rot fungus T. versicolor ranged from 2.9 to 13.3 mmol, while these for brown-rot fungus G. trabeum ranged from 8.1 to 19.2 mmol. Wood reacted with phosphoramide tested to be more resistant to white-rot than brown-rot attack.

scholarly journals Feasibility of Manufacturing Strand-Based Wood Composite Treated with β-Cyclodextrin–Boric Acid for Fungal Decay Resistance

Polymers ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 274 ◽  
Author(s):  
Lili Cai ◽  
Hyungsuk Lim ◽  
Nicholas C. Fitzkee ◽  
Bojan Cosovic ◽  
Dragica Jeremic
Keyword(s):  
Boric Acid ◽  
Mass Loss ◽  
Chemical Shifts ◽  
Brown Rot ◽  
Decay Resistance ◽  
Attenuated Total Reflection ◽  
Fungal Decay ◽  
Scanning Calorimetry ◽  
Decay Fungi ◽  
Average Mass

The feasibility of using β-cyclodextrin (βCD) as an eco-friendly carrier of boric acid for the protection of strand-based wood composites against decay fungi was evaluated. The formation of a βCD–boric acid (βCD–B) complex was confirmed by the appearance of the boron–oxygen bond by using attenuated total reflection–Fourier transform infrared spectroscopy. Chemical shifts of around 6.25 and 1.41 ppm were also observed in 1H Nuclear Magnetic Resonance (NMR) and 11B NMR spectra, respectively. The βCD–B preservatives at two levels (5 and 10 wt.%) were uniformly blended with southern pine strands that were subsequently sprayed with polymeric methylene diphenyl diisocyanate (pMDI) resin. The blended strands were formed into a loose mat by hand and consolidated into 25 × 254 × 12 mm oriented strand boards (OSB) using a hot-press. The OSB panels were cut to end-matched internal bonding (IB) strength and fungal decay resistance test specimens. The vertical density profiles (VDPs) of the IB specimens were measured using an X-ray based density profiler and the specimens with statistically similar VDPs were selected for the IB and decay tests. The IB strength of the treated specimens was lower than the control specimens but they were above the required IB strength of heavy-duty load-bearing boards for use in humid conditions, specified in the BS EN 300:2006 standard. The reduced IB of preservative-treated OSB boards could be explained by the destabilized resin upon the addition of the βCD–B complex, as indicated by the differential scanning calorimetry (DSC) results. The resistance of the OSB panels against two brown-rot fungi (i.e., G. trabeum or P. placenta) was evaluated before and after accelerated leaching cycles. The treated OSBs exposed to the fungi showed an average mass loss of lower than 3% before leaching, while the untreated OSBs had 49 and 35% mass losses due to decay by G. trabeum or P. placenta, respectively. However, upon the leaching, the treatment provided protection only against G. trabeum to a certain degree (average mass loss of 15%). The experimental results suggest that protection efficacy against decay fungi after leaching, as well as the adhesion of the OSB strands, can be improved by increasing the amount of pMDI resin.

Sign in / Sign up

Export Citation Format

Share Document